Measurements of ammonia concentrations,fluxes and dry deposition velocities to a spruce forest 1991–1995

The dry deposition velocities and fluxes of ammonia have been estimated from measurements of the vertical gradient of ammonia and micrometeorology above a spruce forest in western Jutland, Denmark. Measurements have been made in seven periods, each lasting about one week and covering all seasons and different meteorological situations. Different deposition characteristics were observed, depending on the ammonia concentration and the relative humidity. At conditions with westerly winds, the wind brings air masses from the North Sea with low concentration levels of ammonia to the site, while at conditions with easterly winds, the air have passed central Jutland with large emission areas. Some of the relatively low deposition velocities or emissions were observed during conditions with low ammonia concentration and westerly winds. These observations might relate to a compensation point of the forest, i.e. an ammonia concentration below which the trees and/or the surface emit ammonia due to an equilibrium with the ammonia inside the needles or on the surface. Emission of ammonia was also observed at relatively high ammonia concentration levels (above 2 μg NH₃–N m^-3), mainly during one measuring period characterized by easterly winds with dry conditions and high ammonia concentrations, and the emissions might relate to evaporation from ammonia saturated surfaces or emission from mineralization in the forest soil. In general, relatively high net deposition velocities were observed during conditions with relative humidity above 80% or at ammonia concentrations moderate higher than a given (temperature dependent) compensation point. During stable conditions some observations revealed that the gradient above the canopy not necessarily represents the exchange with the canopy.     

Resuspension of small particles from tree surfaces

A detailed study of resuspension of 1.85 μm MMAD silica particles from five horizontal layers within a small scale spruce canopy was carried out in a wind tunnel in which saplings were exposed to a constant free stream wind speed of 5 m s⁻¹. This provided quantitative estimates of the potential for a tree canopy contaminated with an aerosol deposit to provide (i) an airborne inhalation hazard within the forest environment and (ii) a secondary source of airborne contamination after an initial deposition event. Resuspension occurred with a flux of 1.05×10⁻⁷ g m⁻² s⁻¹ from spruce saplings initially contaminated at a level of 4.1×10⁻² g m⁻². An average resuspension rate (Λ) of 4.88×10⁻⁷ s⁻¹ was obtained for the canopy as a whole. Values of Λ were significantly different (ANOVA, p<0.001) between canopy layers and Λ was markedly greater at the top of the canopy than lower down although there was a slight increase in Λ at the base of the canopy. The resuspended silica particles deposited onto the soil surface at an average rate of about 5.3×10⁻⁸ μg cm⁻² s⁻¹. It is concluded that resuspension under wind velocities similar to that used in the reported experiments is likely to pose a relatively small inhalation hazard to humans and a relatively minor source of secondary contamination of adjacent areas. Furthermore, resuspension rates are likely to diminish rapidly with time. The results are discussed in relation to the growing interest in the tree planting schemes in urban areas to reduce the impacts of air pollution.     

Dry deposition to a uniform canopy: Evaluation of a first-order-closure mathematical model

A mathematical model is developed for the transport of momentum and matter within a canopy consisting of identical elements protruding vertically from a smooth substrate. Turbulent flux is modelled using a mixing-length approach. The loss of momentum (or matter) to individual elements is related to the mean wind speed, and the element-element interaction via the turbulent wind field is represented by a sheltering factor. Careful consideration is given to the formulation of lower boundary conditions. The model assumptions are compared with those of other models.The model predictions are compared with measurements on a vertically- and horizontally-uniform artificial canopy in a wind-tunnel. The model reproduces well the observed relationship between the parameters of the logarithmic wind speed profile above the canopy and the observed deposition velocities of thorium-B (ThB) atoms and particles in the diameter range 0.08–32 μm, using a sheltering factor which is little dependent on wind speed and has the same magnitude for momentum, gas and particles. The predicted dependences of deposition velocity on friction velocity and, for particles, on diameter shed light on the performance of semi-empirical correlations proposed in the literature. For ThB atoms, the calculated deposition velocities are compared with those of other mathematical canopy models: a comparable degree of agreement is obtained here with fewer free parameters.The fraction of deposit on the substrate is underpredicted by an order of magnitude in some cases, pointing to the limitations of the modelling of conditions near the substrate in terms of quasi-shear flow.     

Simulation of boundary layer trajectory dispersion sensitivity to soil moisture conditions: MM5 and Noah-based investigation

In this study, the sensitivity of trajectory paths to anomalous soil moisture was analyzed during three different synoptic episodes in June 2006. The MM5 and Noah land surface models were used to simulate the response of the planetary boundary layer. The HYSPLIT model was used for trajectory analysis. It was found that the response in horizontal lower-level wind field was larger at regions where vertical wind velocity changes were also large. In addition, the sensitivity to soil moisture changes was significant and localized where convective activity was well developed and synoptic effects did not dominate. A non-local effect was felt over the rest of the domain where convection was not present since the model atmosphere reacted as a whole to compensate for induced changes in vertical velocity. This finding was supported by the fact that domain averaged vertical velocities changes were of the order of 0.2 cm s^?1 or less at about 650 hPa and about 200 times smaller than modeled local vertical velocity changes. The largest change in horizontal wind field near the surface was found for weak synoptic events on June 11–12 and June 22–23 while the stronger synoptic event of June 17–18 showed smaller differences. These changes in wind field conditions impacted the transport and dispersion of pollutants. To quantify the sensitivity of air quality estimates to soil moisture uncertainty, we have used three well known measures of trajectory differences: the absolute horizontal transport deviation (AHTD), the relative horizontal transport deviation (RHTD) and the absolute vertical transport deviation (AVTD) for an ensemble of 98 trajectories departing from a region well within the computational domain. For the June 11–12 event it was found that for wet and dry soil moisture experiments, AHTD, RHTD, and AVGTD can reach values in the range 60–100 km, 10–20% and 500–900 m at 24 h run time, respectively. For the June 17–18 and June 22–23 events these values of trajectory differences were reduced more than half. These differences in behavior between time periods are largely attributed to the combined effects of synoptic forcing and the sensitivity of planetary boundary layer to soil moisture changes during well developed convection. The implication for air quality studies is that the soil moisture anomaly and related uncertainty in planetary boundary layer response needs to be incorporated in order to construct an ensemble of the most probable scenarios in which pollutants are released and transported throughout a given target region.     

Combined effect of boundary layer recirculation factor and stable energy on local air quality in the Pearl River Delta over southern China

Atmospheric boundary layer (ABL) has a significant impact on the spatial and temporal distribution of air pollutants. In order to gain a better understanding of how ABL affects the variation of air pollutants, atmospheric boundary layer observations were performed at Sanshui in the Pearl River Delta (PRD) region over southern China during the winter of 2013. Two types of typical ABL status that could lead to air pollution were analyzed comparatively: weak vertical diffusion ability type (WVDAT) and weak horizontal transportation ability type (WHTAT). Results show that (1) WVDAT was featured by moderate wind speed, consistent wind direction, and thick inversion layer at 600~1000 m above ground level (AGL), and air pollutants were restricted in the low altitudes due to the stable atmospheric structure; (2) WHTAT was characterized by calm wind, varied wind direction, and shallow intense ground inversion layer, and air pollutants accumulated in locally because of strong recirculation in the low ABL; (3) recirculation factor (RF) and stable energy (SE) were proved to be good indicators for horizontal transportation ability and vertical diffusion ability of the atmosphere, respectively. Combined utilization of RF and SE can be very helpful in the evaluation of air pollution potential of the ABL.

Implications: Air quality data from ground and meteorological data collected from radio sounding in Sanshui in the Pearl River Delta showed that local air quality was poor when wind reversal was pronounced or temperature stratification state was stable. The combination of horizontal and vertical transportation ability of the local atmosphere should be taken into consideration when evaluating local environmental bearing capacity for air pollution.     

Efficiency of deposition of pesticide droplets on flat cards and spheres

Abstract

The mass flux of a cloud of droplets heading towards a collector can be decomposed into its horizontal and vertical components. While only the vertical mass flux contributes to droplet deposition on a flat card by the mechanism of sedimentation, both flux components contribute to deposition on a sphere by both mechanisms of inertial impaction and sedimentation. Calculated collection efficiencies decrease as wind speed increases for cards but as wind speed increases for spheres, a minimum collection efficiency is reached at a certain wind speed. The average collection efficiencies, as measured in the field trial portion of this study, are highly linearly correlated with wind speed for cards. For spheres, however, no correlation was found between the average collection efficiency and wind speed.     

Plume Dispersion in a Mountainous River Valley during Spring

The dispersion of hot plumes emitted from a smelter complex located In the Columbia River Valley, British Columbia, was evaluated under stable and neutral conditions during two mornings In spring. Spatial measurements of SO₂ and temperature within the plume were obtained by immersion probing using fast response helicopter and automobile mounted Instrumentation. In addition, meteorological measurements of vertical wind and temperature profiles at, and downwind from, the smelter were obtained from minisonde balloon releases. With weak down-valley winds, it was found that the plume axis elevations were generally lower during both stable and neutral conditions than would be predicted by Briggs plume-rise formulae. In contrast, plume dispersion, although confined in the horizontal by the steep valley walls during both stability regimes, was significantly enhanced by exceptionally good lateral mixing, particularly close to the source.     

Droplet size spectra and deposits of two aerially sprayed Bacillus thuringiensis formulations on artificial samplers and live foliage

Abstract

Two commercial formulations of Bacillus thuringiensis var. kurstaki (BTK), Foray^® 48B and Thuricide^® 48LV, were applied aerially over nine spray blocks in a hardwood forest in West Virginia in 1991. Droplet spectra and spray mass deposits were determined using water‐sensitive paper strips (WSPS), glass micro‐fiber filters (GMFFs), glass plates and castor oil. Mass deposits of BTK were also assessed on natural foliage by two bioassay methods, i.e., feeding of homogenized foliage containing a starch‐sucrose solution and force‐feeding bioassay of foliar extracts containing re‐dissolved protein precipitate. Deposits on canopy foliage and ground samplers were also assessed by total protein assay and enzyme‐linked immunosorbent assay (ELISA). Droplet spectra on the WSPS were different from those on castor oil. Droplets on horizontal ground WSPS were larger than those on vertical ground WSPS. WSPS placed at canopy level collected more droplets than those at ground level. The total protein deposits (ng/cm²) were consistently higher on all blocks than the delta‐endotoxin protein deposits. Spray mass recovery on the ground samplers were low, and ranged from 2.9 to 8.0% of the applied rates.     

Aerosol load study in urban area by Lidar and numerical model

Vertical profiles of particle mass concentration in the urban canopy above the city of Lyon have been obtained from Lidar measurements of atmospheric backscattering, over a period of three days. The concentrations measured at 50 m above the ground have been compared with the mass concentration of PM10 measured by a ground-based sampler located near the Lidar site. At certain times during the measurement campaign, the Lidar concentration measurements at 50 m agree reasonably well with the concentrations at ground level but at other times the differences between the two sets of measurements are so great that they cannot be explained by possible uncertainties in the data processing. Even when the Lidar and ground-based measurements coincide, there are significant differences between the two signals. To explain these differences we have computed the trajectories of the air parcels that pass over the Lidar, using a numerical model for the wind field that takes into account surface features such as relief and changes in roughness. This analysis showed that the differences can be explained by the meteorological conditions (wind speed and direction, vertical profiles of temperature) and the positions of the different sources of particulate matter relative to the measurement site. The combination of Lidar, ground-based sampler and air mass trajectory calculations is shown to be a powerful tool for discriminating between different sources of pollution, which could be useful in enforcing an urban air quality policy.     

Episodes of high SO2 concentration in The Netherlands

In episodes of high daily mean SO₂ concentrations in the atmosphere there is a very extensive concentration field over The Netherlands caused by influx from both the Ruhr area and Central Europe. The meteorological conditions for such episodes range from very stable to stable with a boundary layer height between 100 and 450 m, wind speed at 200 m between 0 and 18 m s⁻¹ and at 20 m between 0 and 9 m s⁻¹. The last figures indicate that transport, as well as transport combined with stagnation, causes the high concentrations. The episodes nearly all occur in December, January and February, with easterly winds. In two thirds of the cases a local snow cover is present. This cover is more extensive in the east, so probably in all cases there is reduced dry deposition of SO₂. The turbulence is very low with hardly any vertical dispersion at higher altitudes, except around noon. In consequence of the wind direction variations over a day and the wind direction shear, the daily horizontal dispersion is normal or larger than normal. Therefore the contribution of a local high point source in The Netherlands to the ground level concentration will be small during air pollution episodes in winter.     

Aerosol properties,in-canopy gradients,turbulent fluxes and VOC concentrations at a pristine forest site in Amazonia

Aerosol physical and chemical properties were measured in a forest site in central Amazonia (Cuieiras reservation, 2.61S; 60.21W) during the dry season of 2004 (Aug–Oct). Aerosol light scattering and absorption, mass concentration, elemental composition and size distributions were measured at three tower levels (Ground: 2 m; Canopy: 28 m, and Top: 40 m). For the first time, simultaneous eddy covariance fluxes of fine mode particles and volatile organic compounds (VOC) were measured above the Amazonian forest canopy. Aerosol fluxes were measured by eddy covariance using a Condensation Particle Counter (CPC) and a sonic anemometer. VOC fluxes were measured by disjunct eddy covariance using a Proton Transfer Reaction Mass Spectrometer (PTR-MS). At nighttime, a strong vertical gradient of phosphorus and potassium in the aerosol coarse mode was observed, with higher concentrations at Ground level. This suggests a source of primary biogenic particles below the canopy. Equivalent black carbon measurements indicate the presence of light-absorbing aerosols from biogenic origin. Aerosol number size distributions typically consisted of superimposed Aitken (76 nm) and accumulation modes (144 nm), without clear events of new particle formation. Isoprene and monoterpene fluxes reached respectively 7.4 and 0.82 mg m^?2 s^?1 around noon. An average fine particle flux of 0.05 ± 0.10 10⁶ m^?2 s^?1 was calculated, denoting an equilibrium between emission and deposition fluxes of fine mode particles at daytime. No significant correlations were found between VOC and fine mode aerosol concentrations or fluxes.     

A wind tunnel study of dense gas dispersion in a neutral boundary layer over a rough surface

Measurements of the vertical entrainment velocity into two-dimensional dense gas plumes over fully rough surfaces were carried out as part of a co-operative research programme with wind tunnel facilities in the USA. This paper presents results obtained for neutral boundary layer conditions in the EnFlo wind tunnel at the University of Surrey; a companion paper treats the stable boundary layer case. Entrainment velocities, W_E, were deduced from the streamwise development of the concentration field, non-dimensionalised with respect to the friction velocity in the undisturbed flow, u^*, and correlated with the plume Richardson number, Ri^*. Results for Richardson numbers in the range Ri^*<15 were found to be well fitted by the empirical expression: W_E/u^*=0.65/(1+0.2Ri^*). Flow visualisation studies showed layered plume structures with a sharp upper interface at higher Richardson numbers and in this regime turbulent motion below the interface became progressively more intermittent as Ri^* increased. Measured turbulence levels collapsed within such high Richardson number plumes and flow and dispersion were significantly affected by molecular processes. Up-welling above the source was observed when the emission speed exceeded the approach flow friction velocity, though there was no clear evidence that this affected plume behaviour away from the immediate vicinity of the source.     

Tracer diffusion from a horizontal fracture into the surrounding matrix: measurement by computed tomography

The vertical diffusion of NaI solution from a horizontal fracture into and within the surrounding matrix was tracked and quantified over time using an artificially fractured chalk core (30x5 cm) and a second-generation X-ray computed tomography (CT) scanner. The different tracer-penetration distances imaged in the matrix above and below the horizontal fracture are indicative of a greater tracer mass penetrating into the lower matrix. The enhanced transport in the matrix below the fracture was related to the Rayleigh-Darcy instability induced by the density differences between the heavier tracer solution in the fracture (1.038) and the distilled water that had initially resided in the matrix. Our observations suggest that below the fracture, the tracer is propagated by an advection-diffusion process that is characterized by both higher rates and higher concentrations relative to its propagation by diffusion above the fracture. The experimental results suggest that the prediction of contaminant migration in a rock intersected by both vertical and horizontal (e.g. along bedding planes) fractures is difficult because of density effects that result in different solute-penetration rates.     

Atmospheric Tracer Techniques and Gas Transport in the Primary Aluminum Industry

The results of 35 Individual SF₆ tracer tests conducted in Norway during 1978 demonstrate the applicability of tracer techniques to the study of a wide variety of pollutant transport problems found in the primary aluminum industry. Tracer methods were employed to determine the efficiency of the pollutant control system over a single reduction cell under a variety of operating conditions. Two tests conducted during normal operation gave efficiencies equal to 100 ±19% and 79 ± 12%, while a test performed during the occurrence of an anode effect yielded an efficiency equal to 66 ± 22%.

Tracer investigations of flow in the wake of a smelter hall indicated that between 1 % and 11 % of secondary, roof-top emissions can become entrained in the recirculation cavity and reenter the hall through the ventilation fresh air supply. These reentry rates were observed for release heights as high as 8 m above the existing roof exhaust duct. Tracer dispersion data collected within 20 building heights of the smelter agreed very well with extrapolations of McEIroy- Pooler dispersion curves for an urban area. Dispersion curves determined from a previous wind tunnel study of flow downwind of an isolated building underestimated dispersion downwind of the vs.melter complex.

The total fluoride mass flow rate measured downwind of a smelter during wet, foggy conditions indicated that wet removal rates of fluorides are in the range 3.2 × 10^?4/s to 6.4 × 10^?4/s. Simulation of the source with several tracer point releases and simultaneous measurement of fluoride and tracer ground-level concentrations downwind of the smelter eliminated the need for measurements of vertical profiles of wind speed and fluoride concentration during the experiment.     

Sub-canopy deposition of ozone in a stand of cutleaf coneflower

Although there has been a great deal of research on ozone, interest in exposure of native, herbaceous species is relatively recent and it is still not clear what role the pollutant has in their ecological fitness. The ozone exposure of a plant is usually expressed in terms of the concentration above the canopy or as a time-weighted index. However, to understand the physiological effects of ozone it is necessary to quantify the ozone flux to individual leaves as they develop, which requires knowing the deposition velocity and concentration of the pollutant as a function of height throughout the plant canopy. We used a high-order closure model of sub-canopy turbulence to estimate ozone profiles in stands of cutleaf coneflower (Rudbeckia laciniata L.) located in the Great Smoky Mountains National Park, USA. The model was run for periods coinciding with a short field study, during which we measured vertical concentration profiles of ozone along with measurements of atmospheric turbulence and other meteorological and plant variables. Predictions of ozone profiles by the model are compared with observations throughout the canopy.     

Salinity of marine aerosols in a Brazilian coastal area—Influence of wind regime

This paper presents salinity data of marine aerosols in a Brazilian coastal area at sites closer to the shore and discusses the influence of wind regime. Results show that measurements of marine salt deposition are strongly influenced by wind speeds above the critical value of 3.0 m s⁻¹. Although there is no agreement in literature yet as to how much this threshold is, the level of 3.0 m s⁻¹ is similar to the one found in a study carried out in Spain. An exponential variation of salt concentration with wind speed is presented in previous published papers. However, in the studied case, another relationship is proposed, which is based on chloride deposition on the wet candle device and wind speeds higher than 3.0 m s⁻¹ weighted by the accumulated time in which these wind speeds are observed, what seems to be particularly useful when wind speed ranges around the critical value.     

KAPPA-G,A Non-Gaussian Plume Dispersion Model: Description and Evaluation Against Tracer Measurements

This paper presents a mixed methodology for the simulation of atmospheric disperson phenomena in which vertical diffusion is computed using an analytical solution of the K-theory equation, while horizontal diffusion is simulated by the Gaussian formula. This new formulation, while maintaining a simple analytical form for the concentration field, incorporates the effects of power-law vertical profiles of both wind speed and eddy diffusivity. The performance of this approach, which has been implemented into a full computer package (KAPPA-G), is evaluated by comparison with data from SF₆ tracer experiments.     

Application of HYDRUS 1D model for assessment of phenol–soil adsorption dynamics

Laboratory-scale batch, vertical, and horizontal column experiments were conducted to investigate the attenuative capacity of a fine-grained clayey soil of local origin in the surrounding of a steel plant wastewater discharge site in West Bengal, India, for removal of phenol. Linear, Langmuir, and Freundlich isotherm plots from batch experimental data revealed that Freundlich isotherm model was reasonably fitted (R ²?=?0.94). The breakthrough column experiments were also carried out with different soil bed heights (5, 10, and 15 cm) under uniform flow to study the hydraulic movements of phenol by evaluating time concentration flow behavior using bromide as a tracer. The horizontal migration test was also conducted in the laboratory using adsorptive phenol and nonreactive bromide tracer to explore the movement of solute in a horizontal distance. The hydrodynamic dispersion coefficients (D) in the vertical and horizontal directions in the soil were estimated using nonlinear least-square parameter optimization method in CXTFIT model. In addition, the equilibrium convection dispersion model in HYDRUS 1D was also examined to simulate the fate and transport of phenol in vertical and horizontal directions using Freundlich isotherm constants and estimated hydrodynamic parameters as input in the model. The model efficacy and validation were examined through statistical parameters such as the coefficient of determination (R ²), root mean square error and design of index (d).     

Investigation of air pollution distribution in Linz: case studies to evaluate a K-type diffusion model coupled with a mass-consistent wind model

An Eulerian diffusion model coupled with a refined mass consistent wind model is developed for the operational forecasting of pollution distribution in complex terrain. The model is evaluated for a city situated in complex terrain. The study is carried out for a 20×20 km² area surrounding Linz, one of the industrial cities of Austria. The models are initialized with routinely measured meteorological parameters and topology information derived from the Geographical Information Systems (GIS). Four case studies, representative for major pollution episodes, are presented for model evaluation. The case studies include presence of a thermally induced wind system, presence of cold front an easterly southeasterly flow and a westerly–northwesterly flow. In presence of thermally induced wind systems, the flow field is most complex and existence of a shallow mixed layer with residual layer aloft enhances the pollution levels inside the city. Second case is used to study the development of pollution distribution inside the city in presence of low-level inversions and associated with low surface wind speeds. The low wind speeds in the surface layer lead to less mechanical generation of turbulence and lateral transport. The case studies of easterly and westerly flow fields are carried out to assess the capability of model under most frequently observed meteorological situations. The model is able to reproduce the pollution distribution near the slopes. There were over prediction inside the city in presence of thermally induced wind systems and is attributed to inadequate model physics during convective case. The present model setup is found to be a useful tool for the routine forecasting of pollution and could also be tested for other complex terrains.