Influence of mechanical-biological waste pre-treatment methods on the gas formation in landfills

In order to minimise emissions and environmental impacts, only pre-treated waste should be disposed of. For the last six years, a series of continuous experiments has been conducted at the Institute WAR, TU Darmstadt, in order to determine the emissions from pre-treated waste. Different kinds of pre-treated waste were incubated in several reactors and various data, including production and composition of the gas and the leachate, were collected. In this paper, the interim results of gas production and the gas composition from different types of waste after a running time of six years are presented and discussed.     

Water regime of mechanical-biological pretreated waste materials under fast-growing trees.

In this study mechanical-biological pre-treated waste material (MBP) was tested for suitability to serve as an alternative surface layer in combination with fast-growing and water-consumptive trees for final covers at landfill sites. The aim was to quantify evapotranspiration and seepage losses by numerical model simulations for two sites in Germany. In addition, the leaf area index (LAI) of six tree species over the growing season as the driving parameter for transpiration calculations was determined experimentally. The maximum LAI varied between 3.8 and 6.1 m2 m(-2) for poplar and willow clones, respectively. The evapotranspiration calculations revealed that the use of MBP waste material for re-cultivation enhanced evapotranspiration by 40 mm year(-1) (10%) over an 11 year calculation period compared to a standard mineral soil. Between 82% (for LAI(max) = 3.8) and 87% (for LAI(max) = 6.1) of the average annual precipitation (506 mm) could be retained from the surface layer assuming eastern German climate conditions, compared with a retention efficiency between 79 and 82% for a mineral soil. Although a MBP layer in conjunction with water-consumptive trees can reduce vertical water losses as compared to mineral substrates, the effect is not sufficient to meet legal regulations.     

Dynamic transformations of nitrogen during mechanical-biological pre-treatment of municipal solid waste

Mechanical-biological pre-treatment (MBP) of municipal solid waste (MSW) has gained evidence as a practice capable of accomplishing the requirements for environmental sustainable landfilling. In particular, MBP is effective in reducing the ammoniacal nitrogen content in the leachate. However, few data are available on the modifications of the nitrogen forms occurring during MBP and on the role played by processes such as nitrification and generation of refractory organic compounds. The dynamic transformations of nitrogen were investigated during the MBP. MSW was mechanically and biologically pre-treated; samples were collected at different stages of the process and analysed to investigate the evolution of nitrogen forms; batch and column leaching tests were performed as well. The results indicate that nitrification is negligible and volatilization can only partially explain the low ammoniacal nitrogen content in the leachate. Incorporation of ammoniacal nitrogen into a refractory organic form was assessed and is likely to play an important role. The maximum content of refractory organic nitrogen in the solid waste was achieved after about 60 days of aerobic pre-treatment; therefore, the minimal duration of the MBP should be about 8-9 weeks in order to optimize the ammoniacal nitrogen incorporation, unless the waste is characterized by a low C/N ratio.     

Mass balance to assess the efficiency of a mechanical-biological treatment

Using mechanical-biological treatment of residual municipal solid waste, it is possible to significantly lower landfill volume and gas and leachate emissions. Moreover, the landfill characteristics are improved. The performance of the Mende (France) mechanical-biological treatment plant is assessed via mass balances coupled with manual sorting according to the MODECOMtrade mark methodology and biochemical methane potential after 90 days of incubation. The site includes mechanical sorting operations, a rotary sequential bioreactor, controlled aerobic stabilisation corridors, maturation platforms, and a sanitary landfill site for waste disposal in separated cells. Results showed that several steps could be improved: after a first sieving step, about 12% of the potentially biodegradable matter is landfilled directly without any treatment; mechanical disintegration of papers and cardboards in the rotary sequential bioreactor is insufficient and leads to a high proportion of papers and cardboards being landfilled without further treatment. Two fine fractions go through stabilisation and maturation steps. At the end of the maturation step, about 54% of the potentially biodegradable matter is degraded. The biochemical methane potential after 90 days of incubation is reduced by 81% for one of the two fine fractions and reduced by 88% for the other one. Considering the whole plant, there is a reduction of nearly 20% DM of the entering residual municipal solid waste.     

Baseline levels of bioaerosols and volatile organic compounds around a municipal waste incinerator prior to the construction of a mechanical-biological treatment plant

New waste management programs are currently aimed at developing alternative treatment technologies such as mechanical–biological treatment (MBT) and composting plants. However, there is still a high uncertainty concerning the chemical and microbiological risks for human health, not only for workers of these facilities, but also for the population living in the neighborhood. A new MBT plant is planned to be constructed adjacently to a municipal solid waste incinerator (MSWI) in Tarragona (Catalonia, Spain). In order to evaluate its potential impact and to differentiate the impacts of MSWI from those of the MBT when the latter is operative, a pre-operational survey was initiated by determining the concentrations of 20 volatile organic compounds (VOCs) and bioaerosols (total bacteria, Gram-negative bacteria, fungi and Aspergillus fumigatus) in airborne samples around the MSWI. The results indicated that the current concentrations of bioaerosols (ranges: 382–3882, 18–790, 44–926, and <1–7 CFU/m³ for fungi at 25 °C, fungi at 37 °C, total bacteria, and Gram-negative bacteria, respectively) and VOCs (ranging from 0.9 to 121.2 μg/m³) are very low in comparison to reported levels in indoor and outdoor air in composting and MBT plants, as well in urban and industrial zones. With the exception of total bacteria, no correlations were observed between the environmental concentrations of biological agents and the direction/distance from the facility. However, total bacteria presented significantly higher levels downwind. Moreover, a non-significant increase of VOCs was detected in sites closer to the incinerator, which means that the MSWI could have a very minor impact on the surrounding environment.     

Composition analysis of dental solid waste in Brazil

When developing proper waste management strategies, it is essential to characterize the volume and composition of solid waste. The aim of this work was to evaluate the composition of dental waste produced by three dental health services in Belo Horizonte, Minas Gerais State, Brazil. Two universities, one public and one private, and one public dental health service were selected. Waste collection took place from March to November 2007. During this period, three samples were collected from each dental health service. The total amount of dental waste produced in one day of dental work was manually separated into three categories: infectious and potentially infectious waste, accounting for 24.3% of the total waste; non-infectious waste, accounting for 48.1%; and domestic-type waste, accounting for 27.6% (percentages are for mean weights of solid waste). Our results showed that most of the waste considered as biomedical may be misclassified, consequently making the infectious waste amount appear much larger. In addition, our results suggest that the best waste minimization method is recycling, and they help to define an appropriate waste management system in all three of the dental health services involved in this study.     

北京市建筑废弃物资源化利用研究与项目示范

针对北京市建筑废弃物产量大、资源化利用率低的问题,分析了北京市建筑废弃物的来源、产量、组分及处理现状,阐述了建筑废弃物资源化利用途径和资源化利用工艺,介绍了朝阳区建筑废弃物资源化示范项目建设情况,给出了北京市建筑废弃物资源化利用设施建设合理建议。     

生物滴滤法处理药厂高浓度丙酮废气的中试研究

采用生物滴滤工艺对某药厂硫代纯化车间的高浓度丙酮废气进行中试规模的处理运行。现场风量在3000~4000 m^3/h范围波动,丙酮质量浓度在0~2278 mg/m^3范围波动。在39 d的运行期间,丙酮的平均脱除效率为78%,最高可达100%;系统的平均单位去除负荷为139.2 g/(h·m^3),最高可达482.1 g/(h·m^3)。在高浓度高波动的进气工况条件下,单位生物矿化量可以保持相对稳定的水平,波动范围为11.5~27.3 g/(h·m^3),生物系统的稳定性和鲁棒性较好。循环液COD与进气负荷具有一定的相关性。     

Work safety in waste treatment

Accident risks in waste treatment were studied at five sanitary landfills, two plants using mainly manual sorting and one incineration plant in southern Finland. Work hazards were detected by means of safety analysis. In addition, accident statistics were used. Work safety problems were found at all work stages. At the sanitary landfills, the major safety problems were posed by operation of the compactor or other machinery and by hazardous wastes. In waste sorting, common problems are odour and dust, lacerations and back injuries. Falling into the waste compactor or paper silos may cause fatal injury and its probability was also high. The highest noise level measured was 97 dB(A). In waste incineration, the most serious hazards were caused by fires, clogging of the funnels and cleaning of the grate. Most deficiencies in work safety can be remedied at a moderate price. The corrective measures involve technical solutions, working methods, supervision, training and occupational health services. The accident rates for workers in the four waste treatment plants were slightly lower than the average for industry.     

A qualitative descriptive case study on home medical waste management in Brazil

Journal of Material Cycles and Waste Management - This work presents a survey on the management of the home medical care waste (HMCW) from the municipality of Caruaru, an important medical and...     

废旧电脑的综合处理与处置

随着社会文明的高速发展,越来越多的高科技新兴产品进入人们的生活,带给人们更多的方便和享受的同时,也使城市生活垃圾结构发生了很大的改变,废电池、废电冰箱、废电脑等家用电器及其废物的另类生活垃圾成为今天新的环境问题.从环境管理和绿色处理的角度,综合概述了国内外废旧电脑处理的现状,结合国外的发展经验从绿色处理的角度对废旧电脑的处理与处置方法提出了一些建议.     

The role of intergenerational influence in waste education programmes: the THAW project

Whilst the education of young people is often seen as a part of the solution to current environmental problems seeking urgent attention, it is often forgotten that their parents and other household members can also be educated/influenced via home-based educational activities. This paper explores the theory of intergenerational influence in relation to school based waste education. Waste Watch, a UK-based environmental charity (www.wastewatch.org.uk), has pioneered a model that uses practical activities and whole school involvement to promote school based action on waste. This methodology has been adopted nationally. This paper outlines and evaluates how effective school based waste education is in promoting action at a household level. The paper outlines Waste Watch's 'Taking Home Action on Waste (THAW)' project carried out for two and half years in Rotherham, a town in South Yorkshire, England. The project worked with 6705 primary age children in 39 schools (44% of primary schools in the project area) to enable them to take the "reduce, reuse and recycle message" home to their families and to engage these (i.e. families) in sustainable waste management practices. As well as substantial increases in students' knowledge and understanding of waste reduction, measurement of the impact of the project in areas around 12 carefully chosen sample schools showed evidence of increased participation in recycling and recycling tonnages as well as declining levels of residual waste. Following delivery of the project in these areas, an average increase of 8.6% was recorded in recycling set out rates which led to a 4.3% increase in paper recycling tonnages and an 8.7% increase in tonnages of cans, glass and textiles collected for recycling. Correspondingly, there was a 4.5% fall in tonnages of residual waste. Waste Watch's THAW project was the first serious attempt to measure the intergenerational influence of an education programme on behaviour at home (i.e. other than schools' own waste). It clearly shows that household recycling behaviour can be positively impacted by intergenerational influence via a practical school-based waste education model. However, although the model could potentially have a big impact if rolled out nationally, it will require seed funding and the long-term durability of the model has not yet been fully quantified.     

Risk evaluation with waste scenario: lead emissions in solder waste treatment

In this work, an estimate of the elevation of airborne lead concentrations via the lead solder contained in domestic electricity installations and an investigation into the effects of human exposure were conducted using a simulation method. The elevation of airborne lead concentrations due to incineration was calculated to be 0.001 µg/m³ maximum. The simulation results of the calculations indicated that blood lead concentrations could reach as high as 10⁻⁵ µg/dl. These concentrations could primarily be attributed to the inhalation of airborne lead particles. In addition, we discuss the influences of lead solder disposal on the ecosystem via soil and water.     

A model for estimation of potential generation of waste electrical and electronic equipment in Brazil

Sales of electrical and electronic equipment are increasing dramatically in developing countries. Usually, there are no reliable data about quantities of the waste generated. A new law for solid waste management was enacted in Brazil in 2010, and the infrastructure to treat this waste must be planned, considering the volumes of the different types of electrical and electronic equipment generated.This paper reviews the literature regarding estimation of waste electrical and electronic equipment (WEEE), focusing on developing countries, particularly in Latin America. It briefly describes the current WEEE system in Brazil and presents an updated estimate of generation of WEEE. Considering the limited available data in Brazil, a model for WEEE generation estimation is proposed in which different methods are used for mature and non-mature market products.The results showed that the most important variable is the equipment lifetime, which requires a thorough understanding of consumer behavior to estimate. Since Brazil is a rapidly expanding market, the “boom” in waste generation is still to come. In the near future, better data will provide more reliable estimation of waste generation and a clearer interpretation of the lifetime variable throughout the years.     

Industrial hazardous waste treatment facilities in Thailand

In Thailand, hazardous waste is becoming a major problem, especially toxic chemicals and heavy metal pollutants discharged from factories. The Industrial Works Department (IWD), which has full responsibility for the control of all factory pollution problems, has initiated a joint hazardous waste treatment programme for handling industrial liquid, sludge and solid hazardous wastes from all factories situated in and around Bangkok and the eastern seaboard region. Four industrial hazardous wastes treatment centres are planned. Secure landfills together with research and development centres will also be provided nearby for the ultimate disposal of the inert-salt sludges. The investment, operation and management of the centres is to be handled by private companies which can generate revenue by charging service fees directly to their customers. Since both governmental and private sectors have no experience in this field, a grant system for a pilot centre has been launched by the Government which has reduced the operating costs by providing land, treatment facilities, infrastructure and secured landfills. The first treatment centre which was officially planned in 1985 was put into operation in July 1988 at Samea Dam, Bangkhuntien District, a western suburb of Bangkok. The construction of all necessary facilities was paid for by the Government. The operation and management of the centre is handled by a private contractor, Siam Control Company (SCC) under a 5-year lease. The users will pay service fees directly to the contractor and the Government will receive a rental and royalty fee from the contractor.     

Food waste treatment in a community center

For urban community composting centers, the proper selection and use of bulking agent is a key element in not only the cost but also the quality of the finished compost. Besides wood chips (WC) widely used as BA, readily usable cereal residue pellets (CRP) can provide biodegradable carbon and sufficient free air space (FAS) to produce stabilizing temperatures. The objective of the present project was to test at a community center, the effectiveness of CRP in composting food waste (FW). Two recipes were used (CRP with and without WC) to measure: FAS; temperature regimes, and; losses in mass, water, carbon and nitrogen. Both recipes were composted during three consecutive years using a 2 m³ commercial in-vessel composter operated in downtown Montreal (Canada). For all recipes, FAS exceeded 30% for moisture content below 60%, despite yearly variations in FW and BA physical properties. When properly managed by the center operator, both FW and CRP compost mixtures with and without WC developed within 3 days thermophilic temperatures exceeding 50 °C. The loss of total mass, water, carbon and nitrogen was quite variable for both recipes, ranging from 36% to 54%, 42% to 55%, 48% to 65%, and 4% to 55%, respectively. The highest loss in dry mass, water and C was obtained with FW and CRP without WC aerated to maintain mesophilic rather than thermophilic conditions. Although variable, lower nitrogen losses were obtained with CRP and WC as BA, compared to CRP alone, as also observed during previous laboratory trials. Therefore and as BA, CRP can be used alone but nitrogen losses will be minimized by adding WC. Compost stabilization depends on operator vigilance in terms of aeration. The measured fresh compost density of 530-600 kg/m³ indicates that the 2 m³ in-vessel composter can treat 6.5 tons of FW/year if operated during 7 months.     

纳米材料在水处理中的应用

从纳米光催化氧化技术、纳米膜过滤技术和纳米吸附材料等三方面分别介绍了纳米技术在水处理方面的研究和应用情况.     

Count, identification and antimicrobial susceptibility of bacteria recovered from dental solid waste in Brazil

In Brazil, few studies on microbial content of dental solid waste and its antibiotic susceptibility are available. An effort has been made through this study to evaluate the hazardous status of dental solid waste, keeping in mind its possible role in cross-infection chain. Six samples of solid waste were collected at different times and seasons from three dental health services. The microbial content was evaluated in different culture media and atmospheric conditions, and the isolates were submitted to antibiotic susceptibility testing. A total of 766 bacterial strains were isolated and identified during the study period. Gram-positive cocci were the most frequent morphotype isolated (48.0%), followed by Gram-negative rods (46.2%), Gram-positive rods (5.0%), Gram-negative-cocci (0.4%), and Gram-positive coccobacillus (0.1%). Only two anaerobic bacteria were isolated (0.3%). The most frequently isolated species was Staphylococcus epidermidis (29.9%), followed by Stenotrophomonas maltophilia (8.2%), and Enterococcus faecalis (6.7%). High resistance rate to ampicillin was observed among Gram-negative rods (59.4%) and Gram-positive cocci (44.4%). For Gram-negative rods, high resistance was also noted to aztreonam (47.7%), cefotaxime (47.4%), ceftriaxone and cefazolin (43.7%), and ticarcillin-clavulanic acid (38.2%). Against Gram-positive cocci penicillin exhibit a higher resistance rate (45.0%), followed by ampicillin, erythromycin (27.2%), and tetracycline (22.0%). The present study demonstrated that several pathogenic bacteria are present in dental solid waste and can survive after 48 h from the waste generation time and harbor resistance profiles against several clinical recommended antibiotics.     

IC反应器处理MTO废水的中试研究

中试研究了内循环(IC)反应器处理甲醇制烯烃(MTO)废水的启动和运行过程,同时考察了颗粒污泥的性状及沼气产量的变化情况。试验过程运行稳定,系统抗冲击性强。以絮状污泥为接种污泥,经过131 d的启动和运行,IC反应器的COD去除负荷可达10 kg/(m~3·d)以上,COD去除率可达90%以上。IC反应器中的成熟颗粒污泥形状规则、密实、粒径大、沉降速率快。IC反应器的沼气产量符合理论预期。     

Visual diagnosis of solid waste contamination of a tourist beach: Pernambuco, Brazil

The solid waste accumulation patterns on Tamandaré beach, Pernambuco State (Brazil), was assessed from February 2001 to July 2002. This beach is easily accessible, frequently used, and there is a public cleaning service. The beach is under the influence of three small coastal drainage basins. The study visually divided the beach into 15 segments according to the level of solid waste contamination into absent (A), trace (B), unacceptable (C) and objectionable (D). The lowest levels of contamination were found at the middle part of the study area, the most vulnerable in respect to coastal erosion presenting numerous interventions on the beach, absence of native vegetation and lesser width. The highest levels of contamination were at the northern and southern ends of the area, where there are no developments, the beach morphology favours deposition of sediments, there is native vegetation and the beach is wider. The D level did not occur within the area.