Background culturable bacteria aerosol in two large public buildings using HVAC filters as long term, passive, high-volume air samplers

Background culturable bacteria aerosols were collected and identified in two large public buildings located in Minneapolis, Minnesota and Seattle, Washington over a period of 5 months and 3 months, respectively. The installed particulate air filters in the ventilation systems were used as the aerosol sampling devices at each location. Both pre and final filters were collected from four air handing units at each site to determine the influence of location within the building, time of year, geographical location and difference between indoor and outdoor air. Sections of each loaded filter were eluted with 10 ml of phosphate buffered saline (PBS). The resulting solutions were cultured on blood agar plates and incubated for 24 h at 36 degrees C. Various types of growth media were then used for subculturing, followed by categorization using a BioLog MicroStation (Biolog, Hayward, CA, USA) and manual observation. Environmental parameters were gathered near each filter by the embedded on-site environmental monitoring systems to determine the effect of temperature, humidity and air flow. Thirty nine different species of bacteria were identified, 17 found only in Minneapolis and 5 only in Seattle. The hardy spore-forming genus Bacillus was the most commonly identified and showed the highest concentrations. A significant decrease in the number of species and their concentration occurred in the Minneapolis air handling unit supplying 100% outdoor air in winter, however no significant correlations between bacteria concentration and environmental parameters were found.     

Development of a solid phase microextraction (SPME) method for the sampling of VOC traces in indoor air

Solid-phase microextraction (SPME) was studied for the measurement of volatile organic compounds (VOCs) in indoor air. An adsorptive PDMS/Carboxen fibre was used and an analytical methodology was developed in order to overcome competitive adsorption. Kinetics and adsorption isotherms were investigated for different sample volumes and model compounds. In order to evaluate competitive adsorption on the fibre, these compounds were studied alone and in mixture. From the results obtained, the operating conditions allowing co-adsorption of the target compounds were determined: the air sample is enclosed in a 250 mL glass bulb where the SPME fibre is exposed until adsorption equilibrium. This procedure was combined with GC/MS analysis for the identification and quantification of VOCs in indoor air. The performances were determined by using a standard gas containing 10 VOCs representative of indoor environments (acetaldehyde, acetone, BTX, alpha-pinene, trichloroethylene, alkanes). The detection limits were determined in single ion monitoring mode and for a signal to noise ratio of 3. Except acetaldehyde (6 microg m(-3)), they are all below 0.5 microg m(-3). Calibration curves are linear up to 10 micromol m(-3) for all the compounds with good correlation coefficients (above 0.99). The reproducibility ranges from 6 to 12% according to the compound. The methodology was then applied to the comparison of the VOCs content in classrooms of two different schools.     

Development of a diffusive sampling method for determination of methyl isocyanate in air

A diffusive sampling method for determination of methyl isocyanate in air has been developed. A glass fibre filter impregnated with 1-(2-methoxyphenyl)piperazine in a commercially available diffusive sampling device was used to collect methyl isocyanate and the derivative formed was analysed with LC-MS/MS. The sampling rate was determined to be 15.6 ml min(-1), with a relative standard deviation of 7.3%. The sampler was validated for sampling periods from 15 min to 8 h, for relative humidities from 20% to 80% and for concentrations from I to 46 microg m(-3). A field validation was also made and the diffusive sampling results showed no difference compared to a pumped reference method. The impregnated filters have to be stored apart from the diffusive sampler housing and loaded into the sampler prior to each sampling.     

Development of baseline (air quality) data in Pakistan

During 2003–2004, SUPARCO, the Pakistan Space and Upper Atmosphere Research Commission has conducted a year long baseline air quality study in country’s major urban areas (Karachi, Lahore, Quetta, Rawalpindi, Islamabad and Peshawar). The objective of this study was to establish baseline levels and behavior of airborne pollutants in urban centers with temporal and spatial parameters. This study reveals that the highest concentrations of CO were observed at Quetta (14 ppm) while other pollutants like SO₂ (52.5 ppb), NO _x (60.75 ppb) and O₃ (50 ppb) were higher at Lahore compared to other urban centers like Karachi, Peshawar etc. The maximum particulate (TSP) and PM10 levels were observed at Lahore (996 ug/m³ and 368 ug/m³ respectively), Quetta (778 ug/m³, 298 ug/m³) and in Karachi (410 ug/m³, 302 ug/m³). In all major cities the highest levels were recorded at major intersections and variations were directly correlated with traffic density. These pollutants showed highest levels in summer and spring while lowest were observed in winter and monsoon. A data bank has been generated for future planning and air pollution impact studies.     

A comparison of X-ray fluorescence and wet chemical analysis for lead on air filters from different personal samplers used in a bronze foundry

Portable X-ray fluorescence (XRF) technology may provide faster turn-around without compromising accuracy when assessing personal exposures to metals such as lead, but it has only been tested in limited field environments. This study is part of a series, where different sampler types are used to collect airborne lead in different environments for presentation to a portable XRF analyzer. In this case personal samples were taken at a bronze foundry where lead is added to an alloy of copper, zinc and iron to improve casting, using the closed-face 37 mm cassette, the 37 mm GSP or "cone" sampler, the 25 mm Institute of Occupational Medicine (IOM) inhalable sampler, the 25 mm Button sampler, and the open-face 25 mm cassette. Mixed cellulose-ester filters were used in all samplers. Following XRF analysis the samples were extracted with acid and analyzed by inductively coupled plasma optical emission spectroscopy (ICP). For lead, all five samplers gave correlations (r(2)) greater than 0.9 between the two analytical methods over the entire range of found lead mass, which encompassed both the action level and the permissible exposure limit enforced in the USA by the Occupational Safety and Health Administration (OSHA). However, a correction was required to adjust linear regression trendlines to give a 1 : 1 correlation for the average of three readings across the GSP sampler, and a similar correction was required for the single readings from the IOM sampler and the 25 mm filter cassette. The bias possibly is due to interference from other metals, possibly copper which can absorb the fluorescent radiation of lead. In the case of the Button sampler, the bias is larger, indicating a further source of error, perhaps due to the thickness of the deposit. However, in all cases, correction of the lead results did not greatly affect the overall percentage of samples where the XRF result was within 25% of the ICP result, although it did improve the overall accuracy of the results. The GSP, IOM and Button samplers are suitable candidates for further evaluation as compatible with on-site XRF analysis for lead and other metals. It is important to check carefully factory pre-set instrument calibrations, as a bias in the calibration for copper was observed.     

Preparation, certification and interlaboratory analysis of workplace air filters spiked with high-fired beryllium oxide

Occupational sampling and analysis for multiple elements is generally approached using various approved methods from authoritative government sources such as the National Institute for Occupational Safety and Health (NIOSH), the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA), as well as consensus standards bodies such as ASTM International. The constituents of a sample can exist as unidentified compounds requiring sample preparation to be chosen appropriately, as in the case of beryllium in the form of beryllium oxide (BeO). An interlaboratory study was performed to collect analytical data from volunteer laboratories to examine the effectiveness of methods currently in use for preparation and analysis of samples containing calcined BeO powder. NIST SRM(?) 1877 high-fired BeO powder (1100 to 1200 °C calcining temperature; count median primary particle diameter 0.12 μm) was used to spike air filter media as a representative form of beryllium particulate matter present in workplace sampling that is known to be resistant to dissolution. The BeO powder standard reference material was gravimetrically prepared in a suspension and deposited onto 37 mm mixed cellulose ester air filters at five different levels between 0.5 μg and 25 μg of Be (as BeO). Sample sets consisting of five BeO-spiked filters (in duplicate) and two blank filters, for a total of twelve unique air filter samples per set, were submitted as blind samples to each of 27 participating laboratories. Participants were instructed to follow their current process for sample preparation and utilize their normal analytical methods for processing samples containing substances of this nature. Laboratories using more than one sample preparation and analysis method were provided with more than one sample set. Results from 34 data sets ultimately received from the 27 volunteer laboratories were subjected to applicable statistical analyses. The observed performance data show that sample preparations using nitric acid alone, or combinations of nitric and hydrochloric acids, are not effective for complete extraction of Be from the SRM 1877 refractory BeO particulate matter spiked on air filters; but that effective recovery can be achieved by using sample preparation procedures utilizing either sulfuric or hydrofluoric acid, or by using methodologies involving ammonium bifluoride with heating. Laboratories responsible for quantitative determination of Be in workplace samples that may contain high-fired BeO should use quality assurance schemes that include BeO-spiked sampling media, rather than solely media spiked with soluble Be compounds, and should ensure that methods capable of quantitative digestion of Be from the actual material present are used.     

TEA(三乙醇胺)挂片测定空气中NO2的滤膜制备方法

介绍了一种用于TEA挂片测定NO2的滤膜制备方法,解决了原方法中存在的滤膜空白值偏高且不稳定的问题.实验结果表明,该方法可用于大面积、多点位同步监侧中大批量滤膜的制备.     

Development of a Pollination Service Measurement (PSM) method using potted plant phytometry

The value of pollination to human society is not limited to agricultural production, but also in the sustainability of ecosystems and the services that they provide. Seed set can be used as a comparative measure of pollination effectiveness, with minimum variability expected when other resources are not limiting. Six species of self-incompatible fall asters (Symphyotrichum) were used to evaluate pollination service at 12 sites across a spectrum of expected levels of pollination. Seed set per inflorescence was generally lower at sites with lower pollinator numbers and diversity, although as expected pollinator assemblage characteristics were highly variable within and between sites. However, rankings of sites showed consistency of response across phytometer species and between years; the summed ranks across multiple species appears to have as the greatest value in Pollination Service Measurement (PSM). Abundance, richness, and Shannon diversity of pollinator assemblages were highly autocorrelated and showed variable relationships with seed set depending on plant species and temporal scale of pollinator assemblage assessment. Use of seed set to directly measure pollination service at a site was consistent and cost effective when compared to less certain and more labour-intensive methods of pollinator collection and identification, and shows promise for implementation in pollination monitoring and bioassessment practices.     

水中粪大肠菌群快速检测方法-固定底物酶底物法与多管发酵法的比较

目的在于比较固定底物酶底物法与多管发酵法用于水中粪大肠菌群(耐热大肠菌群)的检测,使用科立得TM(Colilert(R))试刺和传统方法检测地表水、水源水及污水水样,比较固定底物酶底物法与多管发酵法用于水中粪大肠菌群(耐热大肠菌群)检测结果的一致性.结果表明,固定底物酶底物法与多管发酵法用于水中粪大肠菌群(耐热大肠菌群)检测结果具有一致性,固定底物酶底物法可以用作评价水质微生物污染的标准方法.     

A comparison of X-ray fluorescence and wet chemical analysis for lead on air filters from different personal samplers used in a secondary lead smelter/solder manufacturer

Portable X-ray fluorescence (XRF) technology may provide faster turn-around without compromising accuracy when assessing personal exposures to metals such as lead, but it has only been tested in limited field environments. This study is part of a series, where various types of sampler are used to collect airborne lead in different environments for presentation to a portable XRF analyzer. In this case personal samples were taken at a manufacturer of solder alloys consisting mainly of lead and tin, using the closed-face 37 mm cassette (CFC), the 37 mm GSP or "cone" sampler, the 25 mm Institute of Occupational Medicine (IOM) inhalable sampler, the 25 mm button sampler, and the open-face 25 mm cassette. Mixed cellulose-ester filters were used in all samplers. Following XRF analysis the samples were extracted with acid and analyzed by inductively coupled plasma optical emission spectroscopy (ICP). The internal surfaces of CFC's and 25 mm open-face cassettes were also wiped, and the wipes analyzed for lead to assess wall-losses in these two samplers. Analysis of all elements present is useful to ascertain contributions to matrix interference effects. In addition to lead, other metals such as tin, copper, iron, silver, cadmium and antimony were also detected in some or all of the samples by ICP analysis, but only copper and iron could be determined using the XRF analyzer under test. After the removal of a few outliers, all five samplers gave good correlations (r(2) > 0.9) between the two analytical methods over the entire range of found lead mass, which encompassed both the action level and the permissible exposure limit enforced in the USA by the Occupational Safety and Health Administration (OSHA). Linear regression on the results from most samplers gave almost 1 ratio 1 correlations without additional correction, indicating an absence of matrix effects, particularly from tin, which was the most common element after lead. The average of three XRF readings across filters from the GSP samplers gave the best results with 96.7% of results within +/-25% and 100% within +/-30% of the associated ICP values. Using the center reading only was almost as good with 90.0% of results within +/-25% and 96.7% within +/-30% of the associated ICP values, and results can be obtained faster with a single reading. The use of an algorithm developed by OSHA for three readings from the CFC filter samples gave the next best results with 93.3% of XRF results within +/-25% of the corresponding ICP values. However, analysis of wipes from the interior of the cassettes indicated a substantial loss of sample to the walls, and even larger wall-losses were encountered in the 25 mm open-face cassette. Neither this latter sampler nor the IOM or button sampler met the 95% criterion, even for +/-30% accuracy.     

Evaluation of a standardized method for determining soluble silver in workplace air samples

Several occupational exposure limits and guidelines exist for silver, but the values for each depend on the chemical form of the silver compound in question. In the past, it generally was not possible, without prior knowledge of the work process, to distinguish soluble silver from insoluble silver compounds collected in workplace air samples. Therefore, analytical results were historically reported as total silver. In this study, work was conducted to evaluate a method to differentiate between the quantities of water-soluble silver compounds and total silver collected on filters. The investigation entailed an evaluation of an International Organization for Standardization method to determine soluble silver in airborne particulate matter. The study design incorporated laboratory experiments to evaluate analytical figures of merit, such as selection of appropriate filter media and extraction solution, analytical recovery, and sample stability during storage. Polytetrafluoroethylene (PTFE) filters (2 microm, 37 mm) in opaque cassettes were either spiked with known amounts of silver nitrate or contained a known mass of solid silver nitrate. Results showed that over 90% of the silver was recovered from PTFE filters. Also, field studies were conducted in which workplace air samples were collected in two silver refineries. Some of these samples were analyzed only for soluble silver while others were sequentially extracted and analyzed, first, for soluble silver, then for total silver. The mass fractions of soluble silver, as compared to total silver, were approximately 2% or less. This investigation served to validate an international standard procedure for the determination of soluble silver in workplace air samples.     

Chromium (VI) biosorption properties of multiple resistant bacteria isolated from industrial sewerage

Chromium (VI) [Cr (VI)] biosorption by four resistant autochthonous bacterial strains was investigated to determine their potential for use in sustainable marine water-pollution control. Maximum exchange between Cr (VI) ions and protons on the cells surfaces were at 30–35 °C, pH?2.0 and 350–450 mg/L. The bacterial strains effectively removed 79.0–90.5 % Cr (VI) ions from solution. Furthermore, 85.3–93.0 % of Cr (VI) ions were regenerated from the biomasses, and 83.4–91.7 % of the metal was adsorbed when the biomasses was reused. Langmuir isotherm performed better than Freundlich isotherm, depicting that Cr (VI) affinity was in the sequence Rhodococcus sp. AL03Ni?>?Burkholderia cepacia AL96Co?>?Corynebacterium kutscheri FL108Hg?>?Pseudomonas aeruginosa CA207Ni. Biosorption isotherms confirmed that Rhodococcus sp. AL03Ni was a better biosorbent with a maximum uptake of 107.46 mg of Cr (VI) per g (dry weight) of biomass. The results highlight the high potential of the organisms for bacteria-based detoxification of Cr (VI) via biosorption.     

Evaluation of a simultaneous sampling method of PAHs, PCDD/Fs and dl-PCBs in ambient air

The Stockholm Convention on Persistent Organic Pollutants (POPs) was signed in May 2001 by 127 countries. Currently, 12 substances are regulated by the convention, and the work on finding new candidate chemicals to the convention has started. Among these 12 substances, dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polychlorinated biphenyls (PCBs) are the objects of this study. There are no European standard methods for the simultaneous determination of these microorganic compounds, together with polycyclic aromatic hydrocarbons (PAHs) in ambient air--they must be referred to three different methods developed by the U.S. Environmental Protection Agency (EPA). The quali-quantitative analysis of these microorganic pollutants is an important challenge due to the low concentrations at which they may be present. In this study, the development of a simplified, alternative, fast and affordable sampling method for the determination of PAHs, PCDDs, PCDFs and PCBs in ambient air was performed. The sampling time was extended from 24 h to 7 d in order to enrich the sample, to fall within the instrumental limits of detection and to reduce the number of samples to be processed and, therefore, errors that may arise. First of all, experiments with labelled standards were conducted in the research area of Montelibretti (rural station, which is sited about 20 km northeast of Rome), with the purpose of optimizing sampling efficiency. Finally, the method was applied to the analysis of these compounds in the air of a suburban area with small industrial plants in order to evaluate the feasibility of the proposed sampling method system, by comparing concentrations of native compounds acquired during simultaneous daily and weekly sampling.     

Evaluation of a fluorometric method for measuring low concentrations of ammonia in ambient air

A fluorometric method developed for measuring low concentrations of ammonium in marine and freshwater ecosystems was adapted for the analysis of ammonia in ambient air. The modified method entails collection of samples on an acid-treated solid adsorbent followed by analysis using a fluorometer. Optimal results were obtained using a commercially available sorbent tube containing 100 mg of acid-treated silica gel for sample collection, and an analytical protocol consisting of sample desorption in DI water, addition of orthopthaldialdehyde (OPA) working reagent, and room temperature incubation. Method accuracy and precision were evaluated by comparing experimentally determined quantities of ammonia to expected levels for sample loadings ranging from 0.16 [micro sign]g to 550 [micro sign]g-accuracy was generally within +/-20%. The estimated LOQ for the method is 0.08 [micro sign]g ammonia per sample which represents a 25-375-fold improvement in sensitivity compared to current NIOSH and OSHA methods for the measurement of ammonia in ambient air. The new method should be useful for applications requiring measurement of low concentrations of ammonia using personal sampling equipment or in the characterization of short-term fluctuations of ammonia concentrations in air.     

Diurnal concentrations variations,size distributions for ambient air particles and metallic pollutants (Cr,Mn, Ni,Cd, Pb) during summer season at a traffic area

This study characterized and discussed particulate ambient air particulate concentrations and seasonal variations for PM₁₈, PM₁₀, PM_2.5, and PM₁ during June 2013–July 2013 at this traffic sampling site. In addition, this study also characterized the ambient air particulates size distributions by using MOUDI-100S4 sampler to collect 1-day the ambient suspended particles (PM₁₈, PM₁₀, PM_2.5, and PM₁) at this sampling site. In addition, the study also showed that the main pollutants contributions were from traffic and residual areas. As for the pollutants seasonal concentrations variations, the results indicated that the average particle concentrations orders were all displayed as daytime?>?nighttime for PM₁₈, PM₁₀, PM_2.5 and PM₁ at this characteristic sampling site. The results further indicated that the mean highest of metal concentrations in this study indicated that the average metal concentration were all displayed as Mn?>?Cr?>?Ni?>?Pb?>?Cd for PM₁₈, PM₁₀, PM_2.5 and PM₁ on daytime and nighttime at this characteristic sampling site.     

Removal and recovery of metals from a coal pile runoff

The removal and recovery of heavy metals from a coal pilerunoff water using a mixture of multiple metal-tolerantbacterial strains of ATCC 55673, and ATCC 55674 and a Pseudomonas sp. was investigated. The analysis of elementalcomposition of metal precipitates recovered from the bacterialbiomass by transmission electron microscopy and energy dispersiveX-ray analysis revealed the presence of metals originally presentin the wastewater. In addition, analysis of metals in culturesupernatant and bacterial biomass by inductively coupled plasmaemission spectroscopy (ICP-ES) indicated a removal range of 82-100% and a recovery of 15-58% of metals from the wastewater and bacterial biomass, respectively.     

我国4个大城市空气PM_(2.5)、PM_(10)污染及其化学组成

报告了 1 995～ 1 996年在中国的广州、武汉、兰州、重庆 4大城市 8个采样点 PM2 .5 、PM2 .5～ 1 0 和 PM1 0 的监测结果。结果表明 ,1 995年 PM2 .5 年均值浓度为 57～ 1 60 μg/m3,比美国 1 997年颁布的标准值 (1 5μg/m3)高 2 .8～ 9.7倍。PM1 0 年日均值为 95～ 2 73μg/m3。除武汉市 1个对照点外 ,其余 7个监测点的 PM1 0 均超过我国空气质量二极标准 (1 0 0μg/m3)2 8%～ 1 73 % ,比美国标准 (50μg/m3)超过更多 ,说明污染是相当严重的。用 XRF分析了 PM2 .5 、PM2 .5～ 1 0 中 4 2种化学元素 ,结果表明 ,燃煤、燃油和其它工业污染的元素 As、Pb、Se、Zn、Cu、Cl、Br、S在这些颗粒物中有明显富集 ,特别是在PM2 .5 中的富集倍数达数十倍至数万倍 ,对人体健康有很大危害     

Validation of a standardized portable fluorescence method for determining trace beryllium in workplace air and wipe samples

Beryllium is widely used in industry for its unique properties; however, occupational exposure to beryllium particles can cause potentially fatal disease. Consequently, exposure limits for beryllium particles in air and action levels on surfaces have been established to reduce exposure risks for workers. Field-portable monitoring methods for beryllium are desired in order to facilitate on-site measurement of beryllium in the workplace, so that immediate action can be taken to protect human health. In this work, a standardized, portable fluorescence method for the determination of trace beryllium in workplace samples, i.e., air filters and dust wipes, was validated through intra- and inter-laboratory testing. The procedure entails extraction of beryllium in 1% ammonium bifluoride (NH(4)HF(2), aqueous), followed by fluorescence measurement of the complex formed between beryllium ion and hydroxybenzoquinoline sulfonate (HBQS). The method detection limit was estimated to be less than 0.02 microg Be per air filter or wipe sample, with a dynamic range up to greater than 10 microg. The overall method accuracy was shown to satisfy the accuracy criterion (A< or = +/-25%) for analytical methods promulgated by the US National Institute for Occupational Safety and Health (NIOSH). Interferences from numerous metals tested (in >400-fold excess concentration compared to that of beryllium) were negligible or minimal. The procedure was shown to be effective for the dissolution and quantitative detection of beryllium extracted from refractory beryllium oxide particles. An American Society for Testing and Materials (ASTM) International voluntary consensus standard based on the methodology has recently been published.     

A dynamic analysis of the global warming potential associated with air conditioning at a city scale: an empirical study in Shenzhen,China

Heating, ventilation and air conditioning (HVAC) systems are a major source of energy consumption in buildings, directly and indirectly contributing to greenhouse gas (GHG) emissions. In the urban environment, and depending on local climatic conditions, air conditioning units attribute to these high energy demands. This study analyzes the use of residential air conditioning units and their associated global warming potential (GWP) between 2005 and 2030 for the city of Shenzhen, a fast-growing megacity located in Southern China. A life cycle assessment approach was adopted to quantify the GWP impacts which arise from both direct (refrigerant release) and indirect (energy consumption) sources, in combination with a materials flow analysis approach. The results show that the total GWP (expressed as carbon dioxide equivalents, CO₂ eq.) from residential air conditioning systems increased from 2.2 ± 0.2 to 5.1 ± 0.4 million tonnes (Mt) CO₂ eq. between 2005 and 2017, with energy consumption and refrigerant release contributing to 72.5% and 27.5% of the total demands, respectively. Immediate measures are required to restrict refrigerant release and reduce the energy consumption of air conditioning units, to help mitigate the predicted additional total emissions of 36.4 Mt. CO₂ eq. potentially released between 2018 and 2030. This amount equals to approximately New Zealand's national CO₂ emissions in 2017. The findings proposed in this study targets air conditioning units to reduce the GWP emissions in cities, and provide useful data references and insights for local authorities to incentivise measures for improving building energy efficiency management and performance.     

Plants as indicators of urban air pollution (ozone and trace elements) in Pisa, Italy

A biennial integrated survey, based on the use of vascular plants for the bioindication of the effects of tropospheric ozone, was performed in the area of Pisa (Tuscany, Central Italy). It also investigated the distribution of selected trace elements in plants and the data were compared with those obtained from the use of passive samplers, automatic analysers of ozone and lichen biodiversity. Photochemically produced ozone proved to be present during the warm season, with maximum hourly means surpassing 100 ppb: the use of supersensitive tobacco Bel-W3 confirmed the value of detailed, cost-effective, monitoring surveys. Trials with clover clones demonstrate that sensitive plants undergo severe biomass reduction in the current ozone regime. The mean NC-S (clover clone sensitive to ozone):NC-R (resistant) biomass ratio ranged from 0.7 (in 1999) to 0.5 (in 2000). The economic impact of these reductions deserves attention. The data obtained using passive ozone samplers exceeded those obtained using an automatic analyser. The mapping of epiphytic lichen biodiversity was not related to the geographical ozone distribution as can be seen from the tobacco's response. Lettuce plants grown under standardized conditions were used positively as bioaccumulators of trace elements: Pb was abundantly recovered, but a large portion of this element was removed by washing.