Modeling and model performance evaluation of sewage sludge gasification in fluidized-bed gasifiers using Aspen Plus

A model was developed to simulate the sewage sludge gasification in an atmospheric fluidised bed gasifier using Aspen Plus. The model here presented was based on the Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it against previously published experimental data obtained in a lab-scale gasification plant. A sensitivity analysis of the model was carried out by modifying parameters such as the temperature, equivalence ratio (ER) and the steam-to-biomass ratio. The modeled results were in good agreement with the experimental data (especially when air was used as gasifying agent) and reproduced satisfactorily the experimental trends found for the gas composition, the carbon conversion (Xc) and the cold gas efficiency (CGE) under different gasification conditions. Operating at higher temperatures increased the production of H₂ and CO, as well as the Xc and the CGE. The increase in ER produced higher Xc, yet the CGE experienced slight changes due to a decrease in the lower heating value of the resulting syngas, as well as the oxidation of combustible gases. The use of air+steam as gasifying agent increased the H₂ content of the produced gases but decreased the accuracy of the model.

Implications: Gasification is an available alternative to produce energy as well as several raw materials from sewage sludge. The syngas obtained from this technology totally depends on the type of gasifier and the operation conditions, which can be optimized with the help of models. In this work, a relatively simple model was built using ASPEN PLUS. Despite its simplicity, the outputs of the model are in good agreement with experimental results what makes its use interesting for assessing scaling-up possibilities from lab-scale to pilot-scale gasification processes.     

Gas reforming and tar decomposition performance of nickel oxide (NiO)/SBA-15 catalyst in gasification of woody biomass

In the gasification of biomass, it is necessary to limit the amount of by-product tar and increase the yields of hydrogen (H₂) and carbon monoxide (CO) (syngas). Therefore, we conducted gasification and reforming experiments on woody biomass using an electric tubular furnace, to evaluate the gas reforming and tar decomposition performance of a NiO/SBA-15 catalyst. As a result, we found that this catalyst is effective for H₂ production. It is believed that the increase in H₂ volume due to the catalyst occurs through a steam reforming reaction involving hydrocarbons, including methane (CH₄), and the water-gas shift reaction. With respect to the influence of the gasifying agent on the reforming effect of the catalyst, the amount of generated carbon dioxide (CO₂) and hydrogen (H₂) increases because the shift reaction is promoted by supplying steam. On the other hand, it was inferred that the shift reaction rarely occurred because it approaches equilibrium by supplying O₂. Furthermore, it is suggested that light aromatic hydrocarbons are decomposed by the catalyst.

Implications: The mesoporous silica catalyst NiO/SBA-15 was highly effective for H₂ production and decomposition of light aromatic compounds in the gasification of woody biomass. In the catalyst reaction, supplying steam promoted H₂ production. From thermodynamic analysis and discussion, it was also inferred that supplying O₂ might prevent the water gas shift reaction. The results are useful for designing a process needed for rich H₂ production and gas refining process for further use of syngas.     

Wastewater and sludge management and research in Oman: An overview

It is well recognized that management of wastewater and sludge is a critical environmental issue in many countries. Wastewater treatment and sludge production take place under different technical, economic, and social contexts, thus requiring different approaches and involving different solutions. In most cases, a regular and environmentally safe wastewater treatment and associated sludge management requires the development of realistic and enforceable regulations, as well as treatment systems appropriate to local circumstances. The main objective of this paper is to provide useful information about the current wastewater and sludge treatment, management, regulations, and research in Oman. Based on the review and discussion, the wastewater treatment and sludge management in Oman has been evolving over the years. Further, the land application of sewage sludge should encourage revision of existing standards, regulations, and policies for the management and beneficial use of sewage sludge in Oman.

Implications: Wastewater treatment and sludge management in Oman have been evolving over the years. Sludge utilization has been a challenge due to its association with human waste. Therefore, composting of sewage sludge is the best option in agriculture activities. Sludge and wastewater utilization can add up positively in the economic aspects of the country in terms of creating jobs and improving annual income rate. The number of research projects done on wastewater reuse and other ongoing ones related to the land application of sewage sludge should encourage revision of existing standards, regulations, and policies for the management and beneficial use of sewage sludge in Oman.     

Effect of potassium hydroxide activation in the desulfurization process of activated carbon prepared by sewage sludge and corn straw

Series sludge straw–based activated carbons were prepared by sewage sludge and corn straw with potassium hydroxide (KOH) activation, and the desulfurization performance of activated carbons was studied. To obtain the best desulfurization performance, the optimum ratio between the raw materials and the activator was investigated. The results showed that when the mass ratio of sewage sludge, corn straw, and KOH was 3:7:2, the activated carbon obtained the best breakthrough and saturation sulfur sorption capacities, which were 12.38 and 5.74 times, respectively, those of samples prepared by the nonactivated raw materials. The appropriate KOH could improve the microporosity and alkaline groups, meanwhile reducing the lactone groups, which were all beneficial to desulfurization performance. The chemical adsorption process of desulfurization can be simplified to four main steps, and the main desulfurization products are elemental sulfur and sulfate.

Implications: Sewage sludge (SS) and corn straw (CS) both have great production and wide distribution and are readily available in China. Much attention has been paid on how to deal with them effectively. Based on the environment protection idea of waste treatment with waste and resource recycling, low-cost adsorbents were prepared by these processes. The proposed method can be expanded to the municipal solid waste recycling programs and renewable energy plan. Thus, proceeding with the study of preparing activated carbon by SS and straw as a carbon-based dry desulfurization agent could obtain huge social, economic, and environmental benefits.     

Application of magnetically modified sewage sludge ash (SSA) in ionic dye adsorption

Incineration is a traditional method of treating sewage sludge and the disposal of derived ash is a problem of secondary waste treatment. In this study, sewage sludge ash (SSA) was coated with ferrite through a ferrite process and then used as an adsorbent for ionic dyes (methylene blue [MB] and Procion Red MX-5B [PR]). The modified SSA possessed surface potential that provided electrostatic attraction toward MB and PR. Adsorbent FA10 (named on the basis of being produced from 10 g of SSA in the ferrite process) was used for the adsorption of MB. Ideal pH for adsorption was 9.0 and maximum adsorption capacity based on Langmuir isotherm equation was 22.03 mg/g. Adsorbent FA2.5 (named on the basis of being produced from 2.5 g of SSA in the ferrite process) was used for PR adsorption. Ideal pH for adsorption was 3.0 and the maximum adsorption capacity (calculated as above) was 28.82 mg/g. Kinetic results reveal that both MB and PR adsorption fit the pseudo-second-order kinetic model better than the pseudo-first-order model. The values of activation energy calculated from rate constants were 61.71 and 9.07 kJ/mol for MB and PR, respectively.

Implications:

Magnetic modified adsorbent could be synthesized from sewage sludge ash (SSA). In this study, the adsorption ability of SSA toward ionic dye (methylene blue [MB] and Procion Red MX-5B [PR]) was enhanced by ferrite process. The synthesized Fe₃O₄ can act as an active site and provide electrostatic attraction toward cationic dye and anionic dye at different pH. The application of magnetic modified adsorbent in wastewater treatment can not only recycle the SSA, but also make SSA become an environmentally friendly material.     

Biogas production from anaerobic digestion of food waste and relevant air quality implications

Biopower can diversify energy supply and improve energy resiliency. Increases in biopower production from sustainable biomass can provide many economic and environmental benefits. For example, increasing biogas production through anaerobic digestion of food waste would increase the use of renewable fuels throughout California and add to its renewables portfolio. Although a biopower project will produce renewable energy, the process of producing bioenergy should harmonize with the goal of protecting public health. Meeting air emission requirements is paramount to the successful implementation of any biopower project. A case study was conducted by collecting field data from a wastewater treatment plant that employs anaerobic codigestion of fats, oils, and grease (FOG), food waste, and wastewater sludge, and also uses an internal combustion (IC) engine to generate biopower using the biogas. This research project generated scientific information on (a) quality and quantity of biogas from anaerobic codigestion of food waste and municipal wastewater sludge, (b) levels of contaminants in raw biogas that may affect beneficial uses of the biogas, (c) removal of the contaminants by the biogas conditioning systems, (d) emissions of NO_x, SO₂, CO, CO₂, and methane, and (e) types and levels of air toxics present in the exhausts of the IC engine fueled by the biogas. The information is valuable to those who consider similar operations (i.e., co-digestion of food waste with municipal wastewater sludge and power generation using the produced biogas) and to support rulemaking decisions with regards to air quality issues for such applications.

Implications: Full-scale operation of anaerobic codigestion of food waste with municipal sludge is viable, but it is still new. There is a lack of readily available scientific information on the quality of raw biogas, as well as on potential emissions from power generation using this biogas. This research developed scientific information with regard to quality and quantity of biogas from anaerobic co-digestion of food waste and municipal wastewater sludge, as well as impacts on air quality from biopower generation using this biogas. The need and performance of conditioning/pretreatment systems for biopower generation were also assessed.     

Adsorption of mercury by activated carbon prepared from dried sewage sludge in simulated flue gas

Conversion of sewage sludge to activated carbon is attractive as an alternative method to ocean dumping for the disposal of sewage sludge. Injection of activated carbon upstream of particulate matter control devices has been suggested as a method to remove elemental mercury from flue gas. Activated carbon was prepared using various activation temperatures and times and was tested for their mercury adsorption efficiency using lab-scale systems. To understand the effect of the physical property of the activated carbon, its mercury adsorption efficiency was investigated as a function of its Brunauer–Emmett–Teller (BET) surface area. Two simulated flue gas conditions, (1) without hydrogen chloride (HCl) and (2) with 20 ppm HCl, were used to investigate the effect of flue gas composition on the mercury adsorption capacity of activated carbon. Despite very low BET surface area of the prepared sewage sludge activated carbons, their mercury adsorption efficiencies were comparable under both simulated flue gas conditions to those of pinewood and coal activated carbons. After injecting HCl into the simulated flue gas, all sewage sludge activated carbons demonstrated high adsorption efficiencies, that is, more than 87%, regardless of their BET surface area.

Implications: We tested activated carbons prepared from dried sewage sludge to investigate the effect of their physical properties on their mercury adsorption efficiency. Using two simulated flue gas conditions, we conducted mercury speciation for the outlet gas. We found that the sewage sludge activated carbon had mercury adsorption efficiency comparable to pinewood and coal activated carbons, and the presence of HCl minimized the effect of physical property of the activated carbon on its mercury adsorption efficiency.     

The study on biomass fraction estimate methodology of municipal solid waste incinerator in Korea

In Korea, the amount of greenhouse gases released due to waste materials was 14,800,000 t CO₂eq in 2012, which increased from 5,000,000 t CO₂eq in 2010. This included the amount released due to incineration, which has gradually increased since 2010. Incineration was found to be the biggest contributor to greenhouse gases, with 7,400,000 t CO₂eq released in 2012. Therefore, with regards to the trading of greenhouse gases emissions initiated in 2015 and the writing of the national inventory report, it is important to increase the reliability of the measurements related to the incineration of waste materials.

This research explored methods for estimating the biomass fraction at Korean MSW incinerator facilities and compared the biomass fractions obtained with the different biomass fraction estimation methods. The biomass fraction was estimated by the method using default values of fossil carbon fraction suggested by IPCC, the method using the solid waste composition, and the method using incinerator flue gas.

The highest biomass fractions in Korean municipal solid waste incinerator facilities were estimated by the IPCC Default method, followed by the MSW analysis method and the Flue gas analysis method. Therefore, the difference in the biomass fraction estimate was the greatest between the IPCC Default and the Flue gas analysis methods. The difference between the MSW analysis and the flue gas analysis methods was smaller than the difference with IPCC Default method. This suggested that the use of the IPCC default method cannot reflect the characteristics of Korean waste incinerator facilities and Korean MSW.

Implications: Incineration is one of most effective methods for disposal of municipal solid waste (MSW). This paper investigates the applicability of using biomass content to estimate the amount of CO₂ released, and compares the biomass contents determined by different methods in order to establish a method for estimating biomass in the MSW incinerator facilities of Korea. After analyzing the biomass contents of the collected solid waste samples and the flue gas samples, the results were compared with the Intergovernmental Panel on Climate Change (IPCC) method, and it seems that to calculate the biomass fraction it is better to use the flue gas analysis method than the IPCC method. It is valuable to design and operate a real new incineration power plant, especially for the estimation of greenhouse gas emissions.     

Effects of earthworms and effective microorganisms on the composting of sewage sludge with cassava dregs in the tropics

The present study revealed the role of earthworm-effective microorganisms (EM) in converting sewage sludge and cassava dregs into a valuable product. Sewage sludge was toxic to earthworm, therefore it was mixed with cassava dregs in 80:20 proportions (dry weight). Treatments included mixed substrate inoculated versus not inoculated with EM and treated with or without earthworms. The pH, total organic carbon, total nitrogen, and C:N ratio decreased from the initial measurements in the range of 17.43–18.46%, 25.48–33.82%, 19.60–25.37%, and 6.68–14.05% respectively; but electrical conductivity and available phosphorus increased in the range of 113.47–158.16% and 42.42–57.58%, respectively. In addition, they interactively increased total phosphorus from 19.84–63.01% and potassium from 16.41–50.78%, and decreased the polycyclic aromatic hydrocarbons content of substrate from 21.17% to 32.14% with an increase in earthworms from 51.71 to 57.69, respectively. Earthworms and EM could be used together as an efficient method for co-composting sewage sludge plus cassava dregs in the tropics. This could be expected to result in stabilization of waste, increase in nutrients, and reduction of pollutant content.

Implications: The first reports of interaction of earthworms and effective microorganisms in the treatment of sewage sludge and cassava dregs in the tropics. Co-composting was an efficient technology for treating sewage sludge and cassava dregs at the same time, in the tropics. The survival rate of the earthworms both> 95%, the highest number of cocoons (640.33) and hatchlings (4694.33) both in EW+EM (Earthworms added and EM inoculated) treatment. Earthworms and EM (Only EM inoculated) interactively increased total phosphorus and potassium content, and decreased the PAH content of substrate with increase in earthworms.     

Bio-syngas production with low concentrations of CO2 and CH4 from microwave-induced pyrolysis of wet and dried sewage sludge

This paper assesses the feasibility of producing syngas from sewage sludge via two pyrolysis processes: microwave-induced pyrolysis (MWP) and conventional pyrolysis (CP). The changes in the composition of the produced gas as a function of the pyrolysis treatment and the initial moisture content of the sludge were evaluated. It was found that MWP produced a gas with a higher concentration of syngas than CP, reaching values of up to 94vol%. Moreover, this gas showed a CO2 and CH4 concentration around 50% and 70%, respectively, lower than that obtained in the gas from CP. With respect to the effect of moisture on gas composition, this was more pronounced in CP than in MWP. Thus, the presence of moisture increases the concentration of H2 and CO2 and decreases that of CO, especially when CP was used. In order to elucidate the behaviour of CO2 during the pyrolysis, the CO2 gasification kinetics of the char obtained from the pyrolysis were investigated. It was established that in microwave heating the gasification reaction is much more favoured than in conventional heating. Therefore, the low concentration of CO2 and the high concentration of CO in the microwave pyrolysis gas could be due to the self-gasification of the residue by the CO2 produced during the devolatilization of the sewage sludge in the pyrolysis process.     

Characterization of temporal variations in landfill gas components inside an open solid waste dump site in Sri Lanka

A long-term monitoring of composition of landfill gases in the region with high rainfall was conducted using an argon assay in order to discuss air intrusion into the dump site. Gas samples were taken from vertical gas monitoring pipes installed along transects at two sections (called new and old) of an abandoned waste dump site in Sri Lanka. N₂O concentrations varied especially widely, by more than three orders of magnitude (0.046–140 ppmv). The nitrogen/argon ratio of landfill gas was normally higher than that of fresh air, implying that denitrification occurred in the dump site. Argon assays indicate that both N₂ and N₂O production occurred inside waste and more significantly in the old section. The Ar assay would help for evaluations of N₂O emission in developing countries.

Implications: A long-term monitoring of composition of landfill gases in the region with high rainfall was conducted using an argon assay in order to discuss air intrusion into the dump site. Argon assays indicate that both N₂ and N₂O production occurred inside waste and more significantly in the old section.     

Experimental research of oily sawdust air gasification

This article shows oily sawdust gasification research on countercurrent installation. Experimental research was on a laboratory scale. The main purpose of the experiment was combustible gas production with higher CH₄ concentration. Gas concentrations like CO, CO₂, CH₄, H₂, and C_nH_m determine syngas composition. The technological parameter’s value defines experimental conditions. Value of this was fuel to air ratio. With fuel to air ratio change, syngas composition was a differential phenomenon where it depended on the process parameters like temperature. Additionally, evaluation of methane formation from CO, H₂, and CO₂ was done. Methanization coefficients were based on CO and CO₂ hydrogenation reactions. Component’s activity was in analogs way to syngas components changed.

     

Woody biomass and RPF gasification using reforming catalyst and calcium oxide

This study focused on steam gasification and reforming of waste biomass using a reforming catalyst. The purpose of the study was to evaluate the durability of a commercial Ni reforming catalyst and the effect of CaO on the reforming behavior, and to clarify detailed factors of catalytic performance, as well as the effect of operating parameters on the characteristics of produced gas composition. Moreover, catalyst regeneration was carried out and the behavior of catalytic activity based on gas composition was investigated. Using a fluidized bed gasifier and a fixed bed reformer, gasification and reforming of waste biomass were carried out. Commercial Ni-based catalyst and calcined limestone (CaO) were applied to the reforming reaction. Temperature of the gasifier and reformer was almost 1023 K. Ratio of steam to carbon in the feedstock [mol mol⁻¹] and equivalence ratio (i.e., ratio of actual to theoretical amount of oxygen) [-] were set at about 2 and 0.3, respectively. The feed rate of the feedstock into the bench-scale gasifier was almost 15 kg h⁻¹. The results of waste biomass gasification confirmed the improvement in H₂ composition by the CO₂ absorption reaction using the reforming catalyst and CaO. In addition, CaO proved to be especially effective in decreasing the tar concentration in the case of woody biomass gasification. Catalytic activity was maintained by means of catalyst regeneration processing by hydrogen reduction after air oxidation when woody biomass was used as feedstock.     

Manganese-cerium oxide (MnOx-CeO2) catalysts supported by titanium-bearing blast furnace slag for selective catalytic reduction of nitric oxide with ammonia at low temperature

A series of manganese-cerium oxide (MnO_x-CeO₂) catalysts supported by Ti-bearing blast furnace slag were prepared by wet impregnation and used for low-temperature selective catalytic reduction (SCR) of NO with NH₃. The slag-based catalyst exhibited high nitrogen oxide removal (deNO_x) activity and wide effective temperature range. Under the condition of NO = 500 ppm, NH₃ = 500 ppm, O₂ = 7–8 vol%, and total flow rate = 1600 mL/min, the Mn-Ce/Slag catalyst exhibited a NO conversion higher than 95% in the range of 180–260 °C. The activity of Mn/Slag catalysts was greatly enhanced with the addition of CeO₂. The results indicated that Ti-bearing blast furnace slag had suitable phase composition as good support of SCR catalyst.

Implications: Ti-bearing blast furnace slag is a kind of industrial waste in China. Much slag was underused and piling up, which could cause many environmental issues, such as enormous waste of titanium and groundwater and soil contamination by heavy metals in leachates. The utilization of slag as the support of SCR catalyst will not only make use of solid waste but also cut down the NO_x emitted from power plant.     

Synthesis of a novel slow-release potassium fertilizer from modified Pidgeon magnesium slag by potassium carbonate

A novel slow-release potassium fertilizer (SPF) was synthesized using Pidgeon magnesium slag (PMS) and potassium carbonate, which could minimize fertilizer nutrient loss and PMS disposal problems. Orthogonal experiments were conducted to determine the optimum conditions for synthesis. The potassium (K)-bearing compounds of SPF existed mainly in the form of crystalline phases Ca_1.197K_0.166SiO₄, K₂MgSiO₄, and K₄CaSi₃O₉, and in the noncrystalline phase. The active silicon content of SPF was 2.09 times as much as that of magnesium slag, and the slow-release character of SPF met the requirement for partly slow-release fertilizer in the national standard (GB/T23348-2009). The best models for describing the K release kinetics in water and 2% citric acid were the Elovich model and the first-order model, respectively. The heavy metal contents of SPF conformed to the national standard for organic–inorganic compound fertilizers, and the leaching mass concentrations of heavy metals and Fluorine were far lower than the limit values of the identification standard for hazardous waste identification for extraction toxicity (GB5085.3-2007), and also met the class II quality standard for ground water. The environmental risk of SPF is therefore very low, but because SPF is alkaline, its effect on soil pH should be taken into account.

Implications: PMS is the solid waste resulting from the production of magnesium metal by Pidgeon’s reduction process. Utilization of PMS in the high-technology and high-value areas may promote the high-efficiency development of worldwide collection metallic magnesium industry and contribute to the reduction of emissions of fine dust to air. This paper presents one of the new techniques in the use of PMS as a slow-release fertilizer by adding K₂CO₃. The product can serve as a very cost-effective and reliable artificial fertilizer.     

Translating landfill methane generation parameters among first-order decay models

Landfill gas (LFG) generation is predicted by a first-order decay (FOD) equation that incorporates two parameters: a methane generation potential (L₀) and a methane generation rate (k). Because non-hazardous waste landfills may accept many types of waste streams, multiphase models have been developed in an attempt to more accurately predict methane generation from heterogeneous waste streams. The ability of a single-phase FOD model to predict methane generation using weighted-average methane generation parameters and tonnages translated from multiphase models was assessed in two exercises. In the first exercise, waste composition from four Danish landfills represented by low-biodegradable waste streams was modeled in the Afvalzorg Multiphase Model and methane generation was compared to the single-phase Intergovernmental Panel on Climate Change (IPCC) Waste Model and LandGEM. In the second exercise, waste composition represented by IPCC waste components was modeled in the multiphase IPCC and compared to single-phase LandGEM and Australia’s Solid Waste Calculator (SWC). In both cases, weight-averaging of methane generation parameters from waste composition data in single-phase models was effective in predicting cumulative methane generation from -7% to +6% of the multiphase models. The results underscore the understanding that multiphase models will not necessarily improve LFG generation prediction because the uncertainty of the method rests largely within the input parameters. A unique method of calculating the methane generation rate constant by mass of anaerobically degradable carbon was presented (k_c) and compared to existing methods, providing a better fit in 3 of 8 scenarios. Generally, single phase models with weighted-average inputs can accurately predict methane generation from multiple waste streams with varied characteristics; weighted averages should therefore be used instead of regional default values when comparing models.

Implications: Translating multiphase first-order decay model input parameters by weighted average shows that single-phase models can predict cumulative methane generation within the level of uncertainty of many of the input parameters as defined by the Intergovernmental Panel on Climate Change (IPCC), which indicates that decreasing the uncertainty of the input parameters will make the model more accurate rather than adding multiple phases or input parameters.     

Production of sludge-incorporated paver blocks for efficient waste management

Waste management plays a vital role in the reuse of industry wastes in to useful conversions. The treatment of effluents from the combined textile effluent treatment plant and hypo sludge from the paper industry results in sludge generation, which poses a huge challenge for its disposal. Therefore, an eco-friendly attempt is made to utilize them in the production of paver blocks. Paver blocks are construction units that have vast applications in street roads, walking paths, fuel stations, and so on. In this study, an innovative attempt has been made to manufacture paver blocks incorporating textile effluent treatment plant sludge and hypo sludge, to utilize them in suitable proportions. The effect of adding silica fume and polypropylene fibre in paver blocks has also been studied. Paver blocks containing sludge with different proportions were cast based on the recommendations in Indian Standards (IS) 15658, and the test results were compared with the nominal M20 grade and M30 grade paver blocks. The outcomes of the paver block combinations were studied and found to be an effective utilization of sludge with substantial cement replacement of up to 35%, resulting in effective waste management for specific industries.

Implications: Presently, paver blocks are construction units that have vast application in street roads and other constructions like walking paths, fuel stations, and so on. Also, paver blocks possess easy maintenance during breakages. Based on this application, an innovative attempt has been made to manufacture paver blocks incorporating textile effluent treatment plant sludge and hypo sludge to utilize them in suitable proportions.     

Preparation and characterization of activated carbons from tobacco stem by chemical activation

Activated carbons were prepared from tobacco stem by chemical activation using potassium hydroxide (KOH), potassium carbonate (K₂CO₃), and zinc chloride (ZnCl₂). The effects of the impregnation ratio (activating agent/precursor) and activating agents on the physical and chemical properties of activated carbons were investigated. The textual structure and surface properties of activated carbons were characterized by nitrogen (N₂) adsorption isotherm, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), x-ray photoelectron spectroscopy (XPS), and thermogravimetry (TG). ZnCl₂, acting as a superior activating agent compared to the others, produced much more porosity. The maximum specific surface area reached 1347 m²/g, obtained by ZnCl₂ activation with an impregnation ratio of 4.0. Moreover, ZnCl₂ activation yielded products with an excellent thermostability, attributed to different activation mechanisms. Various oxygen functions were detected on the activated carbon surface, and hydroxyl and ester groups were found to be in the majority.

Implications: Tobacco stem, the residue from cigarette manufacturing, is usually discarded as waste, leading to serious resource waste and environmental problems. This study provides an effective utilization available for this solid residue by using it as the starting material in the preparation of activated carbon with chemical activation. Activated carbons with high specific area and various surface functions have been prepared, and the effects of the amount and type of activating agents on the physical and chemical properties of activated carbon were investigated as well.     

Napropamide Residues in Runoff and Infiltration Water from Pepper Production

Abstract

A field study was conducted on a Lowell silty loam soil of 2.7% organic matter at the Kentucky State University Research Farm, Franklin County, Kentucky. Eighteen universal soil loss equation (USLE) standard plots (22 × 3.7 m each) were established on a 10% slope. Three soil management practices were used: (i) class-A biosolids (sewage sludge), (ii) yard waste compost, each mixed with native soil at a rate of 50 ton acre^?1 on a dry-weight basis, and (iii) a no-mulch (NM) treatment (rototilled bare soil), used for comparison purposes. Devrinol 50-DF “napropamide” [N,N-diethyl-2-(1-naphthyloxy) propionamide]was applied as a preemergent herbicide, incorporated into the soil surface, and the plots were planted with 60-day-old sweet bell pepper seedlings. Napropamide residues one hour following spraying averaged 0.8, 0.4, and 0.3 μ g g^{? 1} dry soil in sewage sludge, yard waste compost, and no-mulch treatments, respectively. Surface runoff water, runoff sediment, and napropamide residues in runoff were significantly reduced by the compost and biosolid treatments. Yard waste compost treatments increased water infiltration and napropamide residues in the vadose zone compared to sewage sludge and NM treatments. Total pepper yields from yard waste compost amended soils (9187 lbs acre^?1) was significantly higher (P < 0.05) than yield from either the soil amended with class-A biosolids (6984 lbs acre^?1) or the no-mulch soil (7162 lbs acre ^?1).     

Deodorization of pig manure using lignin peroxidase with different electron acceptors

Odor pollution is a big environmental problem caused by large-scale livestock production in China, and developing a practical way to reduce these odors is pressing. In this study, a combination of 0.2–1.0 U/mL lignin peroxidase (LiP) and one of three peroxides (H₂O₂, CaO₂, 2Na₃CO₃·3H₂O₂) was examined for its efficiency in reducing the release of eight chemicals (propionic acid, isobutyric acid, isocaproic acid, isovaleric acid, phenol, p-cresol, indole, and skatole), NH₃, H₂S, and odor intensity from pig manure. The results showed an approximately 90% reduction in p-cresol, 40–60% reduction in odor intensity, 16.5–40% reduction in indolic compounds, and 25–40% reduction in volatile fatty acids. Being the electron acceptors of LiP, 2Na₃CO₃·3H₂O₂ and CaO₂ performed better than H₂O₂ in reducing the concentration of eight chemicals, NH_3, H₂S, and odor intensity from pig manure. The effect of deodorization can last for up to 72 hr.

Implications: In China, one of the major environmental problems caused by confined feeding is odor pollution, which brings a major threat to the sustainability, profitability, and growth of the livestock industry. To couple the LiP with the electron acceptors, a low–cost, simple, and feasible method for odor removal was established in this study. Based on the study results, a practical treatment method was provided for odor pollution and supply the farm operators a more flexible time to dispose treated manure.