钛基催化剂的制备及其催化氧化苯乙烯性能

采用溶胶凝胶法制备负载型催化剂MnOx/TiO2和V2O5/TiO2,对比选择MnOx/TiO2催化剂。考察了锰系催化剂的活性组分负载量、焙烧温度及Ce掺杂量对催化氧化苯乙烯的影响,并结合XRD、BET和SEM表征手段对催化剂进行微观分析。结果表明,MnOx/TiO2对苯乙烯有良好的催化活性,Mn与Ti的摩尔比为0.1,焙烧温度为500℃时,起燃温度T50仅为150℃,当反应温度为254℃时,苯乙烯去除率超过90%。当掺杂Ce后催化剂MnOx-CeO2/TiO2对苯乙烯催化燃烧的起燃温度和完全转化温度均有明显降低,催化剂表面燃烧物颗粒的粒径有所减小,分散均匀,更有利于苯乙烯的催化燃烧处理。     

掺硫改性TiO2对活性艳红X-3B的光催化降解性能研究

以硫脲为硫的源物质,以钛酸四丁酯为TiO2的前驱体,采用溶胶-凝胶法制备了掺硫改性TiO2光催化剂.以活性艳红X-3B为目标污染物,研究了该催化剂的光催化降解性能,对硫掺杂量、催化剂焙烧温度、溶液pH值以及催化剂添加量等影响因素进行了研究,并采用XRD分析手法对光催化剂进行表征.结果表明,经掺硫改性后的TiO2的催化活性有了很大提高,且硫的掺杂有一个最佳值,即Ti:S的摩尔比为1:1.经掺硫改性的TiO2在可见光区具备一定的催化活性,180 min内对活性艳红X-3B的去除率可达35.1%,且在紫外光区的催化活性优于纯TiO2.     

Cu/La共掺杂TiO2光催化氧化水中的氨氮

采用水解-沉淀法制备了Cu/La共掺杂纳米TiO2催化剂,利用XRD、XPS和BET技术对其进行表征,并考察了在紫外灯下,共掺杂TiO2对氨氮的光催化氧化工艺条件。物相结构和比表面积测试结果表明,共掺杂催化剂具有较好的锐钛矿晶型,孔径分布为4～8 nm,Cu/La共掺杂TiO2La以La3+,Cu是以Cu2+、Cu+的形式掺杂进入TiO2的晶格。光催化实验表明:所得改性光催化剂对氨氮的去除及焦化废水的处理均具有较高的催化活性。     

Vis/Co-TiO_2/KHSO_5体系Fenton-光催化协同降解苯酚

通过溶胶-凝胶法制备了同时具有可见光(Vis)光催化和Fenton催化双重活性的Co-TiO2催化剂。通过对比Vis/Co-TiO2/KHSO5、Co-TiO2/KHSO5和Vis/Co-TiO23种体系对苯酚的降解效果,Vis/Co-TiO2/KHSO5表现出明显的Fenton-光催化协同作用。进一步研究pH值、KHSO5与苯酚摩尔比(nKHSO5∶nC6H6O)和Co-TiO2投加量(mCo-TiO2)对Fenton-光催化协同降解苯酚效果的影响。结果表明,pH=6.9、nKHSO5∶nC6H6O=10∶1、mCo-TiO2=1.0 g/L时,降解率达100%。最后,结合XRD、XPS和UV-DRS等手段和催化活性实验数据分析了Vis/Co-TiO2/KHSO5体系的催化机理。     

负载型TiO2/活性炭光催化灭活大肠杆菌(E.coli)的研究

以大肠杆菌(Escherichia coli JM 109)为研究对象,通过细菌的灭活实验研究负载型TiO2/活性炭(TiO2/AC)的灭菌性能,并利用XRD、BET和SEM对材料的晶型、晶粒尺寸、比表面积和吸附在材料上的细菌分布形态及数量进行分析.结果表明吸附在TiO2/AC上的大肠杆菌数比吸附在活性炭和TiO2都多.TiO2/AC对E.coli光催化灭活率比TiO2粉末和P25高,制备材料的热处理温度500℃和光催化反应中光强40 W都分别使TiO2/AC的光催化活性达到最大,在光催化灭活E.coti过程中,KH2PO4使催化剂活性降低程度比NaHCO3大,而两者使TiO2/AC催化活性降低程度比TiO2小,但NaHCO3对催化活性的影响是可逆的.     

微乳液法合成掺硫纳米TiO_2及其光催化性能研究

以钛酸四丁酯为钛源,硫脲为掺硫前驱物,采用聚乙二醇辛基苯基醚（Triton X-100）/正己醇/环己烷/氨水的微乳液体系合成了掺硫的纳米TiO2粉体;对其结构进行了表征,以甲基橙为目标降解物考察了其光催化性能。烧结温度通过影响TiO2的晶型转变和颗粒尺寸来影响其光催化性能,随着烧结温度的升高,TiO2的光催化性能先是提高,然后迅速降低;在600℃烧结2 h时催化剂的降解性能达到最佳。掺杂硫可提高TiO2的光催化活性,随着掺杂量的增加,催化剂对甲基橙的降解率先快速增加然后缓慢降低,当掺杂量为S/Ti（摩尔比）=0.01∶1时TiO2的光催化降解效果最好。催化剂在用量较小时迅速提高TiO2的光催化降解性能,而后随着用量的增大反而降低,当催化剂用量为1.5 g/L时,对甲基橙的降解效果最好。     

沸石负载N、Fe^3＋共掺杂TiO2催化剂制备及表征

以人造沸石为载体,采用溶胶\|凝胶法对N、Fe3+共掺杂TiO2进行负载化研究,探讨了焙烧温度、载体粒度、负载次数等因素对负载型光催化剂结构和催化活性的影响.研究了模拟太阳光下负载型光催化剂对活性染料Sumifix TQ\|Blue的降解性能,采用X 射线衍射(XRD)、扫描电镜 (SEM)和紫外-可见光漫反射吸收光谱(UV\|Vis DRS)等方法对催化剂进行了表征.结果表明,以60～80目人造沸石为载体,400 ℃下焙烧2 h、负载3次的负载型光催化剂(N/Fe3+/TiO2\|沸石催化剂)对Sumifix TQ\|Blue具有较高的降解率;N、Fe3+共掺杂发挥了两者的协同作用,增强了TiO2的紫外光吸收的同时也使其光吸收范围拓展到可见光区;而多孔材料沸石的引入也进一步提高了催化剂的催化活性.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

外负载Ce-TiO_2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭（AC）为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明：外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

纳米TiO2负载CuMnOx对二甲苯完全燃烧的催化性能研究

以金红石型纳米TiO2为载体,采用等体积浸渍法制备了负载型CuMnOx/TiOo2催化剂,研究了其对易挥发性有机物二甲苯完全燃烧反应的催化活性.结果表明,控制锰铜质量比为1:1和锰铜负载量为20%(质量分数)时,经500℃焙烧2 h制备的催化剂具有良好的催化活性,二甲苯催化燃烧的起燃温度(T10%)和完全燃烧温度(T95%)分别为155℃和270℃.由X射线衍射(XRD)分析结果得出,催化剂的主要活性相是类尖晶石Cu1.5Mn1.5O4,纳米TiO2载体对活性相有很好的分散作用,其晶粒小,使得CuMnOx/TiO2催化剂的活性高.     

Sorption and desorption of Cu and Cd by macroalgae and microalgae

The sorption and desorption of Cu and Cd by two species of brown macroalgae and five species of microalgae were studied. The two brown macroalgae, Laminaria japonica and Sargassum kjellmanianum, were found to have high capacities at pHs between 4.0 and 5.0 while for microalgae, optimum pH lay at 6.7. The presence of other cations in solution was found to reduce the sorption of the target cation, suggesting a competition for sorption sites on organisms. Sorption isotherms obeyed the Freundlich equation, suggesting involvement of a multiplicity of mechanisms and sorption sites. For the microalgae tested, Spirulina platensis had the highest capacity for Cd, followed by Nannochloropsis oculata, Phaeodactylum tricornutum, Platymonas cordifolia and Chaetoceros minutissimus. The reversibility of metal sorption by macroalgae was examined and the results show that both HCl and EDTA solutions were very effective in desorbing sorbed metal ions from macroalgae, with up to 99.5% of metals being recovered. The regenerated biomass showed undiminished sorption performance for the two metals studied, suggesting the potential of such material for use in water and wastewater treatment.     

Kinetic and structural relationships of transition monomeric and oligomeric carboxyl- and choline-esterases

The kinetic and structural relationships of eight electrophoretically pure mammalian serum and liver serine carboxylesterases (CE) and cholinesterases (ChE) have been studied. Eight CE's and ChE's, which were fully resolved but only partially purified, provided additional information. Five of the electrophoretically pure esterases were monomeric, and of these, four belonged to a new and widely distributed class. These four monomeric esterases hydrolyzed choline esters, but at widely differing rates. Thus two were termed monomeric butyrylcholinesterases, mBuChE I and II, and two were monomeric CE's (mCE). The rabbit liver mCE was not a subunit of the oligomeric CE (oCE), although the oCE also hydrolyzed choline esters at a very low rate. The complex kinetics of the mCE's, mBuChE's, oCE's, and of the oligomeric BuChE's of horse and human serum could be interpreted according to a single reaction scheme involving an allosteric site and the equation derived from it. Thus activation and inhibition at high substrate concentrations, together with sigmoidal activity versus substrate concentration plots, all of which characterize the reactions of these esterases, could be interpreted by a single scheme and equation. Structural and kinetic comparisons showed a progressive transition of properties from the oCE's through the mCE's to the oBuChE's. One of the purified mCE's was from horse serum, and it exhibited physical and kinetic properties unlike those of the liver mCE's or oCE's.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Sorption and desorption behavior of chloroanilines and chlorophenols on montmorillonite and kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Bacterial and archaeal diversity in oil fields and reservoirs and their potential role in hydrocarbon recovery and bioprospecting

Environmental Science and Pollution Research - Hydrocarbon is a primary source of energy in the current urbanized society. Considering the increasing demand, worldwide oil productions are declining...     

畜禽养殖业污染与循环经济

解决畜禽养殖业的污染问题要以充分利用资源为根本出发点，通过对污染全过程控制及废物综合利用，达到畜禽粪便的减量化、无害化、资源化，走循环经济的发展道路。     

Degradation in soil and water and ecotoxicity of rimsulfuron and its metabolites.

The degradation and ecotoxicity of sulfonylurea herbicide rimsulfuron and its major metabolites were examined in batch samples of an alluvial sandy loam and in freshwater. An HPLC-DAD method was adapted to simultaneously identify and quantify rimsulfuron and its metabolites, which was successfully validated by GC-MS analysis. In aqueous solutions, pure rimsulfuron was rapidly hydrolyzed into metabolite 1 (N-(4,6-dimethoxypyrimidin-2-yl)-N-(3-(ethylsulfonyl)-2-pyridinylurea)), which itself was transformed into the more stable metabolite 2 (N-((3-(ethylsulfonyl)-2-pyridinyl)-4,6-dimethoxy-2-pyrimidineamine)), with half-life (t(1/2)) values of 2 and 2.5 days, respectively. Hydrolysis was instantaneous under alkaline conditions (pH = 10). In aqueous suspensions of the alluvial soil (pH = 8), formulated rimsulfuron had a half-life of 7 days, whereas that of metabolite 1 was similar to that in water (about 3.5 days). The degradation of the two major metabolites was also studied in soil suspensions with the pure compounds at concentrations ranging from 1 to 10 mg l(-1). The half-life of metabolite 1 ranged from 3.9 to 5 days, close to the previous values. Metabolite 2 was more persistent and its degradation is strongly dependent on the initial concentration (C0): half-life values ranged from 8.1 to 55 days at 2-10 mg l(-1), respectively. These values are higher than those determined from the kinetics of metabolite 1 transformation into metabolite 2 (t(1/2) = 8-19 days). The ecotoxicity of the three chemicals was evaluated through their effect on Daphnia magna and Vibrio fischeri (Microtox bioassay). No effect was observed on D. magna with 24 and 48 h acute toxicity tests. Similarly, no toxic effect was observed with the Microtox test for the three chemicals in the range of concentrations tested that included the field application dose. Thus, being of low persistence and lacking acute toxicity, these chemicals present a low environmental risk. However, chronic effects should be studied in order to confirm the safety of rimsulfuron and its major metabolites.     

Isocyanatocyclohexane and isothiocyanatocyclohexane levels in urban and industrial areas and possible emission-related activities

Isocyanatocyclohexane and isothiocyanatocyclohexane are becoming relevant compounds in urban and industrial air, as they are used in important amounts in automobile industry and building insulation, as well as in the manufacture of foams, rubber, paints and varnishes. Glass multi-sorbent tubes (Carbotrap, Carbopack, Carboxen) were connected to LCMA-UPC pump samplers for the retention of iso- and isothiocyanatocyclohexanes. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). TD-GC/MS was chosen as analytical method due to its versatility and the possibility of analysis of a wide range of volatility and polarity VOC in air samples. The method was satisfactory sensitive, selective and reproducible for the studied compounds. The concentrations of iso- and isothioisocyanatocyclohexanes were evaluated in different urban, residential and industrial locations from extensive VOC air quality and odour episode studies in several cities in the Northeastern edge of Spain. Around 200–300 VOC were determined qualitatively in each sample. Higher values of iso- and isothiocyanatocyclohexane were found in industrial areas than in urban or residential locations. The concentrations ranged between n.d.−246 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively, for industrial areas. On the other hand, urban and residential locations showed concentrations ranging between n.d.−164 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively. The site location (urban or industrial), the kind and nearness of possible iso- and isothiocyanatocyclohexane emission activities (industrial or building construction) and the changes of wind regimes throughout the year have been found the most important factors influencing the concentrations of these compounds in the different places.