Thioarsenate formation upon dissolution of orpiment and arsenopyrite

Thioarsenates were previously determined as dominant species in geothermal and mineral waters with excess sulfide. Here, we used batch leaching experiments to determine their formation upon weathering or industrial leaching of the arsenic-sulfide minerals orpiment (As₂S₃) and arsenopyrite (FeAsS) under different pH and oxygen conditions. Under acidic conditions, as expected based on their known kinetic instability at low pH, no thioarsenates formed in either of the two mineral systems. Under neutral to alkaline conditions, orpiment dissolution yielded mono-, di- and trithioarsenate which accounted for up to 43–55% of total arsenic. Thioarsenate formation upon arsenopyrite dissolution was low at neutral (4%) but significant at alkaline pH, especially under suboxic to sulfidic conditions (20–43%, mainly as monothioarsenate). In contrast to orpiment, we postulate that recombination of arsenite and sulfide in solution is of minor importance for monothioarsenate formation during alkaline arsenopyrite dissolution. We propose instead that hydroxyl physisorption lead to formation of As-OH-S surface complexes by transposition of hydroxyl anions to arsenic or iron sites. Concurrently formed ironhydroxides could provide re-sorption sites for the freshly released monothioarsenate. However, sorption experiments with goethite showed slower sorption kinetics of monothioarsenate compared to arsenite, but comparable with arsenate. The discovery that thioarsenates are released by natural weathering and industrial leaching processes and that, once they are released, have a higher mobility than the commonly-investigated species arsenite and arsenate requires future studies to consider them when assessing arsenic release in sulfidic natural or mining-impacted environments.     

电解锰渣中锰的浸出条件及特征

采用水洗-酸解法回收电解锰渣中锰,探讨了清水量、酸量以及温度在不同阶段对锰浸(洗)出条件的影响,分析了回收锰的主要因素及浸出特征。实验结果表明,50 g电解锰渣经m渣∶m水=1∶10的清水水洗后,采用10%的硫酸在70℃的水浴温度下酸解2 h,Mn2+浸出量为1.673 g,回收率达到97.3%,而温度和酸度对锰离子的浸出影响明显,酸度调控可有效分离酸浸锰液中金属成分,为减少电解锰渣环境污染的同时,实现电解锰渣资源化利用。     

O3、H2O2/O3及UV/O3在焦化废水深度处理中的应用

采用O₃、H₂O₂/O₃和UV/O₃等高级氧化技术(AOPs)对某焦化公司的生化出水进行深度处理,考察了O₃与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响,确定出O₃氧化反应的最佳工艺参数为：接触时间40 min,溶液pH 8.5,反应温度25℃,此条件下废水COD及UV₂₅₄的去除率最高可达47.14%和73.47%;H₂O₂/O₃及UV/O₃两种组合工艺对焦化废水COD及UV₂₅₄的去除率均有一定程度的提高,但H₂O₂/O₃系统的运行效果取决于H₂O₂的投加量。研究结论表明,单纯采用COD作为评价指标,并不能准确反映出O₃系列AOPs对焦化废水中有机污染物的降解作用。     

含锰废渣的氧化-活化再生回用工艺

为实现紫苏醛生产过程中二氧化锰（氧化剂）的循环利用,采用一种新型的氧化-活化工艺再生得到活性二氧化锰,即以紫苏醇合成紫苏醛过程中产生的含锰废渣为原料,首先采用氯酸钠氧化含锰废渣得到初级二氧化锰,然后使用高锰酸钾对初级二氧化锰进一步活化得到活性二氧化锰。实验表明,制取初级二氧化锰的最佳工艺条件为：反应时间为4h,反应温度为90～95℃,硫酸摩尔浓度为1.5 mol/L,氯酸钠加量为理论量的130%。制取活性二氧化锰的合适条件为：反应温度在60℃时,反应时间为1.5 h;反应温度在50℃时,反应时间为2.5 h。采用氧化-活化法再生的活性二氧化锰氧化紫苏醇,紫苏醛的产率可达52.8%,与使用电解二氧化锰氧化得到的紫苏醛的产率53.1%相当,而使用初级二氧化锰,紫苏醛的产率仅为14.9%。     

Fate of citalopram during water treatment with O3, ClO2, UV and Fenton oxidation

In the present study we investigate the fate of citalopram (CIT) at neutral pH using advanced water treatment technologies that include O₃, ClO₂ oxidation, UV irradiation and Fenton oxidation. The ozonation resulted in 80% reduction after 30 min treatment. Oxidation with ClO₂ removed >90% CIT at a dosage of 0.1 mg L⁻¹. During UV irradiation 85% reduction was achieved after 5 min, while Fenton with addition of 14 mg L⁻¹ (Fe²⁺) resulted in 90% reduction of CIT. During these treatment experiments transformation products (TPs) were formed from CIT, where five compounds were identified by using high resolution and tandem mass spectrometry. Among these desmethyl-citalopram and citalopram N-oxide have been previously identified as human metabolites, while three are novel and published here for the first time. The three TPs are a hydroxylated dimethylamino-side chain derivative, a butyrolactone derivative and a defluorinated derivative of CIT.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

用H2O2/Fe3+处理高浓度含甲醛废水的研究

研究采用H₂O₂/Fe³⁺催化氧化处理高浓度含甲醛废水,探讨了双氧水和催化剂投加量、反应pH及反应温度等操作条件对处理效果的影响,并通过酸溶解回用失活催化剂。结果表明,较优的操作条件为：H₂O₂/COD（质量比）=2.2～2.6,Fe³⁺/H₂O₂（摩尔比）=0.048～0.058,反应pH 1.80～2.68,反应温度50℃,反应时间40 min;在上述操作条件下,甲醛去除率达到99%以上,COD去除率达到85%以上。失活的催化剂可通过稀酸溶解后循环使用,其效果与三价铁盐作催化剂的基本相同。采用H₂O₂/Fe³⁺处理含甲醛废水具有比采用H₂O₂/Fe³⁺较优的效果。     

Modelling photochemical oxidant formation, transport, deposition and exposure of terrestrial ecosystems

The chemical processes responsible for production of photochemical oxidants within the troposphere have been the subject of laboratory and field study throughout the last three decades. During the same period, models to simulate the atmospheric chemistry, transport and deposition of ozone (O(3)) from individual urban sources and from regions have been developed. The models differ greatly in the complexity of chemical schemes, in the underlying meteorology and in spatial and temporal resolution. Input information from land use, spatial and temporally disaggregated emission inventories and meteorology have all improved considerably in recent years and are not fully implemented in current models. The development of control strategies in both North America and Europe to close the gaps between current exceedances of environmental limits, guide values, critical levels or loads and full compliance with these limits provides the focus for policy makers and the support agencies for the research. The models represent the only method of testing a range of control options in advance of implementation. This paper describes currently applied models of photochemical oxidant production and transport at global and regional scales and their ability to simulate individual episodes as well as photochemical oxidant climatology. The success of current models in quantifying the exposure of terrestrial surfaces and the population to potentially damaging O(3) concentrations (and dose) is examined. The analysis shows the degree to which the underlying processes and their application within the models limit the quality of the model products.     

壳聚糖-TiO_2吸附剂对银的吸附及纳米银的生成

将生物选择性吸附和光催化技术耦合合成一种新型的多功能壳聚糖-二氧化钛吸附剂(CTA),这种新型的多功能壳聚糖-二氧化钛吸附剂能够同时吸附重金属和降解有机污染物。实验发现,CTA对银离子有较好的吸附容量,在初始浓度为1 000 mg/L时吸附容量为100.3 mg/g,且吸附了银离子的吸附剂对甲基橙有更好的降解效果。扫描电镜表明,CTA紫外条件下吸附银以后表面会有纳米银的生成,能谱显示纳米银颗粒在一定条件下可以由CTA表面自行脱落。     

The growth response of Alternanthera philoxeroides in a simulated post-combustion emission with ultrahigh [CO2] and acidic pollutants

Although post-combustion emissions from power plants are a major source of air pollution, they contain excess CO₂ that could be used to fertilize commercial greenhouses and stimulate plant growth. We addressed the combined effects of ultrahigh [CO₂] and acidic pollutants in flue gas on the growth of Alternanthera philoxeroides. When acidic pollutants were excluded, the biomass yield of A. philoxeroides saturated near 2000 μmol mol⁻¹ [CO₂] with doubled biomass accumulation relative to the ambient control. The growth enhancement was maintained at 5000 μmol mol⁻¹ [CO₂], but declined when [CO₂] rose above 1%, in association with a strong photosynthetic inhibition. Although acidic components (SO₂ and NO₂) significantly offset the CO₂ enhancement, the aboveground yield increased considerably when the concentration of pollutants was moderate (200 times dilution). Our results indicate that using excess CO₂ from the power plant emissions to optimize growth in commercial green house could be viable.     

二氧化铅电极的制备、表征及其电催化性能研究

以电沉积法制备了Ti/PbO2和Ti/MnO2/PbO22种电极.采用SEM、XRD和XPS等分析方法表征了电极的形貌、元素组成及元素化学态,并以罗丹明B为目标有机物,考察了所制备电极的析氧极化曲线和电催化活性以及Ti/MnO2/PbO2电极的循环伏安曲线.研究结果表明,Ti/MnO2/PbO2电极的稳定性、使用寿命、析氧电位和电催化活性较Ti/PbO2电极都有所提高,并且罗丹明B在Ti/MnO2/PbO2电极上的反应主要发生在析氧反应区,且反应不可逆.     

钛基IrO2-SnO2电极在烟气海水脱硫恢复系统中的应用

采用浸渍-热分解法制备了含IrOx-TiO2中间层的IrO2-SnO2电极,得到的电极具有较高的析氯电催化活性和较强的稳定性,并通过电化学氧化法对Na2SO3海水脱硫模拟液进行处理,考察了电流密度、温度、pH值和电解时间等电解工艺参数对Na2SO3去除率和化学需氧量COD的影响.结果表明,在电流密度为200 mA/cm...     

离子液体R3NANR3的制备及其脱硫性能

以二元酸和短链叔胺为原料,合成了已二酸三乙胺盐离子液体———R3NANR3。对该离子液体进行SO2气体的循环吸收和解吸行为的研究。实验结果表明,R3NANR3离子液体能对SO2气体进行有效的化学吸收。该吸收过程分二步进行,以第一步吸收为主。室温下(20℃)该离子液体在3 h以内吸收速率较快,3 h后吸收速率减慢并逐渐达到平衡。R3NANR3离子液体与SO2气体饱和吸收量的物质的量之比为1.08。较高温度将导致SO2气体的解吸,在90℃时饱和吸收液能较充分地解吸,残留量为0.0010 mol/L。多次吸收和解吸测试表明,R3NANR3离子液体能实现对SO2气体的循环吸收和分离,将成为烟气中SO2气体的脱除和利用的重要循环吸收剂。     

铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制简

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50 h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

O_3/H_2O_2工艺降解1,2,4-三氯苯的优化设计

考察用不同的氧化剂降解1,2,4-三氯苯(TCB),3种不同方法对TCB的去除效果存在较大差别,其处理效果依次为:H2O2O3O3/H2O2。采用响应面法优化O3/H2O2工艺降解TCB的条件。结果表明,TCB初始浓度和H2O2投加量对TCB去除效果影响较大。TCB的降解符合准一级反应动力学规律,最佳降解条件为TCB初始浓度0.3 mg/L,pH=8.13,H2O2投加量0.40 mmol/L,O3转化率75%。在此条件下,TCB的平均去除率为91.5%,与预测值93.1%吻合度较高。     

微气泡曝气 O3/ H2O2处理 RO 浓水的效能及影响因素简

采用O₃/H₂O₂高级氧化工艺处理炼油厂反渗透（RO）浓水,用溶气泵加压溶气并产生微气泡强化传质,确定装置运行条件,考察气体中臭氧浓度、H₂O₂/O₃初始摩尔比、pH和温度对O₃/H₂O₂处理RO浓水效果的影响,并对RO浓水处理效能进行研究。结果表明,随着气体中臭氧浓度的增加,COD的去除率基本呈线性增加;加入适当量H₂O₂能提高臭氧氧化RO浓水的效果,H₂O₂/O₃初始摩尔比在0~0.8范围内,COD的去除率先增加后下降,H₂O₂/O₃初始摩尔比为0.5时COD去除率最大;pH从6.84增加到9.01,COD去除率逐渐增大,pH为10.03时COD去除率反而降低;在14~28℃范围内,温度低时,升高温度COD去除率增加较大,温度较高时,升高温度对COD去除率的影响较小。为考察该工艺的稳定性,在H₂O₂/O₃初始摩尔比为0.5、溶液pH为8~9、臭氧浓度为80~100 mg/L、温度为10~28℃条件下,对COD为90~140 mg/L的RO浓水氧化处理4~10 h,出水COD维持在39.9~49.9 mg/L,达到《城镇污水处理厂污染物排放标准（GB 18918-2002）》中的一级A标准;去除1 g COD消耗O₃ 1.4~3.3 g,消耗O₃与H₂O₂的总氧量为2.2~4.4 g。     

超声波协同H_2O_2处理养殖场污水

为了有效地改善养猪场污水的质量,以H2O2为药剂,对污水进行了水浴加热和超声波辅助的对比实验,考察了超声波发生器输出端电流强度、处理时间、H2O2用量对污水的COD、氨气及颜色的影响,并进行正交实验优化。结果表明,超声波协同H2O2处理养殖污水是一种切实可行的方法,超声波协同H2O2处理污水的最佳工艺条件:电流0.7 A、处理时间2 min、H2O2用量3%,在此条件下降低COD量可达95%以上,氨氮的含量可降至14~15 mg/L,氨臭味大大得到了改善,并将原污水由黑色变为浅黄色。     

Junge relationships in measurement data for cyclic siloxanes in air

In 1974, Junge postulated a relationship between variability of concentrations of gases in air at remote locations and their atmospheric residence time, and this Junge relationship has subsequently been observed empirically for a range of trace gases. Here, we analyze two previously-published datasets of concentrations of cyclic volatile methyl siloxanes (cVMS) in air and find Junge relationships in both. The first dataset is a time series of concentrations of decamethylcyclopentasiloxane (D₅) measured between January and June, 2009 at a rural site in southern Sweden that shows a Junge relationship in the temporal variability of the measurements. The second dataset consists of measurements of hexamethylcyclotrisiloxane (D₃), octamethylcyclotetrasiloxane (D₄) and D₅ made simultaneously at 12 sites in the Global Atmospheric Passive Sampling (GAPS) network that shows a Junge relationship in the spatial variability of the three cVMS congeners. We use the Junge relationship for the GAPS dataset to estimate atmospheric lifetimes of dodecamethylcyclohexasiloxane (D₆), 8:2–fluorotelomer alcohol and trichlorinated biphenyls that are within a factor of 3 of estimates based on degradation rate constants for reaction with hydroxyl radical determined in laboratory studies.     

Impact of biochar application to a Mediterranean wheat crop on soil microbial activity and greenhouse gas fluxes

Biochar has been recently proposed as a management strategy to improve crop productivity and global warming mitigation. However, the effect of such approach on soil greenhouse gas fluxes is highly uncertain and few data from field experiments are available. In a field trial, cultivated with wheat, biochar was added to the soil (3 or 6 kg m⁻²) in two growing seasons (2008/2009 and 2009/2010) so to monitor the effect of treatments on microbial parameters 3 months and 14 months after char addition. N₂O, CH₄ and CO₂ fluxes were measured in the field during the first year after char addition. Biochar incorporation into the soil increased soil pH (from 5.2 to 6.7) and the rates of net N mineralization, soil microbial respiration and denitrification activity in the first 3 months, but after 14 months treated and control plots did not differ significantly. No changes in total microbial biomass and net nitrification rate were observed. In char treated plots, soil N₂O fluxes were from 26% to 79% lower than N₂O fluxes in control plots, excluding four sampling dates after the last fertilization with urea, when N₂O emissions were higher in char treated plots. However, due to the high spatial variability, the observed differences were rarely significant. No significant differences of CH₄ fluxes and field soil respiration were observed among different treatments, with just few exceptions. Overall the char treatments showed a minimal impact on microbial parameters and GHG fluxes over the first 14 months after biochar incorporation.     

Effects of nickel chloride and oxygen depletion on behaviour and vitality of zebrafish (Danio rerio, Hamilton, 1822) (Pisces, Cypriniformes) embryos and larvae

We examined acute (2 h exposure of 5-day-old larvae) and subchronic (exposure from fertilization up to an age of 11 days) effects of NiCl(2).6H2O on embryos and larvae of zebrafish (Danio rerio), both alone and in combination with oxygen depletion. The following endpoints were recorded: acute exposure: locomotory activity and survival; subchronic exposure: hatching rate, deformations, locomotory activity (at 5, 8 and 11 days) and mortality. In acute exposures nickel chloride (7.5-15 mg Ni/L) caused decreasing locomotory activity. Oxygen depletion (or=10 mg Ni/L resulted in delayed hatching at an age of 96 h, in decreased locomotory activity at an age of 5 days, and increased mortality at an age of 11 days (LC20=9.5 mg Ni/L). The observed LOEC for locomotory activity (7.5 mg Ni/L) is in the range of environmentally relevant concentrations. Since locomotory activity was already affected by acute exposure, this parameter is recommended to supplement commonly recorded endpoints of toxicity.