Co-surfactant of ethoxylated sorbitan ester and sorbitan monooleate for enhanced flushing of tetrachloroethylene

This work evaluated the flushing efficiency of tetrachloroethylene (PCE) using the co-surfactant of non-ionic ethoxylated sorbitan ester (Tween) and oilphilic sorbitan monooleate (Span 80), which formed more hydrophobic micelles than Tween alone. The flushing efficiency was evaluated with laboratory columns filled with silica and aquifer sand. Results from column flushing were also compared to those of batch solubility experiments to study the removal mechanism by the co-surfactant solution. Compared to Tween 80 alone, the molar solubilization ratio and the affinity between the micelles and PCE increased 84% and 90%, respectively, by the co-surfactant solution of Tween 80 and Span 80 mixed at a 4:1 ratio. Flushing with 1% Tween 80 solution yielded a steady PCE recovery of 7% for both silica and aquifer sand in each pore volume (PV). Flushing with co-surfactant of 1% Tween 80 + Span 80 (4:1) further increased PCE recovery to 10% for silica sand and 13% for aquifer sand per PV. A comparison of results from column flushing and batch solubility tests indicated that the primary flushing mechanism of PCE using the co-surfactant solution of Tween 80 + Span 80 (4:1) was micellar solubilization.     

Impact of edible oil injection on the permeability of aquifer sands

Recent laboratory and field studies have shown that food-grade edible oils can be injected into the subsurface for installation of in-situ permeable reactive barriers. However to be effective, the oil must be distributed out away from the oil injection points without excessive permeability loss. In this work, we examine the distribution of soybean oil in representative aquifer sediments as non-aqueous phase liquid oil (NAPL oil) or as an oil-in-water emulsion. Laboratory columns packed with sands or clayey sands were flushed with either NAPL oil or a soybean emulsion followed by plain water, while monitoring permeability loss and the final oil residual saturation. NAPL oil can be injected into coarse-grained sands. However NAPL injection into finer grained sediments requires high injection pressures which may not be feasible at some sites. In addition, NAPL injection results in high oil residual saturations and moderate permeability losses. In contrast, properly prepared emulsions can be distributed through sands with varying clay content without excessive pressure buildup, low oil retention and very low to moderate permeability loss. For effective transport, the emulsion must be stable, the oil droplets must be significantly smaller than the mean pore size of the sediment and the oil droplets should have a low to moderate tendency to stick to each other and the aquifer sediments. In our work, oil retention and associated permeability loss increased with sediment clay content and with the ratio of droplet size to pore size. For sandy sediments, the permeability loss is modest (0-40% loss) and is proportional to the oil residual saturation.     

Use of vegetable oil in a pilot-scale denitrifying barrier

Nitrate in drinking water is a hazard to both humans and animals. Contaminated water can cause methemoglobinemia and may pose a cancer risk. Permeable barriers containing innocuous oils, which stimulate denitrification, can remove nitrate from flowing groundwater. For this study, a sand tank (1.1 x 2.0 x 0.085 m in size) containing sand was used as a one-dimensional open-top scale model of an aquifer. A meter-long area near the center of the tank contained sand coated with soybean oil. This region served as a permeable denitrifying barrier. Water containing 20 mg l(-1) nitrate-N was pumped through the barrier at a high flow rate, 1112 l week(-1), for 30 weeks. During the 30-week study, the barrier removed 39% of the total nitrate-N present in the water. The barrier was most efficient during the first 10 weeks of the study when almost all of the nitrate and nitrogen was removed. Efficiency declined with time so that by week 30 almost no nitrate was removed by the system. Nitrite levels in the effluent water remained low throughout the study. Barriers could be used to protect groundwater from nitrate contamination or for the in situ treatment of contaminated water. At the low flow rates that exist in most aquifers, such barriers should be effective at removing nitrate from groundwater for a much longer period of time.     

Accumulation of nitrite in denitrifying barriers when phosphate is limiting

Permeable in situ denitrifying barriers can remove nitrate from groundwater. Barriers may be constructed by filling an excavated area with a porous mixture of sand, fine gravel, and substrate or by the injection of a nonaqueous phase substrate into an aquifer. The substrate stimulates the development of a denitrifying microbial community by providing an electron donor. The objective of this study was to determine the ability of denitrifying barriers to function under low-phosphate conditions. Sand columns injected with a soybean oil emulsion were used as laboratory models of denitrifying barriers. When a natural groundwater containing 17 mg l(-1) nitrate-N and 0.009 mg l(-1) phosphate-P was pumped through the columns, only a small amount of nitrate was removed from the water and, in some effluent fractions, 52% to 88% of the influent nitrate had converted to nitrite. Nitrite also accumulated when the phosphate concentration of the groundwater was increased to 0.040 or 0.080 mg l(-1) phosphate-P. Only when a 0.160 mg l(-1) phosphate-P supplement was added to the groundwater was there a loss of nitrate without a large accumulation of nitrite. The addition of solid calcium phosphate or rock phosphate to the sand columns was found to provide adequate phosphate for denitrification in short-term studies. These studies point out the need to ensure that adequate phosphate is present in denitrifying barriers especially when such barriers are used beneath phosphate-binding soils.     

Effective distribution of emulsified edible oil for enhanced anaerobic bioremediation

Recent laboratory and field studies have shown that injection of emulsified edible oils can provide an effective, low-cost alternative for stimulating anaerobic biodegradation processes. A pilot-scale permeable reactive bio-barrier (PRBB) was installed at a perchlorate and chlorinated solvent impacted site by injecting 380 L of commercially available emulsion (EOS) containing emulsified soybean oil, food-grade surfactants, lactate, and yeast extract through ten direct push injection wells over a two day period. Soil cores collected six months after emulsion injection indicate the oil was distributed up to 5 m downgradient of the injection wells. A previously developed emulsion transport model was used to simulate emulsion transport and retention using independently estimated model parameters. While there was considerable variability in the soil sampling results, the model simulations generally agreed with the observed oil distribution at the field site. Model sensitivity analyses indicate that increasing the injection flow rate or diluting the oil with more water will have little effect on final oil distribution in the aquifer. The only effective approach for enhancing the spread of emulsified oil away from the injection well appears to be injecting a greater mass of oil.     

Nitrogen limited biobarriers remove atrazine from contaminated water: laboratory studies

Atrazine is one of the most frequently used herbicides. This usage coupled with its mobility and recalcitrant nature in deeper soils and aquifers makes it a frequently encountered groundwater contaminant. We formed biobarriers in sand filled columns by coating the sand with soybean oil; after which, we inoculated the barriers with a consortium of atrazine-degrading microorganisms and evaluated the ability of the barriers to remove atrazine from a simulated groundwater containing 1 mg L(-1) atrazine. The soybean oil provided a carbon rich and nitrogen poor substrate to the microbial consortium. Under these nitrogen-limiting conditions it was hypothesized that bacteria capable of using atrazine as a source of nitrogen would remove atrazine from the flowing water. Our hypothesis proved correct and the biobarriers were effective at removing atrazine when the nitrogen content of the influent water was low. Levels of atrazine in the biobarrier effluents declined with time and by the 24th week of the study no detectable atrazine was present (limit of detection<0.005 mg L(-1)). Larger amounts of atrazine were also removed by the biobarriers; when biobarriers were fed 16.3 mg L(-1) atrazine 97% was degraded. When nitrate (5 mg L(-1) N), an alternate source of nitrogen, was added to the influent water the atrazine removal efficiency of the barriers was reduced by almost 60%. This result supports the hypothesis that atrazine was degraded as a source of nitrogen. Poisoning of the biobarriers with mercury chloride resulted in an immediate and large increase in the amount of atrazine in the barrier effluents confirming that biological activity and not abiotic factors were responsible for most of the atrazine degradation. The presence of hydroxyatrazine in the barrier effluents indicated that dehalogenation was one of the pathways of atrazine degradation. Permeable barriers might be formed in-situ by the injection of innocuous vegetable oil emulsions into an aquifer or sandy soil and used to remove atrazine from a contaminated groundwater or to protect groundwater from an atrazine spill.     

Application of an empirical transport model to simulate retention of nanocrystalline titanium dioxide in sand columns

Nanocrystalline titanium dioxide was injected into sand columns to simulate subsurface injection for creation of a permeable treatment barrier. Past usage of this material as an ex situ pilot scale treatment filter has shown that it has a high adsorption capacity for a number of heavy metals and therefore would be a good candidate for injection technology. Three suspension concentrations (50, 75 and 100 mg l(-1)) were pumped through packed sand columns at different flow velocities (3.0, 6.8 and 14.1 cm min(-1)). Little to no particles was detected in the effluent. Most of the nanoparticles remained in the sand columns, with an increasing then decreasing retained solids pattern. Application of a one-dimensional advection-dispersion flow model, that included two empirical kinetic terms to account for particle retention in the porous media, produced data fits that followed the general trend of the data, but did not truly capture the concentration maxima in the data sets. Discussion of these results highlights the limited ability of existing models to aid in predicting particle retention of non-ideal materials for engineering purposes.     

Environmental features of two commercial surfactants widely used in soil remediation

One of the main limitations for a wider application of surfactants in soil remediation is the lack of knowledge about environmental fate and toxicity of surfactant itself especially for in situ application. Sorption behaviour, biodegradability, toxicity of parent compound and its metabolites are important processes that affect environmental fate of surfactants in site remediation applications. Tween 80 (poly(oxyethylene)(20)-sorbitane monooleate) and Aerosol MA+80 (dihexyl sodium sulfosuccinate) are surfactants that have been tested in laboratory and field scale remediation of soil and groundwater. In this work, the sorption and biodegradability of these surfactants were assessed to provide conditions and limitations for their use. The soil used in this experimentation was analysed for organic carbon content, soil bacteria, and size fraction and resulted to be a good model because is characterised by mean values for almost all considered parameters. Tween 80 showed high degree of biodegradability but a high affinity for soil matrix. Results suggest that Tween 80 could find its best application in ex situ solid phase remediation like ex situ bioremediation; its high affinity to soil could limit in situ applications. Biodegradation tests for Aerosol MA+80 show low degree of biodegradability and mineralisation. Biodegradation experiments, coupled with analysis of toxicity, could support the hypothesis that degradation of Aerosol MA+80 is not complete and leads to an accumulation of intermediates with at least the same toxicity of the parental compound. Therefore, aquifer remediation application with Aerosol MA+80 has to be conducted with necessary precautions to avoid product loss and excess surfactant should be flushed from the soil.     

Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 1. Experimental studies

A matrix of batch, column and two-dimensional (2-D) box experiments was conducted to investigate the coupled effects of rate-limited solubilization and layering on the entrapment and subsequent recovery of a representative dense NAPL, tetrachloroethylene (PCE), during surfactant flushing. Batch experiments were performed to determine the equilibrium solubilization capacity of the surfactant, polyoxyethylene (20) sorbitan monooleate (Tween 80), and to measure fluid viscosity, density and interfacial tension. Results of one-dimensional column studies indicated that micellar solubilization of residual PCE was rate-limited at Darcy velocities ranging from 0.8 to 8.2 cm/h and during periods of flow interruption. Effluent concentration data were used to develop effective mass transfer coefficient (Ke) expressions that were dependent upon the Darcy velocity and duration of flow interruption. To simulate subsurface heterogeneity, 2-D boxes were packed with layers of F-70 Ottawa sand and Wurtsmith aquifer material within 20-30 mesh Ottawa sand. A 4% Tween 80 solution was then flushed through PCE-contaminated boxes at several flow velocities, with periods of flow interruption. Effluent concentration data and visual observations indicated that both rate-limited solubilization and pooling of PCE above the fine layers reduced PCE recovery to levels below those anticipated from batch and column measurements. These experimental results demonstrate the potential impact of both mass transfer limitations and subsurface layering on the recovery of PCE during surfactant enhanced aquifer remediation.     

Electrolytic transformation of ordinance related compounds (ORCs) in groundwater: laboratory mass balance studies

Electrolytic reactive barriers (e(-) barriers) consist of closely spaced permeable electrodes installed across a groundwater contaminant plume in a permeable reactive barrier format. Application of sufficient potential to the electrodes results in sequential oxidation and reduction of the target contaminant. The objective of this study was to quantify the mass distribution of compounds produced during sequential electrolytic oxidation and reduction of ordinance related compounds (ORCs) in a laboratory analog to an e(-) barrier. In this study, a series of column tests were conducted using RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine) and TNT (2,4,6-trinitrotoluene) as representative ORCs. The experimental setup consisted of a plexiglass column packed with quartz-feldspar sand to simulate aquifer conditions. A single set of porous electrodes consisting of expanded titanium-mixed metal oxide mesh was placed at the midpoint of the sand column as a one-dimensional analog to an e(-) barrier. Constant current of 20mA (variable voltage) was applied to the electrode set. Initial studies involved quantification of reaction products using unlabeled RDX and TNT. Approximately 70% of the influent concentration was transformed, in one pass, through sequential oxidation-reduction for both contaminants. Following the unlabeled studies, (14)C labeled RDX and TNT were introduced to determine the mass balance. An activity balance of up to 96% was achieved for both (14)C-RDX and (14)C-TNT. For both contaminants, approximately 21% of the influent activity was mineralized to (14)CO(2). The proportion of the initial activity in the dissolved fraction was different for the two test contaminants. Approximately 30% of the initial (14)C-RDX was recovered as unreacted in the dissolved phase. The balance of the (14)C-RDX was recovered as non-volatile, non-nitroso transformation products. None of the (14)C-RDX was sorbed to the column sand packing. For (14)C-TNT approximately 51% of the initial activity was recovered in the dissolved phase, the majority was unreacted TNT. The balance of the (14)C-TNT was either sorbed to the sand packing (approximately 24%) or dissolved/mineralized as unidentified ring cleavage products ( approximately 4%).     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Investigations on mobility of carbon colloid supported nanoscale zero-valent iron (nZVI) in a column experiment and a laboratory 2D-aquifer test system

Nanoscale zero-valent iron (nZVI) has recently gained great interest in the scientific community as in situ reagent for installation of permeable reactive barriers in aquifer systems, since nZVI is highly reactive with chlorinated compounds and may render them to harmless substances. However, nZVI has a high tendency to agglomerate and sediment; therefore it shows very limited transport ranges. One new approach to overcome the limited transport of nZVI in porous media is using a suited carrier colloid. In this study we tested mobility of a carbon colloid supported nZVI particle “Carbo-Iron Colloids” (CIC) with a mean size of 0.63 μm in a column experiment of 40 cm length and an experiment in a two-dimensional (2D) aquifer test system with dimensions of 110?×?40?×?5 cm. Results show a breakthrough maximum of 82 % of the input concentration in the column experiment and 58 % in the 2D-aquifer test system. Detected residuals in porous media suggest a strong particle deposition in the first centimeters and few depositions in the porous media in the further travel path. Overall, this suggests a high mobility in porous media which might be a significant enhancement compared to bare or polyanionic stabilized nZVI.     

Surfactant-enhanced biodegradation of crude oil by mixed bacterial consortium in contaminated soil

This study evaluated the effects of two surfactants (i.e., Tween 80 and SDS) on biodegradation of crude oil by mixed bacterial consortium in soil-aqueous system. The mixed bacterial consortium was domesticated from the activated sludge of cooking plant through a progressive domestication process. High-throughput sequencing analysis revealed that Rhodanobacter sp. was the dominant bacteria. The higher CMC_eff value for two surfactants was observed in soil-aqueous system compared with that in aqueous system, which was likely due to their adsorption onto soil particles. Either Tween 80 or SDS can be utilized as carbon source and promote the growth of mixed bacterial consortium. Further findings evidenced that the degradation of crude oil can be enhanced by adding either Tween 80 or SDS. The performance of Tween 80 was generally superior to SDS for the crude oil degradation. The highest crude oil degradation efficiency was 42.2 and 31.0% under the conditions of 5 CMC_eff of Tween 80 and 2 CMC_eff of SDS, respectively. Furthermore, the degradation efficiency of crude oil in remediation experiment (i.e., 77%) evidenced that the integration of adding Tween 80 and inoculating mixed bacterial consortium was effective for crude oil-contaminated soil decontamination.     

Hexadecane and pristane degradation potential at the level of the aquifer—evidence from sediment incubations compared to in situ microcosms

Monitored natural attenuation is widely accepted as a sustainable remediation method. However, methods providing proof of proceeding natural attenuation within the water-unsaturated (vadose) zone are still relying on proxies such as measurements of reactive and non-reactive gases, or sediment sampling and subsequent mineralisation assays, under artificial conditions in the laboratory. In particular, at field sites contaminated with hydrophobic compounds, e.g. crude oil spills, an in situ evaluation of natural attenuation is needed, because in situ methods are assumed to provide less bias than investigations applying either proxies for biodegradation or off-site microcosm experiments. In order to compare the current toolbox of methods with the recently developed in situ microcosms, incubations with direct push-sampled sediments from the vadose and the aquifer zones of a site contaminated with crude oil were carried out in conventional microcosms and in situ microcosms. The results demonstrate the applicability of the in situ microcosm approach also outside water-saturated aquifer conditions in the vadose zone. The sediment incubation experiments demonstrated turnover rates in a similar range (vadose, 4.7 mg/kg*day; aquifer, 6.4 mg_hexadecane/kg_soil/day) of hexadecane degradation in the vadose zone and the aquifer, although mediated by slightly different microbial communities according to the analysis of fatty acid patterns and amounts. Additional experiments had the task of evaluating the degradation potential for the branched-chain alkane pristane (2,6,10,14-tetramethylpentadecane). Although this compound is regarded to be hardly degradable in comparison to n-alkanes and is thus frequently used as a reference parameter for indexing the extent of biodegradation of crude oils, it could be shown to be degraded by means of the incubation experiments. Thus, the site had a high inherent potential for natural attenuation of crude oils both in the vadose zone and the aquifer.     

表面活性剂在北京碱性土壤中的吸附行为研究

通过静态吸附实验,研究了北京碱性土壤对阴离子表面活性剂SDS、阳离子表面活性剂CTAB和非离子表面活性剂Tween80的吸附行为,考察了温度对表面活性剂吸附的影响.结果表明:7种不同土样对SDS、CTAB和Tween80的吸附等温线均较好地符合Langmuir吸附模式,其吸附能力的大小顺序为2号轻壤土》轻粘土》中壤土》砂壤土》5号轻壤土》重壤土》紧砂土,这主要是由于7种土样的pH、有机质含量和机械组成不同的缘故;同一土壤中,CTAB的吸附量》Tween80的吸附量》SDS的吸附量;温度的升高,不利于SDS和CTAB在土壤中的吸附,而有利于Tween80的吸附.     

Can chemical oxidation improve the permeability of infiltration basins?

The Rapid Infiltration and Extraction (RIX) facility, a soil aquifer treatment system, began taking secondary effluent from the City of San Bernardino, California, in 1996. The gradual decrease in the hydraulic conductivity of the infiltration basins at RIX has been attributed to the accumulation of organic matter in the surface sand. Periodic tillage of the surface sand to restore the permeability has mixed this organic matter to a depth of nearly 50 cm. We hypothesized that in situ chemical oxidation of the surface sand might improve the infiltration rate and increase the time between filling and drying cycles. The effect of organic matter oxidation on sand permeability was tested in laboratory sand columns treated with sodium hypochlorite, calcium hypochorite, and ozone gas. All oxidants significantly decreased the hydraulic conductivity of the surface sand. The loss in permeability was attributed to an increase in dispersed clay plus silt-sized particles that were released as a result of oxidation. This study suggests that ex situ sand-washing operations, currently being used to clean the sand, could be improved by the addition of oxidants to the wash water.     

Evaluation of bioremediation effectiveness on crude oil-contaminated sand

A treatability study was conducted using sea sand spiked with 3% or 6% (w/w) of Arabian light crude oil to determine the most effective bioremediation strategies for different levels of contamination. The sea sand used in the study was composed of gravel (0.1%), sand (89.0%), and silt and clay (10.9%). The water content of the sea sand was adjusted to 12.6% (w/w) for the study. Different combinations of the following treatments were applied to the sand in biometer flasks: the concentration of oil (3% or 6%), the concentration of a mixture of three oil-degrading microorganisms (Corynebacterium sp. IC-10, Sphingomonas sp. KH3-2 and Yarrowia sp. 180, 1x10(6) or 1x10(8) cells g-1 sand), the concentration of the surfactant Tween 80 (1 or 10 times the critical micelle concentration), and the addition of SRIF in a C:N:P ratio of 100:10:3. Three biometer flasks per combination of experimental conditions were incubated, and the performance of each treatment was examined by monitoring CO2 evolution, microbial activity, and oil degradation rate. The results suggest that the addition of inorganic nutrients accelerated the rate of CO2 evolution by a factor of 10. The application of oil-degrading microorganisms in a concentration greater than that of the indigenous population clearly increased biodegradation efficiency. The application of surfactant slightly enhanced the oil degradation rate in the contaminated sand treated with the higher concentration of oil-degrading microorganisms. The initial CO2 evolution rate was shown to efficiently evaluate the treatability test by providing significant data within a short period, which is critical for the rapid determination of the appropriate bioremediation approach. The measurements of microbial activity and crude oil degradation also confirmed the validity of the CO2 evolution rate as an appropriate criterion.     

Concurrent bioremediation of perchlorate and 1,1,1-trichloroethane in an emulsified oil barrier

A detailed field pilot test was conducted to evaluate the use of edible oil emulsions for enhanced in situ biodegradation of perchlorate and chlorinated solvents in groundwater. Edible oil substrate (EOS) was injected into a line of ten direct push injection wells over a 2-day period to form a 15-m-long biologically active permeable reactive barrier (bio-barrier). Field monitoring results over a 2.5-year period indicate the oil injection generated strongly reducing conditions in the oil-treated zone with depletion of dissolved oxygen, nitrate, and sulfate, and increases in dissolved iron, manganese and methane. Perchlorate was degraded from 3100 to 20,000 microg/L to below detection (<4 microg/L) in the injection and nearby monitor wells within 5 days following the injection. Two years after the single emulsion injection, perchlorate was less than 6 microg/L in every downgradient well compared to an average upgradient concentration of 13,100 microg/L. Immediately after emulsion injection, there were large shifts in concentrations of chlorinated solvents and degradation products due to injection of clean water, sorption to the oil and adaptation of the in situ microbial community. Approximately 4 months after emulsion injection, concentrations of 1,1,1-trichloroethane (TCA), perchloroethene (PCE), trichloroethene (TCE) and their degradation products appeared to reach a quasi steady-state condition. During the period from 4 to 18 months, TCA was reduced from 30-70 microM to 0.2-4 microM during passage through the bio-barrier. However, 1-9 microM 1,1-dichloroethane (DCA) and 8-14 microM of chloroethane (CA) remained indicating significant amounts of incompletely degraded TCA were discharging from the oil-treated zone. During this same period, PCE and TCE were reduced with concurrent production of 1,2-cis-dichloroethene (cis-DCE). However, very little VC or ethene was produced indicating reductive dechlorination slowed or stopped at cis-DCE. The incomplete removal of TCA, PCE and TCE is likely associated with the short (5-20 days) hydraulic retention time of contaminants in the oil-treated zone. The permeability of the injection wells declined by 39-91% (average=68%) presumably due to biomass growth and/or gas production. However, non-reactive tracer tests and detailed monitoring of the perchlorate plume demonstrated that the permeability loss did not result in excessive flow bypassing around the bio-barrier. Contaminant transport and degradation within the bio-barrier was simulated using an advection-dispersion-reaction model where biodegradation rate was assumed to be linearly proportional to the residual oil concentration (Soil) and the contaminant concentration. Using this approach, the calibrated model was able to closely match the observed contaminant distribution. The calibrated model was then used to design a full-scale barrier to treat both ClO4 and chlorinated solvents.     

Progression of natural attenuation processes at a crude oil spill site: II. Controls on spatial distribution of microbial populations

A multidisciplinary study of a crude-oil contaminated aquifer shows that the distribution of microbial physiologic types is strongly controlled by the aquifer properties and crude oil location. The microbial populations of four physiologic types were analyzed together with permeability, pore-water chemistry, nonaqueous oil content, and extractable sediment iron. Microbial data from three vertical profiles through the anaerobic portion of the contaminated aquifer clearly show areas that have progressed from iron-reduction to methanogenesis. These locations contain lower numbers of iron reducers, and increased numbers of fermenters with detectable methanogens. Methanogenic conditions exist both in the area contaminated by nonaqueous oil and also below the oil where high hydrocarbon concentrations correspond to local increases in aquifer permeability. The results indicate that high contaminant flux either from local dissolution or by advective transport plays a key role in determining which areas first become methanogenic. Other factors besides flux that are important include the sediment Fe(II) content and proximity to the water table. In locations near a seasonally oscillating water table, methanogenic conditions exist only below the lowest typical water table elevation. During 20 years since the oil spill occurred, a laterally continuous methanogenic zone has developed along a narrow horizon extending from the source area to 50-60 m downgradient. A companion paper [J. Contam. Hydrol. 53, 369-386] documents how the growth of the methanogenic zone results in expansion of the aquifer volume contaminated with the highest concentrations of benzene, toluene, ethylbenzene, and xylenes.     

Field test of a cross-injection scheme for stimulating in situ denitrification near a municipal water supply well

A pilot-scale test of an in situ denitrification scheme was undertaken to assess an adaptation of the nutrient injection wall (NIW) technology for treating a deep (30-40 m) nitrate contamination problem (N-NO(-)(3) ~ 10-12 mg/L). The adaptation is called the Cross-Injection Scheme (CIS). It duplicates the NIW method without a wall; wells are installed and operated directly in the aquifer and high-flux zones of the aquifer are preferentially targeted for treatment. The test was conducted on the site of a municipal water supply well field, with the supply well pumping between 15-80 m(3)/h. Acetate was periodically injected into the aquifer between an injection-extraction well pair positioned across the normal direction of flow. The injected pulses were then permitted to move with the water toward the municipal wells, providing a carbon supply to drive the desired denitrification. The fate of nitrate, nitrite, acetate and sulphate were monitored at multilevel wells located between the injection location and the municipal wells. The acetate pulsing interval was approximately weekly (9 h injections), so that the system was operating passively 95% of the time. Previous work on the site has established that the highest solute fluxes were associated with a 1-3 m thick zone about 35 m below surface. This zone was found to respond to the acetate additions as a function of the municipal pumping rate and the carbon-to-nitrogen ratio (i.e., determined by the injected acetate concentration). Initially, acetate was injected just below the theoretical stoichiometric requirement for complete denitrification and nitrate disappearance was accompanied by nitrite production. Increasing the C:N ratio (doubling the acetate injection concentration) increased the removal of nitrate and diminished the occurrence of nitrite. Slowing the municipal pumping rate, with a C:N ratio of 1.2-1.6, resulted in complete nitrate attenuation with no nitrite production and no sulfate reduction. The experiment demonstrated that the CIS injection scheme is a viable option for the treatment of nitrate contamination in situ near high-capacity wells.