Airborne bacterial reduction by spraying slightly acidic electrolyzed water in a laying-hen house

Spraying slightly acidic electrolyzed water (SAEW) has been considered as a potential approach to reduce airborne bacteria in laying-hen houses. In this study, the effects of spraying SAEW on airborne bacterial reduction were investigated in a laying-hen house as compared with using diluted didecyl dimethyl ammonium bromide (DDAB). Averaged air temperature reduced by approximate 1 °C and average relative humidity increased by 3% at a stable ventilation rate (about 2.5 m³ hr^?1 per bird) in the laying-hen house 30 min after spraying (120 mL m^?2). Compared with the control without spraying, the airborne bacterial concentration was reduced by about 0.70 and 0.37 log₁₀ colony-forming units (CFU) m^?3 in the 4 hr after spraying 120 mL m^?2 SAEW (available chlorine concentration [ACC] of 156 mg L^?1) and diluted DDAB (active compound concentration of 167 mg L^?1), respectively. Compared with spraying diluted DDAB, spraying SAEW was determined to be more effective for reducing airborne bacterial in laying-hen houses. The effects of spraying SAEW and diluted DDAB on airborne bacterial reduction in the laying-hen house increased with the increasing available chlorine concentrations for SAEW (156, 206, 262 mg L^?1) and increasing active compound concentrations for diluted DDAB (167, 333, 500 mg L^?1), respectively. Spraying SAEW and diluted DDAB with two levels of spraying volumes (120 and 90 mL m^?2) both showed significant differences on airborne bacterial reduction in the laying-hen house (P < 0.05).

Implications: It is difficult to effectively reduce airborne bacteria in laying-hen houses. This work describes the application of spraying slightly acidic electrolyzed water as a new approach for reducing airborne bacteria in a laying-hen house. The effects of active compound concentrations and spray volumes on the airborne bacterial reductions by spraying SAEW were also investigated. This study provided a new effective and environmentally friendly approach to reduce the airborne bacteria in poultry houses, contributing to bird housing environment management and improving bird health.     

电渗透脱水对污泥热干燥特性的影响

以污水厂机械脱水后的污泥作为研究对象,提出了采用电渗透-热干燥结合进行深度脱水的方法。通过对原泥以及电渗透脱水至不同含水率(67%、71%和76%)的污泥在热干燥过程中含水率和干燥速率的测定,分析电渗透脱水对污泥热干燥特性的改善规律。结果表明,经电渗透脱水至含水率为67%和71%的污泥在热干燥过程中的传热传质速率及干燥速率有明显提高,且干燥温度越高,电渗透后污泥的干燥速率与原泥的干燥速率差距越大。相同电压梯度及相同温度下电渗透至67%后进行热干燥耗能最少。实际应用中应结合能耗分析选择合适的电渗透程度及干燥温度,以达到最优效果。     

Microwave enhanced advanced oxidation treatment of dairy manure

Abstract

The microwave enhanced advanced oxidation process (MW-AOP) was used to treat dairy manure in a continuous-flow 915?MHz microwave wastewater treatment system. The treatment efficiency increased with an increase in temperature, as well as hydrogen peroxide dosage. The settling property was also improved in all treated sets, regardless of temperature applied. The system operated at temperatures >100?°C had a much higher soluble chemical oxygen demand than at temperatures <100?°C. The highest soluble carbonaceous compounds, orthophosphate and ammonia were obtained at 110?°C and 0.6%H₂O₂ per % of total solids content. The process should be operated at higher temperatures and higher hydrogen peroxide dosages for maximizing solids disintegration, nutrient release and energy efficiency. An energy fingerprint correlating the cumulative energy consumption and temperature rise was developed. The results demonstrated that the custom designed MW-AOP system is suitable for the effective treatment of dairy manure. The system can readily be scaled up and integrated into a dairy farm manure treatment and resource recovery system.     

Anaerobic digestion of livestock and poultry manures spiked with tetracycline antibiotics

Abstract

We investigated the anaerobic degradation of tetracycline antibiotics (tetracycline [TC], oxytetracycline [OTC] and chlortetracycline [CTC]) in swine, cattle, and poultry manures. The manures were anaerobically digested inside polyvinyl chloride batch reactors for 64?days at room temperature. The degradation rate constants and half-lives of the parent tetracyclines were determined following first-order kinetics. For CTC the fastest degradation rate was observed in swine manure (k?=?0.016?±?0.001 d^?1; half-life = 42.8?days), while the slowest degradation rate was observed in poultry litter (k?=?0.0043?±?0.001 d^?1; half-life = 161?days). The half-lives of OTC ranged between 88.9 (cattle manure) and 99.0?days (poultry litter), while TC persisted the longest of the tetracycline antibiotics studied with half-lives ranging from 92.4?days (cattle manure) to 330?days (swine manure). In general, the tetracyclines were found to degrade faster in cattle manure, which had the lowest concentrations of organic matter and metals as compared to swine and poultry manures. Our results demonstrate that tetracycline antibiotics persist in the animal manure after anaerobic digestion, which can potentially lead to emergence and persistence of antibiotic resistant bacteria in the environment when anaerobic digestion byproducts are land applied for crop production.     

湿污泥在流化床中干燥特性

在鼓泡流化床干燥器内,床料采用0～1 mm的石英砂,以热空气作为干燥介质,对城市污水污泥的流态化干燥特性进行实验研究。通过控制送风温度、流化风量、加料量、污泥粒径等参数,研究在不同工况条件下床温以及干污泥含水率的变化情况。结果表明,随着送风温度的升高,床温升高,干污泥含水率下降,最终趋向于一个稳定值8%。床温随流化风量的增加先是减小而后升高,干污泥的含水率随流化风量的增加先是降低而后增大。当加料量从11 kg/h增加到13kg/h时,干污泥的含水率基本没有变化,当加料量超过13 kg/h时,干污泥的含水率从8.1%开始呈递增趋势。随污泥粒径的增大,床温升高,干污泥含水率也随之升高。     

Effect of Fractionation and Pyrolysis on Fuel Properties of Poultry Litter

Abstract

Raw poultry litter has certain drawbacks for energy production such as high ash and moisture content, a corrosive nature, and low heating values. A combined solution to utilization of raw poultry litter may involve fractionation and pyrolysis. Fractionation divides poultry litter into a fine, nutrient-rich fraction and a coarse, carbon-dense fraction. Pyrolysis of the coarse fraction would remove the corrosive volatiles as bio-oil, leaving clean char. This paper presents the effect of fractionation and pyrolysis process parameters on the calorific value of char and on the characterization of bio-oil. Poultry litter samples collected from three commercial poultry farms were divided into 10 treatments that included 2 controls (raw poultry litter and its coarse fraction having particle size greater than 0.85 mm) and 8 other treatments that were combinations of three factors: type (raw poultry litter or its coarse fraction), heating rate (30 or 10 °C/min), and pyrolysis temperature (300 or 500 °C). After the screening process, the poultry litter samples were dried and pyrolyzed in a batch reactor under nitrogen atmosphere and char and condensate yields were recorded. The condensate was separated into three fractions on the basis of their density: heavy, medium, and light phase. Calorific value and proximate and nutrient analysis were performed for char, condensate, and feedstock. Results show that the char with the highest calorific value (17.39 ± 1.37 MJ/kg) was made from the coarse fraction at 300 °C, which captured 68.71 ± 9.37% of the feedstock energy. The char produced at 300 °C had 42 ± 11 mg/kg arsenic content but no mercury. Almost all of the Al, Ca, Fe, K, Mg, Na, and P remained in the char. The pyrolysis process reduced ammoniacal-nitrogen (NH₄-N) in char by 99.14 ± 0.47% and nitrate-nitrogen (NO₃-N) by 95.79 ± 5.45% at 500 °C.     

Partitioning of formaldehyde between air and ice at −35°C to −5°C

The equilibrium partitioning of formaldehyde (HCHO) between air and snow was studied in a series of laboratory experiments conducted at −5°C, −15°C, and −35°C, in order to understand how partitioning of HCHO between air and polar snow varies with temperature, and thus seasonally on the ice sheet. Measured partitioning coefficients were 56, 93, and 245 mol l⁻¹ atm⁻¹ for −5°C, −15°C and −35°C, respectively, showing a similar trend as the values previously estimated from field observations. Estimates of the pseudo-first-order rate coefficient for air–snow exchange for the same three temperatures were 4.1×10⁻⁴, 1.1×10⁻⁴, and 1.1×10⁻⁵ s⁻¹, respectively. This implies a time scale for air–snow equilibration of the order of hours to days for HCHO accumulated at or near the ice–air interface on snow grains. Comparing the current laboratory partitioning coefficients with those estimated from measurements of air and freshly fallen snow in Greenland during summer demonstrates that the snow is supersaturated and should degas HCHO to the surrounding air. During this degassing, polar snow should be a significant source of HCHO to the lower troposphere.     

电渗透脱水污泥干燥特性曲线及干燥模型

通过电渗透脱水技术及自然风干技术两种预处理方式降低污泥含水率,当污泥初始含水率相近时,研究经两种方式处理后污泥的干燥特性曲线,并对电渗透脱水污泥干燥特性曲线的优势情况进行探讨。在40—120℃的低温条件下,研究电渗透脱水污泥（泥饼厚度为3．5mm）的干燥特性曲线并分析其干燥特性。通过所得电渗透脱水污泥的干燥特性曲线,引人薄层污泥干燥模型进行数值分析。结果表明,在实验条件下,电渗透脱水污泥的干燥速率要优于自然风干污泥的干燥速率。随着温度的升高,电渗透脱水污泥的干燥速率随之升高,干燥到所需含水率的时间则随之减少。Logarithmic模型比其他模型更适合描述薄层电渗透脱水污泥在低温条件下的干燥特性。     

Effect of fipronil on biogas production performance during anaerobic digestion of chicken manure and corn straw

Fipronil is a broad-spectrum insecticide that has a good control effect on pests of commercial poultry. Although many studies have reported the environmental fate of fipronil, the influence of residual fipronil in poultry waste on biogas production has not been further explored yet. In this article, an experimental comparative study on anaerobic digestion (AD) of chicken manure (CM) and corn straw (CS) with different fipronil concentrations (FCs) was carried at 8% of total solid (TS) and mid-temperature (35?±?1)°C. The results showed that fipronil had a significant effect on biogas production during AD of CM and CS. When the FC is at a low level (≤10?mg·kg^?1), the biogas production rate is increased and the digestion period was shortened, while higher FC (≥ 20?mg·kg^?1) showed an inhibitory effect. During the monitoring of enzyme activity, low FC showed no significant effect on cellulase and saccharase, but the urease activity increased in the early stage. High FC showed inhibition of activity of cellulase and urease, but the saccharase activity was significantly inhibited until FC reached 40?mg·kg^?1. This study also confirms that the environment in anaerobic digester is favorable for the degradation of fipronil, and its half-life is about 15.83?days.     

Impact of anthropogenic heat on urban climate in Tokyo

This study quantifies the contribution through energy consumption, to the heat island phenomena and discussed how reductions in energy consumption could mitigate impacts on the urban thermal environment. Very detailed maps of anthropogenic heat in Tokyo were drawn with data from energy statistics and a very detailed digital geographic land use data set including the number of stories of building at each grid point. Animated computer graphics of the annual and diurnal variability in Tokyo's anthropogenic heat were also prepared with the same data sources. These outputs characterize scenarios of anthropogenic heat emission and can be applied to a numerical simulation model of the local climate. The anthropogenic heat flux in central Tokyo exceeded 400 W m⁻² in daytime, and the maximum value was 1590 W m⁻² in winter. The hot water supply in offices and hotels contributed 51% of this 1590 W m⁻². The anthropogenic heat flux from the household sector in the suburbs reached about 30 W m⁻² at night. Numerical simulations of urban climate in Tokyo were performed by referring to these maps. A heat island appeared evident in winter because of weakness of the sea breeze from Tokyo Bay. At 8 p.m., several peaks of high-temperature appeared, around Otemachi, Shinjuku and Ikebukuro; the areas with the largest anthropogenic heat fluxes. In summer the shortwave radiation was strong and the influence of anthropogenic heat was relatively small. In winter, on the other hand, the shortwave radiation was weak and the influence of anthropogenic heat was relatively large. The effects of reducing energy consumption, by 50% for hot water supply and 100% for space cooling, on near surface air temperature would be at most −0.5°C.     

Bioenergy production from diluted poultry manure and microbial consortium inside Anaerobic Sludge Bed Reactor at sub-mesophilic conditions

In this study, anaerobic treatability of diluted chicken manure (with an influent feed ratio of 1 kg of fresh chicken manure to 6 L of tap water) was investigated in a lab-scale anaerobic sludge bed (ASB) reactor inoculated with granular seed sludge. The ASB reactor was operated at ambient temperature (17–25°C) in order to avoid the need of external heating up to higher operating temperatures (e.g., up to 35°C for mesophilic digestion). Since heat requirement for raising the temperature of incoming feed for digestion is eliminated, energy recovery from anaerobic treatment of chicken manure could be realized with less operating costs. Average biogas production rates were calculated ca. 210 and 242 L per kg of organic matter removed from the ASB reactor at average hydraulic retention times (HRTs) of 13 and 8.6 days, respectively. Moreover, average chemical oxygen demand (COD) removal of ca. 89% was observed with suspended solids removal more than 97% from the effluent of the ASB reactor. Influent ammonia, on the other hand, did not indicate any free ammonia inhibition due to dilution of the raw manure while pH and alkalinity results showed stability during the study. Microbial quantification results indicated that as the number of bacterial community decreased, the amount of Archaea increased through the effective digestion volume of the ASB reactor. Moreover, the number of methanogens displayed an uptrend like archaeal community and a strong correlation (?0.645) was found between methanogenic community and volatile fatty acid (VFA) concentration especially acetate.     

城市污泥微波干化工艺及干化特性研究

采用微波和烘箱结合及全程烘箱2种方式对城市污泥干化进行对比研究,考察了不同粒径、微波干化预处理、预处理时间及烘箱温度对污泥干燥特性的影响。结果表明,同一温度条件下,微波预处理时间越长,污泥干化速率越快。最优条件下,全程烘箱污泥达到最大干化速率的含水率为77%。微波干燥污泥具有时间短、干燥速率大的特点,微波和烘箱结合对比全程烘箱干化速率高且能耗低。     

Influence of the inlet air in efficiency of photocatalytic devices for mineralization of VOCs in air-conditioning installations

Nowadays, a large proportion of photocatalytic oxidation (PCO) devices are being implemented in heating, ventilation and air-conditioning systems. However, no systematic studies have been carried out regarding the influence of inlet air preconditioning. To analyse the impact of the inlet air-conditions into photocatalytic efficiency, a simulated air-conditioning duct with flowing gas through inside was designed. Isobutylene was chosen as the target VOCs. The concentration in the gas phase was monitored using a photoionization detector. The influence of flow rate, relative humidity and temperature on the VOC removal efficiency was analysed. Experimental results were presented in terms of gas-removal efficiency (η) and clean air delivery rate (CADR) and analysed on a kinetic basis. From them, the weight of each parameter in the global process has been determined, from bigger to smaller contribution, flow>>temperature>relative humidity. Also, the relevance of the inlet air conditions has been illustrated in a model room in order to determinate the time necessary to obtain a threshold value accomplishing with enough air quality and the energy consumption of the device. Additionally, the photocatalytic decontamination has been assimilated to the “air exchange rate”, a parameter commonly used in indoor air quality studies. The results show that preconditioning of air can improve the efficiency of photocatalytic devices and bring important energy savings.     

The Autothermal Pyrolysis of Waste Tires

Abstract

The growing amount of rubber waste, such as that from tires and cables, has resulted in serious environmental problems. Since rubber waste is not easily biodegradable even after a long period of landfill treatment, material and energy recovery is the preferable alternative to disposal. The potential offered by waste tire pyrolysis for solving both energy and waste treatment problems is widely recognized. Pyrolysis is one method of inducing thermal decomposition without using any oxidizing agent, or using such a limited supply of the agent that oxidization does not proceed to an appreciable extent. The latter may be described as autothermal pyrolysis and will be studied in the present work.

The main objective of this research was to study the operating parameters of autothermal pyrolysis of scrap tires in a laboratory-scale fluidized bed reactor with a 100-cm bed height (10 cm I.D.) and a 100-cm freeboard (25 cm I.D.). Scrap tires were pyrolyzed in a limited oxygen supply, so that the heat for pyrolysis of the scrap tires was provided by combustion of some portion of the scrap tires. The operating parameters evaluated included the effect on the pyrolysis oil products and their relative proportions of (1) the air factor (O.O7–O35); (2) the pyrolysis temperature (370–570 °C); and (3) the catalyst added (zeolite and calcium carbonate). The results show that: (1) the composition of the liquid hydrocarbon obtained is affected significantly by the air factor; (2) the higher operating temperature caused a higher yield of gasoline and diesel; (3) the yield of gasoline increased due to the catalyst zeolite added, and the yield of diesel increased due to the addition of the catalyst calcium carbonate; (4) the principal constituents of gasoline included dipentene and diprene.     

Tools For Evaluating New Process and Control Plans

The purpose of this paper on industrial plan evaluation is twofold: to present tools which can be used to evaluate quantitatively certain aspects of air pollution control devices, and to point up specifically two areas in which research is urgently needed. These research areas are in removing solid particles after wetting in scrubbers and use of surface active agents in scrubbing gaseous pollutants. Therefore, the body of information presented is directed to engineers in the field of evaluating the air pollution potential of new industrial plants, to scientists involved in determining the parameters and effectiveness of control devices, and to research and development scientists in the field of surfactants.

One tool presented is a chart for measuring the effectiveness of incinerator afterburners and vapor incinerators. The required inputs to the chart are the rate of flue gas flow in standard cubic feet per minute and the auxiliary fuel burner capacity in Btu per hour. The chart yields the flue gas temperature increase which will result, given in degrees F. The second tool presented is a new psychrometric graph for the humidifying and cooling of gases from processes as hot as 3000°F. Inputs into the graph are the temperature of the gases entering the sprays from the hot process and the temperature desired before they enter a control device such as a fabric filter or a scrubber. The chart yield is the amount of water needed in gallons per thousand cubic feet of gas. The only calculation needed is a correction of the hot gas volume to 70°F. Water needed to saturate the gases can be read directly also.     

Development of functional composts using spent coffee grounds,poultry manure and biochar through microbial bioaugmentation

Spent coffee grounds (SCG), poultry manure, and agricultural waste-derived biochar were used to manufacture functional composts through microbial bioaugmentation. The highest yield of tomato stalk-based biochar (40.7%) was obtained at 450°C with a surface area of 2.35 m² g^?1. Four pilot-scale composting reactors were established to perform composting for 45 days. The ratios of NH₄⁺–N/NO₃^?–N, which served as an indicator of compost maturity, indicate rapid, and successful composting via microbial bioaugmentation and biochar amendment. Moreover, germination indices for radish also increased by 14–34% through augmentation and biochar amendment. Microbial diversity was also enhanced in the augmented and biochar-amended composts by 7.1–8.9%, where two species of Sphingobacteriaceae were dominant (29–43%). The scavenging activities of 2,2-diphenyl-1-picrylhydrazyl (DPPH) were enhanced by 14.1% and 8.6% in the fruits of pepper plants grown in the presence of the TR-2 (augmentation applied only) and TR-3 (both augmentation and biochar amendment applied) composts, respectively. Total phenolic content was also enhanced by 68% in the fruits of the crops grown in TR-3. Moreover, the other compost, TR-L (augmentation applied only), boosted DPPH scavenging activity by 111% in leeks compared with commercial organic fertilizer, while TR-3 increased the phenolic content by 44.8%. Composting facilitated by microbial augmentation and biochar amendment shortened the composting time and enhanced the quality of the functional compost. These results indicate that functional compost has great potential to compete with commercially available organic fertilizers and that the novel composting technology could significantly contribute to the eco-friendly recycling of organic wastes such as spent coffee grounds, poultry manure, and agricultural wastes.     

Energy Consumption Requirements for Air Pollution Control Equipment at An Iron Foundry

Energy consumption requirements for air pollution control equipment were studied for varying removal efficiency levels at the Tyler Pipe Industries iron foundry in Tyler, Texas, based on plant fuel consumption data, and on field test measurements of cupola carbon monoxide and particulate control equipment. Natural gas consumption for CO removal increased from 0 in 1970 to 25.4% of the plant total in 1976. Operating costs to achieve 85% CO control increased from 0 in 1970 to $1.61/ton metal in 1976. Increasing cupola incinerator temperature from 800° to 1600° F increased CO removal efficiency from 60 to 97%, but also increased natural gas consumption by 150%. Electricity consumption requirements for 95% to 97% particulate control at the foundry increased from 0.1 % of plant total in 1970 to 18.7% in 1976. Electricity consumption for particulate controls increased plant operating costs from 0.004 in 1970 to 1.693 $/ton metal in 1976 as horsepower increased from 20 to 6,272. Cost-benefit methodology is needed to evaluate trade-offs between air pollution control, energy consumption requirements and operating costs of proposed regulations. Total air pollution control system must be considered in enforcing regulations instead of the source to be controlled alone for overall impacts. Need exists for process modifications to enhance energy recovery and development of energy-effective air pollution control equipment.     

Carbon dioxide and methane emissions from the scale model of open dairy lots

To investigate the impacts of major factors on carbon loss via gaseous emissions, carbon dioxide (CO₂) and methane (CH₄) emissions from the ground of open dairy lots were tested by a scale model experiment at various air temperatures (15, 25, and 35 °C), surface velocities (0.4, 0.7, 1.0, and 1.2 m sec^?1), and floor types (unpaved soil floor and brick-paved floor) in controlled laboratory conditions using the wind tunnel method. Generally, CO₂ and CH₄ emissions were significantly enhanced with the increase of air temperature and velocity (P < 0.05). Floor type had different effects on the CO₂ and CH₄ emissions, which were also affected by air temperature and soil characteristics of the floor. Although different patterns were observed on CH₄ emission from the soil and brick floors at different air temperature-velocity combinations, statistical analysis showed no significant difference in CH₄ emissions from different floors (P > 0.05). For CO₂, similar emissions were found from the soil and brick floors at 15 and 25 °C, whereas higher rates were detected from the brick floor at 35 °C (P < 0.05). Results showed that CH₄ emission from the scale model was exponentially related to CO₂ flux, which might be helpful in CH₄ emission estimation from manure management.

Implications: Gaseous emissions from the open lots are largely dependent on outdoor climate, floor systems, and management practices, which are quite different from those indoors. This study assessed the effects of floor types and air velocities on CO₂ and CH₄ emissions from the open dairy lots at various temperatures by a wind tunnel. It provided some valuable information for decision-making and further studies on gaseous emissions from open lots.     

Biodegradation of α and β Endosulfan in Soil as Influenced by Application of Different Organic Materials

Abstract

A laboratory pot experiment was conducted to study the effect of amending soil with four different sources of organic matter on the degradation rate of α and β endosulfan isomers. Poultry by-product meal, poultry manure, dairy manure, and municipal solid waste compost were cured, dried, ground (<1 mm) and thoroughly mixed with a calcareous soil at a rate of 2% and placed in plastic pots. Endosulfan was added at the rate of 20 mg kg^?1. The moisture level was kept near field capacity and the pots were kept at room temperature. Soil sub-samples, 100 g each, were collected from every pot at days 1, 8, 15, 22, 29, 43, and 57 for the measurement of endosulfan isomers. Endosulfan residues were extracted from the soil samples with acetone. The supernatant was filtered through anhydrous sodium sulphate, 5 mL aliquot was diluted to 25 mL with hexane, mixed well, and then two sub-samples from the filtrates were analyzed for α and β endosulfan isomers by gas chromatography. The results indicated that the half-life (T _½) of α-endosulfan in the poultry by-product meal treatment was 15 days compared to about 22 days in the other treatments. The T _½ of β-endosulfan was 22 days in the poultry by-product meal treatment and followed a bi-phasic pattern, 57 days in the municipal solid waste compost treatment and the extrapolated T _½ was about 115 days for the other three treatments.     

低压供气式射流器工业化性能研究

简要介绍了低压供气式射流器的工作原理和作用,对其在氧化沟污水处理工艺中的氧利用率和动力效率等因素做了测试和分析,比较了不同水深对充氧性能的影响。结果表明,低压供气式射流曝气器氧利用率达23.17%,动力效率达2.43 kg O2/(kW.h),优于其他形式的曝气设备,可以有效降低能耗。