液固比对含重金属水泥熟料制品中重金属释放的影响

通过模拟煅烧试验制取水泥熟料,参照JGJ 55-2000（《普通混凝土配比设计规程》）制取混凝土样品,参考SR003.1和NEN 7375浸出试验,分别研究液固比对粒状及块状混凝土样品中重金属（Cr、Ni和As）释放的影响。结果表明,在不同液固比条件下粒状混凝土中的重金属浸出浓度为Cr>Ni>As,Cr、As浸出浓度基本保持不变,分别为2 500 μg/L左右和5～6 μg/L,Ni在液固比（L∶S）<6时,浸出浓度随着液固比的增加而降低,在L∶S>6时,浸出浓度较稳定,为35.7～41.5 μg/L;浸出量均随着液固比的增加而增大。液固比（L∶S）<10时,块状混凝土中重金属累积释放量及扩散系数均随液固比的增加而增大,当L∶S>10时两者基本保持不变。     

氧化亚铁硫杆菌浸提废旧线路板铜的浸出率与时间的关系

探讨氧化亚铁硫杆菌SW-02(Thiobacillus ferrooxidans SW-02)浸提废旧印刷线路板Cu的适宜浸出时间,对Cu的浸出率与时间的关系进行了研究。通过摇瓶培养的方式,在30℃,摇床转速为170 r/min条件下进行浸出实验,按不同时间间隔取样测定溶液Cu2+浓度,pH值与氧化还原电位。分析发现,线路板加入量在30 g/L及以上时,浸出40 h后浸出反应停止,而线路板加入量在15 g/L时,浸出40 h后Cu的浸出率达到70%,继续浸出,浸出率不再显著增加。研究结果表明,铜的适宜浸出时间为40 h。     

氧化亚铁硫杆菌浸出废弃线路板中铜的研究

对废弃线路板中的铜进行了细菌浸出、只有硫酸亚铁环境下的浸出及酸浸出实验,研究了不同条件对比浸出效果,研究结果表明,细菌浸出比只有硫酸亚铁存在的浸出和酸浸要快得多。研究了在线路板粉末浓度12、24、40、60和120 g/L下浸出速率的变化,结果表明, 在考察范围内,浸出速度随着加入的废弃线路板粉末浓度的升高而降低,当线路板粉末的浓度＞60 g/L时,浸出速度维持在较低水平,选取24 g/L作为浸出的线路板粉末的浓度。分别在细菌培养0、24、48和72 h时加入线路板粉末24 g/L进行浸出实验,结果表明,细菌培养时间长,使得浸出过程进行得也更快。     

有机磷酸HEDP稳定垃圾焚烧飞灰重金属的研究

研究了有机磷酸羟基亚乙基二膦酸(HEDP)对生活垃圾焚烧飞灰中重金属的稳定方法.通过对不同HEDP投加量处理后的飞灰试样作危险废物浸出毒性鉴别试验,分析HEDP最佳使用剂量,并评价了稳定化飞灰的长期稳定性.结果表明,HEDP最适使用剂量为0.03 Ml/g(以商品级HEDP与飞灰的体积质量比计),处理后飞灰与原状飞灰相比,Pb、Zn和Hg的浸出浓度分别降低了98.3%、99.5%和85.0%.HEDP对飞灰中重金属稳定效果排序为:Pb＞Zn＞Hg＞Ni＞Cu＞Cd＞CrHAs.重金属pH相关浸出测试(pH-dependent leaching tests)表明:经0.03mL/g HEDP稳定处理的飞灰,在0.3 mol/L HNO3和0.3 mol/L NaOH的浸取条件下,其重金属浸出浓度均低于国家危险废物鉴别标准,显示具有良好的长期稳定性.     

氧化亚铁硫杆菌浸出线路板中铜及过程中铁的变化研究

从煤堆积水中分离得到氧化亚铁硫杆菌,利用该菌种对线路板中的Cu进行了浸出实验.研究了不同线路板粉末添加量对浸出效果的影响,在220 mL溶液中添加量为2.2、4.4 g时Cu的浸出率很快达到了90%,而添加量为11.0、22.0 g时浸出率表现了缓慢上升,在15 d左右达到了90%.观察了浸出过程中铁浓度及价态的变化,结果表明,浸出初期随着添加量的增加,Fe2 增加明显,但是随着浸出时间的推移,Fe3 、Fe2 和总Fe都呈现降低趋势.     

生活垃圾焚烧炉渣湿法处理前后化学特性表征

选取4个地区(编号为C、X、N、J)生活垃圾焚烧炉渣及其湿法处理后炉渣(分别称为原生炉渣及集料),针对元素成分、氧化物组分及重金属与溶盐的毒性浸出特性等开展实验分析。结果表明:(1)与原生炉渣对比,集料的化学元素含量变化较大,主要元素Si、Al、C含量均不同程度增加,而Cl、Fe及重金属Zn、Pb、Cr、Cu等含量基本降低;集料中SiO2和Al2O3均明显增加。(2)除C原生炉渣浸出液中Ni(7.62mg/L)严重超标外,其他3种原生炉渣浸出液中Pb、Cu、Ni浸出浓度均低于《危险废物鉴别标准浸出毒性鉴别》(GB 5085.3—2007)中浸出毒性鉴别标准值。与原生炉渣相比,除N集料外,其余集料浸出液中3种重金属(Pb、Cu、Ni)含量基本下降,特别是C集料浸出液中Ni浸出质量浓度下降到低于检测限;集料浸出液中Cl-和SO24-浸出浓度均下降,Cl-浸出质量浓度在C集料浸出液中下降最多,约下降72%,SO24-浸出质量浓度在J集料浸出液中下降最多,约下降86%。     

有机磷酸HEDP稳定垃圾焚烧飞灰重金属的研究

研究了有机磷酸羟基亚乙基二膦酸（HEDP）对生活垃圾焚烧飞灰中重金属的稳定方法.通过对不同HEDP投加量处理后的飞灰试样作危险废物浸出毒性鉴别试验,分析HEDP最佳使用剂量,并评价了稳定化飞灰的长期稳定性.结果表明,HEDP最适使用剂量为0.03 Ml/g（以商品级HEDP与飞灰的体积质量比计）,处理后飞灰与原状飞灰相比,Pb、Zn和Hg的浸出浓度分别降低了98.3%、99.5%和85.0%.HEDP对飞灰中重金属稳定效果排序为：Pb＞Zn＞Hg＞Ni＞Cu＞Cd＞CrHAs.重金属pH相关浸出测试（pH-dependent leaching tests）表明：经0.03mL/g HEDP稳定处理的飞灰,在0.3 mol/L HNO3和0.3 mol/L NaOH的浸取条件下,其重金属浸出浓度均低于国家危险废物鉴别标准,显示具有良好的长期稳定性.     

氧化亚铁硫杆菌浸出线路板中铜的研究

从煤堆积水中分离得到氧化亚铁硫杆菌,利用该菌种对线路板中的铜进行了浸出实验.研究了不同线路板粉末添加量对浸出效果的影响,观察了浸出过程中pH和氧化还原电位(Eh)的变化,结果表明添加量为10 g/L和20 g/L时,在15 d内线路板Cu几乎全部浸出,而50g/L和100g/L在15 d内亦有较高的浸出效率,并呈持续上升趋势.     

木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂对二元重金属离子溶液中Pb^2＋的吸附

采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2＋/Pb2＋和Zn2＋/Pb2＋溶液中的吸附性能进行了较系统考察。Pb2＋离子溶液中存在竞争离子Cu2＋、Zn2＋时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对Pb2＋的吸附量明显下降,而竞争离子吸附量显著增加。二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2＋、Zn2＋的吸附量大于对Pb2＋的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对Pb2＋离子的吸附量下降迅速。随吸附树脂用量增加,竞争离子Cu2＋、Zn2＋的吸附量逐渐减小,Pb2＋的吸附量在吸附树脂用量0.10 g/L（Zn2＋/Pb2＋溶液）或0.15 g/L（Cu2＋/Pb2＋溶液）时出现最大值。溶液pH值对树脂吸附性能有显著影响。3.0     

木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂对二元重金属离子溶液中Pb2+的吸附

采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2 +/pb2和Zn2+/pb2+溶液中的吸附性能进行了较系统考察.pb2+离子溶液中存在竞争离子Cu2+、Zn2+时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对pb2+的吸附量明显下降,而竞争离子吸附量显著增加.二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2+、Zn2+的吸附量大于对pb2+的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对pb2+离子的吸附量下降迅速.随吸附树脂用量增加,竞争离子Cu2+、Zn2+的吸附量逐渐减小,pb2+的吸附量在吸附树脂用量0.10 g/L(Zn2 +/pb2+溶液)或0.15 g/L(Cu2+/pb2+溶液)时出现最大值.溶液pH值对树脂吸附性能有显著影响.3.0＜pH＜5.O时,3种树脂对竞争离子和pb2+的吸附量快速增大;5＜ pH ＜9时,树脂对竞争离子和pb2+的吸附量基本不变;9＜pH＜ll时,树脂对pb2+的吸附量减小,而对竞争离子的吸附量或增大或减小.     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

嗜盐菌的特性与高盐废水生物处理的进展

论述了嗜盐菌的形态特征、营养构成、生理特性和嗜盐机理，以及利用其特性在含盐有机废水处理中的应用，综述了国内外生化处理高含盐量有机工业废水的实验研究成果、在实际废水工程中的应用及其发展方向。对嗜盐菌的培养与驯化有一定的参考价值，对含盐废水处理工程的设计与运行有指导意义。