Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Precise regulation of acid pretreatment for red mud SCR catalyst: Targeting on optimizing the acidity and reducibility

• The optimum SCR activity was realized by tuning the acid pretreatment. • Optimized catalysts showed NO_x conversion above 90%. • The NH₃ and NO adsorption capacity of Al-O₃-Fe is stronger than Fe-O₃-Fe. • The formation of almandine consumes Fe³⁺ and Al³⁺ and weakens their interaction. Red mud (RM), as an alkaline waste, was recently proved to be a promising substitute for the SCR catalyst. Dealkalization could improve the acidity and reducibility of red mud, which were critical for SCR reaction. However, the dealkalization effect depended on the reaction between acid solution and red mud. In this study, we realized the directional control of the chemical state of active sites through tuning the acid pretreatment (dealkalization) process. The pretreatment endpoint was controlled at pH values of 3–5 with diluted nitric acid. When the pH values of red mud were 3 and 5 (CRM-3 and CRM-5), activated catalysts showed NO_x conversion above 90% at 275°C–475°C. The high initial reaction rate, Ce³⁺/(Ce³⁺ + Ce⁴⁺) ratio, and surface acidity accounted for the excellent SCR performance of CRM-5 catalyst. Meanwhile, more Fe³⁺ on the CRM-3 surface improved the NH₃ adsorption. There was a strong interaction between Al and Fe in both CRM-5 and CRM-3 catalysts. DFT results showed that the adsorption capacity of the Al-O₃-Fe for NH₃ and NO is stronger than that of Fe-O₃-Fe, which enhanced the NO_x conversion of the catalyst. However, the almandine was formed in CRM-4, consumed part of Fe³⁺ and Al³⁺, and the interaction between Al and Fe was weakened. Also, deposited almandine on the catalyst surface covered the active sites, thus leading to lower NH₃-SCR activity.     

Nitrate removal to its fate in wetland mesocosm filled with sponge iron: Impact of influent COD/N ratio

• CW-Fe allowed a high-performance of NO₃^‒-N removal at the COD/N ratio of 0. • Higher COD/N resulted in lower chem-denitrification and higher bio-denitrification. • The application of s-Fe⁰ contributed to TIN removal in wetland mesocosm. • s-Fe⁰ changed the main denitrifiers in wetland mesocosm. Sponge iron (s-Fe⁰) is a porous metal with the potential to be an electron donor for denitrification. This study aims to evaluate the feasibility of using s-Fe⁰ as the substrate of wetland mesocosms. Here, wetland mesocosms with the addition of s-Fe⁰ particles (CW-Fe) and a blank control group (CW-CK) were established. The NO₃^‒-N reduction property and water quality parameters (pH, DO, and ORP) were examined at three COD/N ratios (0, 5, and 10). Results showed that the NO₃^‒-N removal efficiencies were significantly increased by 6.6 to 58.9% in the presence of s-Fe⁰. NH₄⁺-N was mainly produced by chemical denitrification, and approximately 50% of the NO₃^‒-N was reduced to NH₄⁺-N, at the COD/ratio of 0. An increase of the influent COD/N ratio resulted in lower chemical denitrification and higher bio-denitrification. Although chemical denitrification mediated by s-Fe⁰ led to an accumulation of NH₄⁺-N at COD/N ratios of 0 and 5, the TIN removal efficiencies increased by 4.5%‒12.4%. Moreover, the effluent pH, DO, and ORP values showed a significant negative correlation with total Fe and Fe (II) (P<0.01). High-throughput sequencing analysis indicated that Trichococcus (77.2%) was the most abundant microorganism in the CW-Fe mesocosm, while Thauera, Zoogloea, and Herbaspirillum were the primary denitrifying bacteria. The denitrifiers, Simplicispira, Dechloromonas, and Denitratisoma, were the dominant bacteria for CW-CK. This study provides a valuable method and an improved understanding of NO₃^‒-N reduction characteristics of s-Fe⁰ in a wetland mesocosm.     

Remediation of 2,4-dichlorophenol-contaminated groundwater using nano-sized CaO2 in a two-dimensional scale tank

• Nano CaO₂ is evaluated as a remediation agent for 2,4-DCP contaminated groundwater. • 2,4-DCP degradation mechanism by different Fe²⁺ concentration was proposed. • 2,4-DCP was not degraded in the system for solution pH>10. • The 2,4-DCP degradation area is inconsistent with the nano CaO₂ distribution area. This study evaluates the applicability of nano-sized calcium peroxide (CaO₂) as a source of H₂O₂ to remediate 2,4-dichlorophenol (2,4-DCP) contaminated groundwater via the advanced oxidation process (AOP). First, the effect and mechanism of 2,4-DCP degradation by CaO₂ at different Fe concentrations were studied (Fenton reaction). We found that at high Fe concentrations, 2,4-DCP almost completely degrades via primarily the oxidation of •OH within 5 h. At low Fe concentrations, the degradation rate of 2,4-DCP decreased rapidly. The main mechanism was the combined action of •OH and O₂^•−. Without Fe, the 2,4-DCP degradation reached 13.6% in 213 h, primarily via the heterogeneous reaction on the surface of CaO₂. Besides, 2,4-DCP degradation was significantly affected by solution pH. When the solution pH was>10, the degradation was almost completely inhibited. Thus, we adopted a two-dimensional water tank experiment to study the remediation efficiency CaO₂ on the water sample. We noticed that the degradation took place mainly in regions of pH<10 (i.e., CaO₂ distribution area), both upstream and downstream of the tank. After 28 days of treatment, the average 2,4-DCP degradation level was ≈36.5%. Given the inadequacy of the results, we recommend that groundwater remediation using nano CaO₂: (1) a buffer solution should be added to retard the rapid increase in pH, and (2) the nano CaO₂ should be injected copiously in batches to reduce CaO₂ deposition.     

Sulfur cycle as an electron mediator between carbon and nitrate in a constructed wetland microcosm

• Fe(III) accepted the most electrons from organics, followed by NO₃^‒, SO₄^2‒, and O₂. • The electrons accepted by SO₄^2‒ could be stored in the solid AVS, FeS₂-S, and S⁰. • The autotrophic denitrification driven by solid S had two-phase characteristics. • A conceptual model involving electron acceptance, storage, and donation was built. • S cycle transferred electrons between organics and NO₃^‒ with an efficiency of 15%. A constructed wetland microcosm was employed to investigate the sulfur cycle-mediated electron transfer between carbon and nitrate. Sulfate accepted electrons from organics at the average rate of 0.84 mol/(m³·d) through sulfate reduction, which accounted for 20.0% of the electron input rate. The remainder of the electrons derived from organics were accepted by dissolved oxygen (2.6%), nitrate (26.8%), and iron(III) (39.9%). The sulfide produced from sulfate reduction was transformed into acid-volatile sulfide, pyrite, and elemental sulfur, which were deposited in the substratum, storing electrons in the microcosm at the average rate of 0.52 mol/(m³·d). In the presence of nitrate, the acid-volatile and elemental sulfur were oxidized to sulfate, donating electrons at the average rate of 0.14 mol/(m³·d) and driving autotrophic denitrification at the average rate of 0.30 g N/(m³·d). The overall electron transfer efficiency of the sulfur cycle for autotrophic denitrification was 15.3%. A mass balance assessment indicated that approximately 50% of the input sulfur was discharged from the microcosm, and the remainder was removed through deposition (49%) and plant uptake (1%). Dominant sulfate-reducing (i.e., Desulfovirga, Desulforhopalus, Desulfatitalea, and Desulfatirhabdium) and sulfur-oxidizing bacteria (i.e., Thiohalobacter, Thiobacillus, Sulfuritalea, and Sulfurisoma), which jointly fulfilled a sustainable sulfur cycle, were identified. These results improved understanding of electron transfers among carbon, nitrogen, and sulfur cycles in constructed wetlands, and are of engineering significance.     

The size distribution of airborne bacteria and human pathogenic bacteria in a commercial composting plant

•Bacterial concentrations from eight stages were 10⁴–10⁵copies/m³. •Diameter influenced clustering of bacterial and HPB lineages. •Dg of 8 HPB ranged from 2.42 to 5.09 μm in composting areas. •Dg of 8 HPB ranged from 3.70 to 8.96 μm in packaging areas. •HPB had high concentrations and small sizes in composting areas. Composting plants are regarded as one of the important sources of environmental bioaerosols. However, limitations in the size distribution of airborne bacteria have prevented our comprehensive understanding of their risk to human health and their dispersal behavior. In this study, different sizes of airborne bacteria were collected using an eight-stage impactor from a full-scale composting facility. Size-related abundance and communities of airborne bacteria as well as human pathogenic bacteria (HPB) were investigated using 16S rRNA gene sequencing coupled with droplet digital PCR. Our results indicate that the bacterial concentrations from the eight stages were approximately 10⁴–10⁵copies/m³. Although no statistical correlation was detected between the particle size and the Shannon index, the influence of size on bacterial lineages was observed in both composting and packaging areas. For airborne bacteria from different stages, the dominant phyla were Firmicutes, Proteobacteria, and Actinobacteria, and the dominant genera was Bacillus. Seven out of eight HPB with a small geometric mean aerodynamic diameter had a high concentration in composting areas. Based on diameters of 2.42 to 5.09 μm, most HPB in the composting areas were expected to be deposited on the bronchus and secondary bronchus. However, in the packaging areas, the deposition of HPB (diameters 3.70 to 8.96 μm) occurred in the upper part of the respiratory tract. Our results on the size distribution, abundance, and diversity of these bacteria offer important information for the systematic evaluation of bacterial pathogenicity and the potential health impacts on workers in composting plants and the surrounding residents.     

Visible-light-driven heterostructured g-C3N4/Bi-TiO2 floating photocatalyst with enhanced charge carrier separation for photocatalytic inactivation of Microcystis aeruginosa

• Bi doping in TiO₂ enhanced the separation of photo-generated electron-hole. • The performance of photocatalytic degradation of MC-LR was improved. • Coexisting substances have no influence on algal removal performance. • The key reactive oxygen species were h⁺ and ^•OH in the photocatalytic process. The increase in occurrence and severity of cyanobacteria blooms is causing increasing concern; moreover, human and animal health is affected by the toxic effects of Microcystin-LR released into the water. In this paper, a floating photocatalyst for the photocatalytic inactivation of the harmful algae Microcystis aeruginosa (M. aeruginosa) was prepared using a simple sol-gel method, i.e., coating g-C₃N₄ coupled with Bi-doped TiO₂ on Al₂O₃-modified expanded perlite (CBTA for short). The impact of different molar ratios of Bi/Ti on CBTA was considered. The results indicated that Bi doping in TiO₂ inhibited photogenerated electron-hole pair recombination. With 6 h of visible light illumination, 75.9% of M. aeruginosa (initial concentration= 2.7 × 10⁶ cells/L) and 83.7% of Microcystin-LR (initial concentration= 100 μg/L) could be removed with the addition of 2 g/L CBTA-1% (i.e., Bi/Ti molar ratio= 1%). The key reactive oxygen species (ROSs) in the photocatalytic inactivation process are h⁺ and ^•OH. The induction of the Bi⁴⁺/Bi³⁺ species by the incorporation of Bi could narrow the bandgap of TiO₂, trap electrons, and enhance the stability of CBTA-1% in the solutions with coexisting environmental substances.     

Response of bioaerosol cells to photocatalytic inactivation with ZnO and TiO2 impregnated onto Perlite and Poraver carriers

•ZnO/Perlite inactivated 72% of bioaerosols in continuous gas phase. •TiO₂ triggered the highest level of cytotoxicity with 95% dead cells onto Poraver. •Inactivation mechanism occurred by membrane damage, morphological changes and lysis. •ZnO/Poraver showed null inactivation of bioaerosols. •Catalysts losses at the outlet of the photoreactor for all systems were negligible. Bioaerosols are airborne microorganisms that cause infectious sickness, respiratory and chronic health issues. They have become a latent threat, particularly in indoor environment. Photocatalysis is a promising process to inactivate completely bioaerosols from air. However, in systems treating a continuous air flow, catalysts can be partially lost in the gaseous effluent. To avoid such phenomenon, supporting materials can be used to fix catalysts. In the present work, four photocatalytic systems using Perlite or Poraver glass beads impregnated with ZnO or TiO₂ were tested. The inactivation mechanism of bioaerosols and the cytotoxic effect of the catalysts to bioaerosols were studied. The plug flow photocatalytic reactor treated a bioaerosol flow of 460×1 0⁶ cells/m³_air with a residence time of 5.7 s. Flow Cytometry (FC) was used to quantify and characterize bioaerosols in terms of dead, injured and live cells. The most efficient system was ZnO/Perlite with 72% inactivation of bioaerosols, maintaining such inactivation during 7.5 h due to the higher water retention capacity of Perlite (2.8 mL/g_Perlite) in comparison with Poraver (1.5 mL/g_Perlite). However, a global balance showed that TiO₂/Poraver system triggered the highest level of cytotoxicity to bioaerosols retained on the support after 96 h with 95% of dead cells. SEM and FC analyses showed that the mechanism of inactivation with ZnO was based on membrane damage, morphological cell changes and cell lysis; whereas only membrane damage and cell lysis were involved with TiO₂. Overall, results highlighted that photocatalytic technologies can completely inactivate bioaerosols in indoor environments.     

Optimization of the O3/H2O2 process with response surface methodology for pretreatment of mother liquor of gas field wastewater

• Real ML-GFW with high salinity and high organics was degraded by O₃/H₂O₂ process. • Successful optimization of operation conditions was attained using RSM based on CCD. • Single-factor experiments in advance ensured optimal experimental conditions. • The satisfactory removal efficiency of TOC was achieved in spite of high salinity. • The initial pH plays the most significant role in the degradation of ML-GFW. The present study reports the use of the O₃/H₂O₂ process in the pretreatment of the mother liquor of gas field wastewater (ML-GFW), obtained from the multi-effect distillation treatment of the gas field wastewater. The range of optimal operation conditions was obtained by single-factor experiments. Response surface methodology (RSM) based on the central composite design (CCD) was used for the optimization procedure. A regression model with Total organic carbon (TOC) removal efficiency as the response value was established (R² = 0.9865). The three key factors were arranged according to their significance as: pH>H₂O₂ dosage>ozone flow rate. The model predicted that the best operation conditions could be obtained at a pH of 10.9, an ozone flow rate of 0.8 L/min, and H₂O₂ dosage of 6.2 mL. The dosing ratio of ozone was calculated to be 9.84 mg O₃/mg TOC. The maximum removal efficiency predicted was 75.9%, while the measured value was 72.3%. The relative deviation was found to be in an acceptable range. The ozone utilization and free radical quenching experiments showed that the addition of H₂O₂ promoted the decomposition of ozone to produce hydroxyl radicals (·OH). This also improved the ozone utilization efficiency. Gas chromatography-mass spectrometry (GC-MS) analysis showed that most of the organic matters in ML-GFW were degraded, while some residuals needed further treatment. This study provided the data and the necessary technical supports for further research on the treatment of ML-GFW.     

A Cu-modified active carbon fiber significantly promoted H2S and PH3 simultaneous removal at a low reaction temperature

• Cu_0.15-ACF performs the best for H₂S and PH₃ simultaneous removal. • 550°C and 90°C are separately calcination and reaction temperatures. • The reason why Cu_0.15/ACF shows better performance was found. • The accumulation of H₂PO₄⁻ and SO₄²⁻(H₂O)₆ is the deactivation cause of Cu_0.15/ACF. Poisonous gases, such as H₂S and PH₃, produced by industrial production harm humans and damage the environment. In this study, H₂S and PH₃ were simultaneously removed at low temperature by modified activated carbon fiber (ACF) catalysts. We have considered the active metal type, content, precursor, calcination, and reaction temperature. Experimental results exhibited that ACF could best perform by loading 15% Cu from nitrate. The optimized calcination temperature and reaction temperature separately were 550°C and 90°C. Under these conditions, the most removal capacity could reach 69.7 mg/g and 132.1 mg/g, respectively. Characterization results showed that moderate calcination temperature (550°C) is suitable for the formation of the copper element on the surface of ACF, lower or higher temperature will generate more cuprous oxide. Although both can exhibit catalytic activity, the role of the copper element is significantly greater. Due to the exceptional dispersibility of copper (oxide), the ACF can still maintain the advantages of larger specific surface area and pore volume after loading copper, which is the main reason for better performance of related catalysts. Finally, increasing the copper loading amount can significantly increase the crystallinity and particle size of copper (oxide) on the ACF, thereby improving its catalytic performance. In situ IR found that the reason for the deactivation of the catalyst should be the accumulation of generated H₂PO₄⁻ and SO₄²⁻(H₂O)₆ which could poison the catalyst.     

Partial anammox achieved in full scale biofilm process for typical domestic wastewater treatment

• A full scale biofilm process was developed for typical domestic wastewater treatment. • The HRT was 8 h and secondary sedimentation tank was omitted. • Candidatus Brocadia were enriched in the HBR with an abundance of 2.89%. • Anammox enabled a stable ammonium removal of ~15% in the anoxic zone. The slow initiation of anammox for treating typical domestic wastewater and the relatively high footprint of wastewater treatment infrastructures are major concerns for practical wastewater treatment systems. Herein, a 300 m³/d hybrid biofilm reactor (HBR) process was developed and operated with a short hydraulic retention time (HRT) of 8 h. The analysis of the bacterial community demonstrated that anammox were enriched in the anoxic zone of the HBR process. The percentage abundance of Candidatus Brocadia in the total bacterial community of the anoxic zone increased from 0 at Day 1 to 0.33% at Day 130 and then to 2.89% at Day 213. Based upon the activity of anammox bacteria, the removal of ammonia nitrogen (NH₄⁺-N) in the anoxic zone was approximately 15%. This showed that the nitrogen transformation pathway was enhanced in the HBR system through partial anammox process in the anoxic zone. The final effluent contained 12 mg/L chemical oxygen demand (COD), 0.662 mg/L NH₄⁺-N, 7.2 mg/L total nitrogen (TN), and 6 mg/L SS, indicating the effectiveness of the HBR process for treating real domestic wastewater.     

A heterotrophic nitrification-aerobic denitrification bacterium Halomonas venusta TJPU05 suitable for nitrogen removal from high-salinity wastewater

• H. venusta TJPU05 showed excellent HN-AD ability at high salinity. • Successful expression of AMO, HAO, NAR and NIR confirmed the HN-AD ability of TJPU05. • H. venusta TJPU05 could tolerate high salt and high nitrogen environment. • H. venusta TJPU05 is a promising candidate for the bio-treatment of AW. A novel salt-tolerant heterotrophic nitrification and aerobic denitrification (HN-AD) bacterium was isolated and identified as Halomonas venusta TJPU05 (H. venusta TJPU05). The nitrogen removal performance of H. venusta TJPU05 in simulated water (SW) with sole or mixed nitrogen sources and in actual wastewater (AW) with high concentration of salt and nitrogen was investigated. The results showed that 86.12% of NH₄⁺-N, 95.68% of NO₃^–-N, 100% of NO₂^–-N and 84.57% of total nitrogen (TN) could be removed from SW with sole nitrogen sources within 24 h at the utmost. H. venusta TJPU05 could maximally remove 84.06% of NH₄⁺-N, 92.33% of NO₃^–-N, 92.9% of NO₂^–-N and 77.73% of TN from SW with mixed nitrogen source when the salinity was above 8%. The application of H. venusta TJPU05 in treating AW with high salt and high ammonia nitrogen led to removal efficiencies of 50.96%, 47.28% and 43.19% for NH₄⁺-N, NO₃^–-N and TN respectively without any optimization. Furthermore, the activities of nitrogen removal–related enzymes of the strain were also investigated. The successful detection of high level activities of ammonia oxygenase (AMO), hydroxylamine oxidase (HAO), nitrate reductase (NAR) and nitrite reductase (NIR) enzymes under high salinity condition further proved the HN-AD and salt-tolerance capacity of H. venusta TJPU05. These results demonstrated that the H. venusta TJPU05 has great potential in treating high-salinity nitrogenous wastewater.     

Assessment of mobile and potential mobile trace elements extractability in calcareous soils using different extracting agents

• DTPA and NH₄OAc, HNO₃ and EDTA, and MgCl₂ and NH₄NO₃ had similar behavior. • In NH₄OAc, DTPA, and EDTA, the possibility of re-adsorption of trace elements is low. • CaCl₂ may be more suitable than other extracts in calcareous soils. Understanding trace elements mobility in soils, extracting agents, and their relationships with soil components, are essential for predicting their movement in soil profile and availability to plants. A laboratory study was conducted to evaluate extractability of cadmium (Cd), cobalt (Co), copper (Cu), nickel (Ni), and zinc (Zn) from calcareous soils utilizing various extracting agents to be specific CaCl₂, DTPA, EDTA, HNO₃, MgCl₂, NaNO₃, NH₄NO₃, and NH₄OAc. Cluster analysis indicated that DTPA and NH₄OAc, HNO₃ and EDTA, and MgCl₂ and NH₄NO₃ extracting agents yielded comparative values, whereas NaNO₃ and CaCl₂ have shown different behavior than other extracting agents for all studied trace elements. The speciation of extracted trace elements in solutions indicated that in the CaCl₂, NaNO₃, NH₄NO₃, and MgCl₂ extracting agents most extracted Cd, Co, Ni, Zn, and part of Cu were as free ions and may be re-adsorbed on soils, leading to lower extractability, whereas, in the case of HNO₃ extracting agent, the likelihood of re-adsorption of trace elements may be little. The results of speciation of trace elements using NH₄OAc, DTPA, and EDTA extracting agents showed that Me-(Acetate)₃^–, Me-(Acetate)₂(aq), Me(DTPA)³⁻, Me(EDTA)²⁻, and MeH(EDTA)^– complexes dominated in solutions indicating that the extracted trace elements may not be re-adsorbed on soils, leading to higher extractability. The results of this study are useful for short and long-term evaluations of trace elements mobility and further environmental impacts.     

Evaluation of the technoeconomic feasibility of electrochemical hydrogen peroxide production for decentralized water treatment

• Gas diffusion electrode (GDE) is a suitable setup for practical water treatment. • Electrochemical H₂O₂ production is an economically competitive technology. • High current efficiency of H₂O₂ production was obtained with GDE at 5–400 mA/cm². • GDE maintained high stability for H₂O₂ production for ~1000 h. • Electro-generation of H₂O₂ enhances ibuprofen removal in an E-peroxone process. This study evaluated the feasibility of electrochemical hydrogen peroxide (H₂O₂) production with gas diffusion electrode (GDE) for decentralized water treatment. Carbon black-polytetrafluoroethylene GDEs were prepared and tested in a continuous flow electrochemical cell for H₂O₂ production from oxygen reduction. Results showed that because of the effective oxygen transfer in GDEs, the electrode maintained high apparent current efficiencies (ACEs,>80%) for H₂O₂ production over a wide current density range of 5–400 mA/cm², and H₂O₂ production rates as high as ~202 mg/h/cm² could be obtained. Long-term stability test showed that the GDE maintained high ACEs (>85%) and low energy consumption (<10 kWh/kg H₂O₂) for H₂O₂ production for 42 d (~1000 h). However, the ACEs then decreased to ~70% in the following 4 days because water flooding of GDE pores considerably impeded oxygen transport at the late stage of the trial. Based on an electrode lifetime of 46 days, the overall cost for H₂O₂ production was estimated to be ~0.88 $/kg H₂O₂, including an electricity cost of 0.61 $/kg and an electrode capital cost of 0.27 $/kg. With a 9 cm² GDE and 40 mA/cm² current density, ~2–4 mg/L of H₂O₂ could be produced on site for the electro-peroxone treatment of a 1.2 m³/d groundwater flow, which considerably enhanced ibuprofen abatement compared with ozonation alone (~43%–59% vs. 7%). These findings suggest that electrochemical H₂O₂ production with GDEs holds great promise for the development of compact treatment technologies for decentralized water treatment at a household and community level.     

Forward osmosis coupled with lime-soda ash softening for volume minimization of reverse osmosis concentrate and CaCO3 recovery: A case study on the coal chemical industry

• Forward osmosis (FO) coupled with chemical softening for CCI ROC minimization • Effective removal of scale precursor ions by lime-soda ash softening • Enhanced water recovery from 54% to 86% by mitigation of FO membrane scaling • High-purity CaCO₃ was recovered from the softening sludge • Membrane cleaning efficiency of 88.5% was obtained by EDTA for softened ROC Reverse osmosis (RO) is frequently used for water reclamation from treated wastewater or desalination plants. The RO concentrate (ROC) produced from the coal chemical industry (CCI) generally contains refractory organic pollutants and extremely high-concentration inorganic salts with a dissolved solids content of more than 20 g/L contributed by inorganic ions, such as Na⁺, Ca²⁺, Mg²⁺, Cl⁻, and SO₄²⁻. To address this issue, in this study, we focused on coupling forward osmosis (FO) with chemical softening (FO-CS) for the volume minimization of CCI ROC and the recovery of valuable resources in the form of CaCO₃. In the case of the real raw CCI ROC, softening treatment by lime-soda ash was shown to effectively remove Ca²⁺/Ba²⁺ (>98.5%) and Mg²⁺/Sr²⁺/Si (>80%), as well as significantly mitigate membrane scaling during FO. The softened ROC and raw ROC corresponded to a maximum water recovery of 86% and 54%, respectively. During cyclic FO tests (4 × 10 h), a 27% decline in the water flux was observed for raw ROC, whereas only 4% was observed for softened ROC. The cleaning efficiency using EDTA was also found to be considerably higher for softened ROC (88.5%) than that for raw ROC (49.0%). In addition, CaCO₃ (92.2% purity) was recovered from the softening sludge with an average yield of 5.6 kg/m³ treated ROC. This study provides a proof-of-concept demonstration of the FO-CS coupling process for ROC volume minimization and valuable resources recovery, which makes the treatment of CCI ROC more efficient and more economical.     

Removal of ammonium and nitrate through Anammox and FeS-driven autotrophic denitrification

● Simultaneous NH₄⁺/NO₃^– removal was achieved in the FeS denitrification system ● Anammox coupled FeS denitrification was responsible for NH₄⁺/NO₃^– removal ● Sulfammox, Feammox and Anammox occurred for NH₄⁺ removal ● Thiobacillus, Nitrospira , and Ca. Kuenenia were key functional microorganisms An autotrophic denitrifying bioreactor with iron sulfide (FeS) as the electron donor was operated to remove ammonium (NH₄⁺) and nitrate (NO₃⁻) synergistically from wastewater for more than 298 d. The concentration of FeS greatly affected the removal of NH₄⁺/NO₃⁻. Additionally, a low hydraulic retention time worsened the removal efficiency of NH₄⁺/NO₃⁻. When the hydraulic retention time was 12 h, the optimal removal was achieved with NH₄⁺ and NO₃⁻ removal percentages both above 88%, and the corresponding nitrogen removal loading rates of NH₄⁺ and NO₃⁻ were 49.1 and 44.0 mg/(L·d), respectively. The removal of NH₄⁺ mainly occurred in the bottom section of the bioreactor through sulfate/ferric reducing anaerobic ammonium oxidation (Sulfammox/Feammox), nitrification, and anaerobic ammonium oxidation (Anammox) by functional microbes such as Nitrospira, Nitrosomonas, and Candidatus Kuenenia. Meanwhile, NO₃⁻ was mainly removed in the middle and upper sections of the bioreactor through autotrophic denitrification by Ferritrophicum, Thiobacillus, Rhodanobacter, and Pseudomonas, which possessed complete denitrification-related genes with high relative abundances.     

The performance of nitrate-reducing Fe(II) oxidation processes under variable initial Fe/N ratios: The fate of nitrogen and iron species

•Bacterially-mediated coupled N and Fe processes examined in incubation experiments. •NO₃⁻ reduction was considerably inhibited as initial Fe/N ratio increased. •The maximum production of N₂ occurred at an initial Fe/N molar ratio of 6. •Fe minerals produced at Fe/N ratios of 1–2 were mainly easily reducible oxides. The Fe/N ratio is an important control on nitrate-reducing Fe(II) oxidation processes that occur both in the aquatic environment and in wastewater treatment systems. The response of nitrate reduction, Fe oxidation, and mineral production to different initial Fe/N molar ratios in the presence of Paracoccus denitrificans was investigated in 132 h incubation experiments. A decrease in the nitrate reduction rate at 12 h occurred as the Fe/N ratio increased. Accumulated nitrite concentration at Fe/N ratios of 2–10 peaked at 12–84 h, and then decreased continuously to less than 0.1 mmol/L at the end of incubation. N₂O emission was promoted by high Fe/N ratios. Maximum production of N₂ occurred at a Fe/N ratio of 6, in parallel with the highest mole proportion of N₂ resulting from the reduction of nitrate (81.2%). XRD analysis and sequential extraction demonstrated that the main Fe minerals obtained from Fe(II) oxidation were easily reducible oxides such as ferrihydrite (at Fe/N ratios of 1–2), and easily reducible oxides and reducible oxides (at Fe/N ratios of 3–10). The results suggest that Fe/N ratio potentially plays a critical role in regulating N₂, N₂O emissions and Fe mineral formation in nitrate-reducing Fe(II) oxidation processes.     

Four kinds of capping materials for controlling phosphorus and nitrogen release from contaminated sediment using a static simulation experiment

• Lanthanum modified bentonite (LMB) can effectively absorb phosphorus (P). • Water treatment plant sludge (WTPS) capping is effective for controlling P release. •Aluminum-based P-inactivation agent (Al-PIA) is an efficient P control material. •The P adsorbed by WTPS and Al-PIA is mainly in the form of NAIP. We determined the effects of quartz sand (QS), water treatment plant sludge (WTPS), aluminum-based P-inactivation agent (Al-PIA), and lanthanum-modified bentonite (LMB) thin-layer capping on controlling phosphorus and nitrogen release from the sediment, using a static simulation experiment. The sediment in the experiment was sampled from Yundang Lagoon (Xiamen, Fujian Province, China), which is a eutrophic waterbody. The total phosphorus (TP), ammonium nitrogen (NH₄⁺-N), and total organic carbon (TOC) levels in the overlying water were measured at regular intervals, and the changes of different P forms in WTPS, Al-PIA, and sediment of each system were analyzed before and after the test. The average TP reduction rates of LMB, Al-PIA, WTPS, and QS were 94.82, 92.14, 86.88, and 10.68%, respectively, when the release strength of sediment TP was 2.26–9.19 mg/(m²·d) and the capping strength of the materials was 2 kg/m². Thin-layer capping of LMB, WTPS, and Al-PIA could effectively control P release from the sediment (P<0.05). However, thin-layer capping of LMB, Al-PIA, and QS did not significantly reduce the release of ammonium N and organic matter (P > 0.05). Based on our results, LMB, Al-PIA, and WTPS thin-layer capping promoted the migration and transformation of easily released P in sediment. The P adsorbed by WTPS and Al-PIA mainly occurred in the form of NAIP.     

TiO2@palygorskite composite for the efficient remediation of oil spills via a dispersion-photodegradation synergy

• A novel and multi-functional clay-based oil spill remediation system was constructed. • TiO₂@PAL functions as a particulate dispersant to break oil slick into tiny droplets. • Effective dispersion leads to the direct contact of TiO₂ with oil pollutes directly. • TiO₂ loaded on PAL exhibits efficient photodegradation for oil pollutants. • TiO₂@PAL shows a typical dispersion-photocatalysis synergistic remediation. Removing spilled oil from the water surface is critically important given that oil spill accidents are a common occurrence. In this study, TiO₂@Palygorskite composite prepared by a simple coprecipitation method was used for oil spill remediation via a dispersion-photodegradation synergy. Diesel could be efficiently dispersed into small oil droplets by TiO₂@Palygorskite. These dispersed droplets had an average diameter of 20–30 mm and exhibited good time stability. The tight adsorption of TiO₂@Palygorskite on the surface of the droplets was observed in fluorescence and SEM images. As a particulate dispersant, the direct contact of TiO₂@Palygorskite with oil pollutants effectively enhanced the photodegradation efficiency of TiO₂ for oil. During the photodegradation process, •O₂⁻and •OH were detected by ESR and radical trapping experiments. The photodegradation efficiency of diesel by TiO₂@Palygorskite was enhanced by about 5 times compared with pure TiO₂ under simulated sunlight irradiation. The establishment of this new dispersion-photodegradation synergistic remediation system provides a new direction for the development of marine oil spill remediation.     

A novel strategy for gas mitigation during swine manure odour treatment using seaweed and a microbial consortium

• Comprehensive mitigation of gas emissions from swine manure was investigated. • Additives addition for mitigation of gas from the manure has been developed. • Sargassum horneri, seaweed masking strategy controlled gas by 90%-100%. • Immediate reduction in emitted gas and improving air quality has been determined. • Microbial consortium with seaweed completely controlled gas emissions by 100%. Gas emissions from swine farms have an impact on air quality in the Republic of Korea. Swine manure stored in deep pits for a long time is a major source of harmful gas emissions. Therefore, we evaluated the mitigation of emissions of ammonia (NH₃), hydrogen sulfide (H₂S) and amine gases from swine manure with biological products such as seaweed (Sargassum horneri) and a microbial consortium (Bacillus subtilis (1.2 × 10⁹ CFU/mL), Thiobacillus sp. (1.0 × 10¹⁰ CFU/mL) and Saccharomyces cerevisiae (2.0 × 10⁹ CFU/mL)) used as additives due to their promising benefits for nutrient cycling. Overall, seaweed powder masking over two days provided notable control of over 98%-100% of the gas emissions. Furthermore, significant control of gas emissions was especially pronounced when seaweed powder masking along with a microbial consortium was applied, resulting in a gas reduction rate of 100% for NH₃, amines and H₂S over 10 days of treatment. The results also suggested that seaweed powder masking and a microbial consortium used in combination to reduce the gas emissions from swine manure reduced odour compared with that observed when the two additives were used alone. Without the consortium, seaweed decreased total volatile fatty acid (VFA) production. The proposed novel method of masking with a microbial consortium is promising for mitigating hazardous gases, simple, and environmentally beneficial. More research is warranted to determine the mechanisms underlying the seaweed and substrate interactions.