Influences of thermal decontamination on mercury removal, soil properties, and repartitioning of coexisting heavy metals

Thermal treatment is a useful tool to remove Hg from contaminated soils. However, thermal treatment may greatly alter the soil properties and cause the coexisting contaminants, especially trace metals, to transform and repartition. The metal repartitioning may increase the difficulty in the subsequent process of a treatment train approach. In this study, three Hg-contaminated soils were thermally treated to evaluate the effects of treating temperature and duration on Hg removal. Thermogravimetric analysis was performed to project the suitable heating parameters for subsequent bench-scale fixed-bed operation. Results showed that thermal decontamination at temperature >400 °C successfully lowered the Hg content to <20 mg kg⁻¹. The organic carbon content decreased by 0.06-0.11% and the change in soil particle size was less significant, even when the soils were thermally treated to 550 °C. Soil clay minerals such as kaolinite were shown to be decomposed. Aggregates were observed on the surface of soil particles after the treatment. The heavy metals tended to transform into acid-extractable, organic-matter bound, and residual forms from the Fe/Mn oxide bound form. These results suggest that thermal treatment may markedly influence the effectiveness of subsequent decontamination methods, such as acid washing or solvent extraction.     

EDTA强化电动力学修复重金属复合污染土壤

在自制的电动力学装置中,研究多种重金属复合污染土壤的电动力学修复,通过在阴极添加络合剂EDTA来提高修复效率。实验结果表明,EDTA的引入提高了修复过程中的电流值,且EDTA与重金属的络合提高了污染物向电极液的迁移效率,从而强化了电动力学修复效果。在设定的浓度(0、0.01、0.02、0.05和0.1 mol/L)中,0.1 mol/L的EDTA具有最佳的修复效率。在此实验条件下,污染土壤中的总铜、总铅和总镉的去除率分别为90.2%、68.1%和95.1%。电动力学修复后,对土壤重金属进行化学形态分析,发现电动力学修复显著改变了土壤重金属存在形态,修复后土壤中的铜、铅、镉主要以较稳定的有机态和残余态形式存在,显著降低了对周边生物和环境的毒害。     

EDTA及其回收溶液治理重金属污染土壤的研究

试验结果表明,EDTA能够有效地萃取土壤重金属,由于其价格较贵和不易被降解等特点,限制了它的广泛运用.在运用MINTEQA2模型对萃取液中重金属离子形态分析的基础上,选用Na2S沉淀法将重金属从EDTA萃取液中有效分离.同时将回收的EDTA连续进行萃取土壤重金属,由于回收EDTA浓度下降的原因,其效果比新鲜EDTA的要稍微差一点,但从经济和效率上来说,仍旧可以用来治理重金属污染的土壤.     

Using biochar for remediation of soils contaminated with heavy metals and organic pollutants

Soil contamination with heavy metals and organic pollutants has increasingly become a serious global environmental issue in recent years. Considerable efforts have been made to remediate contaminated soils. Biochar has a large surface area, and high capacity to adsorb heavy metals and organic pollutants. Biochar can potentially be used to reduce the bioavailability and leachability of heavy metals and organic pollutants in soils through adsorption and other physicochemical reactions. Biochar is typically an alkaline material which can increase soil pH and contribute to stabilization of heavy metals. Application of biochar for remediation of contaminated soils may provide a new solution to the soil pollution problem. This paper provides an overview on the impact of biochar on the environmental fate and mobility of heavy metals and organic pollutants in contaminated soils and its implication for remediation of contaminated soils. Further research directions are identified to ensure a safe and sustainable use of biochar as a soil amendment for remediation of contaminated soils.     

Scavenging of BHCs and DDTs from soil by thermal desorption and solvent washing

Intensive remediation of abandoned former organochlorine pesticides (OCPs) manufacturing areas is necessary because the central and surrounding soils contaminated by OCPs are harmful to crop production and food safety. Organochlorine and its residues are persistent in environments and difficult to remove from contaminated soils due to their low solubility and higher sorption to the soils. We performed a comprehensive study on the remediation of OCPs-contaminated soils using thermal desorption technique and solvent washing approaches. The tested soil was thermally treated at 225, 325, 400, and 500 °C for 10, 20, 30, 45, 60, and 90 min, respectively. In addition, we tested soil washing with several organic solvents including n-alcohols and surfactants. The optimal ratio of soil/solvent was tested, and the recycling of used ethanol was investigated. Finally, activities of polyphenol oxidase (PPO), urease (URE), alkaline phosphatase, acid phosphatase (ACP), and invertase (INV) were assayed in the treated soils. The tested soil was thermally treated at 500 °C for 30 min, and the concentration of contaminants in soil was decreased from 3,115.77 to 0.33 mg kg^?1. The thermal desorption in soil was governed by the first-order kinetics model. For the chemical washing experiment, ethanol showed a higher efficiency than any other solvent. Using a 1:20 ratio of soil/solvent, the maximum removal of OCPs was achieved within 15 min. Under this condition, approximately 87 % of OCPs was removed from the soils. More than 90 % of ethanol in the spent wash fluid could be recovered. Activities of some enzymes in soils were increased after ethanol treatment. But ALP, ACP, and INV activities were decreased and PPO and URE showed slightly higher activities following remediation by thermal treatment. Both heating temperature and time were the key factors for thermal desorption of OCPs. The n-alcohol solvent showed higher removal of OCPs from soils than surfactants. The highly efficient removal of OCPs from soil was achieved using ethanol. More than 90 % of ethanol could be recovered and be reused following distillation. This study provides a cost-effective and highly efficient way to remediate the OCPs-contaminated soils.     

Zinc tolerance and uptake by <Emphasis Type="Italic">Arabidopsis halleri ssp. gemmifera</Emphasis> grown in nutrient solution

Background, aim, and scope  

Zinc is an essential micronutrient element but its concentrations found in contaminated soils frequently exceed those required by the plant and soil organisms, and thus create danger to animal and human health. Phytoremediation is a technique, often employed in remediation of contaminated soils, which aims to remove heavy metals or other contaminants from soils or waters using plants. Arabidopsis (A.) halleri ssp. gemmifera is a plant recently found to be grown vigorously in heavy metal contaminated areas of Japan and it contained remarkably high amount of heavy metals in its shoots. However, the magnitude of Zn accumulation and tolerance in A. halleri ssp. gemmifera need to be investigated for its use as a phytoremediation plant.     

Soil remediation: humic acids as natural surfactants in the washings of highly contaminated soils

The remediation of the highly contaminated site around the former chemical plant of ACNA (near Savona) in Northern Italy is a top priority in Italy. The aim of the present work was to contribute in finding innovative and environmental-friendly technology to remediate soils from the ACNA contaminated site. Two soils sampled from the ACNA site (A and B), differing in texture and amount and type of organic contaminants, were subjected to soil washings by comparing the removal efficiency of water, two synthetic surfactants, sodium dodecylsulphate (SDS) and Triton X-100 (TX100), and a solution of a natural surfactant, a humic acid (HA) at its critical micelle concentration (CMC). The extraction of pollutants by sonication and soxhlet was conducted before and after the soil washings. Soil A was richer in polycyclic aromatic hydrocarbons, whereas soil B had a larger content of thiophenes. Sonication resulted more analytically efficient in the fine-textured soil B. The coarse-textured soil A was extracted with a general equal efficiency also by soxhlet. Clean-up by water was unable to exhaustively remove contaminants from the two soils, whereas all the organic surfactants revealed very similar efficiencies (up to 90%) in the removal of the contaminants from the soils. Hence, the use of solutions of natural HAs appears as a better choice for soil washings of highly polluted soils due to their additional capacity to promote microbial activity, in contrast to synthetic surfactants, for a further natural attenuation in washed soils.     

Bioaccumulation in Porcellio scaber (Crustacea, Isopoda) as a measure of the EDTA remediation efficiency of metal-polluted soil

Leaching using EDTA applied to a Pb, Zn and Cd polluted soil significantly reduced soil metal concentrations and the pool of metals in labile soil fractions. Metal mobility (Toxicity Characteristic Leaching Procedure), phytoavailability (diethylenetriaminepentaacetic acid extraction) and human oral-bioavailability (Physiologically Based Extraction Test) were reduced by 85-92%, 68-91% and 88-95%, respectively. The metal accumulation capacity of the terrestrial isopod Porcellio scaber (Crustacea) was used as in vivo assay of metal bioavailability, before and after soil remediation. After feeding on metal contaminated soil for two weeks, P. scaber accumulated Pb, Zn and Cd in a concentration dependent manner. The amounts of accumulated metals were, however, higher than expected on the basis of extraction (in vitro) tests. The combined results of chemical extractions and the in vivo test with P. scaber provide a more relevant picture of the availability stripping of metals after soil remediation.     

Effect of temperature and particle size on the thermal desorption of PCBs from contaminated soil

Thermal desorption is widely used for remediation of soil contaminated with volatiles, such as solvents and distillates. In this study, a soil contaminated with semivolatile polychlorinated biphenyls (PCBs) was sampled at an interim storage point for waste PCB transformers and heated to temperatures from 300 to 600 °C in a flow of nitrogen to investigate the effect of temperature and particle size on thermal desorption. Two size fractions were tested: coarse soil of 420–841 μm and fine soil with particles <250 μm. A PCB removal efficiency of 98.0 % was attained after 1 h of thermal treatment at 600 °C. The residual amount of PCBs in this soil decreased with rising thermal treatment temperature while the amount transferred to the gas phase increased up to 550 °C; at 600 °C, destruction of PCBs became more obvious. At low temperature, the thermally treated soil still had a similar PCB homologue distribution as raw soil, indicating thermal desorption as a main mechanism in removal. Dechlorination and decomposition increasingly occurred at high temperature, since shifts in average chlorination level were observed, from 3.34 in the raw soil to 2.75 in soil treated at 600 °C. Fine soil particles showed higher removal efficiency and destruction efficiency than coarse particles, suggesting that desorption from coarse particles is influenced by mass transfer.     

Washing as a remediation technology applicable in soils heavily polluted by mining-metallurgical activities

A permanent solution in order to remediate a heavily contaminated soil is washing it utilizing the appropriate reagents. The study presented in this paper deals with the washing of a soil highly polluted by mining and metallurgical activities. Pollution consists of slags, sulphur compound waste and various low grade lead condensates, all rich in heavy metals and metalloids (Pb, As, Cu, Zn, Mn and Fe). Soil was washed with deionized water, 6, 3, 2 and 1 M HCl, 6 M H(2)SO(4), 6 M HNO(3) and 0.1 M Na(2)EDTA. High extraction efficiency was achieved with respect to hydrochloric acid even at the lowest concentration; the solubility of pollutants in nitric acid was low, while sulphuric acid was proven to be problematic with respect to lead. Mobilization of metals and metalloids under DI water effect was minimal indicating that the elements fraction that is weakly bound to soil particles is insignificant. Furthermore, a kinetic study was undertaken, utilizing 1 M HCl and 0.1 M Na(2)EDTA. Results illustrated that 1 M HCl was more effective for intermediate mixing times (up to 4 h) while 0.1 M Na(2)EDTA was better applicable to short mixing times (<1 h) and low pH values (pH < 7.1). 1 M HCl was proven to be very effective for the removal of pollutants from contaminated soil but the high metal content of the resulting solution necessitates further treatment for the retention of metals.     

Removal of heavy metals and arsenic from contaminated soils using bioremediation and chelant extraction techniques

A combined chemical and biological treatment scheme was evaluated in this study aiming at obtaining the simultaneous removal of metalloid arsenic and cationic heavy metals from contaminated soils. The treatment involved the use of the iron reducing microorganism Desulfuromonas palmitatis, whose activity was combined with the chelating strength of EDTA. Taking into consideration that soil iron oxides are the main scavengers of As, treatment with iron reducing microorganisms aimed at inducing the reductive dissolution of soil oxides and thus obtaining the release of the retained As. The main objective of using EDTA was the removal of metal contaminants, such as Pb and Zn, through the formation of soluble metal chelates. Experimental results however indicated that EDTA was also indispensable for the biological reduction of Fe(III) oxides. The bacterial activity was found to have a pronounced positive effect on the removal of arsenic, which increased from the value of 35% obtained during the pure chemical treatment up to 90% in the presence of D. palmitatis. In the case of Pb, the major part, i.e. approximately 85%, was removed from soil with purely chemical mechanisms, whereas the biological activity slightly improved the extraction, increasing the final removal up to 90%. Co-treatment had negative effect only for Zn, whose removal was reduced from 80% under abiotic condition to approximately 50% in the presence of bacteria.     

Process evaluation for optimization of EDTA use and recovery for heavy metal removal from a contaminated soil

This study aimed to establish an optimized, closed loop application of ethylenediaminetetraacetic acid (EDTA) in heavy metal removals from a contaminated soil through integrating EDTA recovery/regeneration and metal precipitation processes in the treatment train. Three divalent heavy metals were investigated, namely, Pb, Cd, and Ni. The extractability of the metals by EDTA followed the decreasing order of CdPb>Ni. The first part of this study was to search for the optimal use of the fresh EDTA in removing these heavy metals from the contaminated soil. The second part of this study was devoted to the recovery/regeneration of the spent EDTA which followed the sequential processes involving (1) complex destabilization by adding ferric ion (Fe(III)) to liberate Pb, Cd, and Ni, (2) precipitation of the liberated Pb, Cd, and Ni in phosphate (PO4(3-)) forms, and (3) precipitation of the excess Fe(III) which eventually produced free EDTA for reuse. The process variables were dosages of Fe(III) and PO4(3-), pH and reaction times. Laborious trial experiments would be needed in searching for the optimum conditions for the above processes. To expedite this exercise, a geochemical equilibrium model, MINTEQA2, was used to find the thermodynamically favorable conditions for recoveries of both EDTA and heavy metals. This was then followed by experimental examination of the process kinetics to observe for the optimal reaction time for each thermodynamically favorable process. This study revealed that 2 h of reaction time each for the complex destabilization reaction and the metal phosphate precipitation reaction was sufficient to achieve equilibrium. With the optimized process condition identified in this study, a total of 95%, 89% and 90% of the extracted Pb, Cd and Ni, respectively, could be precipitated from the spent EDTA solution, with 84% EDTA recovery. The reused EDTA maintained more than 90% of its preceding extraction power in each cycle of reuse.     

The use of maize and poplar in chelant-enhanced phytoextraction of lead from contaminated agricultural soils

Chelant-enhanced phytoextraction of heavy metals is an emerging technological approach for a non-destructive remediation of contaminated soils. The main objectives of this study were (i) to assess the extraction efficiency of two different synthetic chelating agents (ethylenediaminetetraacetic acid (EDTA) and ethylenediaminedisuccinic acid (EDDS)) for desorbing Pb from two contaminated agricultural soils originating from a mining and smelting district and (ii) to assess the phytoextraction efficiency of maize (Zea mays) and poplar (Populus sp.) after EDTA application. EDTA was more efficient than EDDS in desorbing and complexing Pb from both soils, removing as much as 60% of Pb. Maize exhibited better results than poplar when extracting Pb from the more acidic (pH approximately 4) and more contaminated (up to 1360 mg Pb kg(-1)) agricultural soil originating from the smelting area. On the other hand, poplars proved to be more efficient when grown on the near-neutral (pH approximately 6) and less contaminated (up to 200 mg Pb kg(-1)) agricultural soil originating from the mining area. Furthermore, the addition of EDTA led to a significant increase of Pb content especially in poplar leaves, proving a strong translocation rate within the poplar plants.     

Evaluation of the effect of small organic acids on phytoextraction of Cu and Pb from soil with tobacco Nicotiana tabacum

Phytoremediation, the use of plants to extract contaminants from soils and groundwater, is a promising approach for cleaning up soils contaminated with heavy metals. However its use is limited by the time required for plant growth, the nutrient supply and, moreover, by the limited metal uptake capacity. Synthetic chelators have shown positive effects in enhancing heavy metal extraction, but they have also revealed several negative side-effects. The objective of this study was to investigate the use of three natural low molecular weight organic acids (NLMWOA) (citric, oxalic, and tartaric acid) as an alternative to synthetic chelators. Slurry-, column-, toxicity- and phytoextraction experiments were performed. For the phytoextraction experiment the three NLMWOA were applied to a copper- and a lead-contaminated soil respectively. A significant increase in copper uptake was visible only in the citric acid treatment (67 mg kg-1) in comparison to the EDTA treatment (42 mg kg-1). The NLMWOA application showed no enhanced effect concerning the lead phytoextraction. A possible explanation for this lack of significance could be the rate of the degradation of NLMWOA. This rate might well be too high for these heavy metals with low mobility and bioavailability such as lead. The amounts of NLMWOA applied to the soil were very high (62.5 mmol kg-1 of soil) and the effect was too little. In this respect EDTA, which was applied in very small amounts (0.125 mmol kg-1) was more efficient. Thus making NLMWOA unsuitable to enhance phytoextraction of heavy metals from soil.     

功能微生物对污染农田土壤中铅锌的溶出实验

用微生物修复重金属污染的土壤是当今的研究热点之一。试图寻找一类可以增加土壤中重金属铅、锌的可溶态的功能微生物,并研究该微生物在不同土壤含水率和不同投菌比条件下对铅、锌溶出作用的影响。最终筛选出符合条件的菌JK3,并发现当土壤含水率为35%,投菌比为0.15 mL/g土(菌液OD=1)时,土壤中铅和锌的可溶态增加量最多。其中,可溶态铅的含量由原来的0.49 mg/kg增加到了5.04 mg/kg,可溶态锌的含量由原来的2.23 mg/kg增加到了22.44mg/kg。该方法为后续用植物提取或化学淋洗等方法将土壤中的重金属彻底去除提供了可能。     

Combined chemical and biological treatment of oil contaminated soil

Combined chemical (Fenton-like and ozonation) and biological treatment for the remediation of shale oil and transformer oil contaminated soil has been under study. Chemical treatment of shale oil and transformer oil adsorbed in peat resulted in lower contaminants' removal and required higher addition of chemicals than chemical treatment of contaminants in sand matrix. The acidic pH (3.0) conditions favoured Fenton-like oxidation of oil in soil. Nevertheless, it was concluded that remediation of contaminated soil using in situ Fenton-like treatment will be more feasible at natural soil pH. Both investigated chemical processes (Fenton-like and ozonation) allowed improving the subsequent biodegradability of oil. Moderate doses of chemical oxidants (hydrogen peroxide, ozone) should be applied in combination of chemical treatment (both, Fenton-like or ozonation) and biotreatment. For remediation of transformer oil and shale oil contaminated soil Fenton-like pre-treatment followed by biodegradation was found to be the most efficient.     

Biochar- and phosphate-induced immobilization of heavy metals in contaminated soil and water: implication on simultaneous remediation of contaminated soil and groundwater

Long-term wastewater irrigation or solid waste disposal has resulted in the heavy metal contamination in both soil and groundwater. It is often separately implemented for remediation of contaminated soil or groundwater at a specific site. The main objective of this study was to demonstrate the hypothesis of simultaneous remediation of both heavy metal contaminated soil and groundwater by integrating the chemical immobilization and pump-and-treat methods. To accomplish the objective, three experiments were conducted, i.e., an incubation experiment was first conducted to determine how dairy-manure-derived biochar and phosphate rock tailing induced immobilization of Cd in the Cd-contaminated soils; second, a batch sorption experiment was carried out to determine whether the pre-amended contaminated soil still had the ability to retain Pb, Zn and Cd from aqueous solution. BCR sequential extraction as well as XRD and SEM analysis were conducted to explore the possible retention mechanism; and last, a laboratory-scale model test was undertaken by leaching the Pb, Zn, and Cd contaminated groundwater through the pre-amended contaminated soils to demonstrate how the heavy metals in both contaminated soil and groundwater were simultaneously retained and immobilized. The incubation experiment showed that the phosphate biochar were effective in immobilizing soil Cd with Cd concentration in TCLP (toxicity characteristics leaching procedure) extract reduced by 19.6 % and 13.7 %, respectively. The batch sorption experiment revealed that the pre-amended soil still had ability to retain Pb, Zn, and Cd from aqueous solution. The phosphate-induced metal retention was mainly due to the metal–phosphate precipitation, while both sorption and precipitation were responsible for the metal stabilization in the biochar amendment. The laboratory-scale test demonstrated that the soil amended with phosphate removed groundwater Pb, Zn, and Cd by 96.4 %, 44.6 %, and 49.2 %, respectively, and the soil amended with biochar removed groundwater Pb, Zn, and Cd by 97.4 %, 53.4 %, and 54.5 %, respectively. Meanwhile, the metals from both groundwater and soil itself were immobilized with the amendments, with the leachability of the three metals in the CaCl₂ and TCLP extracts being reduced by up to 98.1 % and 62.7 %, respectively. Our results indicate that the integrated chemical immobilization and pump-and-treat method developed in this study provides a novel way for simultaneous remediation of both metal-contaminated soil and groundwater.     

Electrochemical EDTA recycling with sacrificial Al anode for remediation of Pb contaminated soil

Recycling chelant is a precondition for cost-effective EDTA-based soil remediation. Extraction with EDTA removed 67.5% of Pb from the contaminated soil and yielded washing solution with 1535 mg L⁻¹ Pb and 33.4 mM EDTA. Electrochemical treatment of the washing solution using Al anode, current density 96 mA cm⁻² and pH 10 removed 90% of Pb from the solution (by electrodeposition on the stainless steel cathode) while the concentration of EDTA in the treated solution remained the same. The obtained data indicate that the Pb in the EDTA complex was replaced by electro-corroded Al after electro-reduction of the EDTA and subsequently removed from the solution. Additional soil extraction with the treated washing solution resulted in total removal of 87% of Pb from the contaminated soil. The recycled EDTA retained the Pb extraction potential through several steps of soil extraction and washing solution treatment, although part of the EDTA was lost by soil absorption.     

Role of plants, mycorrhizae and phytochelators in heavy metal contaminated land remediation

Phytoremediation is a site remediation strategy, which employs plants to remove non-volatile and immisible soil contents. This sustainable and inexpensive process is emerging as a viable alternative to traditional contaminated land remediation methods. To enhance phytoremediation as a viable strategy, fast growing plants with high metal uptake ability and rapid biomass gain are needed. This paper provides a brief review of studies in the area of phytoaccumulation, most of which have been carried out in Europe and the USA. Particular attention is given to the role of phytochelators in making the heavy metals bio-available to the plant and their symbionts in enhancing the uptake of bio-available heavy metals.     

粘土矿物修复重金属污染土壤

简要介绍了我国土壤重金属污染的现状与危害.通过粘土矿物在重金属污染土壤中净化功能的阐述,提出利用粘土矿物修复土壤重金属污染的观点.继而从天然和改性粘土矿物特性,叙述了粘土矿物修复土壤重金属污染的机制与应用进展及其影响因素.最后讨论了粘土矿物在修复土壤重金属污染过程中值得注意的几个问题,并展望了粘土矿物在该领域应用中的发展方向.