Multicriteria Aided Design of Integrated Heating-Cooling Energy Systems in Buildings

Abstract

This paper presents an analysis of the possible application of integrated heating-cooling systems in buildings. The general algorithm of integrated heating-cooling system design aid was formulated. The evaluation criteria of technically acceptable variants were defined. Fossil fuel energy consumption, carbon dioxide emission, investment, and total exploitation cost were identified as the most important factors describing the considered decision problem. The multicriteria decision aid method ELECTRE III was proposed as the decision tool for the choice of the most compromised variant. The proposed method was used for a case study calculation—the choice of an integrated heating-cooling system for an office building.     

Improving petroleum contaminated land remediation decision-making through the MCA weighting process

Internationally petroleum contamination is widespread, posing serious environmental risks including surface and groundwater contamination, thus remediation is essential. The implementation of remediation options is becoming more complex with the increasing influence of stakeholders on the outcome of decision-making processes. Acceptance of remediation schemes during implementation can be increased by involving stakeholders and the public in the decision-making stage. In petroleum remediation involving multiple stakeholders, Multicriteria Analysis has been employed due to its ability to incorporate the preferences of each stakeholder through weighting. The research focused on investigating ways to improve the weighting process. The study demonstrated the utility of SWING, and determined which type of participant and how many participants to include in the decision process, through the application of ELECTRE III and Weighted Summation. It was recommended that a mixture of stakeholders, the public and experts be involved. The total number of participants will be limited by the choice of participatory and weighting methods. The careful selection of participants, as well as the choice of participatory and weighting methods, can minimize the subjectivity involved in MCA weighting, thereby lending decisions in petroleum remediation greater legitimacy.     

One-dimensional simulation of solute transfer in saturated-unsaturated porous media using the discontinuous finite elements method

A one-dimensional transport model for simulating water flow and solute transport in homogeneous-heterogeneous, saturated-unsaturated porous media is presented. The model is composed of a combination of accurate numerical algorithms for solving the nonlinear Richard's and advection-dispersion equations (ADE). The mixed form of Richard's equation is solved using a standard finite element method (FEM) with primary variable switching. The transport equation is solved using operator splitting, with the discontinuous finite element method (DFE) for discretization of the advective term. A slope limiting procedure for DFE avoids numerical instabilities but creates very limited numerical dispersion for high Peclet numbers. An implicit finite differences scheme (FD) is used for the dispersive term. The unsaturated flow and transport model (Wamos-T) is applied to a variety of rigorous problems including transient flow, heterogeneous medium and abrupt variations of velocity in magnitude and direction due to time-varying boundary conditions. It produces accurate and mass-conservative solutions for a very large range of grid Peclet numbers. The Wamos-T model is a good and robust alternative for the simulation of mass transport in unsaturated domain.     

Citizen participation for integrated assessment: new pathways in complex systems

Citizen or community participation is a guiding principle for environmental decision-making, but in practice it is often compromised and contradictory. Two themes in participation can be defined. One is in the 'product' or outcome of decision-making, and aims for more effective and appropriate evaluations and decisions. The other is participation in the 'process', where devolved decision-making itself can serve wider social and economic goals. Although both strands are crucial for the practice of 'integrated assessment' in environmental governance, a clearer view is needed of the scope and limits of such participation. This paper explores such scope and limits by applying a conceptual 'integrated assessment' framework. This is drawn from a major case study on sustainable development for a city-region in the north of the UK. Such a framework helps to identify the many roles of citizen participation from a complex systems perspective. Selected examples of current practice highlight the problems and opportunities for citizen participation in environmental governance.     

Economic insight into municipal solid waste management in Mumbai: a critical analysis

Mumbai generates 6256 tonnes of waste every day, of which 17.20% is recyclable, but only a fraction of this is retrieved by rag-pickers. The economic value of the retrieved material is not considered by the Municipal Corporation of Greater Mumbai in valuing the waste management system as there is no retrieval mechanism except the informal rag-picking activity. Moreover, the cost of land used for the dumping of waste is also not accounted for. In the present paper, a comprehensive cost-benefit analysis for the present system of municipal solid waste management in Mumbai is carried out, with due consideration for implicit or hidden costs and benefits. Accounting for the implicit costs and benefits showed a difference of $6 per every tonne of waste disposal. This could show a considerable difference in policy development at the municipality level. Demand supply analysis proved that the present system of waste management would not yield a feasible market solution without private sector participation. With the increasing demand for improved waste management, private sector participation is essential and a Pigouvian tax is a necessary tool to make the private sector participation in solid waste management a success.     

Identifying problems for choosing suitable areas for installation of a new landfill through GIS technology: A case study

Selecting a suitable place to install a new landfill is a hard work. Bauru is a Brazilian municipality where the local landfill currently in use has a life span that is almost over, and the selection of a new area for a future landfill is crucial and urgent. Here we use a geographic information system (GIS) approach to indicate possible suitable areas for installing the landfill. The considered criteria were: river network and the respective buffer zone, relief, urban areas and their respective buffer zone, existence of Areas for Environmental Protection (AEPs), occurrence of wells and their respective buffer zones, existence of airports and their buffer zones, wind direction, and the road network and its respective buffer zone. Due the facts that (1) Bauru has an urban area relatively large in relation to whole municipal area, (2) Bauru has two airports, and (3) this area encompasses parts of three AEPs, the model showed that there are few areas suitable and moderately suitable in Bauru, and the greater part of the municipality is unsuitable to install a new landfill. Due to this important finding reported here, the local policymakers should consider the suitable or even moderately suitable areas for analysis in situ or look for other creative solutions for destination of the solid waste. We highly encourage the use of GIS in studies that seek suitable areas for future landfills, having found that SIG was a tool that allowed fast and precise work and generated an outcome sufficiently clear of interpretation.

Implications:?Solid waste (SW) management is one of the main environmental concerns nowadays. Landfilling SW is still the main practice to disposal of such material. However, for many regions, suitable places for landfilling are getting scarce. This study proved this situation for a populous place in a southeastern Brazilian region. This study also showed how the decision makers should manage the problem in order to minimize the amount of SW generated and delivered for the landfill. Massive investment in education is a critical issue to reach the proposed aim.     

Effect of Dust Concentration Upon the Gas-Flow Capacity of a Cyclonic Collector

The flow rate through an industrial gas-cleaning cyclone at a fixed pressure drop is greater when the incoming gas is dusty than when it is clean. This observation by Briggs for a single cyclone tube was extended to multiple tubes, and ike results compared to observations by Soo and Trezek that the fraction factor for turbulent flow in a pipe is less for dusty gas than for clean. Empirical considerations indicated tJtat both of these observations should be connected with a rather large reduction in gas viscosity due to the dust. This predicted viscosity decrease was later observed. A physical theory accounting for viscosity reduction by a dust cloud is proposed. This effect also offers a means for increasing the heat, transfer coefficient in gas heat exchangers.     

A pollution attenuation coefficient concept for optimization of green belt

A model for the estimation of the pollution attenuation factor of a green belt around a ground level pollution source is developed using a combination of an exponential law for dry removal of pollution within a plant canopy and a source depletion model for removal outside the canopy. A formulation for the estimation of the pollution attenuation coefficient of the exponential law is proposed and the same is tested for particulate material using the experimental data available in the literature. The dependence of the pollution attenuation factor on various parameters of the green belt is illustrated for paniculate pollution. The results show that this model can be used to optimize the design of a green belt in order to achieve a desired value of attenuation of pollution around an industry.     

One-dimensional simulation of solute transfer in saturated–unsaturated porous media using the discontinuous finite elements method

A one-dimensional transport model for simulating water flow and solute transport in homogeneous–heterogeneous, saturated–unsaturated porous media is presented. The model is composed of a combination of accurate numerical algorithms for solving the nonlinear Richard's and advection–dispersion equations (ADE). The mixed form of Richard's equation is solved using a standard finite element method (FEM) with primary variable switching. The transport equation is solved using operator splitting, with the discontinuous finite element method (DFE) for discretization of the advective term. A slope limiting procedure for DFE avoids numerical instabilities but creates very limited numerical dispersion for high Peclet numbers. An implicit finite differences scheme (FD) is used for the dispersive term.The unsaturated flow and transport model (Wamos-T) is applied to a variety of rigorous problems including transient flow, heterogeneous medium and abrupt variations of velocity in magnitude and direction due to time-varying boundary conditions. It produces accurate and mass-conservative solutions for a very large range of grid Peclet numbers. The Wamos-T model is a good and robust alternative for the simulation of mass transport in unsaturated domain.     

Phase-in of nonpoint sources in a transferable discharge permit system for water quality management: setting permit prices

The composite market design is a proposal for a transferable discharge permit system that specifically includes agricultural non-point-source dischargers and addresses both property rights and transaction cost problems. The first step to implementation of a composite market scheme is the estimation of a supply curve for abatement measures in the catchment area. Estimation is performed by combining costs with modeled loss reductions from selected best management practices and then using this information to estimate the supply curve for abatement, which in turn can then be used to set permit prices. The R?nne? catchment in southern Sweden is used as a pilot study area for making this type of estimate. Costs for existing measures that reduce nutrient losses from farmland (catch crops and spring planting) are based on existing programs financed by the Swedish Agricultural Board. A set of supply curves is calculated for these measures using retention estimates for seven subcatchments and three soil types in the area. Although existing information is sufficient to calculate partial supply curves and may be used to set permit prices, additional measures should be included as well as an increased number of variables for differentiating site specific reduction costs.     

Towards a better understanding of tetrachloroethene entry pressure in the matrix of Permo-Triassic sandstones

The pressure required for a chlorinated solvent to enter a geological medium can be calculated given knowledge of the characteristic pore size of the medium and the interfacial tension (IFT) and contact angle of the solvent-water-rock system. Using a centrifuge-based method, capillary pressure-saturation curves have been determined for 30 water-saturated samples of Permo-Triassic sandstones for the solvent tetrachloroethene (PCE). These curves have been successfully fitted using the van Genuchten function to determine PCE entry pressure for each of the sandstone samples. A plot of PCE entry pressures against average pore diameter shows a linear relationship in log-log space; however, observed values for PCE entry pressure are significantly lower than would be expected theoretically for a sandstone-PCE-water system. This may be explained either by a decrease in the IFT or an increase in the contact angle. The IFT may decrease during contact with sandstones due to hysteresis effects during imbibition and drainage of fluids, but this is unlikely to be sufficient to account for the low entry pressures observed. Therefore, it is inferred that the low observed PCE entry pressures are due to higher than expected PCE contact angles, and that the average pore-throat surface of the sandstones is more solvent wetting than would be expected. A weak acid extraction indicates the presence of calcite and dolomite in the sandstone cores, and a correlation is observed between carbonate content per unit porosity and a reduction in PCE entry pressure. It is suggested that these mineral phases are responsible for observed wettability changes and a conceptual model is proposed. One consequence of the lower observed entry pressures is that solvents are likely to penetrate deeper into the matrix of water-saturated sandstones than previously expected.     

Oxygen Stratification in Industrial Boiler Stacks

The DSS/2 software system was used to numerically simulate oxygen stratification effects in a typical industrial boiler stack. The model developed for the simulation involves turbulent mass transfer in a tube with a constant, high mass flux from the walls of the tube. The concentration profile is considered to be developing, but the velocity profile is assumed to be fully developed. The model is for a gaseous system at constant temperature and pressure; the transport properties are shown to be constant. The universal velocity profile for turbulent flow and von Karman’s expressions for the turbulent eddy diffusivity are incorporated in the model. An expression for a wall concentration profile corresponding to conditions of high mass flux at the wall is developed. The model is then expressed as a system of partial differential equations which are solved using the numerical method of lines together with the DSS/2 numerical integration system. The resulting concentration profiles are presented for various flux rates which might be encountered in a typical stack. These profiles indicate that a potential for oxygen stratification in stacks does exist; they also suggest that careful placement of the oxygen cell probe can help minimize such errors.     

A fast and efficient modified sectional method for simulating multicomponent collisional kinetics

A fast and efficient method for simulating the evolution of internally mixed multicomponent particle size distributions for aerosol coagulation and droplet coalescence is developed. The technique is based upon a bin-wise sectionalization of the particle mass domain and by imposing the condition of mass conservation for each component. The distribution of each species as a function of the total particle mass is represented in each mass bin as a two-parameter exponential function. Particles of a given mass are assumed to be internally homogeneously mixed. The method is shown to be numerically stable for a wide range of time steps. The numerical solution is compared with both analytical results and results from other well-accepted numerical schemes. This comparison reveals that the proposed technique offers the advantage of being fast and accurate, even for coarse spectral resolution. The method is computationally attractive and easily allows the treatment of ten or more different chemical species in a collisionally evolving particle size distribution. The applicability of the method is demonstrated with several examples: Coalescence growth of multicomponent cloud droplet spectra, coagulation of measured multi-species aerosol particle size distributions, and the simulation of the accumulation mode due to a source of small aerosol particles. The technique is ideally suited for modelling the interaction of microphysics and chemistry in a size-bin resolving aerosol or cloud model.     

Nuclear power in the 21st century: Challenges and possibilities

The current situation and possible future developments for nuclear power—including fission and fusion processes—is presented. The fission nuclear power continues to be an essential part of the low-carbon electricity generation in the world for decades to come. There are breakthrough possibilities in the development of new generation nuclear reactors where the life-time of the nuclear waste can be reduced to some hundreds of years instead of the present time-scales of hundred thousand of years. Research on the fourth generation reactors is needed for the realisation of this development. For the fast nuclear reactors, a substantial research and development effort is required in many fields—from material sciences to safety demonstration—to attain the envisaged goals. Fusion provides a long-term vision for an efficient energy production. The fusion option for a nuclear reactor for efficient production of electricity has been set out in a focussed European programme including the international project of ITER after which a fusion electricity DEMO reactor is envisaged.     

A holistic passive integrative sampling approach for assessing the presence and potential impacts of waterborne environmental contaminants

As an integral part of our continuing research in environmental quality assessment approaches, we have developed a variety of passive integrative sampling devices widely applicable for use in defining the presence and potential impacts of a broad array of contaminants. The semipermeable membrane device has gained widespread use for sampling hydrophobic chemicals from water and air, the polar organic chemical integrative sampler is applicable for sequestering waterborne hydrophilic organic chemicals, the stabilized liquid membrane device is used to integratively sample waterborne ionic metals, and the passive integrative mercury sampler is applicable for sampling vapor phase or dissolved neutral mercury species. This suite of integrative samplers forms the basis for a new passive sampling approach for assessing the presence and potential toxicological significance of a broad spectrum of environmental contaminants. In a proof-of-concept study, three of our four passive integrative samplers were used to assess the presence of a wide variety of contaminants in the waters of a constructed wetland, and to determine the effectiveness of the constructed wetland in removing contaminants. The wetland is used for final polishing of secondary-treatment municipal wastewater and the effluent is used as a source of water for a state wildlife area. Numerous contaminants, including organochlorine pesticides, polycyclic aromatic hydrocarbons, organophosphate pesticides, and pharmaceutical chemicals (e.g., ibuprofen, oxindole, etc.) were detected in the wastewater. Herein we summarize the results of the analysis of the field-deployed samplers and demonstrate the utility of this holistic approach.     

A robust approach for iterative contaminant source location and release history recovery

Contamination source identification is a crucial step in environmental remediation. The exact contaminant source locations and release histories are often unknown due to lack of records and therefore must be identified through inversion. Coupled source location and release history identification is a complex nonlinear optimization problem. Existing strategies for contaminant source identification have important practical limitations. In many studies, analytical solutions for point sources are used; the problem is often formulated and solved via nonlinear optimization; and model uncertainty is seldom considered. In practice, model uncertainty can be significant because of the uncertainty in model structure and parameters, and the error in numerical solutions. An inaccurate model can lead to erroneous inversion of contaminant sources. In this work, a constrained robust least squares (CRLS) estimator is combined with a branch-and-bound global optimization solver for iteratively identifying source release histories and source locations. CRLS is used for source release history recovery and the global optimization solver is used for location search. CRLS is a robust estimator that was developed to incorporate directly a modeler's prior knowledge of model uncertainty and measurement error. The robustness of CRLS is essential for systems that are ill-conditioned. Because of this decoupling, the total solution time can be reduced significantly. Our numerical experiments show that the combination of CRLS with the global optimization solver achieved better performance than the combination of a non-robust estimator, i.e., the nonnegative least squares (NNLS) method, with the same solver.     

Comparison of metastable atom bombardment and electron capture negative ionization for the analysis of polychloroalkanes

A new method for quantifying C10-C13 polychloroalkanes (PCAs or chloroparaffins, CPs) in environmental samples using metastable atom bombardment ionization (MAB) and high resolution mass spectrometry is presented. Contrary to electron capture negative ionization (ECNI), MAB can produce spectra for molecules having a low number of chlorine atoms. These molecules are present in commercial PCAs and are responsible for a large fraction of the total PCA concentration in water samples analysed. Using ECNI or MAB, no molecular ion can be seen in the spectra. ECNI spectra contain important peaks corresponding to [M-Cl]- and [M-HCl]-* while the base peak in MAB spectra is [M-Cl]+ with no [M-HCl]+* present. The mass range for C10-C13 CPs is very large and scanning the masses for all the compounds involved would lead to a loss of sensitivity. Two chromatographic analysis are thus performed using high resolution selective ion monitoring with only a limited number of masses recorded per run. To reduce analysis time, a short capillary column is used. Application of this method to the analysis of high-volumes water samples (dissolved and particulates portions separately) from the St. Lawrence river near Quebec City using MAB is presented. Contribution of molecules with a low chlorine content in the samples account for between 10% and 46% to the total concentration. Congeners distribution between the different fractions indicates that molecules with a low number of carbon atoms are preferentially retained on the particulates. Within a carbon number group, there is a slight tendency to accumulate molecules with a high number of chlorine atoms in the dissolved fraction.     

The Formulation of Emission Control Strategies Using a Cubic Polynomial Approximation

Assuming the existence of an ambient air standard for a given pollutant, there is some agreement that emission standards for local area and point sources should be established by formulating and testing various “control strategies” with use of a computer diffusion model. The procedure requires several, perhaps many, computer simulations of pollutant dispersion followed by an analysis of the results of each simulation. Part of this analysis is to include an “optimization” of sorts which is intended to provide a workable control strategy which, in turn, is to indicate required emission level reductions for point sources. This paper is intended to describe and apply an approximation technique which, when used in conjunction with a diffusion model, could be of value in determining acceptable emission levels for point sources.     

酶体外定向分子进化技术:环境生物污染治理中的新星

环境生物技术在环境控制与污染治理中的应用主要是利用微生物降解和转换污染物.一些人类合成的化学物质由于具有高毒性,且难以被自然界微生物降解,已经严重威胁生态环境和人类的健康.生物治理以其低成本、完成矿质化和实现原位处理等特点,成为较好的治理技术.体外定向分子进化技术是一种发现新的生物表型和新酶的好方法,DNA改组是重要的体外分子进化技术,成功地改造了许多在医药、工业和环境保护等的商业酶.综述了近年来体外定向分子进化技术在环境生物污染治理中的研究进展和应用.