Selective leaching of atmospheric aerosols: Resolution of limestone and cement

Samples of cement, limestone and soil aerosols prepared in our laboratory were tested for the aqueous solubility of Ca, Mg, Al, Fe and Si. While these elements were found to be practically non-leachable by water from soil, approximately 90% of Ca and 60% of Mg were extractable from cement and limestone aerosols. About 80% of Al and almost all the Si were also teachable from the cement aerosols. A method was developed for resolving limestone and cement aerosols from soil using water-soluble Ca and Mg as their marker elements. Furthermore cement and limestone could be resolved from one another using watersoluble Al (and/or Si) as the marker element of cement. The method was successfully tested on ambient aerosols collected near three cement factories. In the water extracts of these samples, a linear relationship was observed between Ca and Mg, the slope for which was in accordance with that expected for limestone and cement. Similarly, the insoluble Ca and Mg (obtained by subtracting Ca and Mg in the water extract from the total) showed a linear relationship with the insoluble Al. Their slopes were again typical of those reported for soils. This study demonstrated that selective leaching can be used to determine cement, limestone and soil components in ambient aerosols. Selective leaching with other solvents may enable a more complete apportionment of atmospheric aerosol sources.     

Source apportionment of surfactants in marine aerosols at different locations along the Malacca Straits

This study aims to determine the source apportionment of surfactants in marine aerosols at two selected stations along the Malacca Straits. The aerosol samples were collected using a high volume sampler equipped with an impactor to separate coarse- and fine-mode aerosols. The concentrations of surfactants, as methylene blue active substance and disulphine blue active substance, were analysed using colorimetric method. Ion chromatography was employed to determine the ionic compositions. Principal component analysis combined with multiple linear regression was used to identify and quantify the sources of atmospheric surfactants. The results showed that the surfactants in tropical coastal environments are actively generated from natural and anthropogenic origins. Sea spray (generated from sea-surface microlayers) was found to be a major contributor to surfactants in both aerosol sizes. Meanwhile, the anthropogenic sources (motor vehicles/biomass burning) were predominant contributors to atmospheric surfactants in fine-mode aerosols.     

Water-soluble ions in nano/ultrafine/fine/coarse particles collected near a busy road and at a rural site

This study investigated water-soluble ions in the sized particles (particularly nano (PM(0.01-0.056))/ultrafine (PM(0.01-0.1))) collected using MOUDI and Nano-MOUDI samplers near a busy road site and at a rural site. The analytical results demonstrate that nano and coarse particles exhibited the highest (16.3%) and lowest (8.37%) nitrate mass ratios, respectively. The mass ratio of NO(3)(-) was higher than that of SO(4)(2-) in all the sized particles at the traffic site. The secondary aerosols all displayed trimodal distributions. The aerosols in ultrafine particles collected at the roadside site exhibited Aitken mode distributions indicating they were of local origin. This finding was not observed for those ultrafine particles collected at the rural site. The mass median diameters (MMDs) of the nano, ultrafine, and fine particles were smaller at the traffic site than at the rural site, possibly related to the contribution of mobile engine emissions.     

A methodology to establish the morphology of ambient aerosols

The morphology of ambient particulate matter (PM) is an important characteristic that seldom is measured and reported. A study was performed to determine the viability of a method to establish the distribution of shapes and the fractal dimensions of aggregates of ambient aerosols. Particles of PM with aerodynamic diameter less than or equal to 2.5 microm (PM2.5) were captured on different days via size-independent electrostatic precipitation at two sites in St. Louis and examined in a scanning electron microscope (SEM). Nonvolatile particles between 0.1 and 2.5 microm were readily identified via SEM. Particle shapes were classified as fibrous, spherical, agglomerated, or "other." A computer program using the nested-squares algorithm was developed and used to determine the fractal dimensions of the aggregates. More particles were collected at the St. Louis-Midwest Supersite on June 14, 2002, than were collected on the Washington University campus loading dock on May 31, 2002, but the campus samples had a higher percentage of aggregates. On one day of sampling at the Supersite, the aggregate fraction was highest in the morning (14.3% between 7:00 and 9:00 a.m.) and steadily declined during the day (1.3% between 5:00 and 7:00 p.m.). The fractal dimensions of the aerosols were 1.65 in the morning (7:00-9:00 a.m.), decreased to 1.49 (11:00 a.m.-1:00 p.m.), and then increased to 1.87 (5:00-7:00 p.m.). The results show that the fractal dimension is not a static value and that ambient aerosols are not perfectly spherical.     

Aerosol characters from the desert region of Northwest China and the Yellow Sea in spring and summer: observations at Minqin,Qingdao, and Qianliyan in 1995–1996

Aerosol samples were collected from Northwest China desert region (Minqin), coastal suburb (Qingdao) and interior of the Yellow Sea (Qianliyan) in spring and summer of 1995 and 1996. Samples were analysed for major components, carbon and sulphur. The results show that concentrations of aerosols change considerably in time and space. The crustal materials carried by cold front system increase notably the aerosol concentration (mass/unit vol.) over the Yellow Sea but reduce the percentage contribution of pollutants and sea-salt. The sea-salt and regional aerosols become dominant fractions in coastal atmosphere in summer when the dust storms are expired in source region and the Southeast monsoon starts in the Pacific Ocean.     

Effects of aerosol species on atmospheric visibility in Kaohsiung City, Taiwan

Visibility data collected from Kaohsiung City, Taiwan, for the past two decades indicated that the air pollutants have significantly degraded visibility in recent years. During our study period, the seasonal mean visibilities in spring, summer, fall, and winter were only 5.4, 9.1, 8.2, and 3.4 km, respectively. To ascertain how urban aerosols influence the visibility, we conducted concurrent visibility monitoring and aerosol sampling in 1999 to identify the principal causes of visibility impairments in the region. In this study, ambient aerosols were sampled and analyzed for 11 constituents, including water-soluble ions and carbon materials, to investigate the chemical composition of Kaohsiung aerosols. Stepwise regression method was used to correlate the impact of aerosol species on visibility impairments. Both seasonal and diurnal variation patterns were found from the monitoring of visibility. Our results showed that light scattering was attributed primarily to aerosols with sizes that range from 0.26 to 0.90 pm, corresponding with the wavelength region of visible light, which accounted for approximately 72% of the light scattering coefficient. Sulfate was a dominant component that affected both the light scattering coefficient and the visibility in the region. On average, (NH4)2SO4, NH4NO3, total carbon, and fine particulate matter (PM2.5)-remainder contributed 53%, 17%, 16%, and 14% to total light scattering, respectively. An empirical regression model of visibility based on sulfate, elemental carbon, and humidity was developed, and the comparison indicated that visibility in an urban area could be properly simulated by the equation derived herein.     

Quantification and radiocarbon source apportionment of black carbon in atmospheric aerosols using the CTO-375 method

To make progress towards linking the atmosphere and biogeosphere parts of the black carbon (BC) cycle, a chemothermal oxidation method (CTO-375), commonly applied for isolating BC from complex geomatrices such as soils, sediments and aquatic particles, was applied to investigate the BC also in atmospheric particles. Concentrations and ¹⁴C-based source apportionment of CTO-375 based BC was established for a reference aerosol (NIST RM-8785) and for wintertime aerosols collected in Stockholm and in a Swedish background area. The results were compared with thermal–optical (OC/EC) measurements. For NIST RM-8785, a good agreement was found between the BC_CTO-375 concentration and the reported elemental carbon (EC) concentration measured by the “Speciation Trends Network—National Institute of Occupational Safety and Health” method (EC_NIOSH) with BC_CTO-375 of 0.054±0.002 g g⁻¹ and EC_NIOSH of 0.067±0.008 g g⁻¹. In contrast, there was an average factor of ca. 20 difference between BC_CTO-375 and EC_NIOSH for the ambient Scandinavian wintertime aerosols, presumably reflecting a combination of BC_CTO-375 isolating only the recalcitrant soot-BC portion of the BC continuum and the EC_NIOSH metric inadvertently including some intrinsically non-pyrogenic organic matter. Isolation of BC_CTO-375 with subsequent off-line radiocarbon analysis yielded fraction modern values (fM) for total organic carbon (TOC) of 0.93 (aerosols from a Swedish background area), and 0.58 (aerosols collected in Stockholm); whereas the fM for BC_CTO-375 isolates were 1.08 (aerosols from a Swedish background area), and 0.87 (aerosols collected in Stockholm). This radiocarbon-based source apportionment suggests that contribution from biomass combustion to cold-season atmospheric BC_CTO-375 in Stockholm was 70% and in the background area 88%.     

Phase transition behaviour of sodium oleate aerosol particles

Field measurements have shown that organic surfactants are significant components of atmospheric aerosols. While fatty acids, among other surfactants, are prevalent in the atmosphere, the influence of these species on the chemical and physical properties of atmospheric aerosols remains not fully characterized. In order to assess the phase in which particles may exist, a detailed study of the deliquescence of a model surfactant aerosol has been carried out. Sodium oleate was chosen as a surfactant proxy relevant in atmospheric aerosol. Sodium oleate micelle aerosol particles were generated nebulizing a sodium oleate aqueous solution. In this study, the water uptake and phase transition of sodium oleate aerosol particles have been studied in a room temperature aerosol flow tube system (AFT) using Fourier transform infrared (FTIR) spectroscopy. Aerosol morphology and elemental composition were also analysed using scanning electron microscopy/energy dispersive X-ray analysis (SEM/EDX) techniques. The particles are homogeneously distributed as ellipsoidal-shape aggregates of micelles particles with an average size of ∼1.1 μm. The deliquescence by the sodium oleate aerosol particles was monitored by infrared extinction spectroscopy, where the dried aerosol particles were exposed to increasing relative humidity as they passed through the AFT. Observations of the infrared absorption features of condensed phase liquid water enable to determine the sodium oleate deliquescence phase transition at 88±2%.     

Organic aerosols in the Miami area, USA: temporal variability of atmospheric particles and wet/dry deposition

Atmospheric particulate matter and both wet and dry deposition was collected over a period of nine months at one location in the metropolitan area of Miami, Florida. Molecular distributions and concentrations of n-alkanes, fatty acids, polycyclic aromatic hydrocarbons (PAHs) and hopanes were determined using weekly composite samples over this time period in order to determine temporal variability, and their possible dependence on climatic parameters such as temperature, rainfall and wind direction and frequency. Based on molecular distributions of the compounds studied, potential emission sources for the atmospheric particles were assessed and suggested to be mainly derived from automobile exhaust and natural sources. Although wet and dry deposition processes were observed to remove about equal amounts of organic aerosols from the Miami atmosphere, dry deposition was dominant in the removal of anthropogenically derived compounds such as PAHs and hopanes. Only very limited seasonal trends were observed, while wind direction and frequency was found to be the most important meteorological parameter controlling the temporal variability of the organic aerosols. This is the first detailed report of this nature for the Miami area.     

Impact of the tropical storm Delta on the gross alpha,gross beta, 90Sr, 210Pb, 7Be, 40K and 137Cs activities measured in atmospheric aerosol and water samples collected in Tenerife (Canary Islands)

On 28 and 29 November 2005, the tropical storm Delta struck the Canary Islands (Spain) and the western shores of Morocco. Gravimetric and radiometric measurements carried out in atmospheric aerosol and water samples, collected after the storm, showed increased levels of total suspended particles (TSP) in the atmosphere and gross alpha, gross beta as well as ⁹⁰Sr activities in both the atmosphere and drinking water. These variations were most likely produced by local re-suspension of soil material. However, ²¹⁰Pb and ⁷Be activities, measured in atmospheric aerosols, did not increase until a week after the storm had passed. ⁴⁰K and ¹³⁷Cs activities, also measured in atmospheric aerosols, did not vary significantly with respect to previous weeks indicating that the slightly higher levels of TSP, measured during the week when the storm occurred, were not produced by the long-range transport of re-suspended aerosols from the African continent, as it has been observed in other occasions at this site. Gross alpha, gross beta, ⁴⁰K and ⁹⁰Sr levels in drinking water samples increased after the storm over their average values by approximately 245%, 245%, 130% and 440%, respectively. These results indicate how important the local re-suspension and later deposition/scavenging of aerosols may be on the water supply in Tenerife.     

Classification of multiple types of organic carbon composition in atmospheric particles by scanning transmission X-ray microscopy analysis

A scanning transmission X-ray microscope at the Lawrence Berkeley National Laboratory is used to measure organic functional group abundance and morphology of atmospheric aerosols. We present a summary of spectra, sizes, and shapes observed in 595 particles that were collected and analyzed between 2000 and 2006. These particles ranged between 0.1 and 12 μm and represent aerosols found in a large range of geographical areas, altitudes, and times. They include samples from seven different field campaigns: PELTI, ACE-ASIA, DYCOMS II, Princeton, MILAGRO (urban), MILAGRO (C-130), and INTEX-B. At least 14 different classes of organic particles show different types of spectroscopic signatures. Different particle types are found within the same region while the same particle types are also found in different geographical domains. Particles chemically resembling black carbon, humic-like aerosols, pine ultisol, and secondary or processed aerosol have been identified from functional group abundance and comparison of spectra with those published in the literature.     

Low Flow Rate Sharp Cut Impactors for Indoor Air Sampling: Design and Calibration

Two single round nozzle impactors have been developed for use in Harvard’s indoor air pollution health study. Both impactors operate at flow rates of 4 L/m and are nearly identical, differing only in their cut sizes of 2.5 μm and 10 μm aerodynamic diameters. Two identical cascaded stages of the same cut size are used to obtain sharp cut-off characteristics. The particles are deposited on impaction plates made of oil impregnated, porous material to reduce particle bounce and are discarded. Only the particles collected on the afterfilter are analyzed. Special care has been taken to collect the particles uniformly on the afterfilter to aid in particle analysis.

The jmpactors were calibrated with a vibrating orifice monodisperse aerosol generator. However, due to the sharp cut of the impactors, doublets and triplets in the calibration aerosols, even in small quantities, gave erroneous calibration curves. Therefore, the number of doublets and triplets in the challenging aerosols were measured and appropriate corrections made to the calibration curves.     

The Mass Distribution of Large Atmospheric Particles

This paper describes the results of a study to determine the total mass and the mass distribution of atmospheric aerosols, especially that mass associated with particles greater than 10 μm diameter. This study also determined what fraction of the total aerosol mass a standard high-volume air sampler collects and what fraction and size interval settle out on a dust fall plate. A special aerosol sampling system was designed for this study to obtain representative samples of large airborne particles. A suburban sampling site was selected because no local point sources of aerosols existed nearby. Samples were collected under various conditions of wind velocity and direction to obtain measurements on different types of aerosols.

Study measurements show that atmospheric particulate matter has a bimodal mass distribution. Mass associated with large particles mainly ranged from 5 to 100 μm in size, while mass associated with small particles ranged from an estimated 0.03 to 5 μm in size. Combined, these two distributions produced a bimodal mass distribution with a minimum around 5 μm diameter. The high-volume air sampler was found to collect most of the total aerosol mass, not just that fraction normally considered suspended particulate. Dust fall plates did not provide a good or very useful measure of total aerosol mass. The two fundamental processes of aerosol formation, condensation and dispersion appear to account for the formation of a bimodal mass distribution in both natural and anthropogenic aerosols. Particle size distribution measurements frequently are in error because representative samples of large airborne particles are not obtained. Considering this descrepancy, air pollution regulations should specify or be based upon an upper particle size limit.     

The effect of temperature on the gas–particle partitioning of reactive mercury in atmospheric aerosols

Measurements of gas–particle-partitioning coefficients for reactive mercury in dry urban and laboratory aerosol were found to strongly depend on ambient temperature. Samples of atmospheric and laboratory aerosols (defined as both the gas and particle phases) were collected using filter and absorbent methods and analyzed for reactive mercury using thermal desorption combined with cold vapor atomic fluorescence spectroscopy. Synthetic ambient aerosols were generated in the laboratory from ammonium sulfate and adipic acid mixed with mercuric chloride in a purpose-built aerosol reactor. The aerosol reactor was operated in a temperature-controlled laboratory. Linear relationships between the logarithm of inverse gas–particle partitioning and inverse temperature were observed and parameterized for use in the atmospheric modeling of reactive mercury. Reactive mercury was observed to partition from the particle to the gas phase as ambient temperature increased. Good agreement between measurements made using urban and laboratory aerosols was seen after gas–particle-partitioning coefficients were normalized for surface area instead of mass. Thermodynamic analyses of the urban and laboratory gas–particle-partitioning measurements revealed that the strength of interaction between reactive mercury and particle surfaces was suggestive of chemisorption. Gas–particle-partitioning coefficients made with the Tekran ambient mercury analyzer (AMA) also showed a dependence on temperature. However, the Tekran AMA partitioning coefficients did not agree well with partitioning coefficients measured using the filter-based methods. The disagreement is consistent with the 50 °C operational temperature of the Tekran AMA.     

A new approach for the fractionation of water-soluble organic carbon in atmospheric aerosols and cloud drops

A novel approach is described for the fractionation of water-soluble organic carbon (WSOC) in atmospheric aerosols and cloud drops. The method is based on the preliminary adsorption of the sample, acidified at pH 2, on a polymeric styrene-divinylbenzene resin (XAD-2) and subsequent elution with a series of solvents, which leads to the fractionation of the sample into three classes of compounds. The method was set up using synthetic mixtures of organic compounds and then applied to selected samples of atmospheric aerosols and cloud drops. All samples and collected fractions were analysed using size exclusion chromatography (SEC). This method proved particularly useful both in providing information on the organic content of the samples and for the characterisation of the macromolecular compounds (MMCs) in the samples. Synthetic samples were prepared using humic, fulvic and tannic acid to simulate naturally occurring MMCs. In the first fraction, eluted with HCl, only the most soluble organic compounds (oxalic acid, formic acid and acetic acid) were collected. In the second fraction, eluted with methanol, the major part of the organic material was collected together with the more hydrophilic constituents of the humic substances. In the third fraction, it was possible to separately recover the more hydrophobic component of the humic substances. A large number of atmospheric samples (fog, aerosol, cloud) were then analysed using SEC. Most of these samples evidenced a noteworthy chromatogram at 254 nm. Moreover, the chromatographic area evidenced a clear linear correlation with the total organic carbon (TOC) values. The fractionation method on XAD-2 was finally applied to selected atmospheric samples, yielding three classes of organic compounds. In each sample, a non-negligible amount of compounds with dimensional and chemical properties similar to humic substances were collected in the third fraction. The carbon content in this latter fraction was estimated both by TOC and by means of the correlation between TOC and SEC area.     

Physicochemical and toxicological characteristics of urban aerosols during a recent Indonesian biomass burning episode

Air particulate matter (PM) samples were collected in Singapore from 21 to 29 October 2010. During this time period, a severe regional smoke haze episode lasted for a few days (21–23 October). Physicochemical and toxicological characteristics of both haze and non-haze aerosols were evaluated. The average mass concentration of PM_2.5 (PM with aerodynamic diameter of ≤2.5 μm) increased by a factor of 4 during the smoke haze period (107.2 μg/m³) as compared to that during the non-smoke haze period (27.0 μg/m³). The PM_2.5 samples were analyzed for 16 priority polycyclic aromatic hydrocarbons (PAHs) listed by the United States Environmental Protection Agency and 10 transition metals. Out of the seven PAHs known as potential or suspected carcinogens, five were found in significantly higher levels in smoke haze aerosols as compared to those in the background air. Metal concentrations were also found to be higher in haze aerosols. Additionally, the toxicological profile of the PM_2.5 samples was evaluated using a human epithelial lung cell line (A549). Cell viability and death counts were measured after a direct exposure of PM_2.5 samples to A459 cells for a period of 48 h. The percentage of metabolically active cells decreased significantly following a direct exposure to PM samples collected during the haze period. To provide further insights into the toxicological characteristics of the aerosol particles, glutathione levels, as an indirect measure of oxidative stress and caspase-3/7 levels as a measure of apoptotic death, were also evaluated.     

Hygroscopic organic aerosols during BRAVO?

The hygroscopic properties of the organic fraction of aerosols are poorly understood. The ability of organic aerosols to absorb water as a function of relative humidity (RH) was examined using data collected during the 1999 Big Bend Regional Aerosol and Visibility Observational Study (BRAVO). (On average, organics accounted for 22% of fine particulate matter with an aerodynamic diameter less than 2.5 microm (PM2.5) mass). Hourly RH exceeded 80% only 3.5% of the time and averaged 44%. BRAVO aerosol chemical composition and dry particle size distributions were used to estimate PM2.5 light scattering (Bsp) at low and high ambient RH. Liquid water growth associated with inorganic species was sufficient to account for measured Bsp for RH between 70 and 95%.     

Source apportionment of urban fine and ultra-fine particle number concentration in a Western Mediterranean city

Extensive measurements on particle number concentration and size distribution (13–800 nm), together with detailed chemical composition of PM_2.5 have constituted the main inputs of the database used for a source apportionment analysis. Data were collected at an urban background site in Barcelona, Western Mediterranean.The source identification analysis helped us to distinguish five emission sources (vehicle exhausts, mineral dust, sea spray, industrial source and fuel-oil combustion) and two atmospheric processes (photochemical induced nucleation and regional/urban background particles derived from coagulation and condensation processes). After that, a multilinear regression analysis was applied in order to quantify the contribution of each factor.This study reveals that vehicle exhausts contribute dominantly to the number concentration in all the particle sizes (52–86%), but especially in the range 30–200 nm. This work also points out the importance of the regional and/or urban formed aerosols (secondary inorganic particles) on the total number concentration (around 25% of the total number), with a higher impact on the accumulation mode. The photo-chemically induced nucleation of aerosols only represents a small proportion of the total number as an annual mean (3%), but is very relevant when considering only the nucleation mode (13–20 nm) fraction (23%). The other sources recognized registered sporadic contributions to the total number, coinciding with specific meteorological scenarios.This study discloses the main sources and features affecting and controlling the fine and ultra-fine aerosols in a typical city in the Western Mediterranean coast. Whereas the road traffic appears to be the most important source of sub-micrometric aerosols, other sources may not be negligible under specific meteorological conditions.     

Effects of Aerosol Species on Atmospheric Visibility in Kaohsiung City,Taiwan

Abstract

Visibility data collected from Kaohsiung City, Taiwan, for the past two decades indicated that the air pollutants have significantly degraded visibility in recent years. During our study period, the seasonal mean visibilities in spring, summer, fall, and winter were only 5.4, 9.1, 8.2, and 3.4 km, respectively. To ascertain how urban aerosols influence the visibility, we conducted concurrent visibility monitoring and aerosol sampling in 1999 to identify the principal causes of visibility impairments in the region. In this study, ambient aerosols were sampled and analyzed for 11 constituents, including water-soluble ions and carbon materials, to investigate the chemical composition of Kaohsiung aerosols. Stepwise regression method was used to correlate the impact of aerosol species on visibility impairments. Both seasonal and diurnal variation patterns were found from the monitoring of visibility. Our results showed that light scattering was attributed primarily to aerosols with sizes that range from 0.26 to 0.90 μm, corresponding with the wavelength region of visible light, which accounted for ～72% of the light scattering coefficient. Sulfate was a dominant component that affected both the light scattering coefficient and the visibility in the region. On average, (NH₄)₂SO₄, NH₄NO₃, total carbon, and fine particulate matter (PM_2.5)-remainder contributed 53%, 17%, 16%, and 14% to total light scattering, respectively. An empirical regression model of visibility based on sulfate, elemental carbon, and humidity was developed, and the comparison indicated that visibility in an urban area could be properly simulated by the equation derived herein.     

Iron isotopic fractionation in industrial emissions and urban aerosols

A study on tropospheric aerosols involving Fe particles with an industrial origin is tackled here. Aerosols were collected at the largest exhausts of a major European steel metallurgy plant and around its near urban environment. A combination of bulk and individual particle analysis performed by SEM–EDX provides the chemical composition of Fe-bearing aerosols emitted within the factory process (hematite, magnetite and agglomerates of these oxides with sylvite (KCl), calcite (CaCO₃) and graphite carbon). Fe isotopic compositions of those emissions fall within the range (0.08‰ < δ⁵⁶Fe < +0.80‰) of enriched ores processed by the manufacturer (−0.16‰ < δ⁵⁶Fe < +1.19‰). No significant evolution of Fe fractionation during steelworks processes is observed. At the industrial source, Fe is mainly present as oxide particles, to some extent in 3–4 μm aggregates. In the close urban area, 5 km away from the steel plant, individual particle analysis of collected aerosols presents, in addition to the industrial particle type, aluminosilicates and related natural particles (gypsum, quartz, calcite and reacted sea salt). The Fe isotopic composition (δ⁵⁶Fe = 0.14 ± 0.11‰) measured in the close urban environment of the steel metallurgy plant appears coherent with an external mixing of industrial and continental Fe-containing tropospheric aerosols, as evidenced by individual particle chemical analysis. Our isotopic data provide a first estimation of an anthropogenic source term as part of the study of photochemically promoted dissolution processes and related Fe fractionations in tropospheric aerosols.