Investigation the effect of adding graphene oxide into diesel/higher alcohols blends on a diesel engine performance

ABSTRACT

This article aims to study the influence of the addition of graphene oxide nanoparticles (GO) to diesel/higher alcohols blends on the combustion, emission, and exergy parameters of a CI engine under various engine loads. The higher alcohols mainly n-butanol, n-heptanol, and n-octanol are blended with diesel at a volume fraction of 50%. Then, the 25 and 50 mg/L concentrations of GO are dispersed into diesel/higher alcohols blends using an ultrasonicator. The GO structures are examined using TEM, TGA, XRD and FTIR. The findings show that there is a reduction in p_max. and HRR when adding higher alcohols with diesel fuel. Regarding engine emission, there is a significant improvement in emissions formation with adding higher alcohols. The addition of GO into diesel/higher alcohols blends improves the brake thermal efficiency by 15%. Moreover, the p_max. and HRR are both enhanced by 4%. The CO, UHC and smoke formation are reduced considerably by 40%, 50 and 20%, respectively, while NO_x level is increased by 30% with adding GO. Finally, adding high percentages of n-butanol, n-heptanol, and n-octanol with diesel fuel with the presence of GO has the potential to achieve ultra-low CO, UHC, and smoke formation meanwhile keeping high thermal efficiency level.     

Effective application of ethanol in diesel engines

This work aimed to prove the effects of adding different proportions of ethanol with diesel (DE) and ethanol–water mixture with diesel (DEW) in a single-cylinder diesel engine on the performance, emissions, and combustion parameters. The blends were stabilized by tetra methyl ammonium bromide (TMAB) as the additive. The study was conducted at two operating conditions initially on a normal diesel engine and in the second case the engine piston, valves, and cylinder head coated with zirconia (ZrO₂) alumina (Al₂O₃). The results showed that the addition of 10% ethanol with diesel performed almost equivalent to neat diesel with 29.2% BTE and a 17.7% decrease in smoke and an 11.4% increase in NOx emission at peak load compared to that of the base fuel. Modified engines with thermal barrier coating (TBC) performed superior to normal engines with 4% and 5.5% increase in BTE, respectively, for DE- and DEW-type fuels with reduced exhaust emissions. A 5% addition of water with diesel–ethanol blends favors a higher proportion of ethanol to be employed in diesel engines.     

Performance evaluation of Nahar oil–diesel blends in a single cylinder direct injection diesel engine

This study attempts to use plentiful available high oil content (67% of Nahar seed kernel) non-edible feedstock as a source for powering diesel engine. Various performance and emission characteristics of prepared Nahar oil–diesel blends (5%, 10%, 20%, 30%, and 40%) are analyzed in a single cylinder direct injection diesel engine at different load spectrum, in order to judge the optimum blend, which can be efficiently used in a diesel engine. 10% blending of Nahar oil with diesel fuel has shown a reduction in hydrocarbon and carbon monoxide emission by 8.64% and 8.34%, respectively. With the increase in blend concentration, the nitrogen oxide emission decreased considerably and smoke emission increased slightly. Further pressure crank angle and heat release rate analysis of 10% blending of Nahar oil with diesel confirms its smooth combustion inside the engine combustion chamber.     

Performance analysis of bioethanol (Water Hyacinth) on diesel engine

The increasing consumption and excessive extraction of conventional fuels is the matter of serious concern. Nowadays, world is looking for alternative sources of fuel which can partially replace conventional fuel dependence. The current investigation intends to provide evaluation of bio-ethanol preparation from Water Hyacinth (WH) and its influence on diesel engine performance under various operating conditions. This study explores the extraction of glucose from WH (Eichhornia crassipes) pretreated with sulfuric acid (H₂SO₄) for production of bio-ethanol. For the production of bio-ethanol different concentrations of H₂SO₄ acid hydrolysate (1%, 2%, 4%, 6%, 8%, and 10%) were prepared which was then followed by fermentation with cellulose fermenting yeasts. From results, it was observed that 4% H₂SO₄ acid hydrolysis produces higher concentrations of ethanol than other concentrations. Bio-ethanol extracted from WH was blended with diesel in different proportions (5%, 10%, 15%, 20%, and 25%) v/v and performance and emissions were experimentally investigated on single cylinder diesel engine under various load conditions. Experimental results show that 5 BED [5% bio-ethanol (WH + 95%diesel v/v) and 10BED (10% bio-ethanol (WH + 90%diesel v/v)] produces higher brake power, brake thermal efficiency and brake mean effective pressure with improved exhaust emission profiles than any other blend.     

Performance of a diesel engine with water emulsified diesel prepared with optimized process parameters

An attempt has been made to produce stable water–diesel emulsion with optimal formulation and process parameters and to evaluate the performance and emission characteristics of diesel engine using this stable water–diesel emulsion. A total of 54 samples were prepared with varying water/diesel ratio, surfactant amount and stirring speed and water separation was recorded after 24 and 48 hr of emulsification. The recorded data were used in artificial neural network (ANN)-particle swarm optimization (PSO) technique to find the optimal parameters to produce water–diesel emulsion for engine testing. The predicted optimal parameters were found as 20% water to diesel ratio, 0.9% surfactant and 2200 rpm of stirrer for a water separation of 14.33% in one day with a variation of 6.54% against the actual value of water separation. Water–diesel emulsion fuel exhibited similar fuel properties as base fuel. The peak cylinder gas pressure, peak pressure rise rate and peak heat release rate for water–diesel were found higher as compared to diesel at medium to full engine loads. The improved air-fuel mixing in water–diesel emulsion enhanced brake thermal efficiency (BTE) of engine. The absorption of heat by water droplets present in water–diesel emulsion led to reduced exhaust gas temperature (EGT). With water–diesel emulsion fuel, the mean carbon monoxide (CO), unburned hydrocarbon and oxides of nitrogen (NO_x) emissions reduced by 8.80, 39.60, and 26.11%, respectively as compared to diesel.     

Experimental investigations on direct injection diesel engines using grape seed oil methyl ester with different bowl geometries

In this paper, the performance of direct injection diesel engine was experimentally investigated under the influence of two different pistons’s geometry deep bowl combustion chamber (DBCC) and toroidal combustion chamber (TCC) compared with standard piston combustion chamber (SPCC) geometry. The experiments were carried out standard atmospheric conditions of 1.01325 bar and 30 ± 2 °C. The piston bowl was designed and developed without modifying the compression ratio of the engine. The investigations were carried out with B25 (25% GOME + 75% diesel), B50 (50% GOME + 50% diesel), B75 (75% GOME +25% diesel) and B100 (100% GOME) by volume blends for three different bowl geometries. The thermogravimetric analysis (TGA) was given the importance of higher in-cylinder temperature for the mass change of GOME leads to a more premixed phase of combustion. The results showed that DBCC has better combustion characteristics when compared with SPCC and TCC for all the blends. The B25 and B50 blends showed good combustion characteristics with DBCC and SPCC individually. While TCC showed average engine characteristics for all the blends categorically, the brake thermal efficiency for B25 blend confirmed a 4.7% higher than SPCC-diesel with DBCC piston, and the smoke, CO (Carbon monoxide), and HC (Hydrocarbon) are reduced by 9.2%, 30.7%, and 4.6%, respectively. Thus, the B25 blend in a DBCC piston engine was observed to be the distinction than other configurations. The results confirmed that the DBCC is a good option for B25 blend.     

Effects of fuel reactivity and injection timing on diesel engine combustion and emissions

Recent strategies for simultaneously reducing NOx and soot emissions have focused on achieving nearly premixed, low-temperature combustion (LTC) in diesel engines. A promising approach in this regard is to vary fuel reactivity in order to control the ignition delay and optimize the level of premixing and reduce emissions. The present study examines such a strategy by performing 3-D simulations in a single-cylinder of a diesel engine. Simulations employ the state-of-the-art two-phase models and a validated semi-detailed reaction mechanism. The fuel reactivity is varied by using a blend of n-heptane and iso-octane, which represent surrogates for gasoline and diesel fuels, respectively. Results indicate that the fuel reactivity strongly influences ignition delay and combustion phasing, whereas the start of injection (SOI) affects combustion phasing. As fuel reactivity is reduced, the ignition delay is increased and the combustion phasing is retarded. The longer ignition delay provides additional time for mixing, and reduces equivalence ratio stratification. Consequently, the premixed combustion is enhanced relative to diffusion combustion, and thus the soot emission is reduced. NO_x emission is also reduced due to reduced diffusion combustion and lower peak temperatures caused by delayed combustion phasing. An operability range is observed in terms of fuel reactivity and SOI, beyond which the mixture may not be sufficiently well mixed, or compression ignited. The study demonstrates the possibility of finding an optimum range of fuel reactivity, SOI, and EGR for significantly reducing engine out emissions for a given load and speed.     

Comparison of jatropha and karanja biofuels on their combustion characteristics

Biofuel blends produced from Jatropha (Jatropha curcas) and Karanja (Pongamia pinnata) oil were evaluated for their combustion properties. Two kinds of blends (regular diesel with Jatropha and Karanja oil) were prepared at 20% volume to the diesel and tested as alternative fuels in single cylinder (vertical), water-cooled, direct injection diesel engine at the rated speed of 1500 rpm. The performance of the engine in terms of thermal efficiency at full load for diesel was 30%. For Jatropha and Karanja biodiesel blends, the thermal efficiencies were 29.0% and 28.6%, respectively. The maximum cylinder pressure and ignition delay for biodiesel fuel blends are very close to that of regular diesel. Prolonged combustion was observed for Karanja oil blend in comparison to Jatropha oil blend. The combustion pattern also reveals the slow burning characteristics of vegetable oils and this study indicates that the blended biofuels have combustion characteristics that are similar to regular diesel fuels.     

Role of nano-additive blended biodiesel on emission characteristics of the research diesel engine

The current experimental study is aimed to analyze the influence of single-walled Carbon Nano Tubes (CNT) on the emission characteristics of neem biodiesel-fueled (NBD-fueled) diesel engine and the results compared with conventional diesel. Experiments were conducted in a single-cylinder, 4-stroke, diesel engine with an eddy current dynamometer at a constant speed of 1500 rpm. Two samples of CNT are characterized and dispersed into 100% of the NBD in a mass fraction of 50 and 100 ppm using ultrasonicator, and the physicochemical properties were measured. Experimental results indicated that by adding CNT nanoparticles in NBD reduces its NO_x, HC, CO, and smoke emission by 9.2%, 6.7%, 5.9%, and 7.8%, respectively, at all load conditions.     

Combustion features under different center of heat release of a diesel engine using dimethyl carbonate/diesel blend

Experiments were performed in a single cylinder common-rail diesel engine that adopts a low temperature premixed charge compression ignition (PCCI) mode. Combustion features of dimethyl carbonate (DMC)-diesel blends under various centers of heat release (COHRs) were revealed in details. With retarding of COHR, all the peaks of pressure and pressure rise rate and bulk gas temperature are postponed and declined in sequence. Normally, the crank angle of peak pressure is quite close to the COHR, while the peak of bulk gas temperature appears about 7°CA after COHR as a rule. The prolongation can be demonstrated at every stage of combustion such as q₁₀ and q₉₀ with the COHR being put backward. In addition, the heat release of diesel is completely slower than that of D10 fuel at various stages. Unfortunately, retarding of COHR implies a declining thermal efficiency of engines as well as a higher cyclic variation in general. Nevertheless, D10 blend has higher thermal efficiency than diesel thanks to high oxygen content of DMC and low boiling point that prompts better fuel atomization and complete combustion. Meanwhile, the cyclical variation of D10 is greater than diesel fuel owing to the low heat value, high latent heat of vaporization, and poor flammability of DMC. As a total, a comprehensive understanding of PCCI combustion features under different COHRs can be conducive to conducting effective management of combustion process and manipulating the subsequent emission performance to a favorable level.     

Effects of thermal barrier coating on the performance and combustion characteristics of a diesel engine fueled with biodiesel produced from waste frying cottonseed oil and ultra-low sulfur diesel

In this study, the top surfaces of piston and valves of a four-strokes and direct-injection diesel engine have been coated—with no change in the compression ratio—with a 100 μm of NiCrAl lining layer via plasma spray method and this layer has later been coated with main coating material with a mixture of 88% of ZrO₂, 4% of MgO and 8% of Al₂O₃ (400 μm). Then, after the engine-coating process, ultra-low sulfur diesel (ULSD) as base fuels and its blend with used frying cottonseed oil derived biodiesel in proportion of 20%, volumetrically, have been tested in the coated engine and data of combustion and performance characteristics on full load and at different speeds have been noted. The results, which were compared with those obtained by uncoated-engine operation, showed that thermal efficiency increased, and engine noise reduced. Cylinder gas pressure values obtained from the diesel engine which has been coated with thermal barriers have been found to be somewhat higher than those of the uncoated-engine. Also, maximum pressure values measured in both engines and under the same experimental conditions through the use of test fuel have been obtained after TDC. Moreover, heat release rate and heat release have occurred earlier in the coated-engine. NOx emissions were increased while CO and HC emissions were remained almost the same with a little bit decrease.     

Analysis of emission reduction in ethyne–biodiesel-aspirated diesel engine

The present experimental work investigates the use of ethyne gas in biodiesel-fueled diesel engine at different flow rate of 1, 2, and 3 L/min and is compared with diesel operation. This work is aimed to examine the outcome of ethyne gas by dual-fuel operation on emission characteristics of neat biodiesel-fueled stationary diesel engine. The oil derived from mustard seeds are employed as a source for biodiesel. The work was carried out at 2100 rpm (speed) and at an optimal compression ratio of 17. Based on the outcome of this investigation, the maximum reduction in hydrocarbon (25.1%), carbon monoxide (17.24%), and smoke emission (24.8%) was observed for biodiesel–ethyne at 3 L/min than the neat biodiesel. However, NO_x emissions were found to be 15.8% higher for ethyne–biodiesel fueling at 3 L/min owing to increase in combustion gas temperature than neat biodiesel.     

Impact of various blends of Mimusops elengi methyl esters on performance and emission characteristics of a diesel engine

The basic objective of the research work was to study the effect of various blends of Mimusops elangi methyl ester (MEME) on engine performance, combustion, and emission characteristics of a single-cylinder direct-injection compression ignition engine, running at constant speed. The raw oil was extracted from Mimusops elangi seeds through mechanical crusher. The neat MEME was obtained through transesterification process and mixed with diesel in versatile proportions of 10% of MEME (10% MEME–90% Diesel), 20% of MEME(20% MEME–80% Diesel), 30% of MEME(30% MEME–70% Diesel), 40% of MEME(40% MEME–60% Diesel), and 100% MEME on a volume basis. Their properties were validated based on ASTM standards. Experimental investigation revealed that the 20% blend resulted in 4.18%, 5.12% more prominent performance characteristics of brake thermal efficiency, brake specific energy consumption, and superior emission diminution of 5.26% of HC, 16.6% of CO, 6.2% of smoke when compared with base diesel fuel, despite marginal penalty of 5.26% of carbon dioxide and 4.8% of oxides of nitrogen emission at full load condition. Characteristics of combustion parameters like pressure inside the cylinder and rate of the heat released were superior for 20% blend of MEME at the peak load condition.     

Experimental investigation on the performance and emission characteristics of a diesel engine by varying the injection pressure and injection timing using mixed biodiesel

Biodiesel is a promising fuel for compression ignition engines instead of diesel fuel. Due to the depletion of diesel fuel, an alternative fuel can be used in an engine. The experiments were conducted on a four-stroke, single cylinder CI engine. In this present investigation, an attempt has been made to study the influence of injection pressure (IP) and injection timing (IT) on the performance and emission characteristics of diesel engines by using mixed biodiesel (Thevetia peruviana, Jatropha, Pongamia, and Azadirachta indica). The injection pressure is varied from 200 to 230 bar and the injection timing is varied from 23 to 29° bTDC at an increment of 10 bar and 2° bTDC, respectively, and the results were compared with diesel. From this study, the results showed that the brake thermal efficiency (BTE) was increased by 2.4% with an increase in injection pressure and 1.5% with an increase in the injection timing for the maximum load, but lesser than diesel. Furthermore, a reduction of 5.08% of brake specific fuel consumption (BSFC) has been noticed for the rise in IP and IT with loads but higher than diesel. The reduction was 34.17%, 53.85%, and 29.7% and 29.17%, 53.85%, and 21.95% of hydrocarbons (HC), carbon monoxide (CO), and smoke emissions, respectively, at 230 bar injection pressure and at 27° bTDC injection timing. Also, a significant increase in nitrogen oxides (NO_x) and carbon dioxide (CO₂) emissions at the maximum load was observed by increasing the injection pressure and injection timing.     

Experimental investigation on engine performances,combustion characteristics and emission of exhaust gases of VCR engine fuelled with cottonseed oil methyl ester blended with diesel

This research work investigates the engine performances, combustion characteristics, and emission of exhaust gases of variable compression ratio engine fuelled with cottonseed oil methyl ester (COME) and diesel at different blends. The analysis showed that heat release rate and cylinder pressure is higher for diesel than COME blends. Higher BTE is obtained at the maximum load condition. The higher BTE and lower SFC are obtained for blend B15 as 42.17% and 0.2 kg/kW-hr at brake mean effective pressure (BMEP) of 4.64 bar. Also it is found that the peak cylinder gas pressure and combustion duration increases when the BMEP increases. At the BMEP of 3.51 bar, higher HRR is observed as 18.12 J/deg. Increase in HRR is obtained as 6.07% for B30 at BMEP of 4.64 bar when compared to diesel. Ignition delay decreased by 13.16% for B100, by the increment of blend proportions when compared to diesel, at BMEP of 4.64 bar. Lower smoke, HC and CO emissions are observed when increasing the blend proportions, whereas the nitric oxide emissions increases due to the better combustion resulted in higher temperatures. At BMEP of 4.64 bar, the CO emissions are reduced to 25.24% for neat biodiesel when compared with the diesel.     

Emission study of a diesel engine fueled with higher alcohol-biodiesel blended fuels

This work examines the effect of butanol (higher alcohol) on the emission pattern of neat neem oil biodiesel (NBD100) fueled diesel engine. Single-cylinder, 4-stroke, research diesel engine was employed to conduct the trial. Blends comprising the mixture of biodiesel and higher alcohol were prepared by employing an ultrasonic agitator. Four test fuels such as neat neem oil biodiesel, diesel, and two blends of higher alcohol/neem oil biodiesel: 10% and 20% (by volume). Experimental result showed that increasing alcohol content to biodiesel brought down the various emissions such as Smoke, NO_x, HC, and CO by 6.8%, 10.4%, 8.6%, and 5.9%, respectively, at all loads. It was also concluded from the trail that a 20% higher alcohol/neem oil biodiesel blends show the promising signs in reducing all the emissions associated with biodiesel fuelled diesel engine.     

Verdant vehicles via viscoelasticity

The combustion of hydrocarbon (HC) fuels in internal combustion (IC) engines is modified by the presence of a few parts per million of megadalton molecular weight elastomers. The viscoelasticity imparted provides: reduced fuel vaporization, lesser back pressure, larger average droplet sizes, and lower combustion chamber temperatures. These effects result in: a reduction of emissions of HC, CO and NO_x of more than 70%, a substantial decrease in the number of particulates from diesel engines, a drop in combustion temperatures of more than 30vv°C, increases in engine power of more than 10%, an improved fuel octane rating, and economies of fuel consumption of more than 20%. The results are magnified during transitions, especially in the lower gears, used more often in urban traffic, where normal fuels emit more pollutants. These effects have a positive public health impact due to reductions in ozone, acid rain, particulates and partially oxidized HC.     

Investigation effect of hydrogen addition on the performance and exhaust emissions of Pongamia pinnata biodiesel fueled compression ignition engine

In the recent decades, the energy demand for transport and industrial sector has increased considerably. Fossil fuels which were the major fuel source for decades are no more sustainable. Biodiesel is an efficient alternative compared to depleting fossil fuels. The prospect of biodiesel as the best alternative fuel is a reliable source compared to depleting fossil fuels. Hydrogen is also considered as an attractive alternative fuel producing low emission with improved engine performance. This paper investigates the performance and emission characteristics of a single cylinder compression ignition engine using hydrogen as an inducted fuel and biodiesel, aka Pongamia pinnata as injected fuel. The experiments are conducted for different quantities of hydrogen induction through the intake manifold in order to improve the performance of the engine. The performance parameters such as brake thermal efficiency, brake specific fuel consumption, exhaust temperature and emission quantities like HC, NO_X, CO, CO₂ of biodiesel fueled CI engine with variable mass flow rate of hydrogen are investigated. The performances of biodiesel combined with hydrogen at varying mass flow rates are also compared. The 10 LPM hydrogen induction with biodiesel provided 0.33% increase of brake thermal efficiency compared with diesel and increase of 3.24% to biodiesel at 80% loading conditions. The emission of HC decreased by 13 ppm, CO decreased by 0.02% by volume and CO₂ decreased by 3.8% by volume for biodiesel with induction of hydrogen at 10 LPM to that of neat biodiesel for 80% load conditions.     

Performance evaluation and emission characteristics of biodiesel-ignition enhancer blends propelled in a research diesel engine

This study details the effect of the Di-Methyl-Ether(DME) as a cetane improver on neat cashew nut shell biodiesel (CBD100) to assess the emission and performance engine characteristics. Four fuels, namely, diesel, biodiesel (Cashew nut shell Methyl Ester), a blend of CBD100-10% and 20% by volume of DME (CBD90DME10and CBD80DME20) are prepared and tested on a stationary research diesel engine. The experimental parameters for CBD80DME20 showed a 1.6% increase in thermal efficiency thereby reducing 4.1% of fuel consumption than the neat biodiesel at peak conditions. Experimental result exposed that 20% of DME reduces 3.4% CO, 4.2% HC and 8.8% NOx and 8.4% smoke emissions of CBD100. Based on the outcome of this work, it is clear that CBD80DME20 shall be employed as a substitute fuel for diesel engine.

Abbreviations: CI: Compression ignition; CBD100: Cashew nut shell Bio-diesel; DME: Di-methyl ether; CO: Carbon monoxide; BTE: Brake thermal efficiency; BSFC: Brake specific fuel consumption; CBD100: 100% Biodiesel; CBD90DME10: 90% biodiesel + 10% di-methyl-ether; CBD80DME20: 80% biodiesel + 20% di-methyl-ether; HC: Hydrocarbon; NO_x: Oxides of nitrogen.     

Processing of Straw/Corn Stover: Comparison of Life Cycle Emissions

The LCA emissions from four renewable energy routes that convert straw/corn stover into usable energy are examined. The conversion options studied are ethanol by fermentation, syndiesel by oxygen gasification followed by Fischer Tropsch synthesis, and electricity by either direct combustion or biomass integrated gasification and combined cycle (BIGCC). The greenhouse gas (GHG) emissions of these four options are evaluated, drawing on a range of studies, and compared to the conventional technology they would replace in a western North American setting. The net avoided GHG emissions for the four energy conversion processes calculated relative to a “business as usual” case are 830 g CO₂e/kWh for direct combustion, 839 g CO₂e/kWh for BIGCC, 2,060 g CO₂e/L for ethanol production, and 2,440 g CO₂e/L for FT synthesis of syndiesel. The largest impact on avoided emissions arises from substitution of biomass for fossil fuel. Relative to this, the impact of emissions from processing of fossil fuel, e.g., refining of oil to produce gasoline or diesel, and processing of biomass to produce electricity or transportation fuels, is minor.