MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

Investigating the potential of functionalized MCM-41 on adsorption of Remazol Red dye

The modification of MCM-41 was performed with 3-aminopropropyltrimethoxysilane. The structural order and textural properties of the synthesized materials were studied by X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetry/differential thermogravimetry, nitrogen adsorption, and desorption analysis. The adsorption capacity of NH₂-MCM-41 was studied with Remazol Red dye. The following parameters were studied in the adsorption process: pH, temperature, adsorbent dosage, and initial concentration. The desorption process was studied in different concentrations of NaOH solutions. The Freundlich isotherm model was found to be fit with the equilibrium isotherm data. Kinetics of adsorption follows the modified Avrami rate equation. The maximum adsorption capacity was estimated to be 45.9 mg?g^?1, with removal of the dye of 99.1 %. The NH₂-MCM-41 material exhibited high desorption capacity with 98.1 %.     

Adsorption of mesitylene via mesoporous adsorbents

Mesitylene (or 1,3,5-trimethylbenzene) is a volatile organic compound emitted from various industrial processes, e.g., spray coating. Its emissions have become a critical issue because mesitylene is toxic and cannot be removed using traditional adsorbents, e.g., zeolite (H-ZSM-5; the diameter of mesitylene molecules is greater than the pore size of H-ZSM-5). Hence, an adsorbent with a large pore size, MCM-41, is used in this study to investigate its adsorption capacity for mesitylene and compare with that of H-ZSM-5. Experimental results reveal that MCM-41 without Al₂O₃ exhibits a good adsorption capacity (184 mg/g) for the gas stream containing 100 ppm of mesitylene at a relative humidity of 10%. The adsorption kinetics is well described by the Freundlich isotherm. Furthermore, experimental results reveal that MCM-41 is effective for the adsorption of low concentrations (10 ppm) of mesitylene. In addition, adsorption–desorption tests revealed that the sample MCM-41-AS is stable to sustain the adsorption capacity after 10 adsorption–desorption cycles. After 10 adsorption–desorption cycles, MCM-41-AS retains 92.4% of its initial adsorption capacity (170 vs. 184 mg/g). Finally, MCM-41 and H-ZSM-5 in series are effective for the simultaneous removal of mesitylene and toluene in the gas stream.

Implications: This study aims to improve the performance of adsorbent for mesitylene, which is typically applied in the spray-coating industry. The zeolite MCM-41-AS is selected as a candidate for the investigation. Experimental results reveal that MCM-41-AS exhibits a good adsorption capacity for mesitylene and that it can be integrated with H-ZSM-5-25 for the simultaneous adsorption of mesitylene and toluene.     

Determination of the Adsorption Isotherm of Vapor-Phase Mercury Chloride on Powdered Activated Carbon Using Thermogravimetric Analysis

Abstract

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl₂ was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl₂ were 1.75, 0.688, and 0.230 mg of HgCl₂ per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 °C for 500 µg/m³ of HgCl₂, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer–Emmett–Teller (BET) models were used to simulate the adsorption of HgCl₂. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 °C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 °C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl₂ by PAC-derived carbon black favored adsorption at various HgCl₂ concentrations and temperatures.     

Adsorption of Cu2+ and methyl orange from aqueous solutions by activated carbons of corncob-derived char wastes

Corncob-derived char wastes (CCW) obtained from biomass conversion to syngas production through corncob steam gasification, which were often discarded, were utilized for preparation of activated carbon by calcination, and KOH and HNO₃ activation treatments, on the view of environment protection and waste recycling. Their adsorption performance in the removal of heavy metal ions and dye molecules from wastewater was evaluated by using Cu²⁺ and methyl orange (MO) as the model pollutant. The surface and structure characteristics of the CCW-based activated carbons (CACs) were investigated by N₂ adsorption, CO₂ adsorption, FT-IR, and He-TPD. The adsorption capacity varied with the activation methods of CACs and different initial solution concentrations, indicating that the adsorption behavior was influenced by not only the surface area and porosity but also the oxygen functional groups on the surface of the CACs. The equilibrium adsorption data were analyzed with the Langmuir, Freundlich, and Temkin isotherm models, and the adsorption kinetics was evaluated by the pseudo-first-order and pseudo-second-order models.     

改性玉米秸秆吸附Cu2+的动力学和热力学

本研究用ZnCl2作为活化剂,使用功率640 W的微波照射4 min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响,并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明:投加量为0.2 g,pH为6,改性玉米秸秆对Cu2+具有很好的吸附效果,吸附在8 h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程,其反应的吉布斯自由能△G<0,为自发反应过程。     

硅烷化改性MCM-41负载戊二酸锌催化CO2与环氧丙烷共聚制备可降解材料

以三甲基氯硅烷(TMCS)为硅烷化试剂,对MCM-41分子筛进行表面改性处理,并以此为载体制备负载型戊二酸锌催化剂(ZnGA/TMCS-MCM-41);采用红外光谱、氮气吸附-脱附和X射线衍射等分析手段对催化剂进行表征,结果表明:三甲基氯硅烷基团被成功接枝到MCM-41分子筛表面,形成比表面积略低的硅烷化MCM-41载体,但其骨架未被破坏,负载活性物质过程中,戊二酸锌能以更小的粒径均匀分散到载体的表面;聚合反应实验表明,与单纯戊二锌催化剂相比,ZnGA/TMCS-MCM-41催化剂对CO2与环氧丙烷(PO)的共聚反应显示出更高的催化效率和更快的反应速度,在反应34 h后催化效率达到86.3 g聚合物/g ZnGA;红外光谱和核磁分析表明所得共聚产物中碳酸酯结构含量大于95.8%。     

In vitro study of oxytetracycline adsorption on activated charcoal

Abstract

In vitro adsorption experiments simulating pH in gastric environment and using Langmuir isotherm, showed that 408 mg of oxytetracycline was adsorbed per gram of activated charcoal. Langmuir isotherm fitted adsorption data better than a Freundlich isotherm. Freundlich isotherm showed a specific adsorption capacity of 518 mg/g for activated charcoal. Both isotherm parameters indicated a strong oxytetracycline adsorption on activated charcoal in terms of quantity and binding strength. The results demonstrate that the concomitant use of oxytetracyline and activated charcoal should be avoided.     

Kinetics and isotherm modeling of azoxystrobin and imidacloprid retention in biomixtures

The paper reports the kinetics and adsorption isotherm modeling for imidacloprid (IMIDA) and azoxystrobin (AZOXY) in rice straw (RS)/corn cob (CC) and peat (P)/compost (C) based biomixtures. The pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich and intraparticle diffusion models were used to describe the kinetics. The adsorption data were subjected to the Langmuir and the Freundlich isotherms. Results (r²_Adj values) suggested that the modified Elovich model was the best suited to explain the kinetics of IMIDA sorption while different models explained AZOXY sorption kinetics in different biomixtures (PFO in RS?+?C and RS?+?P; PSO in CC?+?P and Elovich in CC?+?C). Biomixtures varied in their capacity to adsorb both pesticides and the adsorption coefficient (K_d) values were 116.8–369.24 (AZOXY) and 24.2–293.4 (IMIDA). The Freundlich isotherm better explained the sorption of both pesticides. Comparison analysis of linear and nonlinear method for estimating the Freundlich adsorption constants was made. In general, r²_Adj values were higher for the nonlinear fit (AZOXY?=?0.938–0.982; IMIDA?=?0.91–0.970) than the linear fit (AZOXY?=?0.886–0.993; IMIDA?=?0.870–0.974) suggesting that the nonlinear Freundlich equation better explained the sorption. The rice straw-based biomixtures performed better in adsorbing both the pesticides and can be used in bio-purification systems.     

玉米秸秆活性炭的制备及其吸附动力学研究

以玉米秸秆为原材料,采用ZnCl2活化法制备玉米秸秆活性炭,吸附次甲基蓝染料废水,进行动力学分析。本实验用Langmuir和Freundlich模型对吸附等温线进行拟合,结果表明,玉米秸秆活性炭对次甲基蓝的吸附与Langmuir方程拟合良好,R2=0.9857。采用Lagergren准一级速率模型、Lagergren准二级速率模型、Bangham动力学方程和Elovich动力学方程分别对秸秆活性炭吸附次甲基蓝溶液进行吸附动力学拟合,通过分析得出吸附过程与Lagergren准二级速率模型拟合最好,R2=0.9979。秸秆活性炭对次甲基蓝的最大吸附量达到909.09 mg/g,具有很高的吸附能力。     

“氧化镁/活性炭”新型吸附剂的制备及其对Cr(VI)的吸附研究

以氯化镁和造纸草浆黑液为原料,采用物理活化法制得“氧化镁/活性炭”新型吸附剂,其比表面积（BET）为388.96 m²/g、总孔容积为0.40 mL/g。测定了这种吸附剂对水中Cr(VI)的吸附性能,考察了吸附时间、pH值、吸附剂投加量、初始浓度等因素对Cr(VI)的吸附量和脱除率的影响,研究所得吸附水溶液中Cr(VI)的最佳条件为：吸附时间为120 min,吸附剂投加量为2 g/L,pH值为2。“氧化镁/活性炭”新型吸附剂对Cr(VI)的吸附过程符合Freundlich等温式。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N2吸附-脱附曲线、FT—IR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu2＋的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869．5m。／g,孔容为0．97cm3／g,平均孔径为3．3nm;溶液pH为5—6时,MCM-41对Cu2＋的去除效果最好;MCM-41对Cu3＋的最大吸附吸附容量36．3mg／g;MCM-41对Cu2＋的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

Adsorption of glyphosate on Brazilian subtropical soils rich in iron and aluminum oxides

Abstract

We investigated the adsorption of glyphosate onto five subtropical soils of Paraná and São Paulo states, Brazil, a region of intense agricultural activities, aiming at the determination of kinetic and isotherm adsorption parameters which enable the evaluation of the potential leaching of the herbicide. The adsorption was fast, being described by the pseudo-second order and intraparticle diffusion models, thus suggesting that mixed mechanisms are involved. The Oxisol containing the highest concentrations of metal oxides (209.5?g kg^?1 Fe₂O₃ and 160.2?g kg^?1 Al₂O₃) was the sample with the highest rate constant, indicating the adsorption sites are readily available. All the soils are rich in aluminum and iron oxides, explaining the Freundlich coefficients (K_F) between 642 and 1360?mg^1-1/n kg^?1 L^1/n, which are higher than most of the coefficients described for other soils around the world. The maximum desorption (15% of the adsorbed amount) was observed for the Oxisol. For the other soils, desorption ranged from 2 to 7%. These results suggest that the leaching of free glyphosate to nearby surface and groundwaters is unlikely unless excessive doses are used. The adsorption parameters are useful for managing the right doses applied to the crops, thus avoiding contamination of adjacent areas.     

荔枝皮对重金属Ni~(2+)的吸附性能

采用批量实验研究了荔枝皮对水中重金属Ni2+吸附的影响因素(如接触时间、pH和吸附剂量)、吸附等温线、吸附动力学和吸附热力学等,并讨论了其吸附机理。结果表明,未改性荔枝皮和改性荔枝皮对Ni2+的吸附平衡时间均为30min;最适pH为6.0~7.0;最佳吸附剂量均为20 g/L。吸附过程均能用Langmuir和Freundlich等温线模型来很好地描述,且均符合假二次动力学模型。改性荔枝皮和未改性荔枝皮对Ni2+的最大比吸附量分别为11.88和5.19 mg/g。此外,热力学研究结果表明,未改性荔枝皮和改性荔枝皮吸附Ni2+均属于非自发的放热过程。     

Adsorptive removal of an acid dye by lignocellulosic waste biomass activated carbon: equilibrium and kinetic studies

Chemically prepared activated carbon material derived from palm flower was used as adsorbent for removal of Amido Black dye in aqueous solution. Batch adsorption studies were performed for the removal of Amido Black 10B (AB10B), a di-azo acid dye from aqueous solutions by varying the parameters like initial solution pH, adsorbent dosage, initial dye concentration and temperature with three different particle sizes such as 100 μm, 600 μm and 1000 μm. The zero point charge was pH 2.5 and the maximum adsorption occurred at the pH 2.3. Experimental data were analyzed by model equations such as Langmuir, Freundlich and Temkin isotherms and it was found that the Freundlich isotherm model best fitted the adsorption data and the Freundlich constants varied from (K_F) 1.214, 1.077 and 0.884 for the three mesh sizes. Thermodynamic parameters such as ΔG, ΔH and ΔS were also calculated for the adsorption processes and found that the adsorption process is feasible and it was the endothermic reaction. Adsorption kinetics was determined using pseudo first-order, pseudo second-order rate equations and also Elovich model and intraparticle diffusion models. The results clearly showed that the adsorption of AB10B onto lignocellulosic waste biomass from palm flower (LCBPF) followed pseudo second-order model, and the pseudo second-order rate constants varied from 0.059 to 0.006 (g mg⁻¹ min) by varying initial adsorbate concentration from 25 mg L⁻¹ to 100 mg L⁻¹. Analysis of the adsorption data confirmed that the adsorption process not only followed intraparticle diffusion but also by the film diffusion mechanism.     

Adsorption of basic dyes onto MCM-41

The adsorption of two basic dyes, Basic Green 5 (BG5) and Basic Violet 10 (BV10), onto MCM-41 was studied to examine the possible effect of interactions between large adsorbates and MCM-41 on the pore structure stability of MCM-41 and the potential of MCM-41 for the removal of basic dyes from wastewater. The revolutions of surface characteristics and pore structure of MCM-41 induced by dyes adsorption were characterized based on the analyses of the nitrogen isotherms, the XRD patterns, and the FTIR spectra. It was experimentally concluded that when the effect of interactions between large dyes (such as BV10) and MCM-41 on the pore structure stability of MCM-41 was insignificant, MCM-41 might be a good adsorbent for the removal of basic dyes from wastewater. The adsorption of BV10 on MCM-41 with respect to contact time, pH, and temperature was then measured to provide more information about the adsorption characteristics of MCM-41. Both Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the pseudo-second-order kinetic model was used to describe the kinetic data, from which some adsorption thermodynamic parameters were also evaluated.     

Removal mechanisms and kinetics of trace tetracycline by two types of activated sludge treating freshwater sewage and saline sewage

Understanding the removal mechanisms and kinetics of trace tetracycline by activated sludge is critical to both evaluation of tetracycline elimination in sewage treatment plants and risk assessment/management of tetracycline released to soil environment due to the application of biosolids as fertilizer. Adsorption is found to be the primary removal mechanism while biodegradation, volatilization, and hydrolysis can be ignored in this study. Adsorption kinetics was well described by pseudo-second-order model. Faster adsorption rate (k ₂?=?2.04?×?10^?2?g?min^?1?μg^?1) and greater adsorption capacity (q _e?=?38.8 μg?g^?1) were found in activated sludge treating freshwater sewage. Different adsorption rate and adsorption capacity resulted from chemical properties of sewage matrix rather than activated sludge surface characteristics. The decrease of tetracycline adsorption in saline sewage was mainly due to Mg²⁺ which significantly reduced adsorption distribution coefficient (K _d) from 12,990?±?260 to 4,690?±?180 L?kg^?1. Species-specific adsorption distribution coefficients followed the order of $ K_{\mathrm{d}}^{{ + 00}} \gg K_{\mathrm{d}}^{{ + - 0}} > K_{\mathrm{d}}^{{ + - - }} $ . Contribution of zwitterionic tetracycline to the overall adsorption was >90 % in the actual pH range in aeration tank. Adsorption of tetracycline in a wide range of temperature (10 to 35 °C) followed the Freundlich adsorption isotherm well.     

Performance Evaluation of Waste Activated Carbon on Atrazine Removal from Contaminated Water

Abstract

In this study, the potential of spent activated carbon from water purifier (Aqua Guard, India) for the removal of atrazine (2 chloro-4 ethylamino-6-isopropylamino-1, 3, 5 triazine) from wastewaters was evaluated. Different grades of spent activated carbon were prepared by various pretreatments. Based on kinetic and equilibrium study results, spent activated carbon with a grain size of 0.3–0.5 mm and washed with distilled water (designated as WAC) was selected for fixed column studies. Batch adsorption equilibrium data followed both Freundlich and Langmuir isotherm. Fixed bed adsorption column with spent activated carbon as adsorbent was used as a polishing unit for the removal of atrazine from the effluent of an upflow anaerobic sludge blanket (UASB) reactor treating atrazine bearing domestic wastewater. Growth of bacteria on the surface of WAC was observed during column study and bacterial activity enhanced the effectiveness of adsorbent on atrazine removal from wastewater.     

弱碱性树脂吸附-解吸苦味酸

考察了水中苦味酸在弱碱性离子交换树脂D301R上的吸附与解吸。研究了吸附热力学、动力学特性及吸附机理。结果表明,树脂在pH=2.7～10.2时,吸附能力最好。等温平衡吸附遵循Freundlich模型。吸附过程为吸热、熵增的自发过程。吸附动力学符合Lagergren准二级速率方程,颗粒内扩散为吸附速率的主要控制步骤,吸附速率常数为7.23×10-5～1.20×10-4g/(mg.min),吸附活化能为19.4 kJ/mol。树脂上吸附的苦味酸可用HNO3+丙酮混合液定量洗脱,洗脱率达99%。静态吸附和脱附的比较结果证实了吸附过程中存在不可逆化学吸附。树脂对苦味酸的吸附主要是通过静电吸附、酸碱络合吸附、氢键吸附等协同作用来完成的。     

活化赤泥的除氟性能

以成本低的铝工业废矿渣（赤泥）为原材料,通过高温煅烧和酸化处理对赤泥进行活化,制备了除氟吸附剂。研究了反应时间、投加量、初始氟浓度、溶液温度、共存阴离子和pH值对活化赤泥除氟效果的影响。结果表明,接触反应时间为18 h时,吸附接近平衡。活化赤泥对氟离子的吸附符合Lagergren二级吸附动力学方程。另外,初始浓度越高,吸附容量越大。与Freundlich相比,Langmuir吸附等温模型可以更好地描述氟离子的吸附特性,最大吸附量可达2.71 mg/g。SO24-、Cl-和NO3-存在时（〈1 000 mg/L）,对氟离子的吸附几乎没有影响,然而,HCO3-、PO34-和氟离子共存时,会对氟吸附造成不利影响。活化赤泥在pH值3.5～11.0时,具有较好的吸附稳定性。活化赤泥是一种吸附容量高、性能稳定的环境友好型除氟材料,具有应用潜力。