国外环境文献索引

RevieW(综述)·Kempen R V.Overview:full scale experience of SHARON Process for treatment of rejection water of digested sludge dewatering.Water Science& Technology,2001,44(1):145-152. (综述:用于处理菌致分解污泥脱水的废水 SHARON工艺全尺度经验)·Bode H.Nutrient removal in the river basin of the Ruhr-a German case study.Water Science&Tech-nology,2001,44(1):15-25.(德国鲁尔区流域中营养素排除法实例研究)     

Validation of a conductometric bienzyme biosensor for the detection of proteins as marker of organic matter in river samples

This article describes a conductometric bi-layer based bienzyme biosensor for the detection of proteins as a marker of organic matter in rivers. Proteins were chosen to be used as indicators of urban pollution. The working mechanism of the bienzyme biosensor is based on the enzymatic hydrolysis of proteins into several fractions (peptides and amino acids), which results in a local conductivity change depending of the concentration of proteins. In this work, we began with the optimization of biosensor response using bovine serum albumin (BSA) as standard protein. For this objective seven enzymatic biosensors were prepared: four enzymatic sensors with only one layer of enzyme (proteinase K, trypsin, pronase or protease X) and three other enzymatic sensors with two layers (first layer: membrane containing proteinase K; second layer: one of the three other enzymes: trypsin, pronase or protease X). The biosensors were obtained through the deposition of enzymatic layers and the cross-linking process between enzymes and BSA in saturated glutaraldehyde vapour. The response of the various biosensors, described previously, were compared with the values of total organic carbon (TOC), and those of organic nitrogen (Norg), as determined by the laboratory accredits (CEMAGREF of Lyon) using the traditional method of analysis (NF EN 1484, infrared spectroscopy) and (NF EN 25663, mineralization/colorimetry assay) respectively for each water sample obtained from di erent sites in Lyon (France). The linear correlations obtained with the response of the seven biosensors showed the most important indices of correlations for the biosensor with two enzymatic layers: proteinase K + pronase (pkp). The optimum conditions for the preparation of the pkp biosensor increased the sensitivity and gave a limit of quantification of 0.583 g/L for TOC and 0.218 g/L for Norg in water samples. This sensor shows good reproducibility (2.28%), a capacity to be used at temperatures range 10– 30°C (depending on the season) and moreover a long lifetime (5 weeks).     

Effect of copper on the degradation of pesticides cypermethrin and cyhalothrin

The influence of coexisting copper (Cu) ion on the degradation of pesticides pyrethroid cypermethrin and cyhalothrin in soil and photodegradation in water system were studied.Serial concentrations of the pesticides with the addition of copper ion were spiked in the soil and incubated for a regular period of time,the analysis of the extracts from the soil was carried out using gas chromatography (GC).The photodegradation of pyrethroids in water system was conducted under UV irradiation.The effect of Cu~(2 ) on the pesticides degradation was measured with half life (t_(0.5)) of degradation.It was found that a negative correlation between the degradation of the pyrethroid pesticides in soil and Cu addition was observed.But Cu~(2 ) could accelerate photodegradation of the pyrethroids in water.The t_(0.5) for cyhalothrin extended from 6.7 to 6.8 d while for cypermethrin extended from 8.1 to 10.9 d with the presence of copper ion in soil.As for photodegradation,t_(0.5) for cyhalothrin reduced from 173.3 to 115.5 rain and for cypermethrin from 115.5 to 99.0 min.The results suggested that copper influenced the degradation of the pesticides in soil by affecting the activity of microorganisms.However, it had catalyst tendency for photodegradation in water system.The difference for the degradation efficiency of pyrethroid isomers in soil was also observed.Copper could obviously accelerate the degradation of some special isomers.     

Practical performance and its efficiency of arsenic removal from groundwater using Fe-Mn binary oxide

A treatment unit packed by granular adsorbent of Fe-Mn binary oxide incorporated into diatomite (FMBO(1:1)-diatomite) was studied to remove arsenic from anaerobic groundwater without any pre-treatment or post-treatment. The raw anaerobic groundwater containing 35-45 μg/L of arsenic was collected from suburb of Beijing. Arsenic(III) constituted roughly 60%-80% of the total arsenic content. Approximately 7,000 bed volumes (ratio of efluent volume to adsorbent volume) treated water with arsenic concentration below 10 μg/L were produced in the operation period of four months. The regeneration of FMBO(1:1)-diatomite had been operated for 15 times. In the first stage, the regeneration process significantly improved the adsorption capacity of FMBO(1:1)-diatomite. With increased loading amount of Fe-Mn binary oxide, the adsorption capacity for arsenic decreased 20%-40%. Iron and manganese in anaerobic groundwater were oxidized and adsorptive filtrated by FMBO(1:1)-diatomite efficiently. The final concentrations of iron and manganese in efluents were nearly zero. The continued safe performance of the treatment units proved that adsorbent FMBO(1:1)-diatomite had high oxidation ability and exhibited strong adsorptive filtration.     

A screen-printed, amperometric biosensor for the determination of organophosphorus pesticides in water samples

An amperometric biosensor based on screen-printed electrodes (SPEs) was developed for the determination of organophosphorus pesticides in water samples. The extent of acetylcholinesterase (AChE) deactivation was determined and quantified for pesticide concentrations in water samples. An enzyme immobilization adsorption procedure and polyacrylamide gel matrix polymerization were used for fabrication of the biosensor, with minimal losses in enzyme activity. The optimal conditions for enzyme catalytic reaction on the SPEs surfaces were acetylthiocholine chloride (ATChCl) concentration of 5 mmol/L, pH 7 and reaction time of 4 min. The detection limits for three organophosphorus pesticides (dichlorvos, monocrotophs and parathion) were in the range of 4 to 7 g/L when an AChE amount of 0.1 U was used for immobilization.     

Characteristics of particulate-bound polycyclic aromatic hydrocarbons emitted from industrial grade biomass boilers

Polycyclic aromatic hydrocarbons(PAHs) are carcinogenic or mutagenic and are important toxic pollutants in the flue gas of boilers. Two industrial grade biomass boilers were selected to investigate the characteristics of particulate-bound PAHs: one biomass boiler retro-fitted from an oil boiler(BB1) and one specially designed(BB2) biomass boiler. One coal-fired boiler was also selected for comparison. By using a dilution tunnel system, particulate samples from boilers were collected and 10 PAH species were analyzed by gas chromatography–mass spectrometry(GC–MS). The total emission factors(EFs) of PAHs ranged from 0.0064 to0.0380 mg/kg, with an average of 0.0225 mg/kg, for the biomass boiler emission samples. The total PAH EFs for the tested coal-fired boiler were 1.8 times lower than the average value of the biomass boilers. The PAH diagnostic ratios for wood pellets and straw pellets were similar.The ratio of indeno(1,2,3-cd)pyrene/[indeno(1,2,3-cd)pyrene + benzo(g,h,i)perylene] for the two biomass boilers was lower than those of the reference data for other burning devices, which can probably be used as an indicator to distinguish the emission of biomass boilers from that of industrial coal-fired boilers and residential stoves. The toxic potential of the emission from wood pellet burning was higher than that from straw pellet burning, however both of them were much lower than residential stove exhausts.     

A profile of environmental science in China

This paper concisely introduced the eco-environmental survey in China and the Chinese scientific programme for environmental research which is being practiced or being planned. China has established a nation-wide system relating to environmental scientific research and environmental administration and has taken the following strategies for solving the environment problems: (1) a series of laws and regulations for environmental protection has been promulgated so as to strengthen the legal administration and economic punishment. (2) the idea of ecological construction has been proposed for the purpose of taking the environmental protection work into the consideration of the national and provincial (or regional) economic construction planning. (3) spreading ecological engineering and ecological technologies have reduced the pollutant sources and have increased the industrial and agricultural economic profit.     

Preparation and evaluation of Zr-β-FeOOH for efficient arsenic removal

A Zr-β-FeOOH adsorbent for both As(V) and As(III) removal was prepared by a chemical co-precipitation method.Compared with β-FeOOH,the addition of Zr enhanced the adsorption capacities for As(V) and As(III),especially As(III).The maximum adsorption capacities for As(III) and As(V) were 120 and 60mg/g respectively at pH 7.0,much higher than for many reported adsorbents.The adsorption data accorded with Freundlich isotherms.At neutral pH,for As(V),adsorption equilibrium was approached after 3 hr,while for As(III),adsorption equilibrium was approached after 5 hr.Kinetic data fitted well to the pseudo second-order reaction model.As(V) elimination was favored at acidic pH,whereas the adsorption of As(III) by Zr-β-FeOOH was found to be effective over a wide pH range of 4-10.Competitive anions hindered the adsorption according to the sequence:phosphate > silicate > bicarbonate > sulfate > nitrate,while Ca2+ and Mg2+ increased the removal of As(III) and As(V) slightly.The high adsorption capability and good performance in other aspects make Zr-β-FeOOH a potentially attractive adsorbent for the removal of both As(III) and As(V) from water.     

Combined effects of adsorption and photocatalysis by hybrid TiO2/ZnO-calcium alginate beads for the removal of copper

The use of nanosized titanium dioxide(TiO_2) and zinc oxide(ZnO) in the suspension form during treatment makes the recovering and recycling of photocatalysts difficult.Hence,supported photocatalysts are preferred for practical water treatment applications.This study was conducted to investigate the efficiency of calcium alginate(CaAlg) beads that were immobilized with hybrid photocatalysts,TiO_2/ZnO to form TiO_2/ZnO-CaAlg.These immobilized beads,with three different mass ratios of TiO_2:ZnO(1:1,1:2,and 2:1) were used to remove Cu(Ⅱ) in aqueous solutions in the presence of ultraviolet light.These beads were subjected to three cycles of photocatalytic treatment with different initial Cu(Ⅱ) concentrations(10-80 ppm).EDX spectra have confirmed the inclusion of Ti and Zn on the surface of the CaAlg beads.Meanwhile,the surface morphology of the beads as determined using SEM,has indicated differences of before and after the photocatalytic treatment of Cu(Ⅱ).Among all three,the equivalent mass ratio TiO_2/ZnO-CaAlg beads have shown the best performance in removing Cu(Ⅱ) during all three recycling experiments.Those TiO_2/ZnO-CaAlg beads have also shown consistent removal of Cu,ranging from 7.14-52.0 ppm(first cycle) for initial concentrations of10-80 ppm.In comparison,bare CaAlg was only able to remove 6.9-48 ppm of similar initial Cu concentrations.Thus,the potential use of TiO_2/ZnO-CaAlg beads as environmentally friendly composite material can be further extended for heavy metal removal from contaminated water.     

Cost-performance analysis of nutrient removal in a full-scale oxidation ditch process based on kinetic modeling

A full-scale oxidation ditch process for treating sewage was simulated with the ASM2d model and optimized for minimal cost with acceptable performance in terms of ammonium and phosphorus removal. A unified index was introduced by integrating operational costs (aeration energy and sludge production) with effluent violations for performance evaluation. Scenario analysis showed that,in comparison with the baseline (all of the 9 aerators activated), the strategy of activating 5 aerators could save aeration energy significantly with an ammonium violation below 10%. Sludge discharge scenario analysis showed that a sludge discharge flow of 250–300 m3/day (solid retention time (SRT), 13–15 days) was appropriate for the enhancement of phosphorus removal without excessive sludge production. The proposed optimal control strategy was: activating 5 rotating disks operated with a mode of "111100100" ( "1"represents activation and "0" represents inactivation) for aeration and sludge discharge flow of 200 m3/day (SRT, 19 days). Compared with the baseline, this strategy could achieve ammonium violation below 10% and TP violation below 30% with substantial reduction of aeration energy cost (46%) and minimal increment of sludge production (< 2%). This study provides a useful approach for the optimization of process operation and control.     

Association of emergency room visits for respiratory diseases with sources of ambient PM2.5

Previous studies have reported associations of short-term exposure to different sources of ambient fine particulate matter(PM_(2.5)) and increased mortality or hospitalizations for respiratory diseases. Few studies, however, have focused on the short-term effects of source-specific PM_(2.5) on emergency room visits(ERVs) of respiratory diseases. Source apportionment for PM_(2.5) was performed with Positive Matrix Factorization(PMF) and generalized additive model was applied to estimate associations between source-specific PM_(2.5) and respiratory disease ERVs. The association of PM_(2.5) and total respiratory ERVs was found on lag4(RR = 1.011, 95%CI: 1.002, 1.020) per interquartile range(76 μg/m~3) increase.We found PM_(2.5) to be significantly associated with asthma, bronchitis and chronic obstructive pulmonary disease(COPD) ERVs, with the strongest effects on lag5(RR = 1.072,95%CI: 1.024, 1.119), lag4(RR = 1.104, 95%CI: 1.032, 1.176) and lag3(RR = 1.091, 95%CI: 1.047,1.135), respectively. The estimated effects of PM_(2.5) changed little after adjusting for different air pollutants. Six primary PM_(2.5) sources were identified using PMF analysis, including dust/soil(6.7%), industry emission(4.5%), secondary aerosols(30.3%), metal processing(3.2%),coal combustion(37.5%) and traffic-related source(17.8%). Some of the sources were identified to have effects on ERVs of total respiratory diseases(dust/soil, secondary aerosols, metal processing, coal combustion and traffic-related source), bronchitis ERVs(dust/soil) and COPD ERVs(traffic-related source, industry emission and secondary aerosols). Different sources of PM_(2.5) contribute to increased risk of respiratory ERVs to different extents, which may provide potential implications for the decision making of air quality related policies, rational emission control and public health welfare.     

Two-step fast microwave-assisted pyrolysis of biomass for bio-oil production using microwave absorbent and HZSM-5 catalyst

A novel technology of two-step fast microwave-assisted pyrolysis(f MAP) of corn stover for bio-oil production was investigated in the presence of microwave absorbent(Si C) and HZSM-5catalyst. Effects of f MAP temperature and catalyst-to-biomass ratio on bio-oil yield and chemical components were examined. The results showed that this technology, employing microwave, microwave absorbent and HZSM-5 catalyst, was effective and promising for biomass fast pyrolysis. The f MAP temperature of 500°C was considered the optimum condition for maximum yield and best quality of bio-oil. Besides, the bio-oil yield decreased linearly and the chemical components in bio-oil were improved sequentially with the increase of catalyst-to-biomass ratio from 1:100 to 1:20. The elemental compositions of bio-char were also determined. Additionally, compared to one-step f MAP process, two-step f MAP could promote the bio-oil quality with a smaller catalyst-to-biomass ratio.     

Immobilization of lead in anthropogenic contaminated soils using phosphates with/without oxalic acid

Understanding the effects of oxalic acid(OA) on the immobilization of Pb(Ⅱ) in contaminated soils by phosphate materials, has considerable benefits for risk assessment and remediation strategies for the soil. A series of phosphate amendments with/without oxalic acid were applied to two anthropogenic contaminated soils. We investigated the immobilization of Pb(Ⅱ) by KH2PO4, phosphate rock(PR), activated phosphate rock(APR) and synthetic hydroxyapatite(HAP) at different phosphate:Pb(P:Pb) molar ratios(0, 0.6, 2.0 and 4.0) in the presence/absence of 50 mmol oxalic acid/kg soil, respectively. The effects of treatments were evaluated using single extraction with deionized water or Ca Cl2, Community Bureau of Reference(BCR) sequential extraction and toxicity characteristic leaching procedure(TCLP)methods. Our results showed that the concentration of water extractable, exchangeable and TCLP-Pb all decreased with incubation time. The concentration of water-extractable Pb after120 days was reduced by 100% when soils were amended with APR, HAP and HAP + OA, and the TCLP-Pb was 5 mg/L for the red soil at P:Pb molar ratio 4.0. Water-soluble Pb could not be detected and the TCLP-Pb was 5 mg/L at all treatments applied to the yellow-brown soil. BCR results indicated that APR was most effective, although a slight enhancement of water-soluble phosphate was detected at the P:Pb molar ratio 4.0 at the beginning of incubation. Oxalic acid activated phosphates, and so mixing insoluble phosphates with oxalic acid may be a useful strategy to improve their effectiveness in reducing Pb bioavailability.     

Distribution of polychlorinated biphenyls in effluent from a large municipal wastewater treatment plant: Potential for bioremediation?

This study involved an evaluation of the potential for bioremediation of polychlorinated biphenyls(PCBs) in the effluent from a large municipal wastewater treatment plant. It was focused on the presence of PCBs in two types of effluents: the continuous effluent present during dry weather conditions and the intermittently present effluent that was present during wet weather due to incoming stormwater. The annual discharge of PCBs for both types of effluent was calculated based on a five-year dataset(2011–2015). In addition, the toxicity and bioremediation potential of the PCBs in the effluent were also assessed. It was found that the continuous effluent was responsible for the majority of the discharged PCB into the receiving river(1821 g for five years), while the intermittent effluent contributed 260 g over the five years.The average number of chlorine per biphenyl for the detected PCB congeners showed a 19%difference between the two types of effluent, which indicated a potential for organohalide respiration of PCBs during the continuous treatment. This was further supported by a high level of tri-, tetra-and penta-chlorinated congeners accounting for 75% of the anaerobically respired PCBs. Potential for aerobic degradation and thus biomineralization of PCBs was identified for both effluents. Furthermore, toxicity of 12 dioxin-like PCBs showed that normal operation of the wastewater reduced the toxicity throughout the wastewater treatment plant.     

JOURNAL OF ENVIRONMENTAL SCIENCES

(http://www.jesc.ac.cn)Aims and scope Journal of Environmental Sciences is an international academic journal supervised by Research Center for Eco-Environ-mental Sciences, Chinese Academy of Sciences.     

Fluorescence regional integration and differential fluorescence spectroscopy for analysis of structural characteristics and proton binding properties of fulvic acid sub-fractions

Structural characteristics and proton binding properties of sub-fractions (FA3–FA13) of fulvic acid (FA), eluted stepwise by pyrophosphate buffer were examined by use of fluorescence titration combined with fluorescence regional integration (FRI) and differential fluorescence spectroscopy (DFS). Humic-like (H-L) and fulvic-like (F-L) materials, which accounted for more than 80% of fluorescence response, were dominant in five sub-fractions of FA. Based on FRI analysis, except the response of F-L materials in FA9 and FA13, maximum changes in percent fluorescence response were less than 10% as pH was increased from 2.5 to 11.5. Contents of carboxylic and phenolic groups were compared for fluorescence peaks of FA sub-fractions based on pH-dependent fluorescence derived from DFS. Static quenching was the dominant mechanism for binding of protons by FA sub-fractions. Dissociation constants (pKa) were calculated by use of results of DFS and the modified Stern-Volmer relationship. The pKa of H-L, F-L, tryptophan-like and tyrosine-like materials of FA sub-fractions exhibited ranges of 3.17–4.06, 3.12–3.97, 4.14–4.45 and 4.25–4.76, respectively, for acidic pHs. At basic pHs, values of pKa for corresponding materials were in ranges of 9.71–10.24, 9.62–10.99, 9.67–10.31 and 9.33–10.28, respectively. At acidic pH, protein-like (P-L) materials had greater affinities for protons than did either H-L or F-L materials. The di-carboxylic and phenolic groups were likely predominant sites of protonation for both H-L and F-L materials at both acidic and basic pHs. Amino acid groups were significant factors during proton binding to protein-like materials of FA sub-fractions at basic pH.     

Adsorption and desorption of Cu(Ⅱ) and Pb(Ⅱ) in paddy soils cultivated for various years in the subtropical China

The adsorption and desorption of Cu(Ⅱ) and Pb(Ⅱ) on upland red soil,and paddy soils which were originated from the upland soil and cultivated for 8,15,35 and 85 years,were investigated using the batch method.The study showed that the organic matter content and cation exchange capacity (CEC) of the soils are important factors controlling the adsorption and desorption of Cu(Ⅱ) and Pb(Ⅱ).The 15-Year paddy soil had the highest adsorption capacity for Pb(Ⅱ),followed by the 35-Year paddy soil.Both the 35-Year paddy soil and 15-Year paddy soil adsorbed more Cu(Ⅱ) than the upland soil and other paddy soils.The 15-Year paddy soils exhibited the highest desorption percentage for both Cu(Ⅱ) and Pb(Ⅱ).These results are consistent with the trend for the CEC of the soils tested.The high soil CEC contributes not only to the adsorption of Cu(Ⅱ) and Pb(Ⅱ) but also to the electrostatic adsorption of the two heavy metals by the soils.Lower desorption percentages for Cu(Ⅱ) (36.7% to 42.2%) and Pb(Ⅱ) (50.4% to 57.9%) were observed for the 85-Year paddy soil.The highest content of organic matter in the soil was responsible for the low desorption percentages for the two metals because the formation of the complexes between the organic matter and the metals could increase the stability of the heavy metals in the soils.     

Are current Chinese national ambient air quality standards on 24-hour averages for particulate matter sufficient to protect public health?

With rapid economic development and urbanization in recent decades, China has experienced the worsening of ambient air quality. For better air quality management to protect human health, Chinese government revised national ambient air quality standards(NAAQS) for particulate matter(PM) in 2012(GB3095-2012). To assess the effectiveness of current NAAQS for PM on public health in Chinese population, we conducted a metaanalysis on published studies examining the mortality risk of short-term exposure to PM with aerodynamic diameters less than 10 and 2.5 μm(PM_(10) and PM_(2.5)) in China. The reported24-hour concentrations of PM_(10) and PM_(2.5) in studies ranged from 43.5 to 150.1 μg/m~3 and 37.5 to 176.7 μg/m~3. In the pooled excess, mortality risk estimates of short-term exposure to PM.In specific, per 10 μg/m~3 increase in PM_(10), we observed increases of 0.40%(95%CI: 0.33%,0.47%), 0.57%(95%CI: 0.44%, 0.70%) and 0.49%(95%CI: 0.40%, 0.58%) in total, respiratory and cardiovascular mortality, per 10 μg/m~3 increase in PM_(2.5), we observed increases of 0.51%(95%CI: 0.38%, 0.63%), 0.62%(95%CI: 0.52%, 0.73%) and 0.75%(95%CI: 0.54%, 0.95%) in total,respiratory and cardiovascular mortality. Finally, we derived 125 μg/m~3 for PM_(10) and 62.5 μg/m~3 for PM_(2.5) as 24-hour recommendation values based on the pooled estimates. Our results indicated that current Chinese NAAQS for PM could be sufficient in mitigating the excess mortality risk from short-term exposure to ambient PM. However, future research on longterm exposure cohort studies in Chinese population is also essential in revising annual averages for PM in Chinese NAAQS.     

Dissipation of S-metolachlor and butachlor in agricultural soils and responses of bacterial communities: Insights from compound-specific isotope and biomolecular analyses

The soil dissipation of the widely used herbicides S-metolachlor(SM) and butachlor(BUT)was evaluated in laboratory microcosms at two environmentally relevant doses(15 and 150 μg/g) and for two agricultural soils(crop and paddy).Over 80% of SM and BUT were dissipated within 60 and 30 days,respectively,except in experiments with crop soil at 150 μg/g.Based on compound-specific isotope analysis(CSIA) and observed dissipation,biodegradation was the main process responsible for the observed decrease of SM and BUT in the paddy soil.For SM,biodegradation dominated over other dissipation processes,with changes of carbon isotope ratios(Δδ~(13)C) of up to 6.5‰ after 60 days,and concomitant production of ethane sulfonic acid(ESA) and oxanilic acid(OXA) transformation products.In crop soil experiments,biodegradation of SM occurred to a lesser extent than in paddy soil,and sorption was the main driver of apparent BUT dissipation.Sequencing of the 16 S rRNA gene showed that soil type and duration of herbicide exposure were the main determinants of bacterial community variation.In contrast,herbicide identity and spiking dose had no significant effect.In paddy soil experiments,a high(4:1,V/V) ESA to OXA ratio for SM was observed,and phylotypes assigned to anaerobic Clostridiales and sulfur reducers such as Desulfuromonadales and Syntrophobacterales were dominant for both herbicides.Crop soil microcosms,in contrast,were associated with a reverse,low(1:3,V/V)ratio of ESA to OXA for SM,and Alphaproteobacteria,Actinobacteria,and Bacillales dominated regardless of the herbicide.Our results emphasize the variability in the extent and modes of SM and BUT dissipation in agricultural soils,and in associated changes in bacterial communities.     

Determination of particulate polycyclic aromatic hydrocarbons in ambient air by gas chromatography-mass spectrometry after molecularly imprinted polymer extraction

A solid phase extraction procedure (SPE) is described for the quantitative analysis of polycyclic aromatic hydrocarbons (PAHs) in atmospheric particulate matter (PM), as ubiquitous environmental pollutants routinely measured in air quality monitoring. A SPE cartridge was used based on a molecular imprinted polymer (MIP-SPE) properly tailored for selective retention of PAHs with 4 and more benzene fused rings. The performance of the clean-up procedure was evaluated with the specific concern of selective purification towards saturated hydrocarbons, which are the PM components mostly interfering GC analysis of target PAHs. Under optimized operative conditions, the MIP-SPE provided analyte recovery close to 95% for heavier PAHs, from benzo(α)pyrene to benzo(ghi)perylene, and close to 90% for four benzene rings PAHs, with good reproducibility (RSDs: 2.5%-5.9%). Otherwise, C₁₇-C₃₂ n-alkanes were nearly completely removed. The proposed method was critically compared with Solid Phase Micro Extraction (SPME) using a polyacrylate fiber. Both methods were successfully applied to the analysis of ambient PM_2.5 samples collected at an urban polluted site. Between the two procedures, the MIP-SPE provided the highest recovery (R% ≥ 93%) for PAHs with 5 and more benzene rings, but lower for lighter PAHs. In contrast, SPME showed a mean acceptable R% value (∼ 80%) for all the investigated PAHs, except for the heaviest PAHs in the most polluted samples (R%: 110%-138%), suggesting an incomplete purification from the interfering n-hydrocarbons.