Measurements of dissolved methylmercury in natural waters using diffusive gradients in thin film (DGT)

A diffusive gradient in thin films (DGT) technique for measuring methylmercury (MeHg) concentrations in natural waters was developed using 3-mercaptopropyl-functionalized silica gel to preconcentrate the methylmercury. The new resin was characterized and calibrated. Methylmercury is efficiently accumulated at a pH range of 3-9. Basic performance tests of the new DGT device confirmed the applicability of Fick's first law for such DGT measurements. The diffusion coefficient of methylmercury in polyacrylamide gel was 5 x 10(-6) cm(2) s(-1). Methylmercury concentrations determined by DGT deployed for different time periods in the field are statistically not different from results obtained through direct measurements. The DGT technique represents therefore an alternative in situ sampling method for methylmercury. The detection limit of the overall method is 1 pg of MeHg, which correspond to approximately 30 pg L(-1) of MeHg in a water sample, when deploying a typical DGT device for 24 hours. Lower MeHg concentrations are measurable using longer deployment times or thinner diffusive gel layers.     

Bioavailability assessment of phosphorus and metals in soils and sediments: a review of diffusive gradients in thin films (DGT)

This paper provides an overview of the principle and latest development of the diffusive gradients in thin films (DGT) technology and its applications in environmental studies with a focus on bioavailability assessment of phosphorus and metals in sediments and soils. Compared with conventional methods, DGT, as a passive sampling method, has significant advantages: in situ measurement, time averaged concentrations and high spatial resolution. The in situ measurement avoids artificial influences including contamination of samples and sample treatment which may change the forms of chemicals. The time averaged concentration reflects representative measurement over a period of time. The high-resolution information captures the biogeochemical heterogeneity of elements of interest distributed in microenvironments, such as in the rhizosphere and the vicinity of the sediment-water interface. Moreover, DGT is a dynamic technique which simultaneously considers the diffusion of solutes and their kinetic resupply from the solid phases. All the advantages of DGT significantly promote the collection of “true” information of the bioavailable or labile forms of chemicals in the environment. DGT provides potential for applications in agriculture, environmental monitoring and the mining industry. However, the applications are still at the early testing stage. Further studies are needed to properly interpret the DGT-measured results under complex environmental conditions, and standard procedures and guideline values based on DGT are required to pave the way for its routine applications in environmental monitoring.     

Application of DET (diffusive equilibrium in thin films) and DGT (diffusive gradients in thin films) techniques in the study of the mobility of sediment-bound metals in the outer section of Songkhla Lake, Southern Thailand

The techniques of diffusive equilibrium in thin films (DET) and diffusive gradients in thin films (DGT) were used in the outer section of Songkhla Lake, Thailand in order to obtain high-resolution profiles of total dissolved and labile trace metals in the sediment pore water and investigate benthic fluxes. Six DET probes and six DGT probes were deployed at the mouths of the Phawong, Samrong and U-Taphao canals. A close correspondence could be observed between the high-resolution profiles of Fe and As, revealing a close link between the reductive remobilization of Fe oxides and the reduction of As(V). Co and Ni DGT profiles showed a close correspondence with Mn, but a narrow mobilization zone. Reductive mobilization of Mn oxides and associated metals and sulfide precipitation control the behaviour of these metals. The DGT profiles of Cu, Zn, Cd and Pb show surface maximum, probably linked to organic matter degradation. Important benthic fluxes, especially for As, were found at the mouths of the U-Taphao and Phawong canals.     

Determination of Cu, Pb, Zn, Ni, Co, Cd, and Mn in road dusts of Samsun City

The dust samples from 52 different locations in central roads of Samsun City were collected in a study area of 40 km long for the purpose of determining total metal concentrations of dust samples by flame atomic absorption spectrometry. The concentrations of Cu, Pb, Co, Zn, Ni, Mn, and Cd were found in the ranges of 11.92–352.43, 5.47–223.57, 4.52–41.69, 40.85–173.10, 18.71–131.29, 133.19–179.13, and 0.02–6.16 mg/kg, respectively. The results showed that metal levels were higher around the industrial area than other locations. Principal component analysis was also carried out to ascertain the possible contributing factors towards the metal concentrations. Validation of the analytical results was tested by analysis of the BCR 032 Moroccan phosphate rock certified reference material.     

Trace metal speciation during dry and wet weather flows in the Tama River, Japan, by using diffusive gradients in thin films (DGT)

The labile species of Ni, Cu, Zn, Cd, and Pb in the Tama River, an urban river in Tokyo, Japan, were measured using diffusive gradients in thin films (DGT) method under dry and wet weather conditions, and the results were compared with total dissolved concentrations in hourly samples collected in parallel. A total of 10 DGT deployments were made and 251 hourly samples were collected during 2 rounds of sampling, conducted between August and October, 2006. Two types of diffusive gradients in thin films (DGT) devices-DGT-RG for labile inorganic and DGT-APA for total (inorganic and organic) labile species-were applied throughout the samplings. The proportions of metals measured by DGT, compared with the dissolved metal concentrations (filtered using a membrane of 0.5 microm pore size), were 38 +/- 5% (RG) and 45 +/- 8% (APA) for Ni and 45 +/- 22% (RG) and 53 +/- 23% (APA) for Zn. No labile Cu was detected throughout the sampling; Cu was assumed to be in stable complexed forms. Labile Pb was detected in 3 out of 10 deployments only; the rest were lower than the detection limit. Dissolved and labile Cd concentrations were below the detection limits. Three rain events encountered during the sampling periods were evaluated. Rains brought considerably higher loads of metals in dissolved form, and DGT measurements indicated that labile metal loads also increased. Selected DGT measurements were compared with the WHAM 6 speciation model and found to be similar to the model-computed results.     

Competitive sorption of Cd, Cu, Mn, Ni, Pb and Zn in polluted and unpolluted calcareous soils

The objectives of this study were to investigate competitive sorption behaviour of heavy metals (Cd, Cu, Mn, Ni, Pb and Zn) under different management practices and identify soil characteristics that can be correlated with the retention and mobility of heavy metals using 65 calcareous soil samples. The lowest sorption was found for Mn and Ni in competition with the other metals, indicating the high mobility of these two cations. The Freundlich equation adequately described heavy metals adsorption. On the basis of Freundlich distribution coefficient, the selectivity sequence of the metal adsorption was Cu?>?Pb?>?Cd?>?Zn?>?Ni?>?Mn. The mean value of the joint distribution coefficient (K _dΣsp) was 182.1, 364.1, 414.7, 250.1, 277.7, 459.9 and 344.8 l kg^?1 for garden, garlic, pasture, potato, vegetables, wheat and polluted soils, respectively. The lowest observed K _dΣsp in garden soil samples was due to the lower cation exchange capacity and lower carbonate content. The results of the geochemical modelling under low and high metal addition indicated that Cd, Ni, Mn and Zn were mainly retained via adsorption, while Pb and Cu were retained via adsorption and precipitation. Stepwise forward regression analysis showed that clay, organic matter and CaCO₃ were the most important soil properties influencing competitive adsorption of Cd, Mn, Ni and Zn. The results in this study point to a relatively easy way to estimate distribution coefficient values.     

Bioavailability of copper,cadmium, zinc,and lead in tropical savanna soils assessed by diffusive gradient in thin films (DGT) and ion exchange resin membranes

The technique of diffusion gradient in thin films (DGT) for assessing bioavailable metals has not been tested under field conditions. We assessed the relationships of DGT- and cation exchange resin-membrane-measured concentrations of Cd, Cu, Pb, and Zn with plant uptake of the metals under greenhouse and field conditions. In the greenhouse, the effective concentrations of Cu, Pb, and Zn by DGT correlated significantly with uptake by sorghum (Sorghum bicolor), but cation exchange resin-membrane-measured concentrations of Cd, Pb, and Zn did not correlate with sorghum uptake. In the field, the DGT-measured concentrations of Cd, Pb, and Zn were not linearly related to uptake Cd, Pb, and Zn by lettuce (Lactuca sativa) except for Cu uptake (r = 0.87, p < 0.05). Similarly, it was only the resin-membrane-extractable Pb that correlated with Pb uptake by lettuce (r = 0.77; p < 0.05). However, fitting non-linear regression models improved the plant metal uptake predictions by DGT-measured bioavailable Cd, Cu, Pb, and Zn under field conditions. In conclusion, the DGT technique was fairly predictive of bioavailability in the greenhouse, but not in the field.     

Evaluation of Pb, Cu, Zn, Cd, Ni and Fe levels in Rosmarinus officinalis labaiatae (Rosemary) medicinal plant and soils in selected zones in Jordan

The concentration of heavy metals including Pb, Cu, Zn, Cd, Ni and Fe in different parts of Rosmarinus officinalis medicinal plant grown in Jordan were evaluated. Medicinal plant samples and soil samples were collected from three different zones in Jordan (Irbid, Al-Mafraq and Ma’an). Samples were analyzed by atomic absorption spectrometry (AAS) after chemical treatments using acid digestion procedures. Heavy metal levels in washed and unwashed in each part of R. officinalis were analyzed and compared statistically. Results show that concentrations of investigated heavy metals were varied from plant part to another part of R. officinalis. For example, Pb, Zn, Cu and Cd in most parts of R. officinalis in the three zones were concentrated in the following order: flowers, leaves, stems, whereas Pb, Ni and Fe were concentrated in order as follows: leaves, flowers and stems. Heavy metal concentrations in soil samples was evaluated and correlated with their levels in R. officinalis. Two standard reference materials of plant (SRM 1790a; spinach leaves and CRM 281; rye grass) and one standard reference materials of soil (GBW 07406) were examined to validate the method used. Results show that high recoveries were obtained.     

Monitoring of (bio)available labile metal fraction in a drinking water treatment plant by diffusive gradients in thin films

A performance study of diffusive gradients in thin films (DGT) and inductively coupled plasma optical emission spectrometry (ICP-OES) was applied for the monitoring of the labile fraction of metals Al, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn, in Sant Joan Despí Drinking Water Treatment Plant located in the South of Barcelona’s Metropolitan Area (Spain). The DWTP monitoring protocol was optimized by working for 1 day of deployment (24 h) with the DGT device in contact with both treated and river water matrixes. Additionally, it was demonstrated that an increase in the deployment time of 1 week did not decrease the evaluated concentrations of the studied metals. The quality parameters of the DGT device and ICP-OES determination, such as limit of quantification, accuracy expressed as relative error (%) and reproducibility expressed as relative standard deviation, were evaluated. Good results were obtained for all the metals in ultrapure water; limits of quantification ranged from 1.5 μg L^− 1 for cadmium to 28 μg L^− 1 for zinc when deployment time of 24 h was used and from 0.2 μg L^− 1 for cadmium to 4 μg L^− 1 for zinc when this time was increased by 1 week. Accuracy and precisions lower than or equal to 10% were obtained at a parametric concentration value of the metals regulated in the European Drinking Water Guidelines (98/83/EC). DGT deployment was tested in river and treated water, and good results were obtained for Cd, Ni, Co and Zn, whereas for the other metals, a continuous control of their metallic labile fractions was monitored. Therefore, DGT device allows the continuous monitoring of the labile metal species in a drinking water treatment plant.     

Comparison of diffusive gradients in thin film technique with traditional methods for evaluation of zinc bioavailability in soils

The technique of diffusive gradients in thin film (DGT) has been shown to be a promising tool to assess zinc (Zn) bioavailability in soils, but there exists considerable debate on its suitability. In this study, Zn bioavailability was systematically investigated in wheat- and maize-grown soils using this technique and seven traditional methods, including soil solution concentration and six widely used single-step extraction methods (HAc, EDTA, NaAc, NH₄Ac, CaCl₂, and MgCl₂). The concentrations of Zn in the shoots and roots of these two plant species increased continuously with increasing additions of Zn to the soils, accompanied by significant decreases in shoot biomass and root biomass at Zn concentrations greater than 400 mg kg^?1 for maize and 800 mg kg^?1 for wheat. Zinc uptake and accumulation was higher in maize roots than in wheat roots. Both the concentrations of bioavailable Zn measured by DGT (C _DGT) and soil solutions (C _sol) increased linearly with increasing additions of Zn to the soils, while no strong linear relationships were observed for the extraction methods. Higher concentrations of extractable Zn, lower values of C _sol, and larger values of R (i.e., the ratio of C _DGT to C _sol) were observed in maize-grown soils compared with those of wheat-grown soils, while the values of C _DGT between the two plants were similar. These findings demonstrate that there likely exists a stronger resupply of Zn from the soil solid phases in maize-grown soils to satisfy a higher Zn uptake and accumulation in this plant. Linear correlation analyses showed that C _DGT had the highest correlation coefficients with plant Zn concentrations compared with other traditional methods, implying that the DGT technique is more sensitive and robust in reflecting Zn bioavailability in soils to plants.     

Chemical speciation and partitioning of trace metals (Cd, Co, Cu, Ni, Pb) in the lower Athabasca river and its tributaries (Alberta, Canada)

Concentrations of Cd, Co, Cu, Ni and Pb were measured in particulate and dissolved phases at 11 sites located upstream and near Athabasca oil sands development. The in situ discrimination between non-labile and labile dissolved metals was done using diffusive gradients in thin-films (DGT) devices. The DGT-labile fraction of Co and Ni was 30% lower near development sites whereas Cu, Cd and Pb showed minor changes spatially. It was found that an 8-fold increase in dissolved organic matter (DOM) near development induced a rapid decrease in DGT-labile metals. Dissolved metal concentrations were used along with DOM, major ions, nutrients, pH and conductivity to calculate the distribution of dissolved metal species using the speciation model WHAM. Labile-DGT metal concentrations agreed well with WHAM-predicted concentrations. It was also found that a significant amount of metals were associated with the non-DGT labile fraction (i.e. colloidal DOM) and colloid abundance was more important than suspended particulate matter abundance in influencing metal mobility near Athabasca oil soils development. Since changes in colloidal DOM levels are likely to be the result of surface mining activities, this confirms the serious effects of oil sands activities on metal biogeochemical cycles in the lower Athabasca River.     

Concentration of Cd, Cu, Pb, Zn, Al, and Fe in soils of Manresa, NE Spain

The aims of this study were to determine the contents of cadmium (Cd), copper (Cu), lead (Pb), zinc (Zn), aluminium (Al), and iron (Fe) (aqua regia-extractable) in 27 soil plots (54 samples) from Manresa, NE Spain, and to establish relationships between heavy metals and some soil properties. The main soil types were surveyed and the median concentrations (mg kg(-1)) obtained were Cd 0.28, Cu 20.3, Pb 18.6, Zn 67.4, Al 22,572, and Fe 21,551. Element concentrations for these soils were lower than the published values for the Valencia region (Spain) and Torrelles and Sant Climent municipal districts (Catalonia, Spain). In terms of soil properties, the results of this study suggest that, in Manresa soils, both trace element adsorption and retention are influenced by several properties such as clay minerals, carbonates, organic matter, and pH. All element contents were positively correlated with clay content. Pb and Zn were negatively correlated with pH and CaCO(3).     

Atmospheric deposition of heavy metals (Cu, Zn, Cd and Pb) in Varanasi City, India

Rapid growth in urbanization and industrialization in developing countries may significantly contribute in heavy metal contamination of vegetables through atmospheric depositions. In the present study, an assessment was made to investigate the spatial and seasonal variations in deposition rates of heavy metals and its contribution to contamination of palak (Beta vulgaris). Samples of bulk atmospheric deposits and Beta vulgaris for analysis of Cu, Zn, Cd and Pb were collected from different sampling locations differing in traffic density and land use patterns. The results showed that the sampling locations situated in industrial or commercial areas with heavy traffic load showed significantly elevated levels of Cu, Zn and Cd deposition rate as compared to those situated in residential areas with low traffic load. The deposition rates of Cu, Zn and Cd were significantly higher in summer and winter as compared to rainy season, however, Pb deposition rate was significantly higher in rainy and summer seasons as compared to winter season. Atmospheric depositions have significantly elevated the levels of heavy metals in B. vulgaris collected during evening as compared to those collected in morning hours. The study further showed that local population has maximum exposure to Cd contamination through consumption of B. vulgaris. The present study clearly points out the urban and industrial activities of a city have potential to elevate the levels of heavy metals in the atmospheric deposits, which may consequently contaminate the food chain and thus posing health risk to the local population.     

Solid phase extraction of Cd,Pb, Ni,Cu, and Zn in environmental samples on multiwalled carbon nanotubes

A simple and sensitive solid phase extraction (SPE) method on multiwalled carbon nanotubes (MWCNTs) is presented for the determination of cadmium, lead, nickel, copper, and zinc at trace levels combined with flame atomic absorption spectrometry. The effects of parameters like pH, sample volume, sample and eluent flow rates, eluent concentration, and volume and type of eluent on the recovery of trace elements was examined. The metals retained on the nanotube at pH 6.5 as α-benzoin oxime complexes were eluted by 10 mL 2 M HNO₃ in acetone. The influence of matrix ions on the developed method was also evaluated. The preconcentration factor of the method was found to be 50. The detection limits for Cd(II), Pb(II), Ni(II), Cu(II), and Zn(II) were found as 1.7, 5.5, 6.0, 2.3, and 2.4 μg L^?1, respectively. To test the accuracy of the method, the method was applied to TMDA-70 fortified lake water and Spinach 1570A standard reference materials. Addition recovery studies were applied to tap water and cracked wheat samples, and determination of the analyte elements was carried out in some food samples with good results.     

Environmentally safe sewage sludge disposal: the impact of liming on the behaviour of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn

Dewatered sewage sludge containing relatively high total concentrations of Cr (945 micrograms ml-1), Cu (523 micrograms ml-1), Ni (1186 micrograms ml-1) and Zn (2950 micrograms ml-1) was treated with quicklime and sawdust for sludge disinfection and post-stabilisation. The mobility of the heavy metals in the sludge samples was assessed by applying a modified five-step Tessier sequential extraction procedure. Water was added as a first step for estimation of the proportion of the easily soluble metal fractions. To check the precision of the analytical work the concentrations of heavy metals in steps 1-6 of the extraction procedure were summed and compared to the total metal concentrations. The mass balance agreed within +/- 3% for Cd, Cu, Cr, and Zn and within +/- 5% for Ni, Pb, Fe and Mn. Data from the partitioning study indicate that in the lime-treated sludge at a pH of 12 the mobility of Cu and Ni notably increased with the solubilisation of these metals from their organic and/or carbonate and Fe and Mn oxide and hydroxide fractions, respectively. Liming slightly decreased the proportion of other heavy metals in the easily soluble fractions while its impact on the partitioning between other sludge phases was almost insignificant. Due to the increased solubility of Ni and Cu as well as potential Cr oxidation at high pH, liming cannot be recommended for sludge disinfection. Addition of sawdust did not change the heavy metal partitioning.     

Spatial distribution of trace metals (Cd, Pb, Hg, Cu, Zn, Fe and Mn) and oligo-elements (Mg, Ca, Na and K) in surface sediments of the Gulf of Tunis (Northern Tunisia)

The purpose of this paper is to evaluate the levels and spatial distribution of trace metals (Cd, Pb, Cu, Hg, Zn, Fe, and Mn), oligo-elements (Mg, Ca, Na and K), total organic carbon (TOC), and total nitrogen (TN) in the fine fraction of surface sediments collected from 38 stations in Gulf of Tunis (Mediterranean Sea, Northern Tunisia) between 2004 and 2005. The results showed that metals, oligo-elements, TOC, and TN concentrations in the sediments of the Gulf of Tunis are generally low compared to those found in other similar coastal marine areas. The spatial distribution of metals showed areas of major accumulation of Pb, Cd, Cu, Fe, and Zn in the central area of the Gulf and near the Mejerda River. The marine currents are influencing factors on metal accumulation in sediments. The principal component analysis applied to our elemental analytical results showed that there is a positive correlation between Fe, Zn, Cu, and Pb. These metals have a stronger affinity with site connection in the sediments than Ca and Mn.     

Determination of heavy metals (Cd, Cr, Cu, Fe, Ni, Pb, Zn) by ICP-OES and their speciation in Algerian Mediterranean Sea sediments after a five-stage sequential extraction procedure

Surface sediment samples (n = 18) were collected from the Algerian Mediterranean coasts and analyzed for seven metals using inductively coupled plasma-optical emission spectrometry in order to asses the distribution and bioavailability of metals and to study the anthropogenic factors affecting their concentrations. Sediment samples were size-fractionated into three sizes: 1,080–500 (coarse), 500–250 (medium), and <250 mm (fine). Bulk sediments were subjected to both sequential extraction and total digestion to evaluate the reliability of the sequential extraction procedure (SEP), while the fractions have been only sequentially extracted for metals speciation. The metals were sequentially extracted into five phases namely exchangeable (P1), carbonates (P2), Fe–Mn oxides (P3), organic (P4) and residual (P5). Metal recoveries in sequential extractions were ±20% of the independently measured total metal concentrations; the high recovery rates indicate the good reliability of the SEP used in this study. Correlation coefficients indicated that the grain size has an effect on the distribution of metals in the investigated samples. The order of metal levels in the fractions was medium > fine > coarse for all the metals. The average total extractable metal concentrations for Cd, Cr, Cu, Fe, Ni, Pb, and Zn were 1.1, 8.8, 4.7, 1,291.3, 13.9, 5.7 and 20.4 μg/g, respectively. The northeastern shelf had the lowest metal levels while the highest were in northwestern part mainly due to the significant tourism activities in the northwestern part. Comparison of our results to Earth’s crust values and to previous studies points out that our samples were relatively unpolluted with respect to the heavy metals investigated; most of the metals are not from anthropogenic sources. Enrichment factors as the criteria for examining the impact of the anthropogenic sources of heavy metals were calculated, and it was observed that the investigated samples were not contaminated with Cr, Cu, and Fe, moderately contaminated with Ni, Pb, and Cd, and contaminated with Cd in some sites. The P5 phase had the highest percents of Cr, Cu, Fe, Ni, and Zn. Cadmium and lead were predominant in the P4 phase, while Cu, Fe and Zn were distributed in the order P5 > P3 > P4 > P2 > P1. The following order of bioavailability was found with the heavy metals Pb > Cr > Cd > Ni > Zn > Cu > Fe.     

Distribution of metals (Fe, Mn, Zn, Cu) in fish tissues in two lakes of different trophy in Northwestern Poland

This study presents concentrations of iron, manganese, zinc, and copper in selected tissues of two fish species: pike (Esox lucius L.) and bream (Abramis brama L.) living in lakes Ińsko and Wisola, Northwestern Poland. The lakes differ in their trophic status. The effect of gender and environmental conditions on metals accumulation was also investigated. Metal analyses were performed using inductively coupled plasma atomic emission spectroscopy. Considering all studied fish species and tissues, the average metal concentrations (micrograms per gram wet weight) in both lakes occurred in the following ranges: Fe 0.8–240.6, Mn 0.2–8.4, Zn 3.0–185.9, and Cu 0.14–7.76. The lowest levels of the studied metals were always detected in the muscles. The spleen, kidneys, and liver were found to accumulate the highest amounts of Fe. In the case of the other metals, the highest levels were found, as follows: Mn in skin, gills, and gonads, Zn in digestive tract and gills, Cu in liver. Heavy metal content in fish gonads was observed to be sex dependent.     

Trace Level Determination of U, Zn, Cd, Pb and Cu in Drinking Water Samples

The concentration of uranium has been assessed in drinking water samples collected from different locations in Bathinda district, Punjab, India. The water samples are taken from hand pumps and tube wells. Uranium is determined using fission track technique. Uranium concentration in the water samples varies from 2.23± 0.05 to 87.05± 0.29 μg/L. These values are compared with safe limit values recommended for drinking water. The uranium concentration in almost all drinking water samples is found to be more than the safe limit. Analysis of some heavy metals viz. Zn, Cd, Pb and Cu in water is made. The concentration of sodium, potassium, calcium, magnesium, chlorine and total hardness along with the pH value and conductivity of the water samples are measured. Some of the samples show stunningly high values of these parameters.