Ignition advancement study for optimized characteristics of a raw biogas operated spark ignition engine

In the current investigation, raw biogas obtained from rural sectors was used as the alternative to gasoline fuel in the spark ignition (SI) engine. The performance and efficiency are mainly dependent on the combustion phasing for which “ignition timing” is an effective tool in a SI engine. Hence, the objective of the present work is to understand the effect of “variable ignition timing” for a biogas-fueled SI engine. For this purpose, a single cylinder, 4-stroke, SI engine of rated power 4.5 kW was operated with raw biogas at a compression ratio (CR) of 10. By maintaining a speed of 1650 rpm, the engine was operated in wide open (WOT) and part throttle (PT) mode with an equivalence ratio of 0.81 and 0.83, respectively. It was observed that the biogas fueled SI engine was found to be operative only within the ignition advance (IA) range of 33–47° CA bTDC both in WOT and PT conditions. The results showed optimal brake power (BP), brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) are achieved at 45° CA bTDC. The average peak cylinder pressure, neat heat release rate (NHRR) and mean gas temperature (MGT) are also observed to be maximum while CO and HC emission at this point of IA were found to be minimum. Due to controlled and complete combustion, CO₂ and NO_x concentration in the exhaust emission were found to be higher at this point of ignition timing.     

Integrated energy management strategy of powertrain and cooling system for PHEV

ABSTRACT

Energy management strategy (EMS) is crucial in improving the fuel economy of plug-in hybrid electric vehicle (PHEV). Existing studies on EMS mostly manage powertrain and cooling system separately which cannot get the minimum total energy consumption. This paper aims to propose a novel EMS for a new type of dual-motor planetary-coupled PHEV, which considers cooling power demand and effect of temperature on fuel economy. Temperature-modified engine model, lithium-ion battery model, two motors, and cooling system models are established. Firstly, the separated EMS (S-EMS) is designed which manages powertrain and cooling system separately. Sequentially, after the analysis of thermal characteristics of the powertrain and cooling system, the thermal-based EMS (T-EMS) is then proposed to manage two systems coordinately. In T-EMS, cooling power demand and the charging/discharging energy of motors are calculated as equivalent fuel consumption and integrated into the object function. Besides, a fuzzy controller is also established to deicide the fuel-electricity equivalent factor with consideration of the effect of temperature and state of charge on powertrain efficiency. Finally, the hardware-in-loop experiment is carried out to validate the real-time effect of EMS under the New European Driving Cycle. The result shows that cooling power demand and temperature can significantly affect the fuel economy of the vehicle. T-EMS shows better performance in fuel economy than S-EMS. The equivalent fuel consumption of the cooling system of T-EMS decreases by 27% compared with that of S-EMS. The total equivalent fuel consumption over the entire trip of PHEV using T-EMS is reduced by 9.7%.     

Managing the cooling capacity of the upper rhine: A case study

In most industrialized countries, environmental standards exist which prescribe the maximum allowable man-made increase in water temperature of a river. Together with flowrate and weather conditions, these standards determine the rate at which waste heat may be discharged into a river at any moment. Power generating stations with variable cooling systems can adjust their heat discharge into the river in compliance with environmental standards and by doing so exert an influence on power generation capacity. In this paper, a scheme is developed that allows a chain of power stations discharging into the same river to operate their cooling systems such that the output of total electricity is maximized and water temperature standards are accomodated. The optimum balance between stations is determined through dynamic programming. From the results of a simulation model using historical data, simple decision rules for day-to-day operation are abstracted. These rules are based solely on the river flow rates at each power station.     

Combustion features under different center of heat release of a diesel engine using dimethyl carbonate/diesel blend

Experiments were performed in a single cylinder common-rail diesel engine that adopts a low temperature premixed charge compression ignition (PCCI) mode. Combustion features of dimethyl carbonate (DMC)-diesel blends under various centers of heat release (COHRs) were revealed in details. With retarding of COHR, all the peaks of pressure and pressure rise rate and bulk gas temperature are postponed and declined in sequence. Normally, the crank angle of peak pressure is quite close to the COHR, while the peak of bulk gas temperature appears about 7°CA after COHR as a rule. The prolongation can be demonstrated at every stage of combustion such as q₁₀ and q₉₀ with the COHR being put backward. In addition, the heat release of diesel is completely slower than that of D10 fuel at various stages. Unfortunately, retarding of COHR implies a declining thermal efficiency of engines as well as a higher cyclic variation in general. Nevertheless, D10 blend has higher thermal efficiency than diesel thanks to high oxygen content of DMC and low boiling point that prompts better fuel atomization and complete combustion. Meanwhile, the cyclical variation of D10 is greater than diesel fuel owing to the low heat value, high latent heat of vaporization, and poor flammability of DMC. As a total, a comprehensive understanding of PCCI combustion features under different COHRs can be conducive to conducting effective management of combustion process and manipulating the subsequent emission performance to a favorable level.     

THERMAL DISCHARGES AND PUBLIC POLICY DEVELOPMENT1

ABSTRACT The generation of electric energy in steam-electric power plants is accompanied by the discharge of large quantities of waste heat into the environment. In most cases, this heat is released into natural bodies of water at temperatures relatively close to ambient. In certain locations, such as the Chesapeake Bay, discharges of waste heat may triple in the next decade. It is expected that past practices of thermal discharge, if continued into the future, will result in significant damages to other legitimate users of the water resource, both present and future. This paper reviews the economic causes of these potential damages, and describes the role of public policy as one of removing such causes through regulation incentive or intervention. Possible public policies are reviewed, including prohibition, standards, various types of dollar incentives such as taxes and subsidies, marketable effluent permits, and direct government investment. The innovative power plant siting program recently adopted in Maryland is also discussed. It is concluded that no statements can be made regarding the comparative efficiency or effectiveness of the various policies at the present state of knowledge. It is recommended that policy-makers adopt mixed strategies, preserving as many options as possible for dealing with similar problems in the future.     

Oxy-fuel coal combustion—A review of the current state-of-the-art

Carbon dioxide emissions will continue being a major environmental concern due to the fact that coal will remain a major fossil-fuel energy resource for the next few decades. To meet future targets for the reduction of greenhouse gas (GHG) emissions, capture and storage of CO₂ is required. Carbon capture and storage technologies that are currently the focus of research centres and industry include: pre-combustion capture, post-combustion capture, and oxy-fuel combustion. This review deals with the oxy-fuel coal combustion process, primarily focusing on pulverised coal (PC) combustion, and its related research and development topics. In addition, research results related to oxy-fuel combustion in a circulating fluidised bed (CFB) will be briefly dealt with.During oxy-fuel combustion, a combination of oxygen, with a purity of more than 95 vol.%, and recycled flue gas (RFG) referred to as oxidant is used for combusting the fuel producing a gas consisting of mainly CO₂ and water vapour, which after purification and compression, is ready for storage. The high oxygen demand is supplied by a cryogenic air separation process, which is the only commercially available mature technology. The separation of oxygen from air as well as the purification and liquefaction of the CO₂-enriched flue gas consumes significant auxiliary power. Therefore, the overall net efficiency is expected to be decreased by 8–12% points, corresponding to a 21–35% increase in fuel consumption. Alternatively, ion transport membranes (ITMs) are proposed for oxygen separation, which might be more energy efficient. However, since ITMs are far away from becoming a mature technology, it is widely expected that cryogenic air separation will be the selected technology in the near future. Oxygen combustion is associated with higher temperatures compared with conventional air combustion. Both fuel properties as well as limitations of steam and metal temperatures of the various heat exchanger sections of the boiler require a moderation of the temperatures in the combustion zone and in the heat-transfer sections. This moderation in temperature is accomplished by means of recycled flue gas. The interdependencies between the fuel properties, the amount and temperature of the recycled flue gas, and the resulting oxygen concentration in the combustion atmosphere are reviewed.The different gas atmosphere resulting from oxy-fuel combustion gives rise to various questions related to firing, in particular, with respect to the combustion mechanism, pollutant reduction, the risk of corrosion, and the properties of the fly ash or its resulting deposits. In this review, detailed nitrogen and sulphur chemistry was investigated in a laboratory-scale facility under oxy-fuel combustion conditions. Oxidant staging succeeded in reducing NO formation with effectiveness comparable to that typically observed in conventional air combustion. With regard to sulphur, a considerable increase in the SO₂ concentration was measured, as expected. However, the H₂S concentration in the combustion atmosphere in the near-flame zone increased as well. Further results were obtained in a pilot-scale test facility, whereby acid dew points were measured and deposition probes were exposed to the combustion environment. Slagging, fouling and corrosion issues have so far been addressed via short-term exposure and require further investigation.Modelling of PC combustion processes by computational fluid dynamics (CFD) has become state-of-the-art for conventional air combustion. Nevertheless, the application of these models for oxy-fuel combustion conditions needs adaptation since the combustion chemistry and radiative heat transfer is altered due to the different combustion gas atmosphere.CFB technology can be considered mature for conventional air combustion. In addition to its inherent advantages like good environmental performance and fuel flexibility, it offers the possibility of additional heat exchanger arrangements in the solid recirculation system, i.e. the ability to control combustion temperatures despite relatively low flue gas recycle ratios even when combusting in the presence of high oxygen concentrations.     

Radiant Domestic Combustion Stove System: Experimental and Simulated Study of Energy Use and Thermal Comfort

A steady-state space radiant heat model and a stove combustion model are developed to simulate the heat exchanges between various surfaces in the room and the stove and stack surfaces, assuming stiochiometric combustion inside the stove and the exhaust gases flow out through the stack by natural convection. The space heat model calculates the fuel consumption, the stove, stack temperatures, and the mass flow rate of exhaust gases, and provides an opportunity to study the energy efficiency of the stove, while satisfying the constraints of thermal comfort. Fanger (1982) Fanger, P. O. 1982. Thermal Comfort Analysis and Applications in Engineering, 156–198. New York: McGraw Hill.  [Google Scholar] model and a radiation exchange model between various surfaces of the space, the thermal building energy balance, and stove combustion process is applied to determine the mean radiant temperature (MRT) and the extent of thermal comfort as determined by predicted mean vote (PMV).

The overall model is validated by performing experiments in a room placed inside a controlled outdoor environment. The room is heated using a domestic stove common for rural areas of Lebanon and the MRT, the room air temperature, the walls and window temperatures are measured at two stove positions. The measured MRT, the average room temperature, and the wall surface temperatures agreed within ±7% of values predicted by the numerical model.

A parametric study is performed to optimize the stove and occupant locations in the room where adequate comfort level can be maintained at lower fuel consumption levels. The values of MRT and PMV depend strongly on the position of the radiant stove heater and stack with respect to the cold window and the occupant location. It is shown that it is possible to save up to 15% in stove fuel consumption by changing the stove position in the room with respect to the window and to the person, while maintaining the same level of comfort.     

Development of a PEMFC-based heat and power cogeneration system

Hydrogen-fed proton exchange membrane fuel cell (PEMFC) has to overcome high installation and operation cost before being adopted as a distributed power candidate. Cogeneration of power and heat is a good approach to increase hydrogen energy utilization rate. A PEMFC-based power and heat cogeneration system is proposed and established in the current study to investigate system’s technological and economical feasibility. This cogeneration of heat and power (CHP) system composes of a 2.5-kW fuel cell stack, hydrogen supply system, air supply system, water and heat management system, and heat recovery system. The control strategies to automate the system operation are realized by a programmable automation controller (PAC) system. Detailed measurement of the system is also constructed along with a web-based human–machine interface (HMI) platform to facilitate experiments and demonstration. Preliminary testing of the CHP system shows good performance of heat and power outputs. System’s electrical power conversion efficiency and thermal efficiency of the CHP system are measured at 38% and 35%, respectively. System combined efficiency therefore reached about 73%.     

利用循环流化床锅炉燃烧技术处理造纸亚铵黑液

循环流化床燃烧技术是一种低温(900℃)流化态燃烧技术,可以燃烧低发热值的生物质燃料.采用循环流化床低温燃烧和分段燃烧技术,通过锅炉尾部凝汽换热设备将黑液加热浓缩,这样既可满足循环流化床锅炉燃烧的条件,又使得脱硫效率提高,SO2的生成量降低,且使各项排放指标均能达到环保排放标准.对比国内外造纸黑液处理办法,我们得出了利用循环流化床锅炉燃烧技术处理亚铵黑液的可行性.对于我国现阶段的小型造纸厂,该技术具有一定的推广应用价值.     

CO2 capture from combined cycles integrated with Molten Carbonate Fuel Cells

In this paper Molten Carbonate Fuel Cells (MCFCs) are considered for their potential application in carbon dioxide separation when integrated into natural gas fired combined cycles. The MCFC performs on the anode side an electrochemical oxidation of natural gas by means of CO₃^2? ions which, as far as carbon capture is concerned, results in a twofold advantage: the cell removes CO₂ fed at the cathode to promote carbonate ion transport across the electrolyte and any dilution of the oxidized products is avoided.The MCFC can be “retrofitted” into a combined cycle, giving the opportunity to remove most of the CO₂ contained in the gas turbine exhaust gases before they enter the heat recovery steam generator (HRSG), and allowing to exploit the heat recovery steam cycle in an efficient “hybrid” fuel cell + steam turbine configuration. The carbon dioxide can be easily recovered from the cell anode exhaust after combustion with pure oxygen (supplied by an air separation unit) of the residual fuel, cooling of the combustion products in the HRSG and water separation. The resulting power cycle has the potential to keep the overall cycle electrical efficiency approximately unchanged with respect to the original combined cycle, while separating 80% of the CO₂ otherwise vented and limiting the size of the fuel cell, which contributes to about 17% of the total power output so that most of the power capacity relies on conventional low cost turbo-machinery. The calculated specific energy for CO₂ avoided is about 4 times lower than average values for conventional post-combustion capture technology. A sensitivity analysis shows that positive results hold also changing significantly a number of MCFC and plant design parameters.     

Analysis of an intermediate-temperature proton-conducting SOFC hybrid system

The performance of an intermediate-temperature proton-conducting solid oxide fuel cell (pSOFC) hybrid system is investigated in this work. The hybrid system consists of a 20-kW pSOFC, a micro gas turbine (MGT), and heat exchangers. Heat exchangers are used to recover waste heat from pSOFC and MGT. The performance of the system is analyzed by using Matlab/Simulink/Thermolib. Flow rates of air and hydrogen are controlled by assigning different stoichiometric ratio (St). St considered in this study is between 2 and 3.5 for air, and between 1.25 and 1.45 for hydrogen. Results show that the combined heat and power (CHP) efficiency increases as the fuel St decreases or air St increases. This is because lowering fuel St means fewer fuel will be wasted from the fuel cell stack, so the CHP efficiency increases. On the other hand, as air St increases, the amount of recovered waste heat increases, so does the CHP efficiency.     

CO2 emissions reduction from the power system in India

The power system in India accounts for nearly one-third of CO₂ emissions of the country as a whole. A comparison of some of the technical options to reduce CO₂ emissions is presented in this paper. A linear programming framework is used to simulate the integrated optimal operation of the three regional grids, and it is shown that such operations lead to lower fuel costs and to lower CO₂ emissions. The same framework is used to see how a rise in thermal efficiency translates into a CO₂ emissions reduction. Reduced fuel requirements also lead to reductions in other pollutants ie SO₂, NO_x and fly ash. The reductions in CO₂ emissions and other pollutants are at far lower cost in the case of integrated optimal operations as compared to reductions due to gas fuelled generation or thermal efficiency improvements. However, thermal efficiency improvements under optimal integrated operations result in much higher reductions in operating costs, coal consumption and total emissions of all pollutants.     

The role of electricity in sustainable development

Current projections estimating world population growth read in conjunction with corresponding projections of increased world energy consumption, point to electricity as the cleaner fuel of the future, especially because of its high efficiency and low levels of pollution. Due mostly to the fact that the electrical end-use devices are considerably more efficient than those using other forms of energy, most developed countries show decreasing curves of energy intensity as technologies become more sophisticated and shift over to increased reliance on electricity. It is therefore argued in this article that a gradual shift away from fossil fuels to electricity is a promising possibility to bring down global air pollution and emissions of greenhouse gases to acceptable levels. Examples are given of greater efficiency achieved by electrification. Overall gains in energy efficiency from the change over from fossil fuels to electricity, are possible even in situations where the electricity is generated by fossil fuel combustion, despite the loss of primary energy in the conversion process. The article also presents electricity generating projects designed for developing countries and countries with economies in transition. The generation of electricity from the combustion of renewable sources (biomass waste), fossil fuels, and other innovative methods are outlined.     

注汽锅炉烟气余热利用技术应用

通过对注汽锅炉烟气余热利用潜力分析和开展余热利用方式对比分析,采用了在对流段安装热管换热器,通过换热器将烟气余热与助燃空气换热,余热利用技术的现场应用,实现了注汽锅炉燃料单耗降低的目的,取得良好的节能效果。     

Electric power and the environment: an analysis of pollutant emissions at Argentine state-owned electric power stations

This paper describes the impact on particulate and 'greenhouse gases' emissions of substitution policies implemented by Argentine state-owned electric power stations. Those policies involve the substitution, on the one hand, of hydroelectric and nuclear energy for conventional thermal energy and, on the other hand, of natural gas for fuel oil, diesel oil and coal. As additional investments are required in conventional thermal power stations to prevent environmental pollution, the investment savings generated by substitution policies have been calculated. While the environmental impact of hydroelectric, nuclear and natural gas facilities is locally significant and is experienced in geographical areas away from cities, there can be no doubt that the substitution policies implemented in the Argentine electricity sector have overall both ecological and economic benefits.     

A Novel Solar Thermal Cycle with Chemical Looping Combustion

In this paper, we have proposed a thermal cycle with the integration of chemical-looping combustion and solar thermal energy with the temperature of about 500-600°C. Chemical-looping combustion may be carried out in two successive reactions between a reduction of hydrocarbon fuel with metal oxides and a reduced metal with oxygen in the air. This loop of chemical reactions is substituted for conventional combustion of fuel. Methane as a fuel and nickel oxides as an oxygen carrier were employed in this cycle. Collected high-temperature solar thermal energy is provided for the endothermic reduction reaction. The feature of the proposed cycle is investigated through Energy-Utilization Diagram methodology. As a result, at the turbine inlet temperature of 1200°C, the exergy efficiency of the proposed cycle would be expected to be about 4 percentage points higher than that of a conventional gas turbine combined cycle. Compared to the previous study of chemical-looping combustion energy systems, the proposed cycle with the integration of green energy and traditional hydrocarbon fuels will offer the possibility of both greenhouse gas mitigation, with green energy, and a new approach to the efficient use of solar energy.     

An experimental apparatus for testing biodiesels based on a CFR engine—setup and validation with different methyl ester blends

A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NO_X emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.     

Investigation the effect of adding graphene oxide into diesel/higher alcohols blends on a diesel engine performance

ABSTRACT

This article aims to study the influence of the addition of graphene oxide nanoparticles (GO) to diesel/higher alcohols blends on the combustion, emission, and exergy parameters of a CI engine under various engine loads. The higher alcohols mainly n-butanol, n-heptanol, and n-octanol are blended with diesel at a volume fraction of 50%. Then, the 25 and 50 mg/L concentrations of GO are dispersed into diesel/higher alcohols blends using an ultrasonicator. The GO structures are examined using TEM, TGA, XRD and FTIR. The findings show that there is a reduction in p_max. and HRR when adding higher alcohols with diesel fuel. Regarding engine emission, there is a significant improvement in emissions formation with adding higher alcohols. The addition of GO into diesel/higher alcohols blends improves the brake thermal efficiency by 15%. Moreover, the p_max. and HRR are both enhanced by 4%. The CO, UHC and smoke formation are reduced considerably by 40%, 50 and 20%, respectively, while NO_x level is increased by 30% with adding GO. Finally, adding high percentages of n-butanol, n-heptanol, and n-octanol with diesel fuel with the presence of GO has the potential to achieve ultra-low CO, UHC, and smoke formation meanwhile keeping high thermal efficiency level.     

层燃螺旋炉排焚烧技术处理含油污泥研究

通过对几种含油污泥无害化处理技术的比选,分析不同处理技术物耗、能耗情况,优选出经济有效的含油污泥焚烧技术,结合新疆油田含油污泥的特点,采用层燃螺旋炉排焚烧技术,利用其燃烧热能生产蒸汽用于原油生产,采用余热吸收急冷与碱液半干法除酸技术,有效控制了二次污染;采用布袋除尘与烟尘固化技术确保了烟气达标排放。年节省成本支出3095.88万元。     

Verdant vehicles via viscoelasticity

The combustion of hydrocarbon (HC) fuels in internal combustion (IC) engines is modified by the presence of a few parts per million of megadalton molecular weight elastomers. The viscoelasticity imparted provides: reduced fuel vaporization, lesser back pressure, larger average droplet sizes, and lower combustion chamber temperatures. These effects result in: a reduction of emissions of HC, CO and NO_x of more than 70%, a substantial decrease in the number of particulates from diesel engines, a drop in combustion temperatures of more than 30vv°C, increases in engine power of more than 10%, an improved fuel octane rating, and economies of fuel consumption of more than 20%. The results are magnified during transitions, especially in the lower gears, used more often in urban traffic, where normal fuels emit more pollutants. These effects have a positive public health impact due to reductions in ozone, acid rain, particulates and partially oxidized HC.