An interlaboratory comparison of nanosilver characterisation and hazard identification: Harmonising techniques for high quality data

Within the FP7 EU project NanoValid a consortium of six partners jointly investigated the hazard of silver nanoparticles (AgNPs) paying special attention to methodical aspects that are important for providing high-quality ecotoxicity data. Laboratories were supplied with the same original stock dispersion of AgNPs. All partners applied a harmonised procedure for storage and preparation of toxicity test suspensions. Altogether ten different toxicity assays with a range of environmentally relevant test species from different trophic levels were conducted in parallel to AgNP characterisation in the respective test media. The paper presents a comprehensive dataset of toxicity values and AgNP characteristics like hydrodynamic sizes of AgNP agglomerates and the share (%) of Ag⁺-species (the concentration of Ag⁺-species in relation to the total measured concentration of Ag). The studied AgNP preparation (20.4 ± 6.8 nm primary size, mean total Ag concentration 41.14 mg/L, 46–68% of soluble Ag⁺-species in stock, 123.8 ± 12.2 nm mean z-average value in dH₂O) showed extreme toxicity to crustaceans Daphnia magna, algae Pseudokirchneriella subcapitata and zebrafish Danio rerio embryos (EC50 < 0.01 mg total Ag/L), was very toxic in the in vitro assay with rainbow trout Oncorhynchus mykiss gut cells (EC50: 0.01–1 mg total Ag/L); toxic to bacteria Vibrio fischeri, protozoa Tetrahymena thermophila (EC50: 1–10 mg total Ag/L) and harmful to marine crustaceans Artemia franciscana (EC50: 10–100 mg total Ag/L). Along with AgNPs, also the toxicity of AgNO₃ was analyzed. The toxicity data revealed the same hazard ranking for AgNPs and AgNO₃ (i.e. the EC50 values were in the same order of magnitude) proving the importance of soluble Ag⁺-species analysis for predicting the hazard of AgNPs. The study clearly points to the need for harmonised procedures for the characterisation of NMs. Harmonised procedures should consider: (i) measuring the AgNP properties like hydrodynamic size and metal ions species in each toxicity test medium at a range of concentrations, and (ii) including soluble metal salt control both in toxicity testing as well as in Ag⁺-species measurements. The present study is among the first nanomaterial interlaboratory comparison studies with the aim to improve the hazard identification testing protocols.     

Concentrations, transport, fate, and releases of polybrominated diphenyl ethers in sewage treatment plants in the Pearl River Delta, South China

Wastewater has proved to be a significant source of polybrominated diphenyl ethers (PBDEs) in the environment. Seventeen congeners from tri- to deca-BDEs were determined to characterize the occurrence, fate, and transport of PBDEs in two sewage treatment plants in the Pearl River Delta, South China. The PBDE concentrations varied substantially from 13.3 to 2496.4 ng L(-1) in the raw wastewater, depending on the wastewater types and contents of the suspended particulate matter (SPM). The concentrations declined to 0.9 to 4.4 ng L(-1) in the treated effluent and were closely associated with SPM contents. BDE-209 was the predominant congener in the wastewater and sewage sludge. Most of PBDEs might have ended up in the sewage sludge, with <4.7% being discharged with the treated effluent. The results revealed that PBDEs were not significantly degraded by biological treatment and chlorination in the STPs. An annual release of PBDEs was estimated at 2280 kg/year through wastewater from the Pearl River Delta.     

234U and 230Th determination by FIA-ICP-MS and application to uranium-series disequilibrium in marine samples

A 234U and 230Th determination method based on an extraction chromatographic separation on a flow injection system coupled to a quadruple ICP-MS was developed. Two-milliliter UTEVA (Eichrom Co.) cartridges were applied as separation tool and 236U and 229Th as spikes. Loading and washing steps were carried out in 3 M HNO3 solution and 0.05 M ammonium oxalate applied to elute both uranium and thorium. The method was applied initially to the IAEA-327 soil reference sample and NIST SRM 4357 ocean sediment reference material, with the obtained 234U and 230Th concentrations in agreement with the reference levels. Samples from a deep-sea sediment core (2450 m water depth) were analyzed and based on 230Th/234U dating, a mean sedimentation rate of 3.3 cm ky(-1) was calculated. Samples from two sediment layers were also dated by 14C-AMS and the observed ages agree with the 230Th/234U results.     

Thorium accumulation in the sedimentary environment of the Vigo Ria (NW Iberian Peninsula)

Thorium levels and their association with Fe, Sc, Ca, and Particulate Organic Carbon (POC) were researched in sediments of the Vigo Ria in order to assess the influence of radioactive gneisses from the neighbouring continental Gali?eiro Complex. Sediment of 50 surface samples and 1 core was analysed by ICP-MS and the results were validated with certificate reference material from marine sediment. It was found that Th accumulates in the middle Ria zone (9-15 mg kg(-1)) as a result of the terrestrial source. The thorium concentration in the Ria (average: 9.4+/-5.1 mg kg(-1)) is not anthropogenically impacted in accordance with its own regional background level (11.4+/-3.5 mg kg(-1)), which is two times higher than the content in earth's crust. Throughout the relationship Th/Fe, Th may be associated with the iron cycle in the Ria, probably through iron oxy-hydroxide scavenging.     

Radioactive and stable metal bioaccumulation, crystalline compound and siderophore detection in Clavariadelphus truncatus

137Cs and 40K activity concentrations and stable elements have been measured in Clavariadelphus truncatus collected in Mexico. Iron-chelating compounds of siderophore-type was also studied in the species. 137Cs and 40K were determined in soil and mushroom samples with HpGe gamma-ray spectrometry. Macro- and micro-elemental concentrations were determined by XRF and ICP-MS. Siderophore detection was obtained with a colorimetric assay and X-ray diffraction analysis was performed using a Siemens D5000 diffractometer. 137Cs geometric mean concentration in C. truncatus was 26 times higher as compared with other Mexican edible mushroom species, while 40K showed stability. Soil-C. truncatus concentration ratio for 137Cs and other micro-elements such as Cs, Rb and Pb were also higher than other Mexican edible species. The 137Cs committed effective dose due to the ingestion of C. truncatus was 8 x 10(-6) Sv year(-1). The main crystalline structure found in C. truncatus was D-Mannitol.     

Thorium and uranium contents in human urine: influence of age and residential area

Inductively coupled plasma mass spectrometry (ICP-MS) has been used for the determination of (232)Th and (238)U in urine of unexposed Jordanian subjects living in six cities. The range of (232)Th excretion in all subjects was found to be 1.4-640 microBq d(-1) with an average of 34.8 microBq d(-1) (geometric mean 15.8 microBq d(-1)). Results showed no statistically significant correlation with age and residential area. The average value obtained is in agreement with levels considered normal in some recent publications. The average value of (238)U in all samples was found to be 3955 microBq d(-1) (geometric mean 1107 microBq d(-1)), which is higher than reported figures from Germany and India, but in agreement with those figures given in ICRP publication, number 23. The mean values of the different groups were found to be proportional to age up to 60 years. A noticeable drop is observed for subjects greater than 60 years old.     

基于实测光谱分析和MODIS数据鄱阳湖叶绿素a浓度估算

基于遥感的大面积水体监测技术为水环境监测提供了一种有效手段。以鄱阳湖为研究区,以反映水体营养状态的重要指标叶绿素a为研究对象,在测定研究区水体光谱及叶绿素a浓度和收集了相应时间的MODIS数据的基础上,采用浮游藻类指数法（Floating Algae Index,FAI）提取鄱阳湖水体范围,对鄱阳湖水体实测光谱数据进行剔除异常、归一化及光谱微分处理,构建波段差值、比值、归一化差值等光谱指数,利用最小二乘原理迭代分析水体叶绿素光谱响应特征,得出敏感波段范围：673～680 nm与650～665 nm、680～710 nm与650～670 nm、662～671 nm与700～720 nm光谱区间组合。选择最佳通道组合,建立基于MODIS影像的鄱阳湖叶绿素a浓度反演模型,相关系数为067。应用该模型得到2011年秋季鄱阳湖的叶绿素浓度估算值,反演结果显示湖区水体叶绿素浓度总体不高,且在空间分布上湖区水体周边与陆地交界处比湖中心区浓度偏高。分析认为：通过对实测光谱的定量分析,获得对鄱阳湖地区水体叶绿素浓度的光谱特征认识,揭示出其反射光谱的长波漂移现象,为鄱阳湖这一富营养化程度底,且水体分布不均匀区域建立一种叶绿素浓度反演方法,可为该区域长期的水环境管理提供方法借鉴     

Radioactive impact in sediments from an estuarine system affected by industrial wastes releases

A big fertilizer industrial complex and a vast extension of phosphogypsum piles (12 km2), sited in the estuary formed by the Odiel and Tinto river mouths (southwest of Spain), are producing an unambiguous radioactive impact in their surrounding aquatic environment through radionuclides from the U-series. The levels and distribution of radionuclides in sediments from this estuarine system have been determined. The analyses of radionuclide concentrations and activity ratios have provided us with an interesting information to evaluate the extension, degree and routes of the radioactive impact, as well as for the knowledge of the different pathways followed for the radioactive contamination to disturb this natural system. The obtained results indicate that the main pathway of radioactive contamination of the estuary is through the dissolution in its waters of the radionuclides released by the industrial activities and their later fixation on the particulate materials. Tidal activity also plays an important role in the transport and homogenization along the estuary of the radioactivity released from the fertilizer plants.     

Determination of extremely low (236)U/(238)U isotope ratios in environmental samples by sector-field inductively coupled plasma mass spectrometry using high-efficiency sample introduction

A method by inductively coupled plasma mass spectrometry (ICP-MS) was developed which allows the measurement of (236)U at concentration ranges down to 3 x 10(-14)g g(-1) and extremely low (236)U/(238)U isotope ratios in soil samples of 10(-7). By using the high-efficiency solution introduction system APEX in connection with a sector-field ICP-MS a sensitivity of more than 5,000 counts fg(-1) uranium was achieved. The use of an aerosol desolvating unit reduced the formation rate of uranium hydride ions UH(+)/U(+) down to a level of 10(-6). An abundance sensitivity of 3 x 10(-7) was observed for (236)U/(238)U isotope ratio measurements at mass resolution 4000. The detection limit for (236)U and the lowest detectable (236)U/(238)U isotope ratio were improved by more than two orders of magnitude compared with corresponding values by alpha spectrometry. Determination of uranium in soil samples collected in the vicinity of Chernobyl nuclear power plant (NPP) resulted in that the (236)U/(238)U isotope ratio is a much more sensitive and accurate marker for environmental contamination by spent uranium in comparison to the (235)U/(238)U isotope ratio. The ICP-MS technique allowed for the first time detection of irradiated uranium in soil samples even at distances more than 200 km to the north of Chernobyl NPP (Mogilev region). The concentration of (236)U in the upper 0-10 cm soil layers varied from 2 x 10(-9)g g(-1) within radioactive spots close to the Chernobyl NPP to 3 x 10(-13)g g(-1) on a sampling site located by >200 km from Chernobyl.     

Application of ICP-QMS for the determination of plutonium in environmental samples for safeguards purposes

Aiming to determine the plutonium amount as well as its isotopic composition, in particular, in swipe samples for safeguards purposes, an analytical method was developed with a plutonium separation step based on extraction chromatography using 2 cm TEVA columns and detection with quadrupole ICP-MS applying an ultra-sonic nebulizer coupled with membrane desolvation system. The method was successfully applied to New Brunswick plutonium certified reference materials as well as to Lawrence Livermore National Laboratory round robin samples, based on the round robin samples provided by the Institute for Reference Materials and Measurements (Belgium), as part of the Regular European Interlaboratory Measurement Evaluation Programme (REIMEP), campaign 16 (isotopic abundances of plutonium in plutonium nitrate samples), with a total plutonium amount between 1 and 0.25 ng per sample. After the introduction of an additional separation step, it was also possible to carry out precise and accurate total plutonium, (240)Pu/(239)Pu, (241)Pu/(239)Pu and (242)Pu/(239)Pu atom ratios determination in sediment sample showing its applicability to environmental samples in general, reaching a detection limit equivalent to 5 mBq(239)Pu kg(-1).     

BOD-DO modeling and water quality analysis of a waste water outfall off Kochi, west coast of India

Water quality scenarios around an offshore outfall off Kochi were simulated using MIKE21 water quality model, assuming a high Biochemical Oxygen Demand (BOD=50 mg l(-1)) effluent discharge. The discharge is introduced into the model through an outfall located at a distance of 6.8 km from the shore at a depth of 10 m. Three scenarios were simulated with different discharge rates such as 2, 5 and 10 m3 s(-1), with BOD load of 8640, 21,600 and 43,200 kg day(-1) respectively. Model simulations were carried out to estimate the assimilation capacity of the waters off Kochi for the three discharge rates. The results show that for 10 m3 s(-1) effluent discharge, the initial BOD of 50 mg l(-1) reduced to 3.33 mg l(-1) at the outfall after 48 h. High BOD values were confined to an elliptical area of approximately 8 km2 around the outfall. Based on this, the assimilative capacity of the waters off Kochi in terms of BOD can be estimated as 38,000 kg day(-1). It is suggested that offshore waters could be used as a feasible alternative to the Kochi backwaters for the disposal of treated effluent.     

A study on natural radiation exposure in different realistic living rooms

In the first part of the paper, the factors affecting 222Rn properties in 25 different realistic living rooms (with low ventilation rates) of different houses in El-Minia City (Upper Egypt) have been studied; they included the activity concentration of 222Rn gas (C(o)), the unattached fraction (f(p)) of 218Po and 214Pb, the unattached potential alpha energy concentration (PAEC) and the equilibrium factor (F). The activity distributions of unattached 218Po and 214Pb as well as for the PAEC were determined. With a dosimetric model calculation [ICRP, 1994b. Human Respiratory Tract Model For Radiological Protection. Pergamon Press, Oxford. ICRP Publication 66] the total deposition fraction of unattached 218Po and 214Pb in human respiratory tract was evaluated to determine the total equivalent dose. An electrostatic precipitation method and a wire screen diffusion battery technique were both employed for the determination of 222Rn gas concentration and its unattached decay products, respectively. The mean activity concentration of 222Rn gas (C(o)) was found to be 110+/-20 Bq m(-3). The mean unattached activity concentrations of 218Po and 214Pb were found to be 0.6 and 0.35 Bq m(-3), respectively. A mean unattached fraction (f(p)) of 0.09+/-0.01 was obtained at a mean aerosol particle concentration (Z) of (2.9+/-0.23) x 10(3)cm(-3). The mean equilibrium factor (F) was determined to be 0.31+/-0.02. The mean PAEC of unattached 218Po and 214Pb was found to be 8.74+/-2.1 Bq m(-3). The activity distributions of 218Po and 214Pb show mean activity median diameters (AMD) of 1.5 and 1.85 nm with mean geometric standard deviations (SD) of 1.33 and 1.45, respectively. The mean activity distribution of the PAEC shows an AMD of 1.65 nm with a geometric standard deviation of 1.25. At a total deposition fraction of about 97% the total equivalent dose to the lung was determined to be about 133 microSv. The second part of this paper deals with a study of natural radionuclide contents of samples collected from the building materials of the rooms under investigations in part one. Analyses were performed in Marinelli beakers with a gamma multichannel analyzer equipped with a NaI(Tl) detector. The samples revealed the presence of the uranium-radium and thorium radioisotopes as well as 40K. Nine gamma-lines of the natural radioisotopes corresponding to 212Pb, 214Pb, 214Bi, 228Ac, 40K and 208Tl were detected and measured. The activity concentrations of 226Ra, 232Th and 40K were determined with mean activity concentrations of 58+/-19, 31+/-11 and 143+/-62 Bq kg(-1), respectively. These activities amount to a radium equivalent (Ra(eq)) of 113 Bq kg(-1) and to a mean value of external hazard index of 0.31.     

Silver nanoparticles: behaviour and effects in the aquatic environment

This review summarises and evaluates the present knowledge on the behaviour, the biological effects and the routes of uptake of silver nanoparticles (Ag NPs) to organisms, with considerations on the nanoparticle physicochemistry in the ecotoxicity testing systems used. Different types of Ag NP syntheses, characterisation techniques and predicted current and future concentrations in the environment are also outlined. Rapid progress in this area has been made over the last few years, but there is still a critical lack of understanding of the need for characterisation and synthesis in environmental and ecotoxicological studies. Concentration and form of nanomaterials in the environment are difficult to quantify and methodological progress is needed, although sophisticated exposure models show that predicted environmental concentrations (PECs) for Ag NPs in different environmental compartments are at the range of ng L(-1) to mg kg(-1). The ecotoxicological literature shows that concentrations of Ag NPs below the current and future PECs, as low as just a few ng L(-1), can affect prokaryotes, invertebrates and fish indicating a significant potential, though poorly characterised, risk to the environment. Mechanisms of toxicity are still poorly understood although it seems clear that in some cases nanoscale specific properties may cause biouptake and toxicity over and above that caused by the dissolved Ag ion. This review concludes with a set of recommendations for the advancement of understanding of the role of nanoscale silver in environmental and ecotoxicological research.     

Estimation of radon exhalation rate, natural radioactivity and radiation doses in fly ash samples from Durgapur thermal power plant, West Bengal, India

Coal and its by products often contain significant amounts of radionuclides, including uranium which is the ultimate source of the radioactive gas radon. Burning of coal and the subsequent emission to the atmosphere cause the re-distribution of toxic trace elements in the environment. Due to considerable economic and environmental importance and diverse uses, the collected fly ash has become a subject of worldwide interest in recent years. In the present study, radon exhalation rate and the activity concentration of (238)U, (232)Th and (40)K radionuclides in fly ash samples from Durgapur thermal power plant (WB) have been measured by "Sealed Can technique" using LR-115 type II detectors and a low level NaI (Tl) based gamma ray spectrometer, respectively. Radon exhalation rate varied from 360.0 to 470.0 mBq m(-2)h(-1) with an average value of 406.8 mBq m(-2)h(-1). Activity concentrations of (238)U ranged from 84.8 to 126.4 Bq kg(-1) with an average value of 99.3Bqkg(-1), (232)Th ranged from 98.1 to 140.5 Bq kg(-1) with an average value of 112.9 Bq kg(-1) and (40)K ranged from 267.1 to 364.9 Bq kg(-1) with an average value of 308.9 Bq kg(-1). Radium equivalent activity obtained from activity concentrations is found to vary from 256.5 to 352.8 Bq kg(-1) with an average value of 282.5 Bq kg(-1). Absorbed gamma dose rates due to the presence of (238)U, (232)Th and (40)K in fly ash samples vary in the range 115.3-158.5 nGy h(-1) with an average value of 126.4 nGy h(-1). While the external annual effective dose rate varies from 0.14 to 0.19 mSv y(-1) with an average value of 0.15 mSv y(-1), effective dose equivalent estimated from exhalation rate varies from 42.5 to 55.2 microSv y(-1) with an average value of 47.8 microSv y(-1). Values of external hazard index H(ex) for the fly ash samples studied in this work range from 0.69 to 0.96 with a mean value of 0.77.     

Determination of concentration factors for Cs-137 and Ra-226 in the mullet species Chelon labrosus (Mugilidae) from the South Adriatic Sea

Concentration factors for Cs-137 and Ra-226 transfer from seawater, and dried sediment or mud with detritus, have been determined for whole, fresh weight, Chelon labrosus individuals and selected organs. Cesium was detected in 5 of 22 fish individuals, and its activity ranged from 1.0 to 1.6 Bq kg⁻¹. Radium was detected in all fish, and ranged from 0.4 to 2.1 Bq kg⁻¹, with an arithmetic mean of 1.0 Bq kg⁻¹. In regards to fish organs, cesium activity concentration was highest in muscles (maximum - 3.7 Bq kg⁻¹), while radium was highest in skeletons (maximum - 25 Bq kg⁻¹). Among cesium concentration factors, those for muscles were the highest (from seawater - an average of 47, from sediment - an average of 3.3, from mud with detritus - an average of 0.8). Radium concentration factors were the highest for skeleton (from seawater - an average of 130, from sediment - an average of 1.8, from mud with detritus - an average of 1.5). Additionally, annual intake of cesium and radium by human adults consuming muscles of this fish species has been estimated to provide, in aggregate, an effective dose of about 4.1 μSv y⁻¹.     

Sector field inductively coupled plasma mass spectrometry, another tool for plutonium isotopes and plutonium isotope ratios determination in environmental matrices

The transfer of radio nuclides into the different compartments of the environment are widely studied and leads to the elaboration of transfer models in order to evaluate potential impact onto the environment and humans. Accurate experimental data are needed to validate these models for all types of matrices (air, water, sediments, soils, biota and food...). Among these radionuclides, 238Pu, 239Pu, 240Pu and 241Pu, are often mentioned. They have been released into the environment by nuclear weapon tests, nuclear facilities, reactors or satellite accidents. These different sources have different 240Pu/239Pu ratios and therefore this ratio is used to provide information on the source of contamination into the environment. The most conventional analytical tools used for plutonium isotope determination are liquid scintillation and alpha spectrometry, and thermal ionisation mass spectrometry (TIMS) is still considered as the primary method for determination of plutonium isotope ratios. During the last decade, mass spectrometers equipped with plasma ion sources and sector field analysers were developed and can offer now another alternative method for the accurate determination of isotope content and ratios of long-lived radionuclides in environmental samples. This paper presents and discusses the results obtained for 239Pu, 240Pu and 241Pu content and isotope ratios by sector field ICP-MS in different environmental matrices.     

Triclosan in waste and surface waters from the upper Detroit River by liquid chromatography-electrospray-tandem quadrupole mass spectrometry

Triclosan (5-chloro-2-(2,4-dichlorophenoxy)phenol) is an antimicroibial disinfectant agent used in a wide array of consumer products. An analytical method based on solid-phase extraction (SPE) followed by reverse phase, liquid chromatography coupled with electrospray ionization (negative)-tandem quadrupole mass spectrometry (LC-ESI(-)-MS/MS; in the multiple reaction monitoring (MRM) mode) was developed, optimized and validated for the determination of triclosan in wastewater/sewage treatment plant (WSTP) effluent and surface waters from the upper Detroit River (Canada). The mean recoveries (+/-%RSD) of triclosan and the internal standard 2'-HO-tribromodiphenyl ether (2'-HO-BDE-28) spiked to surface water and WSTP effluent samples ranged similarly from 104+/-8% and 91+/-10%, respectively, and method limits of quantification were in the low ppb/high ppt range. However, ESI(-) enhancement was found for both analytes due to sample matrix effects, as indicated by % process efficiencies (a measure of ESI(-) enhancement/suppression), which were in the 111-128% range. We report the first known assessment of triclosan in the Detroit River watershed of the Great Lakes, which preliminarily examined the presence and UV-treatment effects on triclosan in effluent from the major WSTP serving the City of Windsor, Ontario, Canada, and fate in surface waters of the upper Detroit River. Triclosan in WSTP effluent decreased 22% after final UV treatment to a mean concentration of 63 ng/L. Concentrations were further reduced to 4 and 8 ng/L (a >90% reduction) in surface water samples from sites downstream on the Canadian shoreline of the Detroit River, which was due to dilution. Two hydroxylated tribrominated diphenyl ethers, which are structurally similar to triclosan, were also detected in WSTP effluent and surface water samples.     

Exploitation of renewable energy resources for environment‐friendly sustainable development in Saudi Arabia

The recent increase in energy costs, driven by a surge in oil prices, has increased world‐wide efforts on the exploitation of renewable/wind energy resources for environment‐friendly sustainable development and to mitigate future energy challenges. Moreover, experience in the wind energy industry has reached high levels in the field of manufacturing and application. This inevitably increases the merits of wind energy exploitation. In order to exploit wind resources, through the establishment of wind power plants, specific attention must be focused on the characteristics of wind and wind machines. The literature indicates that wind‐energy resources are relatively better along coastlines. In the present study, long‐term hourly mean wind speed data for the period 1986–2003, recorded at Dhahran (Eastern Coastal region, Saudi Arabia), has been analysed to examine the wind characteristics including (but not limited to): yearly/monthly/diurnal variations of wind speed, frequency distribution of wind speed, impact of hub‐height/machine‐size on energy production, etc. Data have been checked/validated for completeness. Data analysis indicated that long‐term monthly average wind speeds ranged from 3.8 to 5.8 m/s.

Concurrently, the study determined monthly average daily energy generation from different sizes of commercial wind machines (150, 250, 600 kW, etc.) to assess the impact of wind machine size on energy yield. The study also estimated annual energy production (MWh/year) from wind farms of different capacities (3, 6, 12, 24 MW, etc.) by utilising different commercial wind energy conversion systems (WECS). It was observed that, for a given 6 MW wind farm size, a cluster of 150 kW wind machines (at 50 m hub‐height) yielded about 32% more energy when compared to a cluster of 600 kW wind machines. The study also estimated the cost of wind‐based electricity (COE, US$/kWh) by using different capacities of commercial WECS. It was found that the COE per kWh is 0.045 US$/kWh for 150 kW wind machine (at 50 m hub‐height) whereas COE was 0.039 US$/kWh for 600 kW wind machine (at 50 m hub‐height). The study also dealt with wind turbine characteristics (such as capacity factor and availability factor). These characteristics are important indicators of wind turbine performance evaluation.     

Cosmogenic 22Na as an index of the residence time of water in freshwater basins: a review

The goal of this review is to draw attention to an opportunity for the use of cosmogenic (22)Na for dating young surface and underground waters. After 1961 when a significant quantity of (22)Na was released into the environment as a result of nuclear weapon tests, its concentrations in river waters were greatly increased, and a return to natural (cosmogenic) levels took until the mid-1980s. The studies made during this non-steady-state period showed that the one-box model for freshwater basin correctly describes the experimental data. For the 19 studied basins of Russia, the Baltic States and Japan, a calculation based on this model gave values for the mean residence time of water in the range from 4 to 23 years. Now, only cosmogenic (22)Na is in the environment, and it is the single cosmogenic radionuclide at present, which can serve as a steady-state tracer for dating young waters (up to some decades).     

Studies of Np and Pu in the marine environment of Swedish-Danish waters and the North Atlantic Ocean

The long-lived anthropogenic radionuclides (237)Np, (239)Pu and (240)Pu were determined in marine environmental samples (seaweed and seawater) collected from Swedish-Danish waters and the North Atlantic Ocean at various locations on different occasions during the period 1991-2001. The measurements were performed with sector field Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and conventional alpha spectrometry. The (237)Np activity concentrations in Fucus vesiculosus and surface seawater from the Swedish west coast and Danish waters ranged from 0.16+/-0.02 to 1.02+/-0.09 mBq kg(-1) (dry weight) and 0.65+/-0.02 to 1.69+/-0.02 mBq m(-3), respectively, depending on the location and sampling year. Most of the (237)Np in these waters is believed to originate from the Sellafield nuclear reprocessing plant, with some contribution from global fallout. The (240)Pu/(239)Pu atomic ratios in F. vesiculosus samples are reported in this study with an overall average of 0.17+/-0.03. The (237)Np and (239)Pu activity concentrations observed in surface seawater collected in North Atlantic waters ranged from 0.16+/-0.01 to 0.62+/-0.08 mBq m(-3) and from 0.64+/-0.05 to 4.27+/-0.08 mBq m(-3), respectively, and the (237)Np/(239)Pu atomic ratios were a good indicator of conservative behaviour of Np in marine waters.