Postconsumer polyethylene terephthalate (PET)/polyolefin blends through reactive processing

Increasing awareness of environmental and energy problems has promoted greater governmental interest in selected waste collection and consequently has attracted the interest of several research groups to the challenge of converting recovered plastics into useful materials. The reactive blending of postconsumer polyethylene terephthalate (PET) with different polyolefins (PO) was studied in attempts to obtain a new material with enhanced properties with respect to the starting materials. The success of the project depends mainly on the possibility of obtaining a compatibilized blend between two starting polymers that, from chemical and thermomechanical viewpoints, are very different. This was approached by employing polyolefins bearing functional groups capable of specific interaction or chemical reaction with PET end groups. Ternary blends of very low density polyethylene (VLDPE)/PET/functionalized polyolefin (FPO) in a weight composition of 70/20/10 and binary blends of FPO/PET in a weight composition of 90/10 were prepared and studied to obtain reinforced polyolefin thermoplastic materials. Reactive blending was achieved in a Brabender Plastograph with a mixing chamber of 30 or 50cm³, at 250°C, and 40rpm for 10min. Differential scanning calorimetry, scanning electron microscopy, and tensile tests were used to investigate the phase behavior, the efficiency of compatibilization, and the mechanical properties of the blends.     

Thermal cracking of oils from waste plastics

Thermal cracking of decomposed waste plastic oil produces a good yield of olefins. The solvent extraction of such waste plastic oil seems to be efficient for increasing gas yields and recycling monomers. To assess the potential of monomer recovery from municipal waste plastics, the oils were cracked using a laboratory-scale quartz-tube reactor. The waste plastic oils were provided by two commercial plants of the Sapporo Plastic Recycle Co. and the Dohoh Recycle Center Co. in Japan. A model waste plastic oil made in a laboratory was also examined. Yields of ethene, propene, and other products were measured at different temperatures. Two-step pyrolysis reduces coking compared with the direct thermal degradation of plastics. The raffinates from waste plastic oils extracted by sulfolane were also cracked. The primary products were almost the same as those from nontreated oils. The maximum total gas yield was 78wt%–85wt% at 750°C, an increase of about 20wt% compared with that of nonextracted oil. Solvent extraction removes stable aromatic hydrocarbons such as styrene, which is more coked than cracked.     

Decomposition reactions of epoxy resin and polyetheretherketone resin in sub- and supercritical water

Epoxy resin and polyetheretherketone (PEEK) resin were decomposed into their monomers such as phenol, cresols, and their analogues by thermal treatment in sub- and supercritical water in a 10-ml tubing bomb reactor. The addition of basic compounds such as Na₂CO₃ was effective in promoting the decomposition reaction of the resins. In the reaction of epoxy resin, the yield of identified products reached 10% for the reaction at 703K over 1h. In the reaction of PEEK resin, the total yield of phenol and dibenzofuran reached 88% for the reaction at 703K over 3h. Chemical participation of water in the decomposition reaction was confirmed by the reaction of dinaphthylether.     

Pore structure and adsorption properties of activated carbon prepared from granular molded waste paper

We have previously manufactured activated carbon using waste paper board, which was prepared by adding 8% phenol resin adhesive to torn waste newspaper and hot-pressing. In this study, the pretreatment process of the raw material was simplified; the waste paper was extruded to form granules. The activated carbon was manufactured by the carbon dioxide activation method using the granules as the raw material. The properties of the activated carbon were evaluated based on the pore structure, the iodine adsorption number, and the adsorption of toluene vapor in a sealed chamber. The activated carbon, which was manufactured at an activation temperature of 1100°C and a treatment time of 60min, exhibited a specific surface area of 1241m²/g and an iodine adsorption number of 1120mg/g. These results were similar to those obtained for two commercially available activated carbons. The extent of toluene vapor adsorption by this activated carbon was similar to that observed for the two commercial activated carbons over a period of 130min.     

Landfill mining and waste characterization: a strategy for remediation of contaminated areas

This article describes landfill-mining tests, including excavation, screening, and fraction characterization, carried out in the Msalycke and Gladsax landfills for municipal solid waste (MSW) in Sweden. The excavated waste in these two sites was 17–22 and 23–25 years old, respectively. The main part of Msalycke was unaffected by degradation, and during excavations no substantial amount of biogas was detected. After screening, three size fractions were obtained: <18mm, 18–50mm, and >50mm. Soil amendment and anaerobic digestion with energy extraction are suggested for the first and second fraction, respectively. Incineration with energy recovery is possible with the third fraction after any coarse (inert) material is removed, and construction/demolition waste can easily be recycled provided that it is not contaminated by hazardous material. Excavated waste taken from different depths was also analysed and compared in relation to composition, calorific value, and leachate constituents.     

Solid State Reactions of Potato Starch with Urea and Biuret

Reaction of granular potato starch with urea and biuret resulted in the formation of products, which were soluble neither in cold nor boiling water. The net reaction was a monosubstitution of the hydrogen atom in one hydroxyl group in each D-glucose unit of starch with the either CO–NH₂ or CO–NH–CO–NH₂ moiety, respectively. Properties of the products, particularly these with urea, depended on the mode of reaction. Reactions were carried out in the microwave oven as well as with convection heating. The products retained the granular form of starch but a vast majority of granules were damaged. -Amylolysis of those materials revealed that their susceptibility to the enzyme increasing in the order: starch-amylolysis with simultaneous insolubility in water make these products suitable as ruminant fodder and, eventually, biodegradable material.     

Catalytic decomposition of hydrocarbon into hydrogen and carbon in a spouted-bed reactor as the second-stage reactor of a plastic recycling process

A two-stage process for the chemical recycling of plastics is proposed. In this process, which consists of two reactors, plastics are converted into hydrogen and carbon. In the first reactor, plastic chips are thermally decomposed into hydrocarbons. In the second reactor, the hydrocarbons formed in the first reactor are catalytically decomposed into carbon and hydrogen. In this study, in order to obtain basic data for the second reactor, propene was catalytically decomposed in a laboratory-scale spouted-bed reactor (600mm high, 21.6mm internal diameter, made of SUS304). The effect of the type of spouting medium used on the decomposition behavior of propene was investigated using four types of spouting medium (nickel-plated -alumina, palladium-plated -alumina, nickel-impregnated -alumina, and -alumina). The nickel-impregnated -alumina gave the best propene conversion and hydrogen yield.     

The contemporary copper cycle of Asia

A regional stock and flow model for an industrial metal was developed based on the substance-flow framework. Using this model, the contemporary copper cycle of the Asian region was constructed by aggregating country-level production and import and export data for different stages of the copper cycle. The reliability and availability of data were assessed both qualitatively and quantitatively. Asia as a region is a net importer of copper. There is a significant build-up of copper in use at a rate of nearly 3TgCu/year. The per capita generation of copper waste (0.4kgCu/(capita-year)) and the rate of secondary recovery of copper are low compared with Europe and North America. Japan's rates of use, waste generation, and recycling of copper are all much larger than the continental average. A tremendous potential exists in the region to utilize the copper content of the in-use reservoir, and subsequently to enhance copper recycling rates in the future. A set of metrics for the copper cycle is suggested in order to address sustainability issues related to resource policy and the environmental management of copper.     

Degradation of chlorinated dioxin in denitrifying activated sludge from leachate treatment plant of a landfill

The degradation rate of dioxins added to the activated sludge from a leachate treatment plant of a landfill under denitrification conditions was estimated using six bioreactors. Over 99% of the added dioxins (600ng) were degraded within 7 days. Furthermore, continuous cultivation was carried out for 1 month. The activated sludge degraded 600ng of dioxins (that is, all of the added dioxins) placed in each reactor every 7 days, and this activity was maintained for 35 days. Under aerobic conditions with this sludge, the dioxins were not degraded in 7 days, but 90% of the 600ng of dioxins was degraded in 35 days. The high level of activity observed in the present study may only occur under anaerobic conditions, especially under denitrifying conditions.     

The contemporary Oceania zinc cycle: one-year stocks and flows

The material flow approach provides a framework from which to address resource management and estimate gross environmental impacts, both spatially and temporally. In this article, the major flows of zinc in Oceania over its entire life-cycle are examined; these include production (mining, milling, and refining), fabrication and manufacturing of semi- and finished products, use, and the waste management system. Comprehensive mass balances were applied to determine the zinc flows, including the quantities of zinc entering stocks in waste and in-use reservoirs. The Oceania cycle shows that substantial amounts of zinc (about 1120Gg/year) are mined on the continent. The total flow of zinc in finished products entering the use stage is about 8.6kg/(capita.year), substantially exceeding the zinc flow in discarded products. This difference, about 7.2kgZn/(capita.year) on average, is added to the in-use reservoir, largely for galvanizing applications in domestic construction and transportation. Less than 60% of all discarded zinc entering the waste management system is recycled. Much of the remaining discarded zinc is diluted into other waste streams, where recovery and recycling are probably not economically feasible.     

Study on the conversion of waste plastics/petroleum resid mixtures to transportation fuels

Catalytic coprocessing of model and waste plastics with light Arabian crude oil residue was investigated using NiMo/Al₂O₃, ZSM-5, FCC, and hydrocracking catalysts. Reaction systems that were studied included low density polyethylene (LDPE), high density polyethylene (HDPE), polystyrene (PS), and polypropylene (PP). A series of single (plastic/catalyst) and binary (plastic/resid/catalyst) reactions were carried out in a 25-cm³ micro autoclave reactor under different conditions of weight and type of catalyst, duration, pressure, and temperature. The optimum conditions selected for our work were: 1% catalyst by weight of total feedstock weight, 60min reaction time, 8.3Mpa of H₂, and 430°C. The product distribution for the binary system using plastic and petroleum residue provided some encouraging results. High yields of liquid fuels in the boiling range of 100°–480°C and gases were obtained along with a small amount of heavy oils and insoluble material such as gums and coke. In general, this study helps to demonstrate the technical feasibility of upgrading both waste plastics and petroleum resid, as well as an alternative approach to feedstock recycling.     

What substances or objects should be recycled? The recycling legislative experience in Taiwan

The legislative framework of waste management in Taiwan has never been efficient, mainly due to unclear definitions and regulations. In 2002, this system was split into two parts by enacting a new law, the Resource Recycling and Re-use Act (RRRA). However, it then became more complicated and recycling effectiveness was impeded. The causes were mainly the unclear definitions, conflicts about the scope, and issues between the RRRA and the Waste Disposal Act (WDA). This article examines the recycling legislation experience in Taiwan, and proposes two modifications for resolving these problems. The first proposal is merging these two acts into one. The second proposed modification maintains a two-system structure but introduces a new subject, discards, into the law. The subject of discards is further categorized as recyclable resources or waste, which correspond to recycling operations and disposal operations, respectively. The new structures, interfaces, prerequisites, properties, and comparisons are also explained.     

Investigation of the Aerobic Biodegradability of Several Types of Cyclodextrins in a Laboratory-Controlled Composting Test

The biodegradation of several types of cyclodextrins (CDs) under laboratory-controlled composting conditions was investigated. CDs are used in a broad range of applications in food, pharmaceutical, medical, chemical, and textile industries because of their specific chemical characteristics related to their hydrophobic interior and hydrophilic exterior. The three naturally occurring cyclodextrins -CD, -CD, and -CD proved to be completely and readily biodegradable. Chemical modification of these basic compounds can have a major impact on the biodegradation rate and final biodegradation percentage. Fully acetylated -CD and -CD were found to be nonbiodegradable during 45 days of composting. Reducing the degree of acetylation had a positive effect on the biodegradation. Complete biodegradation was obtained for partially acetylated -CD with a degree of substitution (DS) of 7. The methylation (DS = 13) of -CD resulted in an undegradable compound during the 47 days composting, while (2-hydroxy)propyl--CD reached a plateau in biodegradation at a percentage of 20%. The incorporation of the antimicrobial agents imazalil and allyl-isothiocyanate into -CD had no negative impact on biodegradation, which makes these antimicrobial agents/CD complexes suitable for incorporation into biodegradable active packaging.     

Preparation conditions and swelling equilibria of biodegradable hydrogels prepared from microbial poly(γ-glutamic acid) and poly(ε-lysine)

Biodegradable hydrogels prepared by -irradiation from microbial poly(amino acid)s are reviewed. pH-sensitive hydrogels were prepared by means of -irradiation of poly(-glutamic acid) (PGA) produced byBacillus subtilis IFO3335 and poly(-lysine) (PL) produced byStreptomyces albulus in aqueous solutions. The preparation conditions, swelling equilibria, hydrolytic degradation, and enzymatic degradation of these hydrogels were studied. A hydrogel with a wide variety of swelling behaviors has been produced by -irradiation from a mixture solution of PGA and PL.Paper presented at the 4th International Workshop on Biodegradable Plastics and Polymers, October 11–14, 1995, Durham, New Hampshire, USA.     

The Impact of Conifer Harvesting on Stream Water Quality: A Case Study in Mid-Wales

A 12-year record of water quality data for runoff from a spruce forested hillslope with podzolic soils shows the impacts of conifer harvesting and replanting in relation to nitrate generation and its influence on surface water acidification. With felling, nitrate increases from a background of 18 Eq/l to about 50 Eq/l after 1 to 2 years and then declines to background levels over the next 1 to 2 years and to lower concentrations thereafter. This change is mirrored by an acidification process as manifest by a change in Gran alkalinity, acid neutralization capacity (ANC) and aluminium concentrations as well as pH. For example, Gran alkalinity and ANC, which start at negative concentrations prior to felling (about –20 and –50 Eq/l, respectively), become more negative (–30 and –100 Eq/l, respectively) at high nitrate concentrations. Correspondingly, pH decreases from about 4.7 to 4.5 and aluminium concentrations increase from about 14 to 16 M. Subsequently, the acidification is reversed as nitrate concentrations decline and after five years post-felling the system has higher pH, Gran alkalinity and ANC together with lower aluminium concentrations than even before the felling took place (the post-felling values are about 4.9, -15 Eq/l, –20 Eq/l and 7 M/l, respectively).Other determinands show clear changes over time. For example, there is a marked increase in sodium and chloride prior to and around the time of felling (200 to 300 and 230 to 400 Eq/l, respectively), with a subsequent decline in concentration to pre-felling and to lower values of around 160 and 170 Eq/l, respectively, thereafter. This change is probably associated with abnormally high inputs of sea-salts from the atmosphere during the first quarter of the year of felling, and dilution thereafter, rather than a direct consequence of the felling activity itself: this change in sea salt loading has had an impact on stream acidity. Dissolved organic carbon and iron also change with concentrations increasing over time (60 to 200 and 1.0 to 1.5 M/l, respectively) and this mirrors a general pattern observed across the Plynlimon catchments irrespective of whether or not there has been felling activity.The implications of the findings are discussed in relations to environmental management and hydrochemical processes.     

The Role Played by Acetyl Group Distribution Patterns in Substituted Starch Toward Enzymatic De-acetylation and Chain Fragmentation

The nature and distribution of the acetylated groups were evaluated by ¹³C-NMR and ¹H-NMR. The starch substrate with a DS of 1.5 comprises only two patterns: -(14)-d-glucopyranose and 2,3,6-tri-O-acetyl--(14)-d-glucopyranose. The starch with a DS of 3.0 also comprises two patterns: 2,3,4,6-tetra-O-acetyl--(14)-d-glucopyranose and 2,3,6-tri-O-acetyl--(14)-d-glucopyranose; whereas starch (DS = 1.9) contains 4 patterns: 2,3,6-tri-O-acetyl--(14)-d-glucopyranose, 2,3,4,6-tetra-O-acetyl--(14)-d-glucopyranose terminal, 2,6-di-O-acetyl--(14)-d-glucopyranose, and 3,6-di-O-acetyl--(14)-d-glucopyranose. Using esterase from Viscozyme, it has been possible to hydrolyze up to 7% of the DS 3.0 starch. An -amylase (Fungamyl 800) was then added to these acetylesterases. With a 2.4 FAU/mL fraction of -amylase and 2.4 U/mL from the Viscozyme's acetylesterase, 28% of the acetylated end groups were hydrolyzed for the starch substrates with DS 3.0. Moreover, a synergic action between -amylase and acetylesterase was noticed, allowing fragmentation of 32% for DS 1.5, 30% for DS 1.9, and 11% for DS 3.0.     

Biodegradability: An assessment of commercial polymers according to the Canadian method for anaerobic conditions

The degradation of several biodegradable polymers was measured as a result of exposure to an anaerobic medium. The polymers investigated included materials based upon polylactic acid, polylactone, and poly(hydroxy butyrate/valerate) as well as those incorporating starch-based materials. The degradation was monitored by methane and carbon dioxide evolution. In addition, the physical and chemical changes were noted as a result of exposure. These measurements included changes in mass, dimension, and molecular weight. FTIR, UV-vis, proton, and¹³C NMR spectra were also recorded prior to and after exposure. The results clearly indicated that several biological and chemical degradation processes were occurring with the biodegradable polymers studied.Paper presented at the Bio/Environmentally Degradable Polymer Society—Second National Meeting, August 19–21, 1993, Chicago, Illinois.Issued as NRCC No. 37549.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Soil Respiration in Relation to Small-Scale Patterns of Lead and Mercury in Mor Layers of Southern Swedish Forest Sites

Pollution-related lead (Pb) andmercury (Hg) in mor layers of Southern Swedenmight have effects on soil biology, although inthe literature effect concentrations have beenidentified at much higher levels. Considerablesmall-scale spatial variability in heavy metalcontents and microbial respiration in mor layersof forest sites was used to calculatecorrelations that could reveal toxic effects.Negative correlations were always strongest atsites with high loads of Pb or Hg, which was considered to indicate metal toxicity. The highload sites were found in Southwestern Sweden,locally at a motorway and at a chlorine-alkalifactory. Other factors of possible influence,such as other pollutants, age of organic materialor climatic differences, would affect high andlow load sites alike. Negative correlations withrespiration were found for Pb at sites with 74 g g^-1 of mean Pb content in O_f-layer and for Hg at 0.25 g g^-1.     

Effect of Starch Granule Size on Viscosity of Starch-Filled Poly(hydroxy ester ether) Composites

The effect of starch granule size on the viscosity of starch-filled poly(hydroxy ester ether) (PHEE) composites was characterized using size-fractionated potato starch, as well as unfractionated starches (rice, corn, wheat, and potato). Potato starch was separated using an air classifier into four particle size fractions: <18 m, 18-24 m, 24-30 m, and >30 m. The starch was dried to a moisture content of 0.5% to minimize moisture effects on composite rheology. PHEE and potato starch were extruded with starch volume fractions of 0.46 and 0.66. Stress relaxation, frequency and strain sweep, and temperature-dependence measurements were carried out. Although small variations in viscosity were seen with the different potato starch fractions, differences were not significant at a volume fraction of 0.46. Viscosity differences between the different particle size fractions were more pronounced at a volume fraction of 0.66. The temperature dependence could be described by an Arrhenius relation, with an apparent activation energy of 84 kJ/mole. At a volume fraction of 0.46, the starch/PHEE viscosities increased in the order potato starch < wheat starch corn starch < rice starch.