Effectiveness of emission control technologies for auxiliary engines on ocean-going vessels

Large auxiliary engines operated on ocean-going vessels in transit and at berth impact the air quality of populated areas near ports. This paper presents new information on the comparison of emission ranges from three similar engines and the effectiveness of three control technologies: switching to cleaner burning fuels, operating in the low oxides of nitrogen (NOx) mode, and selective catalytic reduction (SCR). In-use measurements of gaseous (NOx, carbon monoxide [CO], carbon dioxide [CO2]) and fine particulate matter (PM2.5; total and speciated) emissions were made on three auxiliary engines on post-PanaMax class container vessels following the International Organization for Standardization-8178-1 protocol. The in-use NOx emissions for the MAN B&W 7L32/40 engine family vary from 15 to 21.1 g/kW-hr for heavy fuel oil and 8.9 to 19.6 g/kW-hr for marine distillate oil. Use of cleaner burning fuels resulted in NOx reductions ranging from 7 to 41% across different engines and a PM2.5 reduction of up to 83%. The NOx reductions are a consequence of fuel nitrogen content and engine operation; the PM2.5 reduction is attributed to the large reductions in the hydrated sulfate and organic carbon (OC) fractions. As expected, operating in the low-NOx mode reduced NOx emissions by approximately 32% and nearly doubled elemental carbon (EC) emissions. However, PM2.5 emission factors were nearly unchanged because the EC emission factor is only approximately 5% of the total PM2.5 mass. SCR reduced the NOx emission factor to less than 2.4 g/kW-hr, but it increased the PM2.5 emissions by a factor of 1.5-3.8. This increase was a direct consequence of the conversion of sulfur dioxide to sulfate emissions on the SCR catalyst. The EC and OC fractions of PM2.5 reduced across the SCR unit.     

Determination of the emissions from an aircraft auxiliary power unit (APU) during the Alternative Aviation Fuel Experiment (AAFEX)

The emissions from a Garrett-AiResearch (now Honeywell) Model GTCP85-98CK auxiliary power unit (APU) were determined as part of the National Aeronautics and Space Administration's (NASA's) Alternative Aviation Fuel Experiment (AAFEX) using both JP-8 and a coal-derived Fischer Tropsch fuel (FT-2). Measurements were conducted by multiple research organizations for sulfur dioxide (SO2, total hydrocarbons (THC), carbon monoxide (CO), carbon dioxide (CO2), nitrogen oxides (NOx), speciated gas-phase emissions, particulate matter (PM) mass and number, black carbon, and speciated PM. In addition, particle size distribution (PSD), number-based geometric mean particle diameter (GMD), and smoke number were also determined from the data collected. The results of the research showed PM mass emission indices (EIs) in the range of 20 to 700 mg/kg fuel and PM number EIs ranging from 0.5 x 10(15) to 5 x 10(15) particles/kg fuel depending on engine load and fuel type. In addition, significant reductions in both the SO2 and PM EIs were observed for the use of the FT fuel. These reductions were on the order of approximately 90% for SO2 and particle mass EIs and approximately 60% for the particle number EI, with similar decreases observed for black carbon. Also, the size of the particles generated by JP-8 combustion are noticeably larger than those emitted by the APU burning the FT fuel with the geometric mean diameters ranging from 20 to 50 nm depending on engine load and fuel type. Finally, both particle-bound sulfate and organics were reduced during FT-2 combustion. The PM sulfate was reduced by nearly 100% due to lack of sulfur in the fuel, with the PM organics reduced by a factor of approximately 5 as compared with JP-8.     

Idle emissions from heavy-duty diesel vehicles: review and recent data

Heavy-duty diesel vehicle idling consumes fuel and reduces atmospheric quality, but its restriction cannot simply be proscribed, because cab heat or air-conditioning provides essential driver comfort. A comprehensive tailpipe emissions database to describe idling impacts is not yet available. This paper presents a substantial data set that incorporates results from the West Virginia University transient engine test cell, the E-55/59 Study and the Gasoline/Diesel PM Split Study. It covered 75 heavy-duty diesel engines and trucks, which were divided into two groups: vehicles with mechanical fuel injection (MFI) and vehicles with electronic fuel injection (EFI). Idle emissions of CO, hydrocarbon (HC), oxides of nitrogen (NOx), particulate matter (PM), and carbon dioxide (CO2) have been reported. Idle CO2 emissions allowed the projection of fuel consumption during idling. Test-to-test variations were observed for repeat idle tests on the same vehicle because of measurement variation, accessory loads, and ambient conditions. Vehicles fitted with EFI, on average, emitted approximately 20 g/hr of CO, 6 g/hr of HC, 86 g/hr of NOx, 1 g/hr of PM, and 4636 g/hr of CO2 during idle. MFI equipped vehicles emitted approximately 35 g/hr of CO, 23 g/hr of HC, 48 g/hr of NOx, 4 g/hr of PM, and 4484 g/hr of CO2, on average, during idle. Vehicles with EFI emitted less idle CO, HC, and PM, which could be attributed to the efficient combustion and superior fuel atomization in EFI systems. Idle NOx, however, increased with EFI, which corresponds with the advancing of timing to improve idle combustion. Fuel injection management did not have any effect on CO2 and, hence, fuel consumption. Use of air conditioning without increasing engine speed increased idle CO2, NOx, PM, HC, and fuel consumption by 25% on average. When the engine speed was elevated from 600 to 1100 revolutions per minute, CO2 and NOx emissions and fuel consumption increased by >150%, whereas PM and HC emissions increased by approximately 100% and 70%, respectively. Six Detroit Diesel Corp. (DDC) Series 60 engines in engine test cell were found to emit less CO, NOx, and PM emissions and consumed fuel at only 75% of the level found in the chassis dynamometer data. This is because fan and compressor loads were absent in the engine test cell.     

Open burning of household waste: Effect of experimental condition on combustion quality and emission of PCDD, PCDF and PCB

Open burning for waste disposal is, in many countries, the dominant source of polychlorinated dibenzodioxins, dibenzofurans and biphenyls (PCDD/PCDF/PCB) release to the environment. To generate emission factors for open burning, experimental pile burns of about 100 kg of household waste were conducted with emissions sampling. From these experiments and others conducted by the same authors it is found that less compaction of waste or active mixing during the fire - “stirring” - promotes better combustion (as evidenced by lower CO/CO₂ ratio) and reduces emissions of PCDD/PCDF/PCB; an intuitive but previously undemonstrated result. These experiments also support previous results suggesting PCDD/PCDF/PCB generation in open burning - while still highly variable - tends to be greater in the later (smoldering) phases of burning when the CO/CO₂ ratio increases.     

Remote sensing-based estimates of annual and seasonal emissions from crop residue burning in the contiguous United States

Crop residue burning is an extensive agricultural practice in the contiguous United States (CONUS). This analysis presents the results of a remote sensing-based study of crop residue burning emissions in the CONUS for the time period 2003-2007 for the atmospheric species of carbon dioxide (CO2), methane (CH4), carbon monoxide (CO), nitrogen dioxide (NO2, sulfur dioxide (SO2), PM2.5 (particulate matter [PM] < or = 2.5 microm in aerodynamic diameter), and PM10 (PM < or = 10 microm in aerodynamic diameter). Cropland burned area and associated crop types were derived from Moderate Resolution Imaging Spectroradiometer (MODIS) products. Emission factors, fuel load, and combustion completeness estimates were derived from the scientific literature, governmental reports, and expert knowledge. Emissions were calculated using the bottom-up approach in which emissions are the product of burned area, fuel load, and combustion completeness for each specific crop type. On average, annual crop residue burning in the CONUS emitted 6.1 Tg of CO2, 8.9 Gg of CH4, 232.4 Gg of CO, 10.6 Gg of NO2, 4.4 Gg of SO2, 20.9 Gg of PM2.5, and 28.5 Gg of PM10. These emissions remained fairly consistent, with an average interannual variability of crop residue burning emissions of +/- 10%. The states with the highest emissions were Arkansas, California, Florida, Idaho, Texas, and Washington. Most emissions were clustered in the southeastern United States, the Great Plains, and the Pacific Northwest. Air quality and carbon emissions were concentrated in the spring, summer, and fall, with an exception because of winter harvesting of sugarcane in Florida, Louisiana, and Texas. Sugarcane, wheat, and rice residues accounted for approximately 70% of all crop residue burning and associated emissions. Estimates of CO and CH4 from agricultural waste burning by the U.S. Environmental Protection Agency were 73 and 78% higher than the CO and CH4 emission estimates from this analysis, respectively. This analysis also showed that crop residue burning emissions are a minor source of CH4 emissions (< 1%) compared with the CH4 emissions from other agricultural sources, specifically enteric fermentation, manure management, and rice cultivation.     

An assessment of air emissions from liquefied natural gas ships using different power systems and different fuels

The shipping industry has been an unrecognized source of criteria pollutants: nitrogen oxides (NOx), volatile organic compounds, coarse particulate matter (PM10), fine particulate matter (PM2.5), sulfur dioxide (SO2), and carbon monoxide (CO). Liquefied natural gas (LNG) has traditionally been transported via steam turbine (ST) ships. Recently, LNG shippers have begun using dual-fuel diesel engines (DFDEs) to propel and offload their cargoes. Both the conventional ST boilers and DFDE are capable of burning a range of fuels, from heavy fuel oil to boil-off-gas (BOG) from the LNG load. In this paper a method for estimating the emissions from ST boilers and DFDEs during LNG offloading operations at berth is presented, along with typical emissions from LNG ships during offloading operations under different scenarios ranging from worst-case fuel oil combustion to the use of shore power. The impact on air quality in nonattainment areas where LNG ships call is discussed. Current and future air pollution control regulations for ocean-going vessels (OGVs) such as LNG ships are also discussed. The objective of this study was to estimate and compare emissions of criteria pollutants from conventional ST and DFDE ships using different fuels. The results of this study suggest that newer DFDE ships have lower SO2 and PM2.5/PM10 emissions, conventional ST ships have lower NOx, volatile organic compound, and CO emissions; and DFDE ships utilizing shore power at berth produce no localized emissions because they draw their required power from the local electric grid.     

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.     

Determination of the emissions from an aircraft auxiliary power unit (APU) during the Alternative Aviation Fuel Experiment (AAFEX)

The emissions from a Garrett-AiResearch (now Honeywell) Model GTCP85–98CK auxiliary power unit (APU) were determined as part of the National Aeronautics and Space Administration's (NASA's) Alternative Aviation Fuel Experiment (AAFEX) using both JP-8 and a coal-derived Fischer Tropsch fuel (FT-2). Measurements were conducted by multiple research organizations for sulfur dioxide (SO₂), total hydrocarbons (THC), carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x), speciated gas-phase emissions, particulate matter (PM) mass and number, black carbon, and speciated PM. In addition, particle size distribution (PSD), number-based geometric mean particle diameter (GMD), and smoke number were also determined from the data collected. The results of the research showed PM mass emission indices (EIs) in the range of 20 to 700 mg/kg fuel and PM number EIs ranging from 0.5?×?10¹⁵ to 5?×?10¹⁵ particles/kg fuel depending on engine load and fuel type. In addition, significant reductions in both the SO₂ and PM EIs were observed for the use of the FT fuel. These reductions were on the order of ～90% for SO₂ and particle mass EIs and ～60% for the particle number EI, with similar decreases observed for black carbon. Also, the size of the particles generated by JP-8 combustion are noticeably larger than those emitted by the APU burning the FT fuel with the geometric mean diameters ranging from 20 to 50 nm depending on engine load and fuel type. Finally, both particle-bound sulfate and organics were reduced during FT-2 combustion. The PM sulfate was reduced by nearly 100% due to lack of sulfur in the fuel, with the PM organics reduced by a factor of ～5 as compared with JP-8.

Implications: The results of this research show that APUs can be, depending on the level of fuel usage, an important source of air pollutant emissions at major airports in urban areas. Substantial decreases in emissions can also be achieved through the use of Fischer Tropsch (FT) fuel. Based on these results, the use of FT fuel could be a viable future control strategy for both gas- and particle-phase air pollutants.     

A life-cycle inventory model of municipal solid waste combustion

Evaluation of alternate strategies for municipal solid waste (MSW) management requires models to calculate environmental emissions as a function of both waste quantity and composition. A methodology to calculate waste component-specific emissions associated with MSW combustion is presented here. The methodology considers emissions at a combustion facility as well as those avoided at an electrical energy facility because of energy recovered from waste combustion. Emission factors, in units of kg pollutant per metric ton MSW entering the combustion facility, are calculated for CO2-biomass, CO2-fossil, SOx, HCl, NOx, dioxins/furans, PM, CO, and 11 metals. Water emissions associated with electrical energy offsets are also considered. Reductions in environmental emissions for a 500-metric-ton-per-day combustion facility that recovers energy are calculated.     

Emissions from Slash Burning and the Influence of Flame Retardant Chemicals

Pollutants sampled during the burning of 30 lb ponderosa pine fuel beds yielded emission factors for CO, hydrocarbon gases, and par-ticulate matter of 146, 8.4, and 9.1 lb/ton of fuel, respectively. When similar beds were treated with diammonium phosphate flame retardant, these factors increased to 166, 11.7, and 19.3 lb/ton of fuel, respectively.

Gas chromatographic analysis of hydrocarbon gases showed that 15-40% of this material was composed of methane and eth-ylene. Ethane and acetylene were the next most abundant materials, with photochemically important materials constituting minor portions of this gaseous component. Fuel beds treated with flame retardant produced more oiefins, and this production lasted throughout the smoldering phase of burning.

These tests showed that the smoldering phase of combustion is of major importance to air pollutant production during slash burning. The initial 80% of the fuel burned accounted for only 20-30% of HC and CO emissions. This suggests that a rapid mop-up of slash burns could substantially reduce air pollutant production.     

Emissions and demonstration of an emission control technology for small two-stroke utility engines

Small utility engines represent an important contribution to the emissions inventory and have been subjected to increasingly stringent regulations in recent years. For this project, a Tanaka two-stroke engine was tested in its original condition and with a modified fuel/oil injection system. The modified fuel/oil injection system applied to the Tanaka two-stroke engine resulted in significant emissions reductions of approximately 52% for carbon monoxide (CO), 70% for total hydrocarbons (THC), 70% for particulate matter (PM), and 67% for the regulated THC + nitrogen oxides metric. This technology met the California Air Resources Board's 2000 model-year regulations for all pollutants, with the exception of slightly higher PM emissions. Two additional two-stroke engines were tested under a new condition and after at least 100 hr of use to examine the effects of deterioration on in-use, two-stroke engines. For one engine, CO and PM emissions more than tripled after 162 hr of operation in the field, with smaller increases also observed for THC (20%). For the second engine, significant repairs were required throughout the 100 operating hours, which counteracted the effects of the emissions deterioration and resulted in lower CO and THC emissions.     

2010—2019年成都市机动车排污特征分析及防控措施减排效果评估

为评估2010—2019年成都市机动车防控措施的减排效果,以2010年为基准年,采用排放清单法计算了各减排措施下2019年的减排量,对比分析了4种控制措施的减排效益。结果表明：成都市机动车排污总量逐年下降,2019年PM_2.5、NO_x、VOCs、CO、SO₂和NH₃的排放量分别为0.27×10⁴、4.63×10⁴、1.70×10⁴、28.99×10⁴、0.21×10⁴和0.45×10⁴ t,主要分布在中心城区,其中重型货车对PM_2.5和NO_x贡献最大,小型客车对VOCs、CO、SO₂和NH₃贡献最大;措施中加严标准的综合减排量最大,重点减排车型为小型客车、轻型货车、公交车等,2019年6种污染物减排量分别为0.14×10⁴、2.27×10⁴、1.29×10⁴、6.77×10⁴、0.07×10⁴和0.38×10⁴ t;优化城市交通管理对小型客车和摩托车的减排效果显著,2019年6种污染物减排量分别为0.04×10⁴、0.81×10⁴、0.38×10⁴、2.55×10⁴、0.05×10⁴和0.04×10⁴ t;淘汰高排放车辆对小型客车、轻型货车等的减排较明显,2019年6种污染物减排放量分别为0.13×10⁴、0.98×10⁴、0.34×10⁴、2.62×10⁴、0.01×10⁴和0.007×10⁴ t;推广清洁能源汽车的重点减排车型为出租车和公交车,虽然可有效减少PM_2.5、NO_x的排放,但VOCs却有小幅增加,2019年6种污染物减排放量分别为0.12×10⁴、0.62×10⁴、−0.13×10⁴、0.30×10⁴、0.004×10⁴和0.000 5×10⁴ t。     

A fuel-based assessment of off-road diesel engine emissions

The use of diesel engines in off-road applications is a significant source of nitrogen oxides (NOx) and particulate matter (PM10). Such off-road applications include railroad locomotives, marine vessels, and equipment used for agriculture, construction, logging, and mining. Emissions from these sources are only beginning to be controlled. Due to the large number of these engines and their wide range of applications, total activity and emissions from these sources are uncertain. A method for estimating the emissions from off-road diesel engines based on the quantity of diesel fuel consumed is presented. Emission factors are normalized by fuel consumption, and total activity is estimated by the total fuel consumed. Total exhaust emissions from off-road diesel equipment (excluding locomotives and marine vessels) in the United States during 1996 have been estimated to be 1.2 x 10(9) kg NOx and 1.2 x 10(8) kg PM10. Emissions estimates published by the U.S. Environmental Protection Agency are 2.3 times higher for both NOx and exhaust PM10 emissions than estimates based directly on fuel consumption. These emissions estimates disagree mainly due to differences in activity estimates, rather than to differences in the emission factors. All current emission inventories for off-road engines are uncertain because of the limited in-use emissions testing that has been performed on these engines. Regional- and state-level breakdowns in diesel fuel consumption by off-road mobile sources are also presented. Taken together with on-road measurements of diesel engine emissions, results of this study suggest that in 1996, off-road diesel equipment (including agriculture, construction, logging, and mining equipment, but not locomotives or marine vessels) was responsible for 10% of mobile source NOx emissions nationally, whereas on-road diesel vehicles contributed 33%.     

Inventory of aerosol and sulphur dioxide emissions from India. Part II—biomass combustion

A spatially resolved biomass burning data set, and related emissions of sulphur dioxide and aerosol chemical constituents was constructed for India, for 1996–1997 and extrapolated to the INDOEX period (1998–1999). Sources include biofuels (wood, crop waste and dung-cake) and forest fires (accidental, shifting cultivation and controlled burning). Particulate matter (PM) emission factors were compiled from studies of Indian cooking stoves and from literature for open burning. Black carbon (BC) and organic matter (OM) emissions were estimated from these, accounting for combustion temperatures in cooking stoves. Sulphur dioxide emission factors were based on fuel sulphur content and reported literature measurements. Biofuels accounted 93% of total biomass consumption (577 MT yr⁻¹), with forest fires contributing only 7%. The national average biofuel mix was 56 : 21 : 23% of fuelwood, crop waste and dung-cake, respectively. Compared to fossil fuels, biomass combustion was a minor source of SO₂ (7% of total), with higher emissions from dung-cake because of its higher sulphur content. PM_2.5 emissions of 2.04 Tg yr⁻¹ with an “inorganic fraction” of 0.86 Tg yr⁻¹ were estimated. Biomass combustion was the major source of carbonaceous aerosols, accounting 0.25 Tg yr⁻¹ of BC (72% of total) and 0.94 Tg yr⁻¹ of OM (76% of total). Among biomass, fuelwood and crop waste were primary contributors to BC emissions, while dung-cake and forest fires were primary contributors to OM emissions. Northern and the east-coast India had high densities of biomass consumption and related emissions. Measurements of emission factors of SO₂, size resolved aerosols and their chemical constituents for Indian cooking stoves are needed to refine the present estimates.     

A study on emission performance of a diesel engine fueled with five typical methyl ester biodiesels

As an alternative and renewable fuel, biodiesel can effectively reduce diesel engine emissions, especially particulate matter and dry soot. However, the biodiesel effects on emissions may vary as the source fuel changes. In this paper, the performance of five methyl esters with different sources was studied: cottonseed methyl ester (CME), soybean methyl ester (SME), rapeseed methyl ester (RME), palm oil methyl ester (PME) and waste cooking oil methyl ester (WME). Total particulate matter (PM), dry soot (DS), non-soot fraction (NSF), nitrogen oxide (NO_x), unburned hydrocarbon (HC), and carbon monoxide (CO) were investigated on a Cummins ISBe6 Euro III diesel engine and compared with a baseline diesel fuel. Results show that using different methyl esters results in large PM reductions ranging from 53% to 69%, which include the DS reduction ranging from 79% to 83%. Both oxygen content and viscosity could influence the DS emission. Higher oxygen content leads to less DS at high load while lower viscosity results in less DS at low load. NSF decreases consistently as cetane number increases except for PME. The cetane number could be responsible for the large NSF difference between different methyl esters.     

Effects of low concentration biodiesel blend application on modern passenger cars. Part 1: Feedstock impact on regulated pollutants, fuel consumption and particle emissions

Five biodiesels from different feedstocks (rapeseed, soy, sunflower, palm, and used fried oils) blended with diesel at 10% vol. ratio (B10), were tested on a Euro 3 common-rail passenger car. Limited effects (−2% to +4%) were observed on CO₂ emissions. CO and HC emissions increased between 10% and 25% on average, except at high speed - high power where emissions were too low to draw conclusions. NOx emissions increased by up to 20% for two out of the five blends, decreased by up to 15% for two other blends, and remained unchanged for one blend. Particulate matter (PM) was reduced for all blends by up to 25% and the reductions were positively correlated with the extent of biodiesel saturation. PM reductions are associated with consistent reductions in non-volatile particle number. A variable behaviour in particle number is observed when volatile particles are also accounted.     

基于EGR的乙醇-生物柴油-柴油发动机排放性能

在单缸风冷四冲程直喷柴油发电机上,燃用柴油、生物柴油、10%乙醇-45%生物柴油-45%柴油（E10B45D45）和20%乙醇-40%生物柴油-40%柴油（E20B40D40）,采用16%、28% EGR率,测试并分析了经济性,NOx、HC和CO的排放性能和烟气的光吸收系数。研究表明：柴油的油耗最低,生物柴油次之,随着乙醇含量的增加,混合燃料的油耗增加;随着乙醇含量的增多,NOx排放量降低,与燃用柴油相比,E10B45D45和E20B40D40平均可降低约16.1%和30.2%;采用EGR可有效降低NOx排放,对应16%、28% EGR率,E10B45D45的NOx排放可平均降低19.3%和39.5%,E20B40D40平均降低10.7%和43.5%;随着乙醇含量的增多,HC排放量显著升高,对比于柴油,E10B45D45和E20B40D40分别升高了59.8%和172.1%;采用EGR后,HC排放增加;随乙醇含量的增加,CO排放也明显增大,对比于柴油,E10B45D45和E20B40D40分别升高了58.6%和131.1%;采用EGR后CO排放增加;各燃料中,柴油在小、中负荷烟气的光吸收系数最低,大负荷时却最高;不宜在小负荷时采用较高的乙醇掺混比和较大的EGR率。     

轻型车燃用费托柴油的实际道路排放特征

利用便携式车载排放测试系统,对某款采用增压中冷和高压共轨技术的国Ⅳ轻型柴油车进行实际道路排放测试,研究其分别燃用石油基柴油、费托柴油和混合柴油（费托柴油与石油基柴油按一定比例混合而成）时,不同车速下的CO、THC、NOx和CO2排放特征和油耗变化情况。实验结果表明：对于3种柴油,所测4种气态物的排放均随着车速的增加而降低,当速度达到一定程度后趋于稳定;与石油基柴油相比,费托柴油和混合柴油的CO、NOx和CO2排放分别降低23%和5%,30%和24%,20%和20%,但THC排放均略有增加;通过碳平衡计算,费托柴油和混合柴油的体积油耗相对石油基柴油分别降低12%和17%。总的来说,燃用费托柴油和混合柴油时的气态污染物排放与石油基柴油具有相似的速度变化趋势,但费托柴油和混合柴油的整体尾气排放和油耗要低于石油基柴油。使用费托柴油或混合柴油是降低轻型柴油车实际道路排放的一个有效途径。     

Combustion aerosols: factors governing their size and composition and implications to human health

Particulate matter (PM) emissions from stationary combustion sources burning coal, fuel oil, biomass, and waste, and PM from internal combustion (IC) engines burning gasoline and diesel, are a significant source of primary particles smaller than 2.5 microns (PM2.5) in urban areas. Combustion-generated particles are generally smaller than geologically produced dust and have unique chemical composition and morphology. The fundamental processes affecting formation of combustion PM and the emission characteristics of important applications are reviewed. Particles containing transition metals, ultrafine particles, and soot are emphasized because these types of particles have been studied extensively, and their emissions are controlled by the fuel composition and the oxidant-temperature-mixing history from the flame to the stack. There is a need for better integration of the combustion, air pollution control, atmospheric chemistry, and inhalation health research communities. Epidemiology has demonstrated that susceptible individuals are being harmed by ambient PM. Particle surface area, number of ultrafine particles, bioavailable transition metals, polycyclic aromatic hydrocarbons (PAH), and other particle-bound organic compounds are suspected to be more important than particle mass in determining the effects of air pollution. Time- and size-resolved PM measurements are needed for testing mechanistic toxicological hypotheses, for characterizing the relationship between combustion operating conditions and transient emissions, and for source apportionment studies to develop air quality plans. Citations are provided to more specialized reviews, and the concluding comments make suggestions for further research.     

Combustion Aerosols: Factors Governing Their Size and Composition and Implications to Human Health

ABSTRACT

Particulate matter (PM) emissions from stationary combustion sources burning coal, fuel oil, biomass, and waste, and PM from internal combustion (IC) engines burning gasoline and diesel, are a significant source of primary particles smaller than 2.5 μm (PM_2.5) in urban areas. Combustion-generated particles are generally smaller than geologically produced dust and have unique chemical composition and morphology. The fundamental processes affecting formation of combustion PM and the emission characteristics of important applications are reviewed. Particles containing transition metals, ultrafine particles, and soot are emphasized because these types of particles have been studied extensively, and their emissions are controlled by the fuel composition and the oxidant-tem-perature-mixing history from the flame to the stack. There is a need for better integration of the combustion, air pollution control, atmospheric chemistry, and inhalation health research communities. Epidemiology has demonstrated that susceptible individuals are being harmed by ambient PM. Particle surface area, number of ultrafine particles, bioavailable transition metals, polycyclic aromatic hydrocarbons (PAH), and other particle-bound organic compounds are suspected to be more important than particle mass in determining the effects of air pollution. Time- and size-resolved PM measurements are needed for testing mechanistic toxicological hypotheses, for characterizing the relationship between combustion operating conditions and transient emissions, and for source apportionment studies to develop air quality plans. Citations are provided to more specialized reviews, and the concluding comments make suggestions for further research.