Reductive dechlorination of chlorinated methanes in cement slurries containing Fe(II)

Degradative solidification/stabilization (DS/S) is a novel remediation technology that combines chemical degradation with conventional solidification/stabilization. The applicability of the Fe(II)-based DS/S to treating chlorinated alkanes was tested by characterizing degradation reactions of carbon tetrachloride (CT) and its daughter products in cement slurries containing Fe(II). Degradation kinetics of CT and chloroform (CF) were generally very rapid with reaction rates comparable to rates that can be obtained with zero-valent iron. Dechlorination reactions of CT proceeded primarily via a hydrogenolysis pathway, which yielded CF and methylene chloride (MC) as major products and chloromethane and methane as minor products. However, reaction pathways other than hydrogenolysis also appeared to be important at very high pH conditions. MC apparently was resistant to dechlorination reactions over a period of about two months. Kinetics of CT and CF transformation were strongly dependent on pH with an optimal value around 13, which was higher than found previously for PCE. When the initial CF concentration varied between 0.01 and 1 mM, and the Fe(II) dose was 104 mM, pseudo-first-order kinetics generally described the degradation reactions of CF. However, there was also some indication of substrate saturation kinetics in these experiments. This suggests that a saturation model would better describe the kinetics in systems with higher concentration of substrates or lower concentration of the reactive surfaces.     

Batch-test study on the dechlorination of 1,1,1-trichloroethane in contaminated aquifer material by zero-valent iron

Chlorinated aliphatic hydrocarbons are common groundwater contaminants. One possible remediation option is in-situ reductive dechlorination by zero-valent iron, either by direct injection or as reactive barriers. Chlorinated ethenes (tetrachloroethene: PCE; trichloroethene: TCE) have received extensive attention in this context. However, another common groundwater pollutant, 1,1,1-trichlorethane (TCA), has attracted much less attention. We studied TCA reduction by three types of granular zero-valent irons in a series of batch experiments using polluted groundwater, with and without added aquifer material. Two types of iron were able to reduce TCA completely with no daughter product concentration increases (1,1-dichloroethane: DCA; chloroethane: CA). One type of iron showed slower reduction, with intermediate rise of DCA and CA concentrations. When evaluating the formation of daughter products, the tests on the groundwater alone showed different results than the groundwater plus aquifer batches: DCA did not temporarily accumulate in the batches with added aquifer material, contrary to the batches without added aquifer material. 1,1-dichloroethene (DCE, also present in the groundwater as an abiotic degradation product of TCA) was also reduced slower in the batches without added aquifer material than in the batches with aquifer material. Redox potentials gradually decreased to low values in batches with aquifer material without iron, while the batches with groundwater alone maintained a constant higher redox potential. Either adsorption processes or microbiological activity in the samples could explain these phenomena. Polymerase Chain Reaction (PCR: a targeted gene probe technique) for chlorinated aliphatic compound (CAH)-degrading bacteria confirmed the presence of Dehalococcoides sp. (chloroethene-degraders) but was negative for Desulfobacterium autotrophicum (a known co-metabolic TCA degrader). DCA reduction was rate determining: first-order half-lives of 300-350 h were observed. TCA was fully removed within hours. CA is resistant to reduction by zero-valent iron but it is known to hydrolyze easily. Since CA did not accumulate in our batches, it may have disappeared by the latter mechanism or it may not have formed as a major daughter product.     

The reductive degradation of 1,1,1-trichloroethane by Fe(0) in a soil slurry system

Most studies on the treatment of chlorinated contaminants by Fe(0) focus on aqueous system tests. However, few is known about the effectiveness of these tests for degrading chlorinated contaminants such as 1,1,1-trichloroethane (TCA) in soil. In this work, the reductive degradation performance of 1,1,1-TCA by Fe(0) was thoroughly investigated in a soil slurry system. The effects of various factors including acid-washed iron, the initial 1,1,1-TCA concentration, Fe(0) dosage, slurry pH, and common constituents in groundwater and soil such as Cl^?, HCO₃ ^?, SO₄ ^2?, and NO₃ ^? anions and humic acid (HA) were evaluated. The experimental results showed that 1,1,1-TCA could be effectively degraded in 12 h for an initial Fe(0) dosage of 10 g L^?1 and a soil/water mass ratio of 1:5. The soil slurry experiments showed two-stage degradation kinetics: a slow reaction in the first stage and a fast reductive degradation of 1,1,1-TCA in the second stage. The reductive degradation of 1,1,1-TCA was expedited as the mass concentration of Fe(0) increased. In addition, high pHs adversely affected the degradation of 1,1,1-TCA over a pH range of 5.4–8.0 and the reductive degradation efficiency decreased with increasing slurry pH. The initial 1,1,1-TCA concentration and the presence of Cl^? and SO₄ ^2? anions had negligible effects. HCO₃ ^? anions had a accelerative effect on 1,1,1-TCA removal, and both NO₃ ^? and HA had inhibitory effects. A Cl^? mass balance showed that the amount of Cl^? ions released into the soil slurry system during the 1,1,1-TCA degradation increased with increasing reaction time, suggesting that the main degradation mechanism of 1,1,1-TCA by Fe(0) in a soil slurry system was reductive dechlorination with 1,1-DCA as the main intermediate. In conclusion, this study provides a theoretical basis for the practical application of the remediation of contaminated sites containing chlorinated solvent.     

The production and release to the atmosphere of 1,1,1-trichloroethane (methyl chloroform)

The results of an audited survey of production and use for methyl chloroform (1,1,1-trichloroethane) for the years 1970–1988 are presented.     

Effects of anions on the kinetics and reactivity of nanoscale Pd/Fe in trichlorobenzene dechlorination

Influences of anionic co-solutes on dechlorination of 1,2,4-trichlorobenzene (124TCB) by the nanoscale Pd/Fe particles were investigated in batch experiments in the presence of an anionic solute such as nitrate, nitrite, perchlorate, phosphate, carbonate, silica, sulfate, sulfite, or sulfide. Based on the extent of inhibitory effects on the 124TCB dechlorination, the anions can be ranked in the order of: control≈sulfate≈silica相似文献   

Comparison of hematite/Fe(II) systems with cement/Fe(II) systems in reductively dechlorinating trichloroethylene

Reactive reductants of cement/Fe(II) systems in dechlorinating chlorinated hydrocarbons are unknown. This study initially evaluated reactivities of potential reactive agents of cement/Fe(II) systems such as hematite (alpha-Fe(2)O(3)), goethite (alpha-FeOOH), lepidocrocite (gamma-FeOOH), akaganeite (beta-FeOOH), ettringite (Ca(6)Al(2)(SO(4))(3)(OH)(12)), Friedel's salt (Ca(4)Al(2)Cl(2)(OH)(12)), and hydrocalumite (Ca(2)Al(OH)(6)(OH).3H(2)O) in reductively dechlorinating trichloroethylene (TCE) in the presence of Fe(II). It was found that a hematite/Fe(II) system shows TCE degradation characteristics similar to those of cement/Fe(II) systems in terms of degradation kinetics, Fe(II) dose dependence, and final products distribution. It was therefore suspected that Fe(III)-containing phases of cement hydrates in cement/Fe(II) systems behaved similarly to the hematite. CaO, which was initially introduced as a pH buffer, was observed to participate in or catalyze the formation of reactive reductants in the hematite/Fe(II) system, because its addition enhanced the reactivities of hematite/Fe(II) systems. From the SEM (scanning electron microscope) and XRD (X-ray diffraction) analyses that were carried out on the solids from hematite/Fe(II) suspensions, it was discovered that a sulfate green rust with a hexagonal-plate structure was probably a reactive reductant for TCE. However, SEM analyses conducted on a cement/Fe(II) system showed that hexagonal-plate crystals, which were presumed to be sulfate green rusts, were much less abundant in the cement/Fe(II) than in the hematite/Fe(II) systems. It was not possible to identify any crystalline minerals in the cement/Fe(II) system by using XRD analysis, probably because of the complexity of the cement hydrates. These observations suggest that major reactive reductants of cement/Fe(II) systems may differ from those of hematite/Fe(II) systems.     

Catalytic dechlorination of monochlorobenzene with a new type of nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant

A unique type of nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant was prepared and used for dechlorination of monochlorobenzene (MCB). The sample Ni(B)/Fe(B) was synthesized by an electroless plating method, in which nanoscale Ni(B) was deposited on the surface of nanoscale Fe(B) synthesized by chemical reduction. The results suggest that the nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant has higher dechlorination efficiency than Ni/Fe(B) catalytic reductant prepared by replacing Fe(B) with Ni(2+) in aqueous solution. The Ni content was found to be an important factor in catalytic dechlorination, with the dechlorination rate increasing with Ni content. The electroless plating method improve the efficiency of the Ni(2+) in the solution. Dechlorination takes place with the existence of nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant via a pseudo-first-order reaction.     

Kinetics of oxidation of chlorobenzenes and phenyl-ureas by Fe(II)/H2O2 and Fe(III)/H2O2. Evidence of reduction and oxidation reactions of intermediates by Fe(II) or Fe(III)

The rates of degradation of 1,2,4-trichlorobenzene (TCB), 2,5-dichloronitrobenzene (DCNB), diuron and isoproturon by Fe(II)/H2O2 and Fe(III)/H2O2 have been investigated in dilute aqueous solution ([Organic compound]0 approximately 1 microM, at 25.0 +/- 0.2 degrees C and pH < or = 3). Using the relative rate method with atrazine as the reference compound, and the Fe(II)/H2O2 (with an excess of Fe(II)) and Fe(III)/H2O2 systems as sources of OH radicals, the rate constants for the reaction of OH* with TCB and DCNB were determined as (6.0 +/- 0.3)10(9) and (1.1 +/- 0.2)10(9) M(-1) s(-1). Relative rates of degradation of diuron and isoproturon by Fe(II)/H2O2 were about two times smaller in the absence of dissolved oxygen than in the presence of oxygen. These data indicate that radical intermediates are reduced back to the parent compound by Fe(II) in the absence of oxygen. Oxidation experiments with Fe(III)/H2O2 showed that the rate of decomposition of atrazine markedly increased in the presence of TCB and this increase has been attributed to a regeneration of Fe(II) by oxidation reactions of intermediates (radical species and dihydroxybenzenes) by Fe(III).     

Reduction of Ag(I), Au(III), Cu(II), and Hg(II) by Fe(II)/Fe(III) hydroxysulfate green rust

Green rusts are mixed Fe(II)/Fe(III) hydroxides that are found in many suboxic environments where they are believed to play a central role in the biogeochemical cycling of iron. X-ray absorption fine structure analysis of hydroxysulfate green rust suspensions spiked with aqueous solutions of AgCH(3)COO, AuCl(n)(OH)(4-n), CuCl(2), or HgCl(2) showed that Ag(I), Au(III), Cu(II), and Hg(II) were readily reduced to Ag(0), Au(0), Cu(0), and Hg(0). Imaging of the resulting solids from the Ag(I)-, Au(III)-, and Cu(II)-amended green rust suspensions by transmission electron microscopy indicated the formation of submicron-sized particles of Ag(0), Au(0), and Cu(0). The facile reduction of Ag(I), Au(III), Cu(II), and Hg(II) to Ag(0), Au(0), Cu(0), and Hg(0), respectively, by green rust suggests that the presence of green rusts in suboxic soils and sediments can have a significant impact on the biogeochemistry of silver, gold, copper, and mercury, particularly with respect to their mobility.     

Influence of pH,EDTA/Fe(II) ratio,and microbial culture on Fe(II)-mediated autotrophic denitrification

Environmental Science and Pollution Research - Fe(II)-mediated autotrophic denitrification with four different microbial cultures under different pH and EDTA/Fe(II) conditions was investigated in...     

Dechlorination of trichloroethylene formed from 1,1,2,2-tetrachloroethane by dehydrochlorination in Portland cement slurry including Fe(II)

Transformation of 1,1,2,2-tetrachloroethane (1,1,2,2-TeCA) by Fe(II) in 10% cement slurries was characterized using a batch reactor system. 1,1,2,2-TeCA was completely converted to trichloroethylene (TCE) within 1h in all experiments, even in controls with cement that did not include Fe(II). Therefore, complete degradation of 1,1,2,2-TeCA depends on the behavior of TCE. The half-life of TCE was observed to be 15d when concentrations of Fe(II) and 1,1,2,2-TeCA were 98mM and 0.245mM, respectively. The kinetics of TCE removal was observed to be dependent on Fe(II) dose, pH and initial substrate concentration. Pseudo-first-order rate constants linearly increased with Fe(II) dose up to 198mM when initial target concentration was 0.245mM. Pseudo-first-order kinetics generally described the degradation reactions of TCE at a specific initial concentration, but a modified Langmuir-Hinshelwood model was necessary to describe the degradation kinetics of TCE over a wide range of initial concentrations. A surface reaction of TCE on active solids, which were formed from Fe(II) and products of cement hydration appears to control observed TCE degradation kinetics.     

Degradation of polychlorinated dibenzo-p-dioxins in aqueous solution by Fe(II)/H2O2/UV system

The photodegradation of polychlorinated dibenzo-p-dioxins (PCDDs), which include tetra- to octa-CDDs (TeCDD, PeCDD, HxCDD, HpCDD and OCDD), was carried out in the presence of Fe(II) and H2O2 mixed reagent. The degradation efficiency was strongly influenced by UV irradiation, and the initial concentrations of H2O2 and Fe(II). An initial TeCDD concentration of 10 ng l(-1) was completely degraded within 20 min under the optimum conditions. All PCDDs tested were successfully degraded by Fe(II)/H2O2/UV treatment and complete degradation of TeCDD, PeCDD and HxCDD was achieved within 120 min. PCDD photodegradation rates decreased with the number of chlorine atoms. The degradation process of TeCDD by this system seems to be initiated by an oxidative reaction (OH* radical attack) because less chlorinated DDs as intermediate products were not detected. From the Frontier electron density calculation, the first OH* radical attack positions on TeCDD were found to be four C atoms neighboring two O atoms. The decomposition of TeCDD gave 4,5-dichlorocatechol as an intermediate product. A TeCDD degradation scheme was proposed based on the identified intermediate and the values of Frontier electron density. Based on these results, Fe(II)/H2O2/UV system could be useful technology for the treatment of wastewater containing persistent pollutants such as dioxins and polychlorinated biphenyls.     

Effects of various ions on the dechlorination kinetics of hexachlorobenzene by nanoscale zero-valent iron

The effect of several anions and cations normally co-present in soil and groundwater contamination sites on the degradation kinetics and removal efficiency of hexachlorobenzene (HCB) by nanoscale zero-valent iron (NZVI) particles was examined. The degradation kinetics was not influenced by the HCO(3)(-), Mg(2+), and Na(+) ions. It was enhanced in the presence of the Cl(-) and SO(4)(2-) ions due to their corrosion promotion. The NO(3)(-) competes with HCB so it inhibits the degradation reaction. The Fe(2+) ions would inhibit the degradation reaction due to passivation layer formed, while it was enhanced in the presence of Cu(2+) ions resulted from the reduced form of copper on NZVI surfaces. These observations lead to a better understanding of HCB dechlorination with NZVI particles and can facilitate the remediation design and prediction of treatment efficiency of HCB at remediation sites.     

Comparative study of the oxidation of atrazine and acetone by H2O2/UV, Fe(III)/UV, Fe(iii)/H2O2/UV and Fe(II) or Fe(III)/H2O2

In this study, the rates of degradation of organic compounds by several AOPs (H₂O₂/UV, Fe(III)/UV, Fe(III)/H₂O₂/UV, Fe(II)/H₂O₂ and Fe(III)/H₂O₂) have been compared. Experiments were carried out at pH ≈ 3 (perchloric acid / sodium perchlorate solutions) and with UV reactors equipped with a low-pressure mercury vapour lamp (emission at 253.7 run). The data obtained with atrazine ([Atrazine]_o = 100 μg/L) showed that the rate of degradation of atrazine in very dilute aqueous solution is much more rapid with Fe(III)/UV than with H₂O₂/UV. Photo-Fenton process (Fe(III)/H₂O₂/UV) was found to be more efficient than H₂O₂/UV and Fe(II)/H₂O₂ for the mineralization of acetone ([Acetone]_o = 1 mM).     

A comparative study of the effects of chloride, sulfate and nitrate ions on the rates of decomposition of H2O2 and organic compounds by Fe(II)/H2O2 and Fe(III)/H2O2

The effects of chloride, nitrate, perchlorate and sulfate ions on the rates of the decomposition of hydrogen peroxide and the oxidation of organic compounds by the Fenton's process have been investigated. Experiments were conducted in a batch reactor, in the dark at pH < or = 3.0 and at 25 degrees C. Data obtained from Fe(II)/H2O2 experiments with [Fe(II)]0/[H2O2]0 > or = 2 mol mol(-1), showed that the rates of reaction between Fe(II) and H2O2 followed the order SO4(2-) > ClO4(-) = NO3- = Cl-. For the Fe(III)/H2O2 process, identical rates were obtained in the presence of nitrate and perchlorate, whereas the presence of sulfate or chloride markedly decreased the rates of decomposition of H2O2 by Fe(III) and the rates of oxidation of atrazine ([atrazine]0 = 0.83 microM), 4-nitrophenol ([4-NP]0 = 1 mM) and acetic acid ([acetic acid]0 = 2 mM). These inhibitory effects have been attributed to a decrease of the rate of generation of hydroxyl radicals resulting from the formation of Fe(III) complexes and the formation of less reactive (SO4(*-)) or much less reactive (Cl2(*-)) inorganic radicals.     

Montmorillonite-Cu(II)/Fe(III) oxides magnetic material as adsorbent for removal of humic acid and its thermal regeneration

In this work, the adsorption features of montmorillonite and the magnetic properties of Cu(II)/Fe(III) oxides were combined in a material to produce magnetic adsorbent, which can be separated from the medium by a simple magnetic process after adsorption. The magnetic material is effective for the removal of humic acid. At pH 6.1, 96% removal was observed from 4.4 mg l(-1) humic acid solution containing 0.02 M NaCl. The adsorption is pH and ionic strength dependent. Adsorption is favored at lower pH values and dissolved NaCl can enhance the adsorption. The adsorption mechanism of humic acid to the magnetic material was suggested to be the ligand exchange reaction between carboxylic groups of humic acid molecules and the magnetic material surface. The magnetic material can be thermally regenerated. The temperature and time required to achieve good regeneration efficiency were determined to be 300 degrees C and 3 h, respectively. The regenerated adsorbent is still magnetic and approximately has as high specific saturation magnetization and good adsorption capacities as the as-prepared adsorbent.     

Reductive dechlorination of 1,2,4-trichlorobenzene with palladized nanoscale Fe(zero-valent) particles supported on chitosan and silica

In this study, nanoscale Pd-Fe particles, with diameters less than 100 nm, were synthesized and dispersed over the chitosan and silica supports. Three different Pd-Fe particles were synthesized, namely 0.1% Pd-Fe, 0.5% Pd-Fe and 1.0% Pd-Fe. SEM images confirmed that the Pd-Fe particles were dispersed over the surface of the supports while SEM-EDX confirmed evenly distribution of Pd over Fe(zero-valent). alpha-Fe(zero-valent) crystallites were identified by means of XRD and observed in TEM. Reductive dechlorinations of 1,2,4-trichlorobenzene (1,2,4-TCB) with the nanoscale Pd-Fe/chitosan and Pd-Fe/silica were carried out in the batch experiment system. Disappearance of the parent species and formation of the reaction intermediates and end product were monitored at discrete times. The results show that the nano-scale Pd-Fe particles were able to completely dechlorinate the chlorinated benzenes within a very short timescale. Complete dechlorinations of 1,2,4-TCB to benzene were achieved within 60 min with the 1.0% Pd-Fe/chitosan and within 100 min with the 1.0% Pd-Fe/silica. Reaction rates were observed to increase with increasing Pd content of the Pd-Fe/support. The reactions apparently followed pseudo-first-order kinetics with respect to the 1,2,4-TCB transformation. A kinetic model is constructed to fit the experimental results for the reactions, enabling identification of the major and minor dechlorination pathways of 1,2,4-TCB. The model suggests that the 1,2,4-TCB transformation mainly followed the primary pathway of direct reductive dechlorination to benzene and secondary pathway of sequential hydrogenolysis to 1,2-dichlorobenzene (1,2-DCB) and then chlorobenzene (CB) or benzene.     

Simultaneous oxidation of EDTA and reduction of metal ions in mixed Cu(II)/Fe(III)-EDTA system by TiO2 photocatalysis

Both the photooxidation of EDTA and the photoreduction of metal ions in metal-EDTA systems were investigated. EDTA oxidation by TiO(2) photocatalysis occurred sequentially as Cu(II)-EDTA>Cu(II)/Fe(III)-EDTA>Fe(III)-EDTA. For Cu(II)-EDTA, EDTA was completely decomposed after only 60min of irradiation. The rate of EDTA decomposition was directly correlated with the initial Cu(II) concentration in the case of a mixed Cu(II)/Fe(III)-EDTA system. The metal ions in a single metal-EDTA complex were removed following significant decomposition of EDTA. For a mixed Cu(II)/Fe(III)-EDTA system, however, no copper was removed whereas almost all of the iron was removed. The iron and copper species deposited on the TiO(2) surface were identified via EPR and XPS as mixed FeO/Fe(3)O(4) and Cu(0)/Cu(2)O, respectively.     

微波活化对Ca(OH)2孔隙结构及脱氯性能的影响

采用微波炉对一定质量的氢氧化钙样品进行活化,利用压汞仪考察了不同微波活化时间及脱氯反应前后的Ca(OH)2总比孔表面积、分段比表面积和孔径分布的变化,并在脱氯实验台上对脱氯效率进行实际测试。结果表明,微波活化存在一个最佳时间,在此时间内样品比孔表面积增大50%左右,而超过这一时间样品比表面积回复性减小;微波活化主要通过增加3～20 nm孔径段的微孔为样品提供更大比表面积;这些新增加的微孔在脱氯反应过程中被完全利用或消耗; 最佳活化时间下的微波活化使Ca(OH)2在较低Ca/Cl摩尔比下获得更大脱氯效率,Ca/Cl摩尔比=4.1时,脱氯效率增加了20%。     

Sonolysis of alkylphenols in aqueous solution with Fe(II) and Fe(III)

The sonolytic degradation of alkylphenols (APs), such as butylphenol, pentylphenol, octylphenol, and nonylphenol (NP), in water was investigated at a sound frequency of 200 kHz with an acoustic intensity of 6 W cm(-2) under argon, oxygen, and air atmospheres. The sonolytic degradation rate of the APs under the conditions of the present study depended upon their alkyl chain length. The decrease in the degradation rate by the radical scavenging effect was in the range of about 48-82% for APs in the presence of 3 mM 2-methyl-2-propanol. The free radicals play a significant role in the sonolytic degradation process of the APs. In the presence of Fe(II) and Fe(III), the pseudo-first-order rate constants for the sonolytic degradation of 30 microM NP as a function of the concentration of Fe(II) and Fe(III) were estimated under argon and oxygen. The maximum rate constants were observed at 50 microM Fe(II) (0.139 +/- 0.008 min(-1)) and 100 microM Fe(III) (0.103 +/- 0.001 min(-1)) under oxygen. The total organic carbon concentration (TOC) was investigated under same conditions. TOC decreased in the range of about 50-70% during the sonication in the presence of Fe(II) and Fe(III) under argon and oxygen. The sonochemical effects by the addition of Fe(II) and Fe(III) as catalyst during the sonication under the proper atmosphere result in a remarkable enhancement of degradation and mineralization.