离子色谱—电化学检测法测定溴和碘

用离子色谱-电化学检测法同时测定溴和碘。以0.025mol/ L硝酸钠为淋洗液,其酸度为pH6.0.施加电压为+0.2V,对测定溴和碘量为适宜。方法可用于天然水中μg/L级溴和碘的测定。溴和碘的最低检测限各为0.4、1.0μg/L。当溴浓度为3.2μg/L,碘浓度为62μg/L时,变异系数各为3.4％及1.8％。     

离子色谱法测定水中溴离子与碘离子

采用离子色谱法测定水中溴离子与碘离子,选择AS19阴离子交换分离柱、KOH淋洗液自动发生器、抑制型电导检测。溴离子与碘离子分别在14.8 μg/L～100 mg/L与30.4 μg/L～100 mg/L范围内线性良好,检出限分别为3.7 μg/L与7.6 μg/L,环境水样平行测定的RSD分别为0.2%～1.5%与0.3%～1.6%,两个质量浓度水平的加标回收率分别为91.8%～105%与89.5%～93.4%。     

离子选择电极测定氟常见的问题

氟离子选择电极测定任何样品中的氟,从绘制标准曲线至整批样品测定,清洗电极的电位必须前后一致,否则将产生较大的误差,对测量仪器的要求一般电极电位要精确到０．１ｍＶ至少达到１ｍＶ。     

地下饮用水中良量NO^—2的催化动力学法测定

报道了一种新的测定NO^-2的高选择性和高灵敏度的催化光度分析法。基于H3PO4介质中,碘绿与溴酸钾的氧化还原反应受亚硝酸盐的催化使碘 绿褪色,据此建立了测定NO^-2的新方法。本文法检出限为0.29ug/L,该方法用于地下饮用水、环境标样的测定,相对标准为偏差 为1.05%-4.80% ,加标回收率为95％－117％。     

离子色谱-三重四级杆质谱法测定生活饮用水中痕量碘乙酸

水样经MAX固相萃取小柱富集后,用体积分数为1%的甲酸-甲醇溶液洗脱,洗脱液经0.22 μm滤膜过滤,在离子色谱柱上分离后采用三重四级杆质谱法测定水样中的碘乙酸。该方法在0 μg/L~1 000 μg/L范围内线性良好,方法检出限为0.3 μg/L。生活饮用水样品3个质量浓度水平的加标回收率为94.0%~106%,5次测定结果的RSD为2.1%~5.3%。将该方法用于测定江苏地区生活饮用水,结果未检出,高碘地区原水的加氯模拟消毒试验测得消毒后水样中碘乙酸为1.3 μg/L。     

山东单县浅层高氟高碘地下水的水化学特征及成因分析

氟和碘作为人体必需的微量元素,过少或过多摄入都会影响人身健康,相较于缺氟、缺碘,高氟高碘地下水对人体的危害更加难以控制。该研究选择单县作为典型的水源型高氟高碘地区,通过对浅层高氟高碘地下水进行采样测试,采用箱线图、Piper图及双变量相关性分析等多元统计技术剖析了该区域浅层地下水的水环境特征;采用R型因子分析揭示了水化学成分之间的相互关系,探讨了该区浅层高氟高碘地下水的成因。结果表明:①单县浅层地下水中的氟化物和碘化物的质量浓度均值分别为1.2 mg/L和391 μg/L。②随着氟化物浓度的增加,水化学类型偏向于向HCO₃-Na型和HCO₃-Na·Mg型集中,而随着碘化物浓度的增加,水化学类型则倾向于以HCO₃-Na·Mg为主。③该区域强烈的蒸发浓缩作用是控制单县浅层地下水化学成分的最重要因子;萤石平衡控制作用是控制单县浅层地下水高氟背景的因子;水-有机沉积物相互作用是控制单县浅层地下水高碘背景的因子。     

磷酸—磷酸氢二钠法测定尿、血液中的碘元素

尿、血液中碘的测定前处理方法很多,本法用磷酸—磷酸氢二钠离子强度缓冲液加抗坏血酸分解样品,无需分离,在ｐＨ２的条件下用碘离子选择电极直接浓度直读法测定尿、血液中的碘。本法检出限为１０μｇ·ｍｌ－１,标准偏差为０３５０μｇ·ｍｌ－１,精密度为３５８％,具有简便、快速等特点。     

气相分子吸收光谱法测定海水中氨氮的干扰因素识别及预处理方法研究

采用气相分子吸收光谱法测定海水样品中的氨氮,重点考察海水中共存离子对氨氮测定结果的影响规律,识别测定过程中主要的干扰因素,并提出消除干扰的预处理方法.研究结果表明,碘离子会对氨氮的测定产生负干扰,当样品中碘离子质量浓度达到0.0765 g/L时,氨氮的测定结果与标准值相比明显降低,且在碘离子质量浓度达到0.1910 g...     

离子选择电极法测定水中氟化物的注意事项

离子选择电极法测定水中氟化物应注意的事项。1　空白电位值电极在使用前必须在 1 0 - 3 ｍｏｌ/ＬＮａＦ溶液中浸泡 1ｈ～ 2ｈ进行活化 ,再用去离子水反复清洗 ,直至空白电位值达 +2 70ｍＶ左右。氟电极使用一段时间后就很难达到 +2 70ｍＶ空白电位值 ,这是由于电极头部敏感部分受到油类污染所致 ,采用酒精浸泡再用现制的去离子水洗涤处理 ,可使空白电位值恢复到 +2 70ｍＶ左右。这里还要注意清洗电极和绘制校准曲线以及样品测量时应使用同一种水质的去离子水 ,以避免因水质不同所引起的测量误差。2　温度温度对测量结果的影响很大 ,当温度…     

滤膜氟离子选择电极法测定大气中氟化物的改进

通过对国标方法中标准溶液系列的配制、样品滤膜处理方法进行研究,改进滤膜采样氟离子选择电极法测定大气中氟化物的实验方法,并利用改进方法对大气样品和氟化物标准样品进行对比实验。结果表明,标准样品的标准偏差为0.010~0.019 mg/L,相对标准偏差为3.0%~3.2%;大气样品的标准偏差为0.058~0.12μg/m3,相对标准偏差为4.2%~4.5%,加标回收率在95%~105%之间,满足国家标准的要求。     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.     

Hydrocarbon Utilization in Yeast Isolates Found to Grow in Association with Petroleum in a Polluted Ultisol of Midwestern Nigeria

The population counts of hydrocarbon-utilising yeasts weremonitored at six sampling stations in the Benin City municipalarea over a four-week period. Although the population countswere relatively constant in each locality, the highest countsoccurred in areas heavily polluted by domestic and industrialeffluents. A total of thirty-five hydrocarbon-degrading yeastswere isolated from soil at the sampling stations usingn-hexadecane as sole carbon source. The isolates were identifiedas belonging to the genera Candida (27 strains), Endomycopsis (4 strains). All the organisms grew on long-chainn-alkane, kerosene, diesel oil and crude oil but failed to growon short-chain n-alkane, aromatic and alicyclic hydrocarbons.Measurement of growth attributes of the isolates usingn-hexadecane, diesel oil and crude oil as substrates showed thatthe Candida species were better utilizers of hydrocarbonsubstrates relative to Endomycopsis and Schizosaccharomyces species.     

Hydrologic–Economic Model for Managing Irrigation Intensity in Irrigation Areas under Watertable and Soil Salinity Targets

This paper gives mathematical details and sample applications of SWAGMAN Farm (SWAGMAN, Salt Water and Groundwater Management), a farm-scale hydrologic economic model that integrates agronomic, climatic, irrigation, hydrogeological and economic aspects of irrigated agriculture. The model is capable of determining optimum mix of land use to keep watertable and soil salinity within acceptable limits while maximising the economic returns. Alternatively, the model can simulate water and salt balance and economics of a given cropping preference. Web-based and Geographic Information Systems versions of the model are available for integration with the environmental reporting systems of the irrigation areas.     

火焰原子吸收光谱法测定苏州开发区26种蔬菜中铜锌铁锰镍

用火焰原子吸收光谱法测定了苏州开发区26种蔬菜中的铜、锌、铁、锰和镍的含量。蔬菜样品用硝酸高氯酸混合酸进行消解。4次测定值的相对标准差<5%,加标回收率在92%～107%之间。26种蔬菜中铜、锌、铁、锰、镍的含量基本均在世贸组织规定的范围内。     

Using Multiple Taxonomic Groups to Index the Ecological Condition of Lakes

Biological indicators of communitiestypically reflect a common environmental signalreflecting the general condition of the ecosystem, as well asindividual signals by indicators differentiallysensitive to particular environmental conditions. Wedescribe here a method of integrating and interpretingsuch indicators from 19 New England lakes for fivetaxonomic groups (diatoms, benthos, zooplankton, fish,and birds). Our approach provides a systematicstandardized way to integrate multiple metrics fromdifferent taxonomic groups by addressing four elementscrucial to analyzing data from multiple indicators: covariate control, re-scaling of data, standardizing the sign of responses, and dimensional reduction. We evaluated the biologicalmetrics against individual environmental stressors andagainst multivariate physicochemical metricscharacterizing general anthropogenic stress among thelakes. The method detected a response to variationin the gross environmental condition of the lakes thatwas correlated across taxa and metrics. In addition,a differential response to near shore conditions wasdemonstrated for fish. The success of the approach inthis study lends support to its general application toecological monitoring involving complex data sets.     

Concentrations of Cadmium, Mercury and Selenium in Blood, Liver and Kidney of Common Eider Ducks from the Canadian Arctic

We determined concentrations of selected trace elements inlivers, kidneys and blood samples from common eiders (Somateria mollissima borealis) from the eastern Canadianarctic during 1997 and 1998. Concentrations of totalmercury and organic mercury were generally low in the liversof these birds (less than 6 and 4 g g^–1 dry wt,respectively). Selenium ranged between 11–47 g g^–1 inlivers. Renal cadmium concentrations were among the highestever published for this species (range: 47–281 g g^–1). The regressions of log-transformed concentrations ofthese trace elements in blood samples on those in liver orkidney were significant (all P-values < 0.05) andpositive. However, except for organic mercury (RM ² = 0.83), the co-efficients of determination were low tomoderate (range of R ²: 0.26–0.52), suggesting poorto moderate predictive capability. Furthermore, therelationships between total mercury in blood and liverchanged between 1997 and 1998, suggesting that it would notbe possible to predict consistently, concentrations ofmercury in blood from those in liver based on samples takenin one year. Blood samples can be used to determineconcentrations of these trace elements in common eiders (andprobably other sea duck species as well). The use of bloodsamples is especially warranted when it is undesirable tokill the animal such as when working with rare or endangeredsea duck species or when the objective is to relate traceelement exposure to annual survival rates. However, thepredictive equations developed here should not be used topredict expected concentrations in one type of tissue fromthose in the other.