Hexavalent chromium in drinking water: Chemistry,challenges and future outlook on Sn(II)- and photocatalyst-based treatment

• Wide occurrence of Cr(VI) in US source drinking water. • A strong dependence of occurrence on groundwater sources. • Elucidate Redox and equilibrium chemistry of Cr(VI). • Sn(II)-based and TiO₂-based reductive treatments hold extreme promise. • Key challenges include residual waste, Cr(VI) re-generation and socioeconomic drivers. Chromium (Cr) typically exists in either trivalent and hexavalent oxidation states in drinking water, i.e., Cr(III) and Cr(VI), with Cr(VI) of particular concern in recent years due to its high toxicity and new regulatory standards. This Account presented a critical analysis of the sources and occurrence of Cr(VI) in drinking water in the United States, analyzed the equilibrium chemistry of Cr(VI) species, summarized important redox reaction relevant to the fate of Cr(VI) in drinking water, and critically reviewed emerging Cr(VI) treatment technologies. There is a wide occurrence of Cr(VI) in US source drinking water, with a strong dependence on groundwater sources, mainly due to naturally weathering of chromium-containing aquifers. Challenges regarding traditional Cr(VI) treatment include chemical cost, generation of secondary waste and inadvertent re-generation of Cr(VI) after treatment. To overcome these challenges, reductive Cr(VI) treatment technologies based on the application of stannous tin or electron-releasing titanium dioxide photocatalyst hold extreme promise in the future. To moving forward in the right direction, three key questions need further exploration for the technology implementation, including effective management of residual waste, minimizing the risks of Cr(VI) re-occurrence downstream of drinking water treatment plant, and promote the socioeconomic drivers for Cr(VI) control in the future.     

Product identification and toxicity change during oxidation of methotrexate by ferrate and permanganate in water

• Oxidation of methotrexate by high-valent metal-oxo species was first explored. • Fe(VI) presented a higher reactivity to MTX than Mn(VII) at pH 8.0. • Ketonization and cleavage of peptide bond were two initial reaction pathways. • Products of MTX were not genotoxic, neurotoxic, or endocrine-disrupting chemicals. • The less biodegradable products exhibited developmental and acute/chronic toxicity. Accompanying an annual increase in cancer incidence, the global use of anticancer drugs has remarkably increased with their worldwide environmental prevalence and ecological risks. In this study, the oxidation of methotrexate (MTX), a typical anticancer drug with ubiquitous occurrence and multi-endpoint toxicity, by ferrate(VI) (Fe(VI)) and permanganate (Mn(VII))) was investigated in water. Fe(VI) exhibited a higher reactivity with MTX (93.34 M⁻¹ s⁻¹) than Mn(VII) (3.01 M⁻¹ s⁻¹) at pH 8.0. The introduction of Cu(II) and Fe(III) at 1.0 mM improved the removal efficiency of 5.0 μM MTX by 100.0 μM Fe(VI) from 80% to 95% and 100% after 4 min, respectively. Seven oxidized products (OPs) were identified during oxidative treatments, while OP-191 and OP-205 were characterized as specific products for Fe(VI) oxidation. Initial ketonization of the L-glutamic acid moiety and cleavage of the peptide bond of MTX were proposed. Additionally, a multi-endpoint toxicity evaluation indicated no genotoxicity, neurotoxicity, or endocrine-disrupting effects of MTX and its OPs. Particularly, serious developmental toxicity in zebrafish larvae was observed in the treated MTX solutions. Based on the acute and chronic aquatic toxicity prediction, OP-190, OP-192, OP-206, and OP-208 were deemed toxic or very toxic compared to harmful MTX. Furthermore, the reduced biodegradability index from 0.15 (MTX) to −0.5 to −0.2 (OP-192, OP-206, and OP-468) indicated the formation of lower biodegradable OPs. Overall, this study suggests that Fe(VI) and Mn(VII) oxidation are promising treatments for remediating anticancer drug-contaminated water. However, the environmental risks associated with these treatments should be considered in the evaluation of water safety.     

Review on remediation technologies for arsenic-contaminated soil

• Recent progress of As-contaminated soil remediation technologies is presented. • Phytoextraction and chemical immobilization are the most widely used methods. • Novel remediation technologies for As-contaminated soil are still urgently needed. • Methods for evaluating soil remediation efficiency are lacking. • Future research directions for As-contaminated soil remediation are proposed. Arsenic (As) is a top human carcinogen widely distributed in the environment. As-contaminated soil exists worldwide and poses a threat on human health through water/food consumption, inhalation, or skin contact. More than 200 million people are exposed to excessive As concentration through direct or indirect exposure to contaminated soil. Therefore, affordable and efficient technologies that control risks caused by excess As in soil must be developed. The presently available methods can be classified as chemical, physical, and biological. Combined utilization of multiple technologies is also common to improve remediation efficiency. This review presents the research progress on different remediation technologies for As-contaminated soil. For chemical methods, common soil washing or immobilization agents were summarized. Physical technologies were mainly discussed from the field scale. Phytoextraction, the most widely used technology for As-contaminated soil in China, was the main focus for bioremediation. Method development for evaluating soil remediation efficiency was also summarized. Further research directions were proposed based on literature analysis.     

Rapid and long-effective removal of broad-spectrum pollutants from aqueous system by ZVI/oxidants

• The coupling of oxidants with ZVI overcome the impedance of ZVI passive layer. • ZVI/oxidants system achieved fast and long-effective removal of contaminants. • Multiple mechanisms are involved in contaminants removal by ZVI/oxidant system. • ZVI/Oxidants did not change the reducing property of ORP in the fixed-bed system. Zero-valent iron (ZVI) technology has recently gained significant interest in the efficient sequestration of a wide variety of contaminants. However, surface passivation of ZVI because of its intrinsic passive layer would lead to the inferior reactivity of ZVI and its lower efficacy in contaminant removal. Therefore, to activate the ZVI surface cheaply, continuously, and efficiently is an important challenge that ZVI technology must overcome before its wide-scale application. To date, several physical and chemical approaches have been extensively applied to increase the reactivity of the ZVI surface toward the elimination of broad-spectrum pollutants. Nevertheless, these techniques have several limitations such as low efficacy, narrow working pH, eco-toxicity, and high installation cost. The objective of this mini-review paper is to identify the critical role of oxygen in determining the reactivity of ZVI toward contaminant removal. Subsequently, the effect of three typical oxidants (H₂O₂, KMnO₄, and NaClO) on broad-spectrum contaminants removal by ZVI has been documented and discussed. The reaction mechanism and sequestration efficacies of the ZVI/oxidant system were evaluated and reviewed. The technical basis of the ZVI/oxidant approach is based on the half-reaction of the cathodic reduction of the oxidants. The oxidants commonly used in the water treatment industry, i.e., NaClO, O₃, and H₂O₂, can be served as an ideal coupling electron receptor. With the combination of these oxidants, the surface corrosion of ZVI can be continuously driven. The ZVI/oxidants technology has been compared with other conventional technologies and conclusions have been drawn.     

Sustainable wood-based nanotechnologies for photocatalytic degradation of organic contaminants in aquatic environment

•Wood and its reassemblies are ideal substrates to develop novel photocatalysts. •Synthetic methods and mechanisms of wood-derived photocatalysts are summarized. •Advances in wood-derived photocatalysts for organic pollutant removal are summed up. •Metal doping, morphology control and semiconductor coupling methods are highlighted. •Structure-activity relationship and catalytic mechanism of photocatalysts are given. Wood-based nanotechnologies have received much attention in the area of photocatalytic degradation of organic contaminants in aquatic environment in recent years, because of the high abundance and renewability of wood as well as the high reaction activity and unique structural features of these materials. Herein, we present a comprehensive review of the current research activities centering on the development of wood-based nanocatalysts for photodegradation of organic pollutants. This review begins with a brief introduction of the development of photocatalysts and hierarchical structure of wood. The review then focuses on strategies of designing novel photocatalysts based on wood or its recombinants (such as 1D fiber, 2D films and 3D porous gels) using advanced nanotechnology including sol-gel method, hydrothermal method, magnetron sputtering method, dipping method and so on. Next, we highlight typical approaches that improve the photocatalytic property, including metal element doping, morphology control and semiconductor coupling. Also, the structure-activity relationship of photocatalysts is emphasized. Finally, a brief summary and prospect of wood-derived photocatalysts is provided.     

Redox reactions of iron and manganese oxides in complex systems

• Mechanisms of redox reactions of Fe- and Mn-oxides were discussed. • Oxidative reactions of Mn- and Fe-oxides in complex systems were reviewed. • Reductive reaction of Fe(II)/iron oxides in complex systems was examined. • Future research on examining the redox reactivity in complex systems was suggested. Conspectus Redox reactions of Fe- and Mn-oxides play important roles in the fate and transformation of many contaminants in natural environments. Due to experimental and analytical challenges associated with complex environments, there has been a limited understanding of the reaction kinetics and mechanisms in actual environmental systems, and most of the studies so far have only focused on simple model systems. To bridge the gap between simple model systems and complex environmental systems, it is necessary to increase the complexity of model systems and examine both the involved interaction mechanisms and how the interactions affected contaminant transformation. In this Account, we primarily focused on (1) the oxidative reactivity of Mn- and Fe-oxides and (2) the reductive reactivity of Fe(II)/iron oxides in complex model systems toward contaminant degradation. The effects of common metal ions such as Mn²⁺ , Ca²⁺, Ni²⁺, Cr³⁺ and Cu²⁺, ligands such as small anionic ligands and natural organic matter (NOM), and second metal oxides such as Al, Si and Ti oxides on the redox reactivity of the systems are briefly summarized.     

Ceramic water filter for point-of-use water treatment in developing countries: Principles,challenges and opportunities

• CWF is a sustainable POU water treatment method for developing areas. • CWF manufacturing process is critical for its filtration performance. • Simultaneous increase of flow rate and pathogen removal is a challenge. • Control of pore size distribution holds promises to improve CWF efficiency. • Novel coatings of CWFs are a promising method to improve contaminant removal. Drinking water source contamination poses a great threat to human health in developing countries. Point-of-use (POU) water treatment techniques, which improve drinking water quality at the household level, offer an affordable and convenient way to obtain safe drinking water and thus can reduce the outbreaks of waterborne diseases. Ceramic water filters (CWFs), fabricated from locally sourced materials and manufactured by local labor, are one of the most socially acceptable POU water treatment technologies because of their effectiveness, low-cost and ease of use. This review concisely summarizes the critical factors that influence the performance of CWFs, including (1) CWF manufacturing process (raw material selection, firing process, silver impregnation), and (2) source water quality. Then, an in-depth discussion is presented with emphasis on key research efforts to address two major challenges of conventional CWFs, including (1) simultaneous increase of filter flow rate and bacterial removal efficiency, and (2) removal of various concerning pollutants, such as viruses and metal(loid)s. To promote the application of CWFs, future research directions can focus on: (1) investigation of pore size distribution and pore structure to achieve higher flow rates and effective pathogen removal by elucidating pathogen transport in porous ceramic and adjusting manufacture parameters; and (2) exploration of new surface modification approaches with enhanced interaction between a variety of contaminants and ceramic surfaces.     

Bioinspired cellulose-based membranes in oily wastewater treatment

• Cellulose-based membrane separates oily wastewater mimicking the living things. • The three central surface mechanisms were reviewed. • Preparation, performance, and mechanism are critically evaluated. • First review of wettability based cellulose membrane as major material. • The current and future importance of the research are discussed. It is challenging to purify oily wastewater, which affects water-energy-food production. One promising method is membrane-based separation. This paper reviews the current research trend of applying cellulose as a membrane material that mimics one of three typical biostructures: superhydrophobic, underwater superoleophobic, and Janus surfaces. Nature has provided efficient and effective structures through the evolutionary process. This has inspired many researchers to create technologies that mimic nature’s structures or the fabrication process. Lotus leaves, fish scales, and Namib beetles are three representative structures with distinct functional and surface properties: superhydrophobic, underwater superoleophobic, and Janus surfaces. The characteristics of these structures have been widely studied and applied to membrane materials to improve their performance. One attractive membrane material is cellulose, which has been studied from the perspective of its biodegradability and sustainability. In this review, the principles, mechanisms, fabrication processes, and membrane performances are summarized and compared. The theory of wettability is also described to build a comprehensive understanding of the concept. Finally, future outlook is discussed to challenge the gap between laboratory and industrial applications.     

Advances in airborne microorganisms detection using biosensors: A critical review

• Airborne microorganism detection methods are summarized. • Biosensors play an important role in detecting airborne microorganisms. • The principle of biosensor detection of airborne microorganisms is introduced. • The application and progress of biosensor in recent years is summarized. • The future perspectives of biosensor are identified. Humanity has been facing the threat of a variety of infectious diseases. Airborne microorganisms can cause airborne infectious diseases, which spread rapidly and extensively, causing huge losses to human society on a global scale. In recent years, the detection technology for airborne microorganisms has developed rapidly; it can be roughly divided into biochemical, immune, and molecular technologies. However, these technologies still have some shortcomings; they are time-consuming and have low sensitivity and poor stability. Most of them need to be used in the ideal environment of a laboratory, which limits their applications. A biosensor is a device that converts biological signals into detectable signals. As an interdisciplinary field, biosensors have successfully introduced a variety of technologies for bio-detection. Given their fast analysis speed, high sensitivity, good portability, strong specificity, and low cost, biosensors have been widely used in environmental monitoring, medical research, food and agricultural safety, military medicine and other fields. In recent years, the performance of biosensors has greatly improved, becoming a promising technology for airborne microorganism detection. This review introduces the detection principle of biosensors from the three aspects of component identification, energy conversion principle, and signal amplification. It also summarizes its research and application in airborne microorganism detection. The new progress and future development trend of the biosensor detection of airborne microorganisms are analyzed.     

Crosslinking acrylamide with EDTA-intercalated layered double hydroxide for enhanced recovery of Cr(VI) and Congo red: Adsorptive and mechanistic study

• Functional groups of AM and EDTA in composite increased removal of Cr(VI) and CR. • Removal process reached equilibrium within 30 min and was minimally affected by pH. • Elimination of Cr(VI) was promoted by coexisting CR. • Adsorption process of CR was less influenced by the presence of Cr(VI). • Mechanisms were electrostatic attraction, surface complexation and anion exchange. We prepared ethylenediaminetetraacetic acid (EDTA)-intercalated MgAl-layered double hydroxide (LDH-EDTA), then grafted acrylamide (AM) to the LDH-EDTA by a cross-linking method to yield a LDH-EDTA-AM composite; we then evaluated its adsorptive ability for Congo red (CR) and hexavalent chromium (Cr(VI)) in single and binary adsorption systems. The adsorption process on LDH-EDTA-AM for CR and Cr(VI) achieved equilibrium quickly, and the removal efficiencies were minimally affected by initial pH. The maximum uptake quantities of CR and Cr(VI) on LDH-EDTA-AM were 632.9 and 48.47 mg/g, respectively. In mixed systems, chromate removal was stimulated by the presence of CR, while the adsorption efficiency of CR was almost not influenced by coexisting Cr(VI). The mechanisms involved electrostatic attraction, surface complexation, and anion exchange for the adsorption of both hazardous pollutants. In the Cr(VI) adsorption process, reduction also took place. The removal efficiencies in real contaminated water were all higher than those in the laboratory solutions.     

In situ synthesis of FeS/Carbon fibers for the effective removal of Cr(VI) in aqueous solution

• FeS/carbon fibers were in situ synthesized with Fe-carrageenan hydrogel fiber. • The double helix structure of carrageenan is used to load and disperse Fe. • Pyrolyzing sulfate groups enriched carrageenan-Fe could easily generate FeS. • The adsorption mechanisms include reduction and complexation reaction. Iron sulfide (FeS) nanoparticles (termed FSNs) have attracted much attention for the removal of pollutants due to their high efficiency and low cost, and because they are environmentally friendly. However, issues of agglomeration, transformation, and the loss of active components limit their application. Therefore, this study investigates in situ synthesized FeS/carbon fibers with an Fe-carrageenan biomass as a precursor and nontoxic sulfur source to ascertain the removal efficiency of the fibers. The enrichment of sulfate groups as well as the double-helix structure in ι-carrageenan-Fe could effectively avoid the aggregation and loss of FSNs in practical applications. The obtained FeS/carbon fibers were used to control a Cr(VI) polluted solution, and exhibited a relatively high removal capacity (81.62 mg/g). The main mechanisms included the reduction of FeS, electrostatic adsorption of carbon fibers, and Cr(III)-Fe(III) complexation reaction. The pseudo-second-order kinetic model and Langmuir adsorption model both provided a good fit of the reaction process; hence, the removal process was mainly controlled by chemical adsorption, specifically monolayer adsorption on a uniform surface. Furthermore, co-existing anions, column, and regeneration experiments indicated that the FeS/carbon fibers are a promising remediation material for practical application.     

Composition,dispersion, and health risks of bioaerosols in wastewater treatment plants: A review

• Bioaerosols are produced in the process of wastewater biological treatment. • The concentration of bioaerosol indoor is higher than outdoor. • Bioaerosols contain large amounts of potentially pathogenic biomass and chemicals. • Inhalation is the main route of exposure of bioaerosol. • Both the workers and the surrounding residents will be affected by the bioaerosol. Bioaerosols are defined as airborne particles (0.05–100 mm in size) of biological origin. They are considered potentially harmful to human health as they can contain pathogens such as bacteria, fungi, and viruses. This review summarizes the most recent research on the health risks of bioaerosols emitted from wastewater treatment plants (WWTPs) in order to improve the control of such bioaerosols. The concentration and size distribution of WWTP bioaerosols; their major emission sources, composition, and health risks; and considerations for future research are discussed. The major themes and findings in the literature are as follows: the major emission sources of WWTP bioaerosols include screen rooms, sludge-dewatering rooms, and aeration tanks; the bioaerosol concentrations in screen and sludge-dewatering rooms are higher than those outdoors. WWTP bioaerosols contain a variety of potentially pathogenic bacteria, fungi, antibiotic resistance genes, viruses, endotoxins, and toxic metal(loid)s. These potentially pathogenic substances spread with the bioaerosols, thereby posing health risks to workers and residents in and around the WWTP. Inhalation has been identified as the main exposure route, and children are at a higher risk of this than adults. Future studies should identify emerging contaminants, establish health risk assessments, and develop prevention and control systems.     

Enhanced carbon tetrachloride degradation by hydroxylamine in ferrous ion activated calcium peroxide in the presence of formic acid

• Complete CT degradation was achieved by employing HA to CP/Fe(II)/FA process. • Quantitative detection of Fe(II) regeneration and HO• production was investigated. • Benzoic acid outcompeted FA for the reaction with HO•. • CO₂•⁻ was the dominant reductive radical for CT removal. • Effects of solution matrix on CT removal were conducted. Hydroxyl radicals (HO•) show low reactivity with perchlorinated hydrocarbons, such as carbon tetrachloride (CT), in conventional Fenton reactions, therefore, the generation of reductive radicals has attracted increasing attention. This study investigated the enhancement of CT degradation by the synergistic effects of hydroxylamine (HA) and formic acid (FA) (initial [CT] = 0.13 mmol/L) in a Fe(II) activated calcium peroxide (CP) Fenton process. CT degradation increased from 56.6% to 99.9% with the addition of 0.78 mmol/L HA to the CP/Fe(II)/FA/CT process in a molar ratio of 12/6/12/1. The results also showed that the presence of HA enhanced the regeneration of Fe(II) from Fe(III), and the production of HO• increased one-fold when employing benzoic acid as the HO• probe. Additionally, FA slightly improves the production of HO•. A study of the mechanism confirmed that the carbon dioxide radical (CO₂•⁻), a strong reductant generated by the reaction between FA and HO•, was the dominant radical responsible for CT degradation. Almost complete CT dechlorination was achieved in the process. The presence of humic acid and chloride ion slightly decreased CT removal, while high doses of bicarbonate and high pH inhibited CT degradation. This study helps us to better understand the synergistic roles of FA and HA for HO• and CO₂•⁻ generation and the removal of perchlorinated hydrocarbons in modified Fenton systems.     

A review of measurement methods for peracetic acid (PAA)

• Physical and chemical properties and application of peracetic acid solution. • Determination method of high concentration peracetic acid. • Determination method of residual peracetic acid (low concentration). Peroxyacetic acid has been widely used in food, medical, and synthetic chemical fields for the past several decades. Recently, peroxyacetic acid has gradually become an effective alternative disinfectant in wastewater disinfection and has strong redox capacity for removing micro-pollutants from drinking water. However, commercial peroxyacetic acid solutions are primarily multi-component mixtures of peroxyacetic acid, acetic acid, hydrogen peroxide, and water. During the process of water treatment, peroxyacetic acid and hydrogen peroxide (H₂O₂) often coexist, which limits further investigation on the properties of peroxyacetic acid. Therefore, analytical methods need to achieve a certain level of selectivity, particularly when peroxyacetic acid and hydrogen peroxide coexist. This review summarizes the measurement and detection methods of peroxyacetic acid, comparing the principle, adaptability, and relative merits of these methods.     

Membrane-based treatment of shale oil and gas wastewater: The current state of knowledge

• Shale oil and gas production generates wastewater with complex composition. • Membrane technologies emerged for the treatment of shale oil and gas wastewater. • Membrane technologies should tolerate high TDS and consume low primary energy. • Pretreatment is a key component of integrated wastewater treatment systems. • Full-scale implementation of membrane technologies is highly desirable. Shale oil and gas exploitation not only consumes substantial amounts of freshwater but also generates large quantities of hazardous wastewater. Tremendous research efforts have been invested in developing membrane-based technologies for the treatment of shale oil and gas wastewater. Despite their success at the laboratory scale, membrane processes have not been implemented at full scale in the oil and gas fields. In this article, we analyze the growing demands of wastewater treatment in shale oil and gas production, and then critically review the current stage of membrane technologies applied to the treatment of shale oil and gas wastewater. We focus on the unique niche of those technologies due to their advantages and limitations, and use mechanical vapor compression as the benchmark for comparison. We also highlight the importance of pretreatment as a key component of integrated treatment trains, in order to improve the performance of downstream membrane processes and water product quality. We emphasize the lack of sufficient efforts to scale up existing membrane technologies, and suggest that a stronger collaboration between academia and industry is of paramount importance to translate membrane technologies developed in the laboratory to the practical applications by the shale oil and gas industry.     

Dual-functional sites for synergistic adsorption of Cr(VI) and Sb(V) by polyaniline-TiO2 hydrate: Adsorption behaviors,sites and mechanisms

• PANI/Ti(OH)_n^(4–n)+ exhibited excellent adsorption capacity and reusability. • Adsorption sites of Cr(VI) were hydroxyl, amino/imino group and benzene rings. • Sb(V) was adsorbed mainly through hydrogen bonds and Ti-O-Sb. • The formation of Cr-O-Sb in dual system demonstrated the synergistic adsorption. • PANI/TiO₂ was a potential widely-applied adsorbent and worth further exploring. Removal of chromium (Cr) and antimony (Sb) from aquatic environments is crucial due to their bioaccumulation, high mobility and strong toxicity. In this work, a composite adsorbent consisting of Ti(OH)_n^(4–n)+ and polyaniline (PANI) was designed and successfully synthesized by a simple and eco-friendly method for the uptake of Cr(VI) and Sb(V). The synthetic PANI/TiO₂ composites exhibited excellent adsorption capacities for Cr(VI) and Sb(V) (394.43 mg/g for Cr(VI) and 48.54 mg/g for Sb(V)), wide pH applicability and remarkable reusability. The adsorption of Cr(VI) oxyanions mainly involved electrostatic attraction, hydrogen bonding and anion-π interactions. Based on X-ray photoelectron spectroscopy and FT-IR analysis, the adsorption sites were shown to be hydroxyl groups, amino/imino groups and benzene rings. Sb(V) was adsorbed mainly through hydrogen bonds and surface complexation to form Ti-O-Sb complexes. The formation of Cr-O-Sb in the dual system demonstrated the synergistic adsorption of Cr(VI) and Sb(V). More importantly, because of the different adsorption sites, the adsorption of Cr(VI) and Sb(V) occurred independently and was enhanced to some extent in the dual system. The results suggested that PANI/TiO₂ is a promising prospect for practical wastewater treatment in the removal of Cr(VI) and Sb(V) from wastewater owing to its availability, wide applicability and great reusability.     

Sorption mechanisms of diphenylarsinic acid on natural magnetite and siderite: Evidence from sorption kinetics,sequential extraction and extended X-ray absorption fine-structure spectroscopy analysis

• DPAA sorption followed pseudo-secondary and intra-particle diffusion models. • Chemical bonding and intra-particle diffusion were dominant rate-limiting steps. • DPAA simultaneously formed inner- and outer-sphere complexes on siderite. • DPAA predominantly formed occluded inner-sphere complexes on magnetite. • Bidentate binuclear bond was identified for DPAA on siderite and magnetite. Diphenylarsinic acid (DPAA) is both the prime starting material and major metabolite of chemical weapons (CWs). Because of its toxicity and the widespread distribution of abandoned CWs in burial site, DPAA sorption by natural Fe minerals is of considerable interest. Here we report the first study on DPAA sorption by natural magnetite and siderite using macroscopic sorption kinetics, sequential extraction procedure (SEP) and microscopic extended X-ray absorption fine-structure spectroscopy (EXAFS). Our results show that the sorption pseudo-equilibrated in 60 minutes and that close to 50% and 20%–30% removal can be achieved for magnetite and siderite, respectively, at the initial DPAA concentrations of 4–100 mg/L. DPAA sorption followed pseudo-secondary and intra-particle diffusion kinetics models, and the whole process was mainly governed by intra-particle diffusion and chemical bonding. SEP and EXAFS results revealed that DPAA mainly formed inner-sphere complexes on magnetite (>80%), while on siderite it simultaneously resulted in outer-sphere and inner-sphere complexes. EXAFS analysis further confirmed the formation of inner-sphere bidentate binuclear corner-sharing complexes (²C) for DPAA. Comparison of these results with previous studies suggests that phenyl groups are likely to impact the sorption capacity and structure of DPAA by increasing steric hindrance or affecting the way the central arsenic (As) atom maintains charge balance. These results improve our knowledge of DPAA interactions with Fe minerals, which will help to develop remediation technology and predict the fate of DPAA in soil-water environments.     

Fate and risk assessment of emerging contaminants in reclaimed water production processes

• PPCPs had the highest removal efficiency in A²O combined with MBR process (86.8%). • ARGs and OPFRs were challenging to remove (6.50% and 31.0%, respectively). • Octocrylene and tris(2-ethylhexyl) phosphate posed high risks to aquatic organisms. • Meta-analysis was used to compare the ECs removal in wastewater treatment. • Membrane treatment technology is the most promising treatment for ECs removal. Reclaimed water has been widely applied in irrigation and industrial production. Revealing the behavior of emerging contaminants in the production process of reclaimed water is the first prerequisite for developing relevant water quality standards. This study investigated 43 emerging contaminants, including 22 pharmaceuticals and personal care products (PPCPs), 11 organophosphorus flame retardants (OPFRs), and 10 antibiotic resistance genes (ARGs) in 3 reclaimed wastewater treatment plants (RWTPs) in Beijing. The composition profiles and removal efficiencies of these contaminants in RWTPs were determined. The results indicated that the distribution characteristics of the different types of contaminants in the three RWTPs were similar. Caffeine, sul2 and tris(1-chloro-2-propyl) phosphate were the dominant substances in the wastewater, and their highest concentrations were 27104 ng/L, 1.4 × 10⁷ copies/mL and 262 ng/L, respectively. Ofloxacin and sul2 were observed to be the dominant substances in the sludge, and their highest concentrations were 5419 ng/g and 3.7 × 10⁸ copies/g, respectively. Anaerobic/anoxic/oxic system combined with the membrane bioreactor process achieved a relatively high aqueous removal of PPCPs (87%). ARGs and OPFRs were challenging to remove, with average removal rates of 6.5% and 31%, respectively. Quantitative meta-analysis indicated that tertiary treatment processes performed better in emerging contaminant removal than secondary processes. Diethyltoluamide exhibited the highest mass load discharge, with 33.5 mg/d per 1000 inhabitants. Octocrylene and tris(2-ethylhexyl) phosphate posed high risks (risk quotient>1.0) to aquatic organisms. This study provides essential evidence to screen high priority pollutants and develop corresponding standard in RWTPs.     

Bioinspired and biomimetic membranes for water purification and chemical separation: A review

•The history of biological and artificial water channels is reviewed. •A comprehensive channel characterization platform is introduced. •Rationale designs and fabrications of biomimetic membranes are summarized. •The advantages, limitations, and challenges of biomimetic membranes are discussed. •The prospect and scalable solutions of biomimetic membranes are discussed. Bioinspired and biomimetic membranes that contain biological transport channels or attain their structural designs from biological systems have been through a remarkable development over the last two decades. They take advantage of the exceptional transport properties of those channels, thus possess both high permeability and selectivity, and have emerged as a promising solution to existing membranes. Since the discovery of biological water channel proteins aquaporins (AQPs), extensive efforts have been made to utilize them to make separation membranes–AQP-based membranes, which have been commercialized. The exploration of AQPs’ unique structures and transport properties has resulted in the evolution of biomimetic separation materials from protein-based to artificial channel-based membranes. However, large-scale, defect-free biomimetic membranes are not available yet. This paper reviews the state-of-the-art biomimetic membranes and summarizes the latest research progress, platform, and methodology. Then it critically discusses the potential routes of this emerging area toward scalable applications. We conclude that an appropriate combination of bioinspired concepts and molecular engineering with mature polymer industry may lead to scalable polymeric membranes with intrinsic selective channels, which will gain the merit of both desired selectivity and scalability.     

Biogenic palladium prepared by activated sludge microbes for the hexavalent chromium catalytic reduction: Impact of relative biomass

• Pd nanoparticles could be reduced and supported by activated sludge microbes. • The effect of biomass on Pd adsorption by microbes is greater than Pd reduction. • More biomass reduces Pd particle size, which is more dispersed on the cell surface. • When the biomass/Pd add to 6, the catalytic reduction rate of Cr(VI) reaches stable. Palladium, a kind of platinum group metal, owns catalytic capacity for a variety of hydrogenations. In this study, Pd nanoparticles (PdNPs) were generated through enzymatic recovery by microbes of activated sludge at various biomass/Pd, and further used for the Cr(VI) reduction. The results show that biomass had a strong adsorption capacity for Pd(II), which was 17.25 mg Pd/g sludge. The XRD and TEM-EDX results confirmed the existence of PdNPs associated with microbes (bio-Pd). The increase of biomass had little effect on the reduction rate of Pd(II), but it could cause decreasing particle size and shifting location of Pd(0) with the better dispersion degree on the cell surface. In the Cr(VI) reduction experiments, Cr(VI) was first adsorbed on bio-Pd with hydrogen and then reduced using active hydrogen as electron donor. Biomass improved the catalytic activity of PdNPs. When the biomass/Pd (w/w) ratio increased to six or higher, Cr(VI) reduction achieved maximum rate that 50 mg/L of Cr(VI) could be rapidly reduced in one minute.