Advanced multivariate analysis to assess remediation of hydrocarbons in soils

Accurate monitoring of degradation levels in soils is essential in order to understand and achieve complete degradation of petroleum hydrocarbons in contaminated soils. We aimed to develop the use of multivariate methods for the monitoring of biodegradation of diesel in soils and to determine if diesel contaminated soils could be remediated to a chemical composition similar to that of an uncontaminated soil. An incubation experiment was set up with three contrasting soil types. Each soil was exposed to diesel at varying stages of degradation and then analysed for key hydrocarbons throughout 161 days of incubation. Hydrocarbon distributions were analysed by Principal Coordinate Analysis and similar samples grouped by cluster analysis. Variation and differences between samples were determined using permutational multivariate analysis of variance. It was found that all soils followed trajectories approaching the chemical composition of the unpolluted soil. Some contaminated soils were no longer significantly different to that of uncontaminated soil after 161 days of incubation. The use of cluster analysis allows the assignment of a percentage chemical similarity of a diesel contaminated soil to an uncontaminated soil sample. This will aid in the monitoring of hydrocarbon contaminated sites and the establishment of potential endpoints for successful remediation.     

Historical mercury contamination in sediments and catchment soils of Diss Mere, UK

A 5.3 m sediment core and soil samples were taken from Diss Mere and its catchment. The sediment core was dated and Hg analysed on the sediment and soil samples. The Hg record of the sediment core shows that Diss Mere has been contaminated for the past thousand years and the historical trends in sediment contamination are in good agreement with the development of the weaving industry in Diss and hemp cultivation in the region. Mercury contamination in Diss Mere has been significant and reached a peak in the mid-19th century with sediment Hg concentrations over 50 μg g⁻¹. Elevated Hg concentrations were also found in contemporary soils in residential areas with former industrial land use. Although local hemp cultivation and the traditional weaving industry were abandoned a hundred years ago, Hg contamination caused by these activities still exists in the catchment, and affects the lake.     

Metal fractionation in soils and assessment of environmental contamination in Vallecamonica, Italy

Metal contamination was investigated in soils of the Vallecamonica, an area in the northern part of the Brescia province (Italy), where ferroalloy industries were active for a century until 2001. The extent in which emissions from ferroalloy plants affected metal concentration in soils is not known in this area. In this study, the geogenic and/or anthropogenic origin of metals in soils were estimated. A modified Community Bureau of Reference sequential chemical extraction method followed by inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses were employed to evaluate the potential bioavailability of Al, Cd, Mn, Fe, Cr, Zn, and Pb in soils. Principal component analysis (PCA) was used to assess the relationships among metal sources in soil samples from different locations. This approach allowed distinguishing of different loadings and mobility of metals in soils collected in different areas. Results showed high concentrations and readily extractability of Mn in the Vallecamonica soils, which may suggest potential bioavailability for organisms and may create an environmental risk and potential health risk of human exposure.     

Use of sequential extraction to assess metal partitioning in soils

The state of heavy metal pollution and the mobility of Cd, Cu, Ni, Cr, Pb and Zn were studied in three texturally different agricultural soil profiles near a Cu-Ni smelter in Harjavalta, Finland. The pseudo-total concentrations were determined by an aqua regia procedure. Metals were also determined after division into four fractions by sequential extraction with (1) acetic acid (exchangeable and specifically adsorbed metals), (2) a reducing agent (bound to Fe/Mn hydroxides), (3) an oxidizing agent (bound to soil organic matter) and (4) aqua regia (bound to mineral structures). Fallout from the smelter has increased the concentrations of Cd, Cu and Ni in the topsoil, where 75-90% of Cd, 49-72% of Cu and 22-52% of Ni occurred in the first two fractions. Slight Pb and Zn pollution was evident as well. High proportions of mobile Cd, Cu and Ni also deeper in the sandy soil, closest to the smelter, indicated some downward movement of metals. The hydroxide-bound fraction of Pb dominated in almost all soils and horizons, while Ni, Cr and Zn mostly occurred in mineral structures. Aqua regia extraction is usefully supplemented with sequential extraction, particularly in less polluted soils and in soils that exhibit substantial textural differences within the profiles.     

Heavy metal contamination from mining sites in South Morocco: 1. Use of a biotest to assess metal toxicity of tailings and soils

Our work was conducted to investigate the heavy metal toxicity of tailings and soils collected from five metal mines located in the south of Morocco. We used the MetPAD biotest Kit which detects the toxicity specifically due to the heavy metals in environmental samples. This biotest initially developed to assess the toxicity of aquatic samples was adapted to the heterogeneous physico-chemical conditions of anthropogenic soils. Contrasted industrial soils were collected from four abandoned mines (A, B, C and E) and one mine (D) still active. The toxicity test was run concurrently with chemical analyses on the aqueous extracts of tailings materials and soils in order to assess the potential availability of heavy metals. Soil pH was variable, ranging from very acidic (pH 2.6) to alkaline values (pH 8.0-8.8). The tailings from polymetallic mines (B and D) contained very high concentrations of Zn (38,000-108,000 mg kg(-1)), Pb (20,412-30,100 mg kg(-1)), Cu (2,019-8,635 mg kg(-1)) and Cd (148-228 mg kg(-1)). Water-extractable metal concentrations (i.e., soil extracts) were much lower but were highly toxic as shown by the MetPAD test, except for soils from mines A, E and site C3 from mine C. The soil extracts from mine D were the most toxic amongst all the soils tested. On this site, the toxicity of soil water extracts was mainly due to high concentrations of Zn (785-1,753 mg l(-1)), Cu (1.8-82 mg l(-1)) and Cd (2.0-2.7 mg l(-1)). The general trend observed was an increase in metal toxicity measured by the biotest with increasing available metal contents in tailings materials and soils. Therefore, the MetPAD test can be used as a rapid and sensitive predictive tool to assess the heavy metal availability in soils highly contaminated by mining activities.     

Comparison of solid and liquid-phase bioassays using ecoscores to assess contaminated soils

Bioassays on aqueous and solid phases of contaminated soils were compared, belonging to a wide array of trophic and response levels and using ecoscores for evaluating ecotoxicological and genotoxicological endpoints. The method was applied to four coke factory soils contaminated mainly with PAHs, but also to a lesser extent by heavy metals and cyanides. Aquatic bioassays do not differ from terrestrial bioassays when scaling soils according to toxicity but they are complementary from the viewpoint of ecological relevance. Both aquatic and terrestrial endpoints are strongly correlated with concentrations of 3-ring PAHs. This evaluation procedure allows us to propose a cost-effective battery which embraces a wide array of test organisms and response levels: it includes two rapid bioassays (Microtox(?) and springtail avoidance), a micronucleus test and three bioassays of a longer duration (algal growth, lettuce germination and springtail reproduction). This battery can be recommended for a cost-effective assessment of polluted/remediated soils.     

Terrestrial avoidance behaviour tests as screening tool to assess soil contamination

To assess soil quality and risk assessment, bioassays can be useful tools to gauge the potential toxicity of contaminants focusing on their bioavailable fraction. A rapid and sublethal avoidance behaviour test was used as a screening tool with the earthworm Eisenia andrei and the isopod Porcellionides pruinosus, where organisms were exposed during 48 h to several chemicals (lindane, dimethoate and copper sulphate, for isopods and carbendazim, benomyl, dimethoate and copper sulphate for earthworms). Both species were also exposed to soils from an abandoned mine. For all bioassays a statistical approach was used to derive EC50 values. Isopods and earthworms were able to perceive the presence of toxic compounds and escaping from contaminated to clean soil. Furthermore the behaviour parameter was equally or more sensitive then other sublethal parameters (e.g. reproduction or growth), expressing the advantages of Avoidance Behaviour Tests as screening tools in ERA.     

Glyphosate: environmental contamination,toxicity and potential risks to human health via food contamination

Glyphosate has been the most widely used herbicide during the past three decades. The US Environmental Protection Agency (EPA) classifies glyphosate as ‘practically non-toxic and not an irritant’ under the acute toxicity classification system. This classification is based primarily on toxicity data and due to its unique mode of action via a biochemical pathway that only exists in a small number of organisms that utilise the shikimic acid pathway to produce amino acids, most of which are green plants. This classification is supported by the majority of scientific literature on the toxic effects of glyphosate. However, in 2005, the Food and Agriculture Organisation (FAO) reported that glyphosate and its major metabolite, aminomethylphosphonic acid (AMPA), are of potential toxicological concern, mainly as a result of accumulation of residues in the food chain. The FAO further states that the dietary risk of glyphosate and AMPA is unlikely if the maximum daily intake of 1 mg kg^?1 body weight (bw) is not exceeded. Research has now established that glyphosate can persist in the environment, and therefore, assessments of the health risks associated with glyphosate are more complicated than suggested by acute toxicity data that relate primarily to accidental high-rate exposure. We have used recent literature to assess the possible risks associated with the presence of glyphosate residues in food and the environment.     

Trace element contamination of Norwegian Lake sediments

Concentrations of Sb, Hg, Bi, Cd, Mo, As, Co, Ni, Cr, Cu, V, Pb and Zn in surface and preindustrial sediments from 210 lakes in Norway were used for studying modern atmospheric depositions of these elements. Surface sediments had considerably higher concentrations of Sb, Hg, Bi, Cd, As, Pb than preindustrial sediments. The differences decreased with latitude and altitude. A multivariate analysis including the trace elements and the major constituents (organic matter, Si, Al, Fe and Mn) of surface sediments suggested the following relationships: Sb, Hg, Bi, As, and Pb formed a group with strong associations to organic matter. Ni, Cr and Cu formed a second group, weakly associated to the inorganic sediment fraction (Si and Al). Zn and Cd formed a third group with weak associations to organic matter. Co was associated to Mn, whereas Mo and V showed no important covariations with any other trace elements or major components.     

A modified in-vitro method to assess bioavailable arsenic in pesticide-applied soils

An incubation study was designed to modify the existing in vitro methods to increase the accuracy in estimation of bioavailable arsenic in pesticide-applied soils. In addition to simulating arsenic dissolution in gastric and intestinal solutions, absorbtion by the intestinal membrane was also mimicked using iron-oxide coated filter paper strips inserted in nylon bags. The in vitro experiments were sequentially performed in two phases, namely, the stomach phase and the absorbed-intestinal phase. Arsenic extraction in the in vitro absorbed intestinal phase increased, thereby making it more comparable to the potential in vivo arsenic pool. While animal studies are needed to verify the in vitro results, preliminary data indicate that this modified method may be able to improve site-specific bioavailability predictions in arsenic-contaminated soils.     

Dioxin contamination in soils of Southern Vietnam

Dioxin is the common name for polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs), and is abbreviated as PCDD/Fs. In the case of Southern Vietnam, is of high concern dioxin contamination in the areas affected by past-use chemical defoliants. Our study related to the zone considered as a "hot spot"--Bien Hoa Airbase and surrounding areas (Bien Hung Lake). Although the war ended over 30 years ago, the adverse effects on this territory still continue. Soil and sediment were selected for our research as they act as a sink for PCDD/Fs. The samples were taken and analyzed in CECOTOX laboratory following certified procedures. The total amounts of PCDD/Fs (2,3,7,8 related congeners) in the samples were converted into WHO-TEQ and compared with standard values proposed by Canadian environmental quality guidelines. The obtained data shows a relatively high risk (up to 20.4 times higher than (probable effect level) PEL value for sediment and 46 times higher than standard value for soil). The research is continuing on the assessment of dioxin transport in food chain. Moreover, considering the obtained data a complete solution should be found urgently to solve the problem of dioxin contamination in the studied areas.     

Meta-analysis of environmental contamination by phthalates

Phthalate acid esters (PAE), commonly named phthalates, are toxics classified as endocrine-disrupting compounds; they are primarily used as additives to improve the flexibility in polyvinyl chloride. Many studies have reported the occurrence of phthalates in different environmental matrices; however, none of these studies has yet established a complete overview for those compounds in the water cycle within an urban environment. This review summarizes PAE concentrations for all environmental media throughout the water cycle, from atmosphere to receiving waters. Once the occurrences of compounds have been evaluated for each environmental compartment (urban wastewater, wastewater treatment plants, atmosphere, and the natural environment), we reviewed data in order to identify the fate of PAE in the environment and establish whether geographical and historical trends exist. Indeed, geographical and historical trends appear between Europe and other countries such as USA/Canada and China, however they remain location dependent. This study aimed at identifying both the correlations existing between environmental compartments and the processes influencing the fate and transport of these contaminants into the environment. In Europe, the concentrations measured in waterways today represent the background level of contamination, which provides evidence of a past diffuse pollution. In contrast, an increasing trend has actually been observed for developing countries, especially for China.     

Meta-analysis of environmental contamination by alkylphenols

Alkylphenols and alkylphenol ethoxylates (APE) are toxics classified as endocrine-disrupting compounds; they are used in detergents, paints, herbicides, pesticides, emulsifiers, wetting and dispersing agents, antistatic agents, demulsifiers, and solubilizers. Many studies have reported the occurrence of alkylphenols in different environmental matrices, though none of these studies have yet to establish a comprehensive overview of such compounds in the water cycle within an urban environment. This review summarizes APE concentrations for all environmental media throughout the water cycle, from the atmosphere to receiving waters. Once the occurrence of compounds has been assessed for each environmental compartment (urban wastewater, wastewater treatment plants [WWTP], atmosphere, and the natural environment), data are examined in order to understand the fate of APE in the environment and establish their geographical and historical trends. From this database, it is clear that the environment in Europe is much more contaminated by APE compared to North America and developing countries, although these APE levels have been decreasing in the last decade. APE concentrations in the WWTP effluent of developed countries have decreased by a factor of 100 over the past 30?years. This study is aimed at identifying both the correlations existing between environmental compartments and the processes that influence the fate and transport of these contaminants in the environment. In industrial countries, the concentrations observed in waterways now represent the background level of contamination, which provides evidence of a past diffuse pollution in these countries, whereas sediment analyses conducted in developing countries show an increase in APE content over the last several years. Finally, similar trends have been observed in samples drawn from Europe and North America.     

A multibiomarker approach using the polychaete Arenicola marina to assess oil-contaminated sediments

Background, aim and scope  

Marine and coastal sediments can accumulate substantial concentrations of metals and hydrocarbons, yet the consequences of this contamination for exposed biota in situ can be difficult to establish. Here, we examine the hypothesis that exposure to contaminated sediments can lead to detrimental effects in sediment-dwelling species. The combination of chemical and biological assessment allows the identification of the impact of chemical contamination, and their use as assessment tools is becoming increasingly important.     

Cesium-137 and mercury contamination in lake sediments.

The contribution of fluvial discharge and global fallout of 137Cs and mercury to sedimentation fluxes in Lake Shinji and Lake Nakaumi, Japan, was studied. The fluvial flux through soil erosion accounted for 11 to 27% of accumulated 137Cs in the sediments in the 1950's and 1960's, which were the periods of the most extensive atmospheric input, and for 90 to 100% in the 1990's. The vertical profiles of mercury concentrations in the lake sediments studied showed a maximum between 1959 and 1963, which was originated mostly from the extensive use of mercury-agrochemicals in paddyfields of the watershed in the past. These findings are representative examples of long-term contamination of lake sediments caused by the contaminated ground soil erosion.     

Peat soils as a source of lead contamination to upland fluvial systems

Upland peat soils are generally regarded as effective sinks of atmospherically deposited lead. However, the physical process of erosion has the potential to transform peat soils from sinks to sources of lead contamination. Lead input and fluvial lead outputs (dissolved+particulate) were estimated for a contaminated and severely eroding peatland catchment in the southern Pennines, UK. Lead input to the catchment is 30.0+/-6.0gha(-1)a(-1) and the output from the catchment is 317+/-22.4gha(-1)a(-1). Suspended particulate matter accounts for 85% of lead export. Contaminated peat soils of the catchment are a significant source of lead to the fluvial system. This study has demonstrated strong coupling between the physical process of erosion and the mobilization of lead into the fluvial system. The process of peat erosion should therefore be considered when estimating lead outputs from peatland catchments, especially in the context of climate change.     

Optimization of an effective extraction procedure for the analysis of microcystins in soils and lake sediments

Microcystin analysis in sediments and soils is considered very difficult due to low recovery for extraction. This is the primary limiting factor for understanding the fate of toxins in the interface between water and sediment in both the aquatic ecosystem as well as in soils. In the present study, a wide range of extraction solvents were evaluated over a wide range of pH, extraction approaches and equilibration time to optimize an effective extraction procedure for the analysis of microcystins in soils and lake sediments. The number of extractions required and acids in extraction solutions were also studied. In this procedure, EDTA-sodium pyrophosphate solution was selected as an extraction solvent based on the adsorption mechanism study. The optimized procedure proved to be highly efficient and achieved over 90% recovery. Finally, the developed procedure was applied to field soil and sediment sample collected from Chinese lakes during bloom seasons and microcystins were determined in six of ten samples.     

Comparison of selected non-exhaustive extraction techniques to assess PAH availability in dissimilar soils

Recently, it has become apparent that the use of total contaminant concentrations as a measure of potential contaminant exposure to plants or soil organisms is inappropriate and that bioavailability of contaminants is a better measure of potential exposure. In light of this, non-exhaustive extraction techniques are being investigated to assess their appropriateness in determining bioavailability. In this study, phenanthrene extractability using hydroxypropyl-beta-cyclodextrin (HPCD) and desorption kinetics using butan-1-ol (BuOH) were determined in three dissimilar spiked soils. The soils were extracted after 1 d, 40 d and 80 d of soil-compound contact time. The amount of phenanthrene extracted by HPCD was compared to the rapidly desorbed fraction removed by BuOH. Further experiments using the same soils and extraction methods to assess the relative extractability of phenanthrene, pyrene and benzo(a)pyrene were conducted. Overall, the extraction methods used in this study had different extraction efficiencies. Results suggest that as compound hydrophobicity increased, BuOH became a more exhaustive extractant with respect to HPCD, especially for soils with high clay and organic matter content. These results are important as they highlight differences between two contrasting non-exhaustive extraction techniques both of which have been suggested to be appropriate in the assessment of bioavailability.     

Using sequential indicator simulation to assess the uncertainty of delineating heavy-metal contaminated soils

Mapping the spatial distribution of soil pollutants is essential for delineating contaminated areas. Currently, geostatistical interpolation, kriging, is increasingly used to estimate pollutant concentrations in soils. The kriging-based approach, indicator kriging (IK), may be used to model the uncertainty of mapping. However, a smoothing effect is usually produced when using kriging in pollutant mapping. The detailed spatial patterns of pollutants could, therefore, be lost. The local uncertainty of mapping pollutants derived by the IK technique is referred to as the conditional cumulative distribution function (ccdf) for one specific location (i.e. single-location uncertainty). The local uncertainty information obtained by IK is not sufficient as the uncertainty of mapping at several locations simultaneously (i.e. multi-location uncertainty or spatial uncertainty) is required to assess the reliability of the delineation of contaminated areas. The simulation approach, sequential indicator simulation (SIS), which has the ability to model not only single, but also multi-location uncertainties, was used, in this study, to assess the uncertainty of the delineation of heavy metal contaminated soils. To illustrate this, a data set of Cu concentrations in soil from Taiwan was used. The results show that contour maps of Cu concentrations generated by the SIS realizations exhausted all the spatial patterns of Cu concentrations without the smoothing effect found when using the kriging method. Based on the SIS realizations, the local uncertainty of Cu concentrations at a specific location of x', refers to the probability of the Cu concentration z(x') being higher than the defined threshold level of contamination (z(c)). This can be written as Prob(SIS)[z(x')>z(c)], representing the probability of contamination. The probability map of Prob(SIS)[z(x')>z(c)] can then be used for delineating contaminated areas. In addition, the multi-location uncertainty of an area A,delineated as contaminated based on the probability map of Prob(SIS)[z(x')>z(c)], can be calculated to assess the reliability of delineation. Multi-location uncertainty refers to the probability of Cu concentrations in several locations, x'(1), x'(2), em leader, x'(m,) in the area A, being higher than the threshold (z(c)) as denoted by Prob(SIS)[z(x'(1))>z(c), z(x'(2))>z(c), em leader, andz(x'(m))>z(c)] or Prob(SIS)[z(A)>z(c)]. The multi-location uncertainty Prob(SIS)[z(A)>z(c)], obtained from the SIS, can be used to assess the reliability of delineation for regions suspected of contamination, (A), which has been delineated as contaminated. Reliance on this information facilitates the decision making process in determining which areas are contaminated and require cleanup action.     

Extraction of arsenate and arsenite species from soils and sediments

The primary objective of this study was to develop a simple method that can be used to extract the more readily mobilizable and bioavailable arsenic species from soil and sediment while at the same time minimizing the transformation between (AsIII) and (AsV), the two most commonly found arsenic species in the environment. Several extraction strategies were evaluated using phosphate as extractant in combination with either ethylenediaminetetraacetic acid (EDTA), hydroxylamine hydrochloride (NH2OH.HCl), or sodium diethyldithiocarbamate trihydrate (NaDDC). The addition of EDTA in the phosphate solution did not prevent AsIII from oxidation. While promising results were shown when 1% NH2OH.HCl was added, conversion of AsIII began to occur with extended extraction time (> 12 h). Good results were achieved using 10 mM phosphate and 0.5% NaDDC where AsIII oxidation was clearly minimized. The combined phosphate and NaDDC solution was applied to several soil and sediment samples. AsIII spiked was quantitatively recovered in all soil types tested.