The combined effects of biomass and temperature on maximum specific ammonia oxidation rate in domestic wastewater treatment

• Actual SAORs was determined using MLVSS and temperature. • Measured SAOR decreased with increasing MLVSS 1.1‒8.7 g/L. • Temperature coefficient (θ) decreased with increasing MLVSS. • Nitrification process was dynamically simulated based on laboratory-scale SBR tests. • A modified model was successfully validated in pilot-scale SBR systems. Measurement and predicted variations of ammonia oxidation rate (AOR) are critical for the optimization of biological nitrogen removal, however, it is difficult to predict accurate AOR based on current models. In this study, a modified model was developed to predict AOR based on laboratory-scale tests and verified through pilot-scale tests. In biological nitrogen removal reactors, the specific ammonia oxidation rate (SAOR) was affected by both mixed liquor volatile suspended solids (MLVSS) concentration and temperature. When MLVSS increased 1.6, 4.2, and 7.1-fold (1.3‒8.9 g/L, at 20°C), the measured SAOR decreased by 21%, 49%, and 56%, respectively. Thereby, the estimated SAOR was suggested to modify when MLVSS changed through a power equation fitting. In addition, temperature coefficient (θ) was modified based on MLVSS concentration. These results suggested that the prediction of variations ammonia oxidation rate in real wastewater treatment system could be more accurate when considering the effect of MLVSS variations on SAOR.     

Nitrate removal to its fate in wetland mesocosm filled with sponge iron: Impact of influent COD/N ratio

• CW-Fe allowed a high-performance of NO₃^‒-N removal at the COD/N ratio of 0. • Higher COD/N resulted in lower chem-denitrification and higher bio-denitrification. • The application of s-Fe⁰ contributed to TIN removal in wetland mesocosm. • s-Fe⁰ changed the main denitrifiers in wetland mesocosm. Sponge iron (s-Fe⁰) is a porous metal with the potential to be an electron donor for denitrification. This study aims to evaluate the feasibility of using s-Fe⁰ as the substrate of wetland mesocosms. Here, wetland mesocosms with the addition of s-Fe⁰ particles (CW-Fe) and a blank control group (CW-CK) were established. The NO₃^‒-N reduction property and water quality parameters (pH, DO, and ORP) were examined at three COD/N ratios (0, 5, and 10). Results showed that the NO₃^‒-N removal efficiencies were significantly increased by 6.6 to 58.9% in the presence of s-Fe⁰. NH₄⁺-N was mainly produced by chemical denitrification, and approximately 50% of the NO₃^‒-N was reduced to NH₄⁺-N, at the COD/ratio of 0. An increase of the influent COD/N ratio resulted in lower chemical denitrification and higher bio-denitrification. Although chemical denitrification mediated by s-Fe⁰ led to an accumulation of NH₄⁺-N at COD/N ratios of 0 and 5, the TIN removal efficiencies increased by 4.5%‒12.4%. Moreover, the effluent pH, DO, and ORP values showed a significant negative correlation with total Fe and Fe (II) (P<0.01). High-throughput sequencing analysis indicated that Trichococcus (77.2%) was the most abundant microorganism in the CW-Fe mesocosm, while Thauera, Zoogloea, and Herbaspirillum were the primary denitrifying bacteria. The denitrifiers, Simplicispira, Dechloromonas, and Denitratisoma, were the dominant bacteria for CW-CK. This study provides a valuable method and an improved understanding of NO₃^‒-N reduction characteristics of s-Fe⁰ in a wetland mesocosm.     

Quantification of emission variability for off-road equipment in China based on real-world measurements

• Emissions from 53 in-use diesel-fueled off-road equipment were measured. • There exists a large off-road equipment variability in emissions. • Engine operations have significant impacts on real-world tailpipe emissions. • Emission inventory development should take into account job duties and operations. The objective of this paper is to quantify the variability in emissions of off-road equipment using a portable emission measurement system. A total of 53 commonly used equipment for agriculture, base construction, paving construction, and material handling were selected. Time-based and fuel-based emissions were quantified by different duty and engine modes. Three duty modes (idling, moving, and working) were used. Ten engine modes were defined based on normalized engine revolutions-per-minute and manifold absolute pressure, respectively. Composite emission factors taking into account both duty modes and its corresponding time percentage during a typical duty cycle were estimated. Results showed that there existed a large off-road equipment variability in emissions. Depending on duty and engine modes, time-based NO emissions ranged from 3.1 to 237.9, 29.1‒1475.6, 83.2‒681.6, and 3.2‒385.2 g/h for agriculture, base construction, paving construction and material handling equipment, respectively while for fuel-based NO emissions these ranges were 5.3‒52.0, 11.7‒69.0, 4.8‒30.8, and 11.0‒54.6 g/kg, respectively. Furthermore, emission factors derived from this study exhibited a much larger variability compared to those used in NONROAD by US EPA and National Guideline for Off-road Equipment of China. This implied that localized measurements of emissions are needed for improvement of accuracy of emission inventory. Furthermore, both equipment types and operations should be considered for development of emission inventory and control strategy.     

Quantification of pesticide residues on plastic mulching films in typical farmlands of the North China

• Pesticide residuals on mulching film of Shandong, Tianjin and Hebei. • Detected 29 pesticides in soil and 30 in mulching film. • Pesticides on plastic films: 86.4‒22213.2 ng/g and in soil: 9.3‒535.3 ng/g. • Pesticides on plastic films 20 times higher than in soil. Plastic debris as new pollutants attracts much attention in the recent years. The plastic mulching films is one of the most important plastic debirs source in the environment. The aim of this work was to investigate the current status of pesticide residues on the plastic mulching films. Based on the QuEChERS method, multi-residue methods for detection of pesticide residues with gas chromatography tandem mass spectrum (GC-MS) and high performance liquid chromatography tandem mass spectrum (HPLC-MS) were developed for the analysis of the pesticides residues in plastic film and soil samples from Tianjin, Hebei and Shandong. The total concentrations of pesticide residues were in the range of 86.4‒22213.2 ng/g in plastic film debris, which was about 20 times higher than that in soil (9.3‒535.3 ng/g). Residual level of pesticides varied greatly in different samples. The historical usage and recent application of pesticides were the main sources for pesticide residues on plastic films and soil. In short, plastic mulching films could act as a sink for pesticides in farmland and the ubiquitous pesticide residues on plastic films should draw more attention.     

An integrated method for the rapid dewatering and solidification/stabilization of dredged contaminated sediment with a high water content

• An integrated method, called PHDVPSS, was proposed for treating DCS. • The PHDVPSS method showed superior performance compared to conventional method. • Using the method, water content (%) of DCS decreased from 300 to<150 in 3 days. • The 56-day UCS from this method is 12‒17 times higher than conventional method. • Relative to PC, GGBS-MgO binder yielded greater reduction in the leachability. To more efficiently treat the dredged contaminated sediment (DCS) with a high water content, this study proposes an integrated method (called PHDVPSS) that uses the solidifying/stabilizing (S/S) agents and prefabricated horizontal drain (PHD) assisted by vacuum pressure (VP). Using this method, dewatering and solidification/stabilization can be carried out simultaneously such that the treatment time can be significantly shortened and the treatment efficacy can be significantly improved. A series of model tests was conducted to investigate the effectiveness of the proposed method. Experimental results indicated that the proposed PHDVPSS method showed superior performance compared to the conventional S/S method that uses Portland cement (PC) directly without prior dewatering. The 56-day unconfined compressive strength of DCS treated by the proposed method with GGBS-MgO as the binder is 12‒17 times higher than that by the conventional S/S method. DCS treated by the PHDVPSS method exhibited continuous decrease in leaching concentration of Zn with increasing curing age. The reduction of Zn leachability is more obvious when using GGBS-MgO as the binder than when using PC, because GGBS-MgO increased the residual fraction and decreased the acid soluble fraction of Zn. The microstructure analysis reveals the formation of hydrotalcite in GGBS-MgO binder, which resulted in higher mechanical strength and higher Zn stabilization efficiency.     

TiO2@palygorskite composite for the efficient remediation of oil spills via a dispersion-photodegradation synergy

• A novel and multi-functional clay-based oil spill remediation system was constructed. • TiO₂@PAL functions as a particulate dispersant to break oil slick into tiny droplets. • Effective dispersion leads to the direct contact of TiO₂ with oil pollutes directly. • TiO₂ loaded on PAL exhibits efficient photodegradation for oil pollutants. • TiO₂@PAL shows a typical dispersion-photocatalysis synergistic remediation. Removing spilled oil from the water surface is critically important given that oil spill accidents are a common occurrence. In this study, TiO₂@Palygorskite composite prepared by a simple coprecipitation method was used for oil spill remediation via a dispersion-photodegradation synergy. Diesel could be efficiently dispersed into small oil droplets by TiO₂@Palygorskite. These dispersed droplets had an average diameter of 20–30 mm and exhibited good time stability. The tight adsorption of TiO₂@Palygorskite on the surface of the droplets was observed in fluorescence and SEM images. As a particulate dispersant, the direct contact of TiO₂@Palygorskite with oil pollutants effectively enhanced the photodegradation efficiency of TiO₂ for oil. During the photodegradation process, •O₂⁻and •OH were detected by ESR and radical trapping experiments. The photodegradation efficiency of diesel by TiO₂@Palygorskite was enhanced by about 5 times compared with pure TiO₂ under simulated sunlight irradiation. The establishment of this new dispersion-photodegradation synergistic remediation system provides a new direction for the development of marine oil spill remediation.     

Cultivation of Chlorella sp. HQ in inland saline-alkaline water under different light qualities

• Optimal growth of Chlorella in inland saline-alkaline water was achieved by blue LED. • Lipids of Chlorella sp. HQ were mainly composed of C16:0 and C18:2 under various LEDs. • The BiodieselAnalyzer^© software was used to evaluate the Chlorella biodiesel quality. • Chlorella sp. HQ was a high-quality feedstock for biodiesel production. Inland saline-alkaline water can be used for the low-cost cultivation of microalgae, but whether algal biomass under various light sources has the potential to produce biodiesel remains to be developed. Herein, the influence of different light-emitting diode (LEDs) light colors (blue, red, white, mixed blue-red, and mixed blue-white LED) on the growth performance, lipid accumulation, and fatty acid composition of Chlorella sp. HQ cultivated in inland saline-alkaline water was investigated. The highest algal density was obtained under blue LEDs at the end of cultivation, reaching 1.93±0.03 × 10⁷ cells/mL. White LEDs can improve biomass yield, total lipid yield, and triacylglycerol yield per algal cell. The main fatty acid components of Chlorella from inland saline-alkaline water were palmitic acid and linoleic acid. The BiodieselAnalyzer^© software was used to predict algal biodiesel quality by estimating different quality parameters. The cetane number, kinematic viscosity, and density of Chlorella biodiesel were 51.714–67.69, 3.583–3.845 mm²/s, and 0.834–0.863 g/cm³, respectively. This further proved that the Chlorella biomass obtained from inland saline-alkaline water has the potential to be used as a high-quality biodiesel feedstock.     

Formation of disinfection by-products during sodium hypochlorite cleaning of fouled membranes from membrane bioreactors

•HAAs was dominant among the DBPs of interest. •Rising time, dose, temperature and pH raised TCM and HAAs but reduced HANs and HKs. •Low time, dose and temperature and non-neutrality pH reduced toxic risks of DBPs. •The presence of EPS decelerated the production of DBPs. •EPS, particularly polysaccharides were highly resistant to chlorine. Periodic chemical cleaning with sodium hypochlorite (NaClO) is essential to restore the membrane permeability in a membrane bioreactor (MBR). However, the chlorination of membrane foulants results in the formation of disinfection by-products (DBPs), which will cause the deterioration of the MBR effluent and increase the antibiotic resistance in bacteria in the MBR tank. In this study, the formation of 14 DBPs during chemical cleaning of fouled MBR membrane modules was investigated. Together with the effects of biofilm extracellular polymeric substances (EPS), influences of reaction time, NaClO dosage, initial pH, and cleaning temperature on the DBP formation were investigated. Haloacetic acids (HAAs) and trichloromethane (TCM), composed over 90% of the DBPs, were increasingly accumulated as the NaClO cleaning time extended. By increasing the chlorine dosage, temperature, and pH, the yield of TCM and dichloroacetic acid (DCAA) was increased by up to a factor of 1‒14, whereas the yields of haloacetonitriles (HANs) and haloketones (HKs) were decreased. Either decreasing in the chlorine dosage and cleaning temperature or adjusting the pH of cleaning reagents toward acidic or alkaline could effectively reduce the toxic risks caused by DBPs. After the EPS extraction pretreatment, the formation of DBPs was accelerated in the first 12 h due to the damage of biofilm structure. Confocal laser scanning microscopy (CLSM) images showed that EPS, particularly polysaccharides, were highly resistant to chlorine and might be able to protect the cells exposed to chlorination.     

Membrane-based treatment of shale oil and gas wastewater: The current state of knowledge

• Shale oil and gas production generates wastewater with complex composition. • Membrane technologies emerged for the treatment of shale oil and gas wastewater. • Membrane technologies should tolerate high TDS and consume low primary energy. • Pretreatment is a key component of integrated wastewater treatment systems. • Full-scale implementation of membrane technologies is highly desirable. Shale oil and gas exploitation not only consumes substantial amounts of freshwater but also generates large quantities of hazardous wastewater. Tremendous research efforts have been invested in developing membrane-based technologies for the treatment of shale oil and gas wastewater. Despite their success at the laboratory scale, membrane processes have not been implemented at full scale in the oil and gas fields. In this article, we analyze the growing demands of wastewater treatment in shale oil and gas production, and then critically review the current stage of membrane technologies applied to the treatment of shale oil and gas wastewater. We focus on the unique niche of those technologies due to their advantages and limitations, and use mechanical vapor compression as the benchmark for comparison. We also highlight the importance of pretreatment as a key component of integrated treatment trains, in order to improve the performance of downstream membrane processes and water product quality. We emphasize the lack of sufficient efforts to scale up existing membrane technologies, and suggest that a stronger collaboration between academia and industry is of paramount importance to translate membrane technologies developed in the laboratory to the practical applications by the shale oil and gas industry.     

Microplastics removal strategies: A step toward finding the solution

• Physical, chemical and biological methods are explored for MPs removal. • Physical methods based on adsorption/filtration are mostly used for MPs removal. • Chemical methods of MPs removal work on coagulation and flocculation mechanism. • MBR technology has also shown the removal of MPs from water. • Global policy on plastic control is lacking. Microplastics are an emerging threat and a big challenge for the environment. The presence of microplastics (MPs) in water is life-threatening to diverse organisms of aquatic ecosystems. Hence, the scientific community is exploring deeper to find treatment and removal options of MPs. Various physical, chemical and biological methods are researched for MPs removal, among which few have shown good efficiency in the laboratory. These methods also have a few limitations in environmental conditions. Other than finding a suitable method, the creation of legal restrictions at a governmental level by imposing policies against MPs is still a daunting task in many countries. This review is an effort to place all effectual MP removal methods in one document to compare the mechanisms, efficiency, advantages, and disadvantages and find the best solution. Further, it also discusses the policies and regulations available in different countries to design an effective global policy. Efforts are also made to discuss the research gaps, recent advancements, and insights in the field.     

Repercussions of COVID-19 pandemic on solid waste generation and management strategies

• Implication of COVID-19 on medical waste and MSW generation is studied. • Challenges and effective strategy of solid waste generation is reviewed. • 2.9 million tons of COVID-19 related medical waste has been generated until Sep. 22. • The pandemic has postponed policies related to the reduction of plastic use. • Blockade resulted in a significant drop in waste generation in some regions. It has been over ten months since the beginning of the 2019 coronavirus disease (COVID-2019), and its impact on solid waste management, especially medical waste, is becoming clearer. This study systematically reviews the potential influences of the COVID-19 pandemic on medical waste, personal protection equipment waste and municipal solid waste (MSW), and discusses the corresponding measures and policies of solid waste management in typical countries. The results show that the generation of medical waste from the pandemic increased significantly, with 18%‒425% growth. It is estimated that the daily output of COVID-19 medical waste increased from 200 t/d on Feb. 22 to over 29000 t/d at the end of September 2020 throughout the world. The use of personal protective equipment will continue to grow in the long-term, while the blockade and isolation measures greatly reduced the volume of commercial waste, especially for tourist cities, and part of this waste was transferred to household waste. Residents’ attitudes and behavior toward food waste have changed due to the COVID-19 pandemic. In response to the pandemic, international organizations and several countries have issued new policies and guidelines and adjusted their management strategies for medical waste and MSW treatment. The pandemic has brought specific challenges to the disposal capacity of medical waste worldwide. It has also brought about the stagnation of policies related to the reduction of plastic products and waste recycling. This study will provide some useful information for managers and governmental officials on effective solid waste management during and after the COVID-19 pandemic.     

Sulfur cycle as an electron mediator between carbon and nitrate in a constructed wetland microcosm

• Fe(III) accepted the most electrons from organics, followed by NO₃^‒, SO₄^2‒, and O₂. • The electrons accepted by SO₄^2‒ could be stored in the solid AVS, FeS₂-S, and S⁰. • The autotrophic denitrification driven by solid S had two-phase characteristics. • A conceptual model involving electron acceptance, storage, and donation was built. • S cycle transferred electrons between organics and NO₃^‒ with an efficiency of 15%. A constructed wetland microcosm was employed to investigate the sulfur cycle-mediated electron transfer between carbon and nitrate. Sulfate accepted electrons from organics at the average rate of 0.84 mol/(m³·d) through sulfate reduction, which accounted for 20.0% of the electron input rate. The remainder of the electrons derived from organics were accepted by dissolved oxygen (2.6%), nitrate (26.8%), and iron(III) (39.9%). The sulfide produced from sulfate reduction was transformed into acid-volatile sulfide, pyrite, and elemental sulfur, which were deposited in the substratum, storing electrons in the microcosm at the average rate of 0.52 mol/(m³·d). In the presence of nitrate, the acid-volatile and elemental sulfur were oxidized to sulfate, donating electrons at the average rate of 0.14 mol/(m³·d) and driving autotrophic denitrification at the average rate of 0.30 g N/(m³·d). The overall electron transfer efficiency of the sulfur cycle for autotrophic denitrification was 15.3%. A mass balance assessment indicated that approximately 50% of the input sulfur was discharged from the microcosm, and the remainder was removed through deposition (49%) and plant uptake (1%). Dominant sulfate-reducing (i.e., Desulfovirga, Desulforhopalus, Desulfatitalea, and Desulfatirhabdium) and sulfur-oxidizing bacteria (i.e., Thiohalobacter, Thiobacillus, Sulfuritalea, and Sulfurisoma), which jointly fulfilled a sustainable sulfur cycle, were identified. These results improved understanding of electron transfers among carbon, nitrogen, and sulfur cycles in constructed wetlands, and are of engineering significance.     

Size and shape effects of MnFe2O4 nanoparticles as catalysts for reductive degradation of dye pollutants

• Size and shape-dependent MnFe₂O₄ NPs were prepared via a facile method. • Ligand-exchange chemistry was used to prepare the hydrophilic MnFe₂O₄ NPs. • The catalytic properties of MnFe₂O₄ NPs toward dye degradation were fully studied. • The catalytic activities of MnFe₂O₄ NPs followed Michaelis–Menten behavior. • All the MnFe₂O₄ NPs exhibit selective degradation to different dyes. The magnetic nanoparticles that are easy to recycle have tremendous potential as a suitable catalyst for environmental toxic dye pollutant degradation. Rationally engineering shapes and tailoring the size of nanocatalysts are regarded as an effective manner for enhancing performances. Herein, we successfully synthesized three kinds of MnFe₂O₄ NPs with distinctive sizes and shapes as catalysts for reductive degradation of methylene blue, rhodamine 6G, rhodamine B, and methylene orange. It was found that the catalytic activities were dependent on the size and shape of the MnFe₂O₄ NPs and highly related to the surface-to-volume ratio and atom arrangements. Besides, all these nanocatalysts exhibit selectivity to different organic dyes, which is beneficial for their practical application in dye pollutant treatment. Furthermore, the MnFe₂O₄ NPs could be readily recovered by a magnet and reused more than ten times without appreciable loss of activity. The size and shape effects of MnFe₂O₄ nanoparticles demonstrated in this work not only accelerate further understanding the nature of nanocatalysts but also contribute to the precise design of nanoparticles catalyst for pollutant degradation.     

Submerged arc plasma system combined with ozone oxidation for the treatment of wastewater containing non-degradable organic compounds

• Submerged arc plasma was introduced in terms of wastewater treatment. • Ozone oxidation was coupled with submerged arc plasma system. • Ozone was converted into O and O₂ by submerged arc plasma. • Decomposition rate was accelerated by submerged arc plasma. • Introduction of ozone led to significant increase in mineralization. Submerged arc plasma technology was assessed for the removal of phenols from wastewater. The OH radicals generated from the boundary between the plasma and waste solution were considered as a significant factor on the degradation reaction. In this study, the effects of highly energetic electrons released from the submerged arc plasma were mainly studied. The highly energetic electrons directly broke the strong chemical bond and locally increased the reaction temperatures in solution. The effects of the submerged-arc plasma on the decomposition of phenol are discussed in terms of the input energy and initial concentration. The single use of submerged arc plasma easily decomposed the phenol but did not increase the mineralization efficiency. Therefore, the submerged arc plasma, coupled with the ozone injection, was investigated. The submerged arc plasma combined with ozone injection had a synergic effect, which led to significant improvements in mineralization with only a small increase in input energy. The decomposition mechanism of phenol by the submerged arc plasma with the ozone was analyzed.     

Bacteriophages in water pollution control: Advantages and limitations

•Phages can be better indicators of enteric viruses than fecal indicator bacteria. •Multiple phages should be added to the microbial source tracking toolbox. •Engineered phage or phage cocktail can effectively target resistant bacteria. •In phage use, phage-mediated horizontal gene transfer cannot be ignored. •More schemes are needed to prevent phage concentration from decreasing. Wastewater is a breeding ground for many pathogens, which may pose a threat to human health through various water transmission pathways. Therefore, a simple and effective method is urgently required to monitor and treat wastewater. As bacterial viruses, bacteriophages (phages) are the most widely distributed and abundant organisms in the biosphere. Owing to their capacity to specifically infect bacterial hosts, they have recently been used as novel tools in water pollution control. The purpose of this review is to summarize and evaluate the roles of phages in monitoring pathogens, tracking pollution sources, treating pathogenic bacteria, infecting bloom-forming cyanobacteria, and controlling bulking sludge and biofilm pollution in wastewater treatment systems. We also discuss the limitations of phage usage in water pollution control, including phage-mediated horizontal gene transfer, the evolution of bacterial resistance, and phage concentration decrease. This review provides an integrated outlook on the use of phages in water pollution control.     

Influences and mechanisms of nanofullerene on the horizontal transfer of plasmid-encoded antibiotic resistance genes between E. coli strains

• Sub-inhibitory levels of nC₆₀ promote conjugative transfer of ARGs. • nC₆₀ can induce ROS generation, oxidative stress and SOS response. • nC₆₀ can increase cell membrane permeability and alter gene expression. • Results provide evidence of nC₆₀ promoting antibiotic resistance dissemination. The spread and development of antibiotic resistance globally have led to severe public health problems. It has been shown that some non-antibiotic substances can also promote the diffusion and spread of antibiotic resistance genes (ARGs). Nanofullerene (nC₆₀) is a type of nanomaterial widely used around the world, and some studies have discovered both the biological toxicity and environmental toxicity of nC₆₀. In this study, cellular and molecular biology techniques were employed to investigate the influences of nC₆₀ at sub-minimum inhibitory concentrations (sub-MICs) on the conjugation of ARGs between the E. coli strains. Compared with the control group, nC₆₀ significantly increased the conjugation rates of ARGs by 1.32‒10.82 folds within the concentration range of 7.03‒1800 mg/L. This study further explored the mechanism of this phenomenon, finding that sub-MICs of nC₆₀ could induce the production of reactive oxygen species (ROS), trigger SOS-response and oxidative stress, affect the expression of outer membrane proteins (OMPs) genes, increase membrane permeability, and thus promote the occurrence of conjugation. This research enriches our understanding of the environmental toxicity of nC₆₀, raises our risk awareness toward nC₆₀, and may promote the more rational employment of nC₆₀ materials.     

Valorization of agro-industrial fruit peel waste to fluorescent nanocarbon sensor: Ultrasensitive detection of potentially hazardous tropane alkaloid

• Transformation of agro-industrial waste to value-added material via green chemistry. • Orange peel is valorized into fluorescent nanodiamond-like carbon (fNDC) sensor. • fNDC detects potentially hazardous drug atropine sulfate (AS). • fNDC recognizes AS in biological fluids and pharmaceuticals. • fNDC assures applications in clinical and forensic toxicology. Millions of tonnes of agro-industrial waste are generated each year globally, with the vast majority of it going untreated, underutilized, and disposed of by burning or landfilling, causing severe environmental distress and economic downturn. A practical solution to this global issue is to use green chemistry to convert this waste into value-added products. Accordingly, in the present study, agro-industrial orange peel waste was valorized into fluorescent nanodiamond-like carbon sensor via a green route involving hydrothermal treatment of microwave carbonized orange peel waste. The developed sensor, used for the fluorescence detection of potentially hazardous drug atropine sulfate, exhibits unique dual linearity over concentration ranges of 300 nM to 1 M and from 1 M to 10 M, as well as ultra-low sensitivity of 34.42 nM and 356.46 nM, respectively. Additionally, the sensor demonstrates excellent reproducibility, high stability, and satisfactory recovery when used to identify and quantify atropine sulfate in biological samples and commercially available pharmaceuticals, indicating promising multidisciplinary applications.     

Response of bioaerosol cells to photocatalytic inactivation with ZnO and TiO2 impregnated onto Perlite and Poraver carriers

•ZnO/Perlite inactivated 72% of bioaerosols in continuous gas phase. •TiO₂ triggered the highest level of cytotoxicity with 95% dead cells onto Poraver. •Inactivation mechanism occurred by membrane damage, morphological changes and lysis. •ZnO/Poraver showed null inactivation of bioaerosols. •Catalysts losses at the outlet of the photoreactor for all systems were negligible. Bioaerosols are airborne microorganisms that cause infectious sickness, respiratory and chronic health issues. They have become a latent threat, particularly in indoor environment. Photocatalysis is a promising process to inactivate completely bioaerosols from air. However, in systems treating a continuous air flow, catalysts can be partially lost in the gaseous effluent. To avoid such phenomenon, supporting materials can be used to fix catalysts. In the present work, four photocatalytic systems using Perlite or Poraver glass beads impregnated with ZnO or TiO₂ were tested. The inactivation mechanism of bioaerosols and the cytotoxic effect of the catalysts to bioaerosols were studied. The plug flow photocatalytic reactor treated a bioaerosol flow of 460×1 0⁶ cells/m³_air with a residence time of 5.7 s. Flow Cytometry (FC) was used to quantify and characterize bioaerosols in terms of dead, injured and live cells. The most efficient system was ZnO/Perlite with 72% inactivation of bioaerosols, maintaining such inactivation during 7.5 h due to the higher water retention capacity of Perlite (2.8 mL/g_Perlite) in comparison with Poraver (1.5 mL/g_Perlite). However, a global balance showed that TiO₂/Poraver system triggered the highest level of cytotoxicity to bioaerosols retained on the support after 96 h with 95% of dead cells. SEM and FC analyses showed that the mechanism of inactivation with ZnO was based on membrane damage, morphological cell changes and cell lysis; whereas only membrane damage and cell lysis were involved with TiO₂. Overall, results highlighted that photocatalytic technologies can completely inactivate bioaerosols in indoor environments.     

One-step ball milling-prepared nano Fe2O3 and nitrogen-doped graphene with high oxygen reduction activity and its application in microbial fuel cells

• Nano Fe₂O₃ and N-doped graphene was prepared via a one-step ball milling method. • The maximum power density of Fe-N-G in MFC was 390% of that of pristine graphite. • Active sites like nano Fe₂O₃, pyridinic N and Fe-N groups were formed in Fe-N-G. • The improvement of Fe-N-G was due to full exposure of active sites on graphene. Developing high activity, low-cost and long durability catalysts for oxygen reduction reaction is of great significance for the practical application of microbial fuel cells. The full exposure of active sites in catalysts can enhance catalytic activity dramatically. Here, novel Fe-N-doped graphene is successfully synthesized via a one-step in situ ball milling method. Pristine graphite, ball milling graphene, N-doped graphene and Fe-N-doped graphene are applied in air cathodes, and enhanced performance is observed in microbial fuel cells with graphene-based catalysts. Particularly, Fe-N-doped graphene achieves the highest oxygen reduction reaction activity, with a maximum power density of 1380±20 mW/m² in microbial fuel cells and a current density of 23.8 A/m² at –0.16 V in electrochemical tests, which are comparable to commercial Pt and 390% and 640% of those of pristine graphite. An investigation of the material characteristics reveals that the superior performance of Fe-N-doped graphene results from the full exposure of Fe₂O₃ nanoparticles, pyrrolic N, pyridinic N and excellent Fe-N-G active sites on the graphene matrix. This work not only suggests the strategy of maximally exposing active sites to optimize the potential of catalysts but also provides promising catalysts for the use of microbial fuel cells in sustainable energy generation.     

Review on remediation technologies for arsenic-contaminated soil

• Recent progress of As-contaminated soil remediation technologies is presented. • Phytoextraction and chemical immobilization are the most widely used methods. • Novel remediation technologies for As-contaminated soil are still urgently needed. • Methods for evaluating soil remediation efficiency are lacking. • Future research directions for As-contaminated soil remediation are proposed. Arsenic (As) is a top human carcinogen widely distributed in the environment. As-contaminated soil exists worldwide and poses a threat on human health through water/food consumption, inhalation, or skin contact. More than 200 million people are exposed to excessive As concentration through direct or indirect exposure to contaminated soil. Therefore, affordable and efficient technologies that control risks caused by excess As in soil must be developed. The presently available methods can be classified as chemical, physical, and biological. Combined utilization of multiple technologies is also common to improve remediation efficiency. This review presents the research progress on different remediation technologies for As-contaminated soil. For chemical methods, common soil washing or immobilization agents were summarized. Physical technologies were mainly discussed from the field scale. Phytoextraction, the most widely used technology for As-contaminated soil in China, was the main focus for bioremediation. Method development for evaluating soil remediation efficiency was also summarized. Further research directions were proposed based on literature analysis.