H_4SiW_(12)O_(40)/TiO_2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析.研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响.实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%.     

光纤传导可见光降解亚甲基蓝

针对浓度大、色度高的印染废水难以处理的情况,选用加入光纤的光催化体系进行研究。采用溶胶凝胶法制备了Ag+/TiO2粉体光催化剂,用固体紫外可见光谱、X射线衍射对其进行表征。选用亚甲基蓝溶液作为目标降解物,评价了Ag+/TiO2在可见光下的光催化活性。分别考察了加入石英芯侧光光纤与塑料侧光光纤反应体系下,催化剂量、光纤数量、光照强度和pH值等因素对亚甲基蓝降解实验的影响。结果表明,选用20 mg/L的亚甲基蓝,采用催化剂量为11.67 g/L,500根侧光光纤,300 W的外部光源,pH值约为11时,光催化降解效果最佳,均能达到90%以上。     

磷钨酸光催化降解甲基橙溶液的研究

以磷钨酸为光催化刺，在紫外灯照射下。对模拟染料废水甲基橙溶液进行光催化降解，并研究了催化剂加入量、pH值、甲基橙初始浓度和外加氧化剂H2O2对光催化降解效果的影响。结果表明，磷钨酸光催化剂加入量为300mg／100mL，pH=2．5时，甲基橙溶液的降解率明显高于其他pH值的降解率；在较低浓度下，甲基橙溶液的光催化降解反应符合一级动力学方程；外加氧化剂H2O2可提高光催化反应速率。     

TiO2光催化-微滤膜分离深度净化亚甲基蓝印染废水

采用悬浮式TiO2光催化膜反应器深度净化纺织工业园区含亚甲基蓝印染废水经生物处理二级出水,利用中空纤维微滤膜进行催化剂截留分离,研究催化剂投加量、运行时间、溶解氧、搅拌方式对出水水质及膜通量的影响。结果表明:光催化会消耗体系溶解氧,鼓风曝气搅拌可同时为系统供氧,优于机械搅拌;该耦合体系的催化剂最佳投加量为1 g/L,经光催化氧化-膜组合工艺处理后水质优于GB 4287-1992《纺织染整工业污染物排放标准》的I级标准,符合建设部颁布的《生活杂用水水质标准》(CJ/T 48-1999)。     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

纳米Au/TiO2复合物光催化降解亚甲基蓝

以纳米金棒为掺杂物,采用溶胶-凝胶法制备了纳米Au/TiO2复合材料,在紫外光下对亚甲基蓝溶液进行光催化降解。结果表明,在紫外光下,Au/TiO2复合物对亚甲基蓝的脱色率最高可达99.6%,是纯TiO2的1.3倍。这主要归结于掺杂纳米尺寸的Au可增加TiO2对光的吸收以及减少电子-空穴对的复合,由此提高其光催化能力。     

磷钨酸光催化降解甲基橙溶液的研究

以磷钨酸为光催化剂,在紫外灯照射下,对模拟染料废水甲基橙溶液进行光催化降解,并研究了催化剂加入量、pH值、甲基橙初始浓度和外加氧化剂H2O2对光催化降解效果的影响.结果表明,磷钨酸光催化剂加入量为300 mg/100 mL,pH=2.5时,甲基橙溶液的降解率明显高于其他pH值的降解率;在较低浓度下,甲基橙溶液的光催化降解反应符合一级动力学方程;外加氧化剂H2O2可提高光催化反应速率.     

亚甲基蓝表面修饰纳米TiO2降解造纸废水动力学

以亚甲基蓝(MB)作为表面修饰剂,采用简单的化学吸附法制备亚甲基蓝表面修饰的纳米TiO2光催化剂(TiO2-MB)。经表面修饰后,TiO2-MB光催化剂波长响应范围红移至可见光区575 nm处。探讨了光催化剂量、光照时间和溶液pH值对TiO2-MB光催化降解造纸废水的影响;研究了纳米TiO2-MB对造纸废水的暗吸附规律和光降解性能。结果表明:纳米TiO2-MB对造纸废水的吸附规律都较好地符合Langmuir和Freundlich吸附等温模型,属于吸热反应;光催化降解动力学符合Langmuir-Hinshelwood动力学模型。在160 W高压汞灯光照80 min,3.0 g/L纳米TiO2-MB光催化降解pH=2.0的造纸废水(COD:2 069.8 mg/L),COD去除率可达94.7%,处理效果远高于避光条件下。光催化剂经8次使用仍具有较高的催化活性。     

双室介质阻挡放电等离子体反应器降解亚甲基蓝

介质阻挡放电（DBD）等离子体技术可以有效地降解和矿化水中的亚甲基蓝（MB）分子。本文采用一种新型的双室DBD反应器通过处理亚甲基蓝溶液,研究了液体体积、下气室高度、输入功率、初始pH、初始浓度、曝气种类对MB降解的影响。结果表明,在液体体积50 mL、下气室高度7 mm、输入功率18 W、初始pH 4.0、初始浓度100 mg·L-1、氧气曝气时,MB可以在20 min内几乎脱色完全。并提出了MB的降解是脱甲基化、臭氧直接氧化和羟基化共同作用的结果。     

Azo-dyes photocatalytic degradation in aqueous suspension of TiO2 under solar irradiation

The photodegradation of two common and very stable azo-dyes, i.e. methyl-orange (C₁₄H₁₄N₃SO₃Na) and orange II (C₁₆H₁₁N₂SO₄Na), is reported. The photocatalytic oxidation was carried out in aqueous suspensions of polycrystalline TiO₂ irradiated by sunlight. Compound parabolic collectors, installed at the “Plataforma Solar de Almería” (PSA, Spain) were used as the photoreactors and two identical reacting systems allowed to perform photoreactivity runs for the two dyes at the same time and under the same irradiation conditions. The disappearance of colour and substrates together with the abatement of total organic carbon content was monitored. The main sulfonate-containing intermediates were found to be in lower number in respect to those obtained under artificial irradiation. In particular there were no more evidence of the presence of hydroxylated transients. The dependence of dye photooxidation rate on: (i) substrate concentration; (ii) catalyst amount; and (iii) initial pH was investigated. The influence of the presence of strong oxidant species (H₂O₂, S₂O₈²⁻) and some ions (Cl⁻, SO₄²⁻) on the process was also studied.     

一种光催化体系光催化降解苯胺的研究

以钛酸丁酯为原料．以膨润土为载体,用酸性溶胶法合成TiO2纳米复合物,并利用该复合物作催化剂,在H2O2存在下进行光催化降解苯胺溶液。结果表明,该催化剂在UV／H2O2系统中对苯胺溶液有很好的光催化降解效果,其效果优于纯TiO2;H2O2的存在提高了苯胺光催化降解速率,在本实验条件下其最佳摩尔浓度是5mmol／L;溶液pH是影响反应速率的重要因素．pH在中性范围内具有更强的光催化活性;该体系中苯胺能够有效地被降解,其光催化反应遵循一级反应动力学规律。     

改性TiO_2光催化降解三苯甲烷类污染物

以硫酸钛为原料采用水热法制备了掺Fe3＋TiO2晶体粉末,采用X射线衍射仪（XRD）对样品的结构进行了表征。在可见光条件下,用溴酚蓝、甲基绿、甲基蓝、孔雀石绿、甲基紫和碱性品红等6种典型三苯甲烷类化合物为目标降解物,研究了以自制的掺Fe3＋TiO2晶体粉末对它们的催化降解作用。实验结果表明,制备的掺Fe3＋TiO2晶体属于锐钛矿型。6种化合物的光催化降解反应遵循拟一级动力学规律,且可用Langmuir-Hinshelwood（L-H）动力学模型描述,其表观反应速度常数（k）的大小顺序为：溴酚蓝〈甲基绿〈甲基蓝〈孔雀石绿〈甲基紫〈碱性品红,大小变化次序与其半衰期t1/2成反比,并从分子结构上对它们的降解规律进行定性解释。     

TiO_2微球光催化降解腐植酸钠

以阳离子交换树脂为模板,采用溶胶-凝胶法以四氯化钛为原料制备TiO2微球,采用XRD,FTIR,SEM对样品进行了表征。微球中主要组分是锐钛矿型TiO2,同时掺杂有少量Na＋,SO24-等离子,比TiO2粉末具有更好的光催化性能,具备重复使用的能力,使用寿命较长,可作为一种有实用价值的光催化剂。在300 W高压汞灯下采用二氧化钛微球催化降解腐植酸钠,分析了催化剂投加量和反应时间对降解率的影响。腐植酸钠的光催化降解实验结果表明：初始浓度为10 mg/L的腐植酸钠在碱性条件,催化剂投加量为2.5 g/L,反应时间为3 h时最为适宜,最大降解率可达到96.51%。     

Azo-dyes photocatalytic degradation in aqueous suspension of TiO2 under solar irradiation

The photodegradation of two common and very stable azo-dyes, i.e. methyl-orange (C₁₄H₁₄N₃SO₃Na) and orange II (C₁₆H₁₁N₂SO₄Na), is reported. The photocatalytic oxidation was carried out in aqueous suspensions of polycrystalline TiO₂ irradiated by sunlight. Compound parabolic collectors, installed at the “Plataforma Solar de Almería” (PSA, Spain) were used as the photoreactors and two identical reacting systems allowed to perform photoreactivity runs for the two dyes at the same time and under the same irradiation conditions. The disappearance of colour and substrates together with the abatement of total organic carbon content was monitored. The main sulfonate-containing intermediates were found to be in lower number in respect to those obtained under artificial irradiation. In particular there were no more evidence of the presence of hydroxylated transients. The dependence of dye photooxidation rate on: (i) substrate concentration; (ii) catalyst amount; and (iii) initial pH was investigated. The influence of the presence of strong oxidant species (H₂O₂, S₂O₈²⁻) and some ions (Cl⁻, SO₄²⁻) on the process was also studied.     

纳米TiO2光催化降解酸性粒子元青溶液的研究

对纳米 Ti O2 光催化氧化法降解酸性粒子元青溶液进行了试验研究。结果表明 ,反应符合一级反应 ,反应速率常数为2 .9× 10 - 3min- 1。确立的最佳工艺条件 :催化剂的用量为 4.0 g·L- 1 ,溶液的 p H为 6.3 8,空气的体积流量为 12 0 m L· min- 1 ,在此最佳工艺条件下 ,酸性粒子元青的降解率达到 92 .3 %。且测得反应的表现活化能 Ea为 -17.9k J· mol- 1 。     

Photocatalytic degradation of phenol by visible light-responsive iron-doped TiO2 and spontaneous sedimentation of the TiO2 particles

Fe-doped TiO₂ was prepared by the calcination of Fe_xTiS₂ (x = 0, 0.002, 0.005, 0.008, 0.01) and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–visible diffuse reflectance spectra. All the Fe-doped TiO₂ were composed of an anatase crystal form and showed red shifts to a longer wavelength. The activity of the Fe-doped TiO₂ for the degradation of phenol was investigated by varying the iron content during UV (365 nm) and visible light (405 nm and 436 nm) irradiation. The degradation rate depended on the Fe content and the Fe-doped TiO₂ was responsive to the visible light as well as the elevated activity toward UV light. The molar ratio of 0.005 was the optimum for both the UV and visible light irradiations. The result was discussed on the basis of the balance of the excited electron–hole trap by the doped Fe³⁺ and their charge recombination on the doped Fe³⁺ level. The Fe-doped TiO₂ (x = 0.005) was more active than P25 TiO₂ under solar light irradiation. The suspended Fe-doped TiO₂ spontaneously precipitated once the stirring of the reaction mixture was terminated.     

Ru-TiO2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru—TiO2光电极,以该电极为工作电极,石墨作对电极,饱和甘汞电极为参比电极,对亚甲基蓝溶液的光电催化降解进行了研究。结果表明：煅烧温度600oC,掺杂1％Ru的Ru-TiO2光电极催化活性最好;以紫外灯（125W）为光源,当外加偏压0．2V,pH为5时,Ru-TiO2光电催化亚甲基蓝120min可使其完全脱色;亚甲基蓝的光电催化降解遵从Langmuir—Hinshelwood动力学模型,测得其反应速率常数k：0．781mmol／（L·min）,吸附常数K=0．225L／mmol。     

超声波-光催化氧化降解邻氯苯酚的研究

对超声波一光催化氧化降解邻氯苯酚(2-cp)进行了研究．探讨了溶液初始pH、TiO2投加量、H2O2投加量和溶液初始浓度对2-cp降解率的影响。并对几种不同处理方法降解2-cp的结果进行了对比。结果表明,超声波和紫外光的协同效果明显,在相同的反应时间内,超声波能够明显提高光催化降解2-cp的降解率。超声波和紫外光连用,具有良好的工业应用前景。