Correlation between PM concentrations and aerosol optical depth in eastern China

Using one year of Aerosol Optical Depth (AOD) derived from Moderate Resolution Imaging Spectroradiometer (MODIS) on the Terra satellite and particular matter (PM) contents measured at eleven sites located mostly in the eastern China in 2007, the relationship between columnar AOD and hourly and daily average (DA) PM were established. The peak AOD observed from MODIS was generally consistent with the surface PM measurements in eastern China, where Zhengzhou had the maximum annual mean PM₁₀ of 182.1 μg m^?3, while Longfengshan had the minimum annual mean of 38.1 μg m^?3. Ground level observations indicated that PM concentration varies widely across different regions, which was mainly due to the difference in weather conditions and anthropogenic emissions. The coarse particles accounted for the main air pollution in Zhengzhou and Benxi whiles the fine particles, however, were the main constituents in other sites. Results showed that MODIS AOD (averaged over the box of 5 × 5 and 3 × 3 pixels) had a better positive correlation with the coincident hourly average (HA) PM concentration than with DA due to diurnal variation in PM mass measurements. After correcting AOD for relative humidity (RH), the correlation did not improve significantly, suggesting that the RH was not the main factor affecting the correlation of PM with AOD. The statistical regression analysis between MODIS AOD and PM mass suggested that the satellite-derived AOD is a useful tool for mapping PM distribution over large spatial domains.     

Spatiotemporal distribution and short-term trends of particulate matter concentration over China, 2006–2010

Air quality problems caused by atmospheric particulate have drawn broad public concern in the global scope. In the paper, the spatiotemporal distributions of fine particle (PM2.5) and inhalable particle (PM10) concentrations estimated with the artificial neural network (ANN) over China during 2006 to 2010 have been discussed. Most high PM10 concentration appears in Xinjiang, Qinghai, Gansu, Ningxia, Hubei, and parts of Inner Mongolia. The distribution of PM2.5 concentration is consistent with China’s three gradient terrains. The seasonal variations of PM2.5 and PM10 concentrations both indicate that they are higher in north China in spring and winter, lowest in summer. In autumn, most provinces in south China appear high value. In particular, high PM2.5 concentration appears in the southeast coastal cities while high PM10 concentration prefers the central regions in south China. On this basis, seasonal Mann–Kendall test method is utilized to analyze the short-term trends. The results also show significant changes of PM2.5 and PM10 concentrations of China in the past 5 years, and most provinces present the tendency of reduction (3–5 μg/m³ for PM2.5 and 10–20 μg/m³ for PM10 per year) while a fraction of provinces appear the increasing trend of 8–16 μg/m³ (PM2.5) and 16–30 μg/m³ (PM10). Simultaneously, PM2.5 population exposure is discussed with the combination of population density-gridded data. Municipalities get much higher exposure level than other provinces. Shanghai suffers the highest population exposure to PM2.5, followed by Beijing and then Tianjin, Jiangsu province. Most provincial capitals, such as Guangzhou, Nanjing, Chengdu, and Wuhan, face much higher exposure level than other regions of their province. Moreover, the PM2.5 exposure situation is more serious in southeast than northwest regions for Beijing-Tianjin-Hebei region. Also, per capita PM2.5 concentration and population-weighted PM2.5 concentration are calculated. The former shows that the high-level regions distribute in Guangdong, Shanghai, and Tianjin, while the latter in Hebei, Chongqing, and Shandong provinces. Further studies may consider optimizing concentration estimation model and use it to discuss the effects of particulate matters on human health.     

Estimating fine particulate matter component concentrations and size distributions using satellite-retrieved fractional aerosol optical depth: part 2--a case study

We use the fractional aerosol optical depth (AOD) values derived from Multiangle Imaging Spectroradiometer (MISR) aerosol component measurements, along with aerosol transport model constraints, to estimate ground-level concentrations of fine particulate matter (PM2.5) mass and its major constituents in the continental United States. Regression models using fractional AODs predict PM2.5 mass and sulfate (SO4) concentrations in both the eastern and western United States, and nitrate (NO3) concentrations in the western United States reasonably well, compared with the available ground-level U.S. Environment Protection Agency (EPA) measurements. These models show substantially improved predictive power when compared with similar models using total-column AOD as a single predictor, especially in the western United States. The relative contributions of the MISR aerosol components in these regression models are used to estimate size distributions of EPA PM2.5 species. This method captures the overall shapes of the size distributions of PM2.5 mass and SO4 particles in the east and west, and NO3 particles in the west. However, the estimated PM2.5 and SO4 mode diameters are smaller than those previously reported by monitoring studies conducted at ground level. This is likely due to the satellite sampling bias caused by the inability to retrieve aerosols through cloud cover, and the impact of particle hygroscopicity on measured particle size distributions at ground level.     

On the successful use of a simplified model to simulate the succession of toxic cyanobacteria in a hypereutrophic reservoir with a highly fluctuating water level

Many freshwater bodies worldwide that suffer from harmful algal blooms would benefit for their management from a simple ecological model that requires few field data, e.g. for early warning systems. Beyond a certain degree, adding processes to ecological models can reduce model predictive capabilities. In this work, we assess whether a simple ecological model without nutrients is able to describe the succession of cyanobacterial blooms of different species in a hypereutrophic reservoir and help understand the factors that determine these blooms. In our study site, Karaoun Reservoir, Lebanon, cyanobacteria Aphanizomenon ovalisporum and Microcystis aeruginosa alternatively bloom. A simple configuration of the model DYRESM-CAEDYM was used; both cyanobacteria were simulated, with constant vertical migration velocity for A. ovalisporum, with vertical migration velocity dependent on light for M. aeruginosa and with growth limited by light and temperature and not by nutrients for both species. The model was calibrated on two successive years with contrasted bloom patterns and high variations in water level. It was able to reproduce the measurements; it showed a good performance for the water level (root-mean-square error (RMSE) lower than 1 m, annual variation of 25 m), water temperature profiles (RMSE of 0.22–1.41 °C, range 13–28 °C) and cyanobacteria biomass (RMSE of 1–57 μg Chl a L^?1, range 0–206 μg Chl a L^?1). The model also helped understand the succession of blooms in both years. The model results suggest that the higher growth rate of M. aeruginosa during favourable temperature and light conditions allowed it to outgrow A. ovalisporum. Our results show that simple model configurations can be sufficient not only for theoretical works when few major processes can be identified but also for operational applications. This approach could be transposed on other hypereutrophic lakes and reservoirs to describe the competition between dominant phytoplankton species, contribute to early warning systems or be used for management scenarios.     

Short-term effects of atmospheric particulate matter on myocardial infarction: a cumulative meta-analysis

Atmospheric particulate matter (PM) is hypothesized to increase the risk of myocardial infarction (MI). However, the epidemiological evidence is inconsistent. We identified 33 studies with more than 4 million MI patients and applied meta-analysis and meta-regression to assess the available evidence. Twenty-five studies presented the effects of the PM level on hospitalization for MI patients, while eight studies showed the effects on mortality. An increase in PM₁₀ was associated with hospitalization and mortality in myocardial infarction patients (RR per 10 μg/m³?=?1.011, 95 % CI 1.006–1.016; RR per 10 μg/m³?=?1.008, 95 % CI 1.004–1.012, respectively); PM_2.5 also increased the risk of hospitalization and mortality in MI patients (RR per 10 μg/m³?=?1.024, 95 % CI 1.007–1.041 for hospitalization and RR per 10 μg/m³?=?1.012, 95 % CI 1.010–1.015 for mortality). The results of the cumulative meta-analysis indicated that PM₁₀ and PM_2.5 were associated with myocardial infarctionwith the addition of new studies each year. In conclusion, short-term exposure to high PM₁₀ and PM_2.5 levels revealed to increase risk of hospitalization and mortality for myocardial infarction. Policy support of pollution control and individual protection was strongly recommended.     

Removal ratio of gaseous toluene and xylene transported from air to root zone via the stem by indoor plants

This work was designed to investigate the removal efficiency as well as the ratios of toluene and xylene transported from air to root zone via the stem and by direct diffusion from the air into the medium. Indoor plants (Schefflera actinophylla and Ficus benghalensis) were placed in a sealed test chamber. Shoot or root zone were sealed with a Teflon bag, and gaseous toluene and xylene were exposed. Removal efficiency of toluene and total xylene (m, p, o) was 13.3 and 7.0 μg·m^?3·m^?2 leaf area over a 24-h period in S. actinophylla, and was 13.0 and 7.3 μg·m^?3·m^?2 leaf area in F. benghalensis. Gaseous toluene and xylene in a chamber were absorbed through leaf and transported via the stem, and finally reached to root zone, and also transported by direct diffusion from the air into the medium. Toluene and xylene transported via the stem was decreased with time after exposure. Xylene transported via the stem was higher than that by direct diffusion from the air into the medium over a 24-h period. The ratios of toluene transported via the stem versus direct diffusion from the air into the medium were 46.3 and 53.7 % in S. actinophylla, and 46.9 and 53.1 % in F. benghalensis, for an average of 47 and 53 % for both species. The ratios of m,p-xylene transported over 3 to 9 h via the stem versus direct diffusion from the air into the medium was 58.5 and 41.5 % in S. actinophylla, and 60.7 and 39.3 % in F. benghalensis, for an average of 60 and 40 % for both species, whereas the ratios of o-xylene transported via the stem versus direct diffusion from the air into the medium were 61 and 39 %. Both S. actinophylla and F. benghalensis removed toluene and xylene from the air. The ratios of toluene and xylene transported from air to root zone via the stem were 47 and 60 %, respectively. This result suggests that root zone is a significant contributor to gaseous toluene and xylene removal, and transported via the stem plays an important role in this process.     

Nitrogen and plant population change radiation capture and utilization capacity of sunflower in semi-arid environment

The combination of nitrogen and plant population expresses the spatial distribution of crop plants. The spatial distribution influences canopy structure and development, radiation capture, accumulated intercepted radiation (Sa), radiation use efficiency (RUE), and subsequently dry matter production. We hypothesized that the sunflower crop at higher plant populations and nitrogen (N) rates would achieve early canopy cover, capture more radiant energy, utilize radiation energy more efficiently, and ultimately increase economic yield. To investigate the above hypothesis, we examined the influences of leaf area index (LAI) at different plant populations (83,333, 66,666, and 55,555 plants ha^?1) and N rates (90, 120, and 150 kg ha^?1) on radiation interception (Fi), photosynthetically active radiation (PAR) accumulation (Sa), total dry matter (TDM), achene yield (AY), and RUE of sunflower. The experimental work was conducted during 2012 and 2013 on sandy loam soil in Punjab, Pakistan. The sunflower crop captured more than 96% of incident radiant energy (mean of all treatments), 98% with a higher plant population (83,333 plants ha^?1), and 97% with higher N application (150 kg ha^?1) at the fifth harvest (60 days after sowing) during both study years. The plant population of 83,333 plants ha^?1 with 150 kg N ha^?1 ominously promoted crop, RUE, and finally productivity of sunflower (AY and TDM). Sunflower canopy (LAI) showed a very close and strong association with Fi (R ² = 0.99 in both years), PAR (R ² = 0.74 and 0.79 in 2012 and 2013, respectively), TDM (R ² = 0.97 in 2012 and 0.91 in 2013), AY (R ² = 0.95 in both years), RUE for TDM (RUE_TDM) (R ² = 0.63 and 0.71 in 2012 and 2013, respectively), and RUE for AY (RUE_AY) (R ² = 0.88 and 0.87 in 2012 and 2013, respectively). Similarly, AY (R ² = 0.73 in 2012 and 0.79 in 2013) and TDM (R ² = 0.75 in 2012 and 0.84 in 2013) indicated significant dependence on PAR accumulation of sunflower. High temperature during the flowering stage in 2013 shortened the crop maturity duration, which reduced the LAI, leaf area duration (LAD), crop growth rate (CGR), TDM, AY, Fi, Sa, and RUE of sunflower. Our results clearly revealed that RUE was enhanced as plant population and N application rates were increased and biomass assimilation in semi-arid environments varied with radiation capture capacity of sunflower.     

Monitoring an outdoor smoking area by means of PM<Subscript>2.5</Subscript> measurement and vegetal biomonitoring

The extension of pollutant accumulation in plant leaves associated with its genotoxicity is a common approach to predict the quality of outdoor environments. However, this approach has not been used to evaluate the environmental quality of outdoor smoking areas. This study aims to evaluate the effects of environmental tobacco smoke (ETS) by assessing particulate matter 2.5 μm (PM_2.5) levels, the pollen abortion assay, and trace elements accumulated in plant leaves in an outdoor smoking area of a hospital. For this, PM_2.5 was measured by active monitoring with a real time aerosol monitor for 10 days. Eugenia uniflora trees were used for pollen abortion and accumulated element assays. Accumulated elements were also assessed in Tradescantia pallida leaves. The median concentration of PM_2.5 in the smoking area in all days of monitoring was 66 versus 34 μg/m³ in the control area (P?<?0.001). In addition, the elements Al, Cd, Cu, Ni, Pb, Rb, Sb, Se, and V in Tradescantia pallida and Al, Ba, Cr, Cu, Fe, Mg, Pb, and Zn in Eugenia uniflora were in higher concentration in the smoking area when compared to control area. Smoking area also showed higher rate of aborted grains (26.1?±?10.7 %) compared with control (17.6?±?4.5 %) (P?=?0.003). Under the study conditions, vegetal biomonitoring proved to be an effective tool for assessing ETS exposure in outdoor areas. Therefore, vegetal biomonitoring of ETS could be a complement to conventional analyses and also proved to be a cheap and easy-handling tool to assess the risk of ETS exposure in outdoor areas.     

Cytotoxic response in human lung epithelial cells and ion characteristics of urban-air particles from Torino,a northern Italian city

Recently, much attention has been devoted to urban air pollution because epidemiological studies have reported health impacts related to particulate matter (PM). PM10 and PM2.5 were collected during different seasons in Torino, a northern Italian city, and were characterised by inorganic chemical species (secondary particulates and bio-available iron). The biological effects of aqueous and organic solvent PM extracts on human epithelial lung A549 were evaluated, and the effects on cell proliferation and lactate dehydrogenase (LDH) release were assayed. The average PM10 concentration during the sampling period was 47.9?±?18.0 μg/m³; the secondary particles accounted for 49 %?±?9 % of the PM10 total mass, and the bio-available iron concentration was 0.067?±?0.045 μg/m³. The PM2.5/PM10 ratio in Torino ranged from 0.47 to 0.90 and was higher in cold months than in warm months. The PM10 and PM2.5 extracts inhibited cell proliferation and induced LDH release in a dose-dependent manner with a seasonal trend. The PM10 extract had a stronger effect on LDH release, whereas the PM2.5 extract more strongly inhibited cell proliferation. No significant differences were observed in the effects induced by the two extracts, and no significant correlations were found between the biological effects and the PM components evaluated in this study, thus emphasising the importance of the entire mixture in inducing a cytotoxic response.     

Impact of the mixing boundary layer on the relationship between PM2.5 and aerosol optical thickness

The purpose of this paper is to study the relationship between columnar aerosol optical thickness and ground-level aerosol mass. A set of Sun photometer, elastic backscattering lidar and TEOM measurements were acquired during April 2007 in Lille, France. The PM2.5 in the mixed boundary layer is estimated using the lidar signal, aerosol optical thickness, or columnar integrated Sun photometer size distribution and compared to the ground-level station measurements. The lidar signal recorded in the lowest level (240 m) is well correlated to the PM2.5 (R² = 0.84). We also show that the correlation between AOT-derived and measured PM2.5 is significantly improved when considering the mixed boundary layer height derived from the lidar. The use of the Sun photometer aerosol fine fraction volume does not improve the correlation.     

Estimating fine particulate matter component concentrations and size distributions using satellite-retrieved fractional aerosol optical depth: part 1--method development

We develop a method that uses both the total column aerosol optical depth (AOD) and the fractional AOD values for different aerosol types, derived from Multiangle Imaging SpectroRadiometer (MISR) aerosol data, to estimate ground-level concentrations of fine particulate matter (PM2.5) mass and its major constituents in eastern and western United States. Compared with previous research on linking column AOD with ground-level PM2.5, this method treats various MISR aerosol components as individual predictor variables. Therefore, the contributions of different particle types to PM2.5 concentrations can be estimated. When AOD is greater than 0.15, MISR is able to distinguish dust from non-dust particles with an uncertainty level of approximately 4%, and light-absorbing from non-light-absorbing particles with an uncertainty level of approximately 20%. Further analysis shows that MISR Version 17 aerosol microphysical properties have good sensitivity and internal consistency among different mixture classes. The retrieval uncertainty of individual fractional AODs ranges between 5 and 11% in the eastern United States, and between 11 and 31% in the west for non-dust aerosol components. These results provide confidence that the fractional AOD models with their inherent flexibility can make more accurate predictions of the concentrations of PM2.5 and its constituents.     

Physicochemical and toxicological characteristics of urban aerosols during a recent Indonesian biomass burning episode

Air particulate matter (PM) samples were collected in Singapore from 21 to 29 October 2010. During this time period, a severe regional smoke haze episode lasted for a few days (21–23 October). Physicochemical and toxicological characteristics of both haze and non-haze aerosols were evaluated. The average mass concentration of PM_2.5 (PM with aerodynamic diameter of ≤2.5 μm) increased by a factor of 4 during the smoke haze period (107.2 μg/m³) as compared to that during the non-smoke haze period (27.0 μg/m³). The PM_2.5 samples were analyzed for 16 priority polycyclic aromatic hydrocarbons (PAHs) listed by the United States Environmental Protection Agency and 10 transition metals. Out of the seven PAHs known as potential or suspected carcinogens, five were found in significantly higher levels in smoke haze aerosols as compared to those in the background air. Metal concentrations were also found to be higher in haze aerosols. Additionally, the toxicological profile of the PM_2.5 samples was evaluated using a human epithelial lung cell line (A549). Cell viability and death counts were measured after a direct exposure of PM_2.5 samples to A459 cells for a period of 48 h. The percentage of metabolically active cells decreased significantly following a direct exposure to PM samples collected during the haze period. To provide further insights into the toxicological characteristics of the aerosol particles, glutathione levels, as an indirect measure of oxidative stress and caspase-3/7 levels as a measure of apoptotic death, were also evaluated.     

Size mass distribution of water-soluble ionic species and gas conversion to sulfate and nitrate in particulate matter in southern Taiwan

A Micro-Orifice Uniform Deposition Impactor (MOUDI) and a Nano-MOUDI were employed to determine the size-segregated mass distributions of ambient particulate matter (PM) and water-soluble ionic species for particulate constituents. In addition, gas precursors, including HCl, HONO, HNO₃, SO₂, and NH₃ gases, were analyzed by an annular denuder system. PM size mass distribution, mass concentration, and ionic species concentration were measured during the day and at night during episode and non-episode periods in winter and summer. Average total suspended particle (TSP) concentrations during episode days in winter were as high as 153?±?33 μg/m³, and PM mass concentrations in summer were as low as one-third of that in winter. Generally, PM concentration at night was higher than that in the daytime in southern Taiwan during the sampling periods. In winter during the episode periods, the size-segregated mass distribution of PM mass concentration was mostly in the 0.32–3.2-μm range, and the PM concentration increased significantly in the range of 0.32–3.2 μm at night. Ammonium, nitrate, and sulfate were the dominant water-soluble ionic species in PM, contributing 34–48 % of TSP mass. High concentrations of ammonia (12.9–49 μg/m³) and SO₂ (2.6–27 μg/m³) were observed in the gas precursors. The conversion ratio was high in the PM size range of 0.18–3.2 μm both during the day and at night in winter, and the conversion ratio of episode days was 20 % higher than that of non-episode days. The conversion factor was high for both nitrogen and sulfur species at nighttime, especially on episode days.     

Concentration and size distribution of particulate matter in a new aviary system for laying hens in China

ABSTRACT

Particulate matter (PM) from poultry production facilities may strongly affect the health of animals and workers in the houses, and PM emitted to the ambient air is an important pollution source to the surrounding areas. Aviary system is considered as a welfare friendly production system for laying hens. However, its air quality is typically worse as compared with conventional cage systems, because of the higher PM concentration of indoor air and other airborne contaminants. Furthermore, PM’s physical property, which has a direct impact on the penetration depth into the lungs of the birds and humans, is largely unknown for the aviary system. Therefore, a systematic method was utilized to investigate the characteristics of particles in the aviary house with large cage aviary unit system (LCAU) in Beijing, China. For the field measurements, three measuring locations were selected with two inside and one outside the house with LCAU to continuously monitor PM concentrations and collect the samples for particle size distribution (PSD) analysis. Results showed that PM_2.5, PM₁₀, and total suspended particulate (TSP) concentrations averaged at 0.037 ± 0.025 mg/m³, 0.42 ± 0.10 mg/m³, and 1.92 ± 1.91 mg/m³, respectively. Particle concentrations increased from October to December due to less ventilation as the weather got colder, and were generally affected by stocking density, ventilation rate, birds’ activities, and housing system. Meanwhile, indoor PM_2.5 concentration was easily impacted by the ambient air quality. Mass median diameter (MMD) and mass geometric standard deviation (MGSD) of the TSP during the measurement were 18.92 ± 7.08 μm and 3.11 ± 0.31, respectively. Count median diameter (CMD) and count geometric standard deviation (CGSD) were 1.94 ± 0.14 μm and 1.48 ± 0.08, respectively. Results indicated that the aviary system can attain a good indoor condition by suitable system design and environment control strategy.

Implications: Indoor PM_2.5 concentration of the layer house can be significantly affected by ambient air quality when the air quality index (AQI) was larger than 100. PM_2.5 and PM₁₀ concentrations of the layer house with a LCAU system were comparable to the cage system. TSP concentration was higher, and PM size was larger than most of the cage system. System design, larger space volume, and higher ventilation rate were the main influence factors. Good indoor environment of the aviary system can be achieved through the reasonable design of the production system and appropriate environment control strategy.     

Mercury transfer from soil to olive trees. A comparison of three different contaminated sites

Mercury contents in soil and olive tree leaves have been studied in 69 plots around three different source areas of this element in Spain: Almadén (Ciudad Real), Flix (Tarragona) and Jódar (Jaén). Almadén was the world’s largest cinnabar (HgS) mining district and was active until 2003, Flix is the oldest Spanish chlor-alkali plant (CAP) and has been active from 1898 to the present day and Jódar is a decommissioned CAP that was active for 14 years (1977–1991). Total mercury contents have been measured by high-frequency modulation atomic absorption spectrometry with Zeeman effect (ZAAS-HFM) in the soils and olive tree leaves from the three studied areas. The average soil contents range from 182 μg kg^?1 in Flix to 23,488 μg kg^?1 in Almadén, while the average leaf content ranges from 161 μg kg^?1 in Jódar to 1213 μg kg^?1 in Almadén. Despite the wide range of data, a relationship between soil–leaf contents has been identified: in Almadén and Jódar, multiplicative (bilogarithmic) models show significant correlations (R?=?0.769 and R?=?0.484, respectively). Significant correlations were not identified between soil and leaf contents in Flix. The continuous activity of the Flix CAP, which remains open today, can explain the different uptake patterns for mercury, which is mainly atmospheric in origin, in comparison to the other two sites, where activity ceased more than 10 years ago and only soil uptake patterns based on the Michaelis–Menten enzymatic model curve are observed.     

Phycoremediation potential of marine microalga <Emphasis Type="Italic">Tetraselmis indica</Emphasis> on secondary treated domestic sewage for nutrient removal and biodiesel production

Marine microalga Tetraselmis indica (T. indica) was cultivated in secondary treated domestic sewage (STDS) in batch mode. Optimization studies showed that after 14 days of cultivation period, highest biomass yield reached was 0.88 ± 0.04 g/L at the optimum temperature of 27 ± 1 °C and light intensity of 135 μmol m^?2 s^?1. T. indica removed about 60.93% phosphate, 78.46% nitrate, 72.94% chemical oxygen demand (COD), 73.17% biological oxygen demand (BOD), 98.90% total dissolved solids (TDS) and heavy metals (83.11% Cd, 55.67% Ca, 45.12% Cu, 13.67% Mn, 50.88% Pb, and 98.92% Al) from STDS. The level of electrical conductivity was reduced to 0.0974 ± 0.045 dS/m. The fatty acid methyl ester (FAME) profile showed the presence of palmitic acid (12.91%), oleic acid (35.94%), linoleic acid (14.89%) and eicosanoic acid (12.34%). This study indicates the potential of T. indica for removal of pollutants from STDS and also its capability of biodiesel production.     

Haze is a risk factor contributing to the rapid spread of respiratory syncytial virus in children

This study investigated whether respiratory syncytial virus (RSV) infection in children was associated with ambient temperature and air pollutants in Hangzhou, China. A distributed lag non-linear model (DLNM) was used to estimate the effects of daily meteorological data and air pollutants on the incidence of RSV infection among children. A total of 3650 childhood RSV infection cases were included in the study. The highest air pollutant concentrations were in January to May and October to December during the year. The yearly RSV-positive rate was 10.0 % among children with an average age of 4.3 months. The highest RSV-positive rate occurred among patients 0 to 3 months old. Children under 6.5 months old accounted for 80 % of the total patients infected by RSV. A negative correlation was found between ambient temperature and RSV infection, and it was strongest with minimum ambient temperature (r = ?0.804, P < 0.001). There was a positive correlation between the infection rate and the particulate matter (PM) 2.5 (r = 0.446, P < 0.001), PM10 (r = 0.397, P < 0.001), SO₂ (r = 0.389, P < 0.001), NO₂ (r = 0.365, P < 0.001) and CO (r = 0.532, P < 0.001). The current study suggested that temperature was an important factor associated with RSV infection among children in Hangzhou. Air pollutants significantly increased the risk of RSV infection with dosage, lag and cumulative effects.     

Particulates and Metallic Elements Monitoring at Two Sampling Sites (Harbor,Airport) in Taiwan

This study characterized the dry deposition flux and dry deposition velocity (Vd) of metallic elements attached on particulate matter. Specifically, large particles (>10 μm), coarse particles (10 μm～2.5 μm), and fine particles (<2.5 μm) were studied at the Gong Ming Junior High School (Taichung Airport) and Taichung Harbor sampling sites in central Taiwan. Ambient air samples were collected to determine total suspended particulate matter (TSP), dry deposition plate (DDP), Vd, coarse particulate matter (PM_2.5–10) and fine particulate matter (PM_2.5), and metallic elements concentrations at the Airport and Taichung Harbor sites between June 17, 2013, and November 14, 2013. The results revealed that the average TSP, DDP, Vd, PM_2.5–10, and PM_2.5 particulate at the Airport were 54.55 (μg/m³), 902.25 (μg/m²-min), 17.11 (m/sec), 0.003 (μg/m³), and 0.010 (μg/m³), respectively; while these values at Taichung Harbor were 63.66 (μg/m³), 539.69 (μg/m²-min), 9.94 (m/sec), 0.003 (μg/m³), and 0.014 (μg/m³), respectively. In addition, the results showed that the average Cu and Pb concentrations were higher than Cr, Ni, and Cd for both the airport and harbor sampling sites. Furthermore, Cr, N, Cu, Cd, and Pb had the highest average concentrations versus those reported for other study areas, with one exception: The results obtained in Kacanik, Kosovo, during 2005. The average metallic elements concentrations order was Cu > Pb > Cr > Ni > Cd.     

Sources and characteristics of carbonaceous aerosols at Agra “World heritage site” and Delhi “capital city of India”

Agra, one of the oldest cities “World Heritage site”, and Delhi, the capital city of India are both located in the border of Indo-Gangetic Plains (IGP) and heavily loaded with atmospheric aerosols due to tourist place, anthropogenic activities, and its topography, respectively. Therefore, there is need for monitoring of atmospheric aerosols to perceive the scenario and effects of particles over northern part of India. The present study was carried out at Agra (AGR) as well as Delhi (DEL) during winter period from November 2011 to February 2012 of fine particulate (PM_2.5: d?<?2.5 μm) as well as associated carbonaceous aerosols. PM_2.5 was collected at both places using medium volume air sampler (offline measurement) and analyzed for organic carbon (OC) and elemental carbon (EC). Also, simultaneously, black carbon (BC) was measured (online) at DEL. The average mass concentration of PM_2.5 was 165.42?±?119.46 μg m^?3 at AGR while at DEL it was 211.67?±?41.94 μg m^?3 which is ~27 % higher at DEL than AGR whereas the BC mass concentration was 10.60 μg m^?3. The PM_2.5 was substantially higher than the annual standard stipulated by central pollution control board and United States Environmental Protection Agency standards. The average concentrations of OC and EC were 69.96?±?34.42 and 9.53?±?7.27 μm m^?3, respectively. Total carbon (TC) was 79.01?±?38.98 μg m^?3 at AGR, while it was 50.11?±?11.93 (OC), 10.67?±?3.56 μg m^?3 (EC), and 60.78?±?14.56 μg m^?3 (TC) at DEL. The OC/EC ratio was 13.75 at (AGR) and 5.45 at (DEL). The higher OC/EC ratio at Agra indicates that the formation of secondary organic aerosol which emitted from variable primary sources. Significant correlation between PM_2.5 and its carbonaceous species were observed indicating similarity in sources at both sites. The average concentrations of secondary organic carbon (SOC) and primary organic carbon (POC) at AGR were 48.16 and 26.52 μg m^?3 while at DEL it was 38.78 and 27.55 μg m^?3, respectively. In the case of POC, similar concentrations were observed at both places but in the case of SOC higher over AGR by 24 in comparison to DEL, it is due to the high concentration of OC over AGR. Secondary organic aerosol (SOA) was 42 % higher at AGR than DEL which confirms the formation of secondary aerosol at AGR due to rural environment with higher concentrations of coarse mode particles. The SOA contribution in PM_2.5 was also estimated and was ~32 and 12 % at AGR and DEL respectively. Being high loading of fine particles along with carbonaceous aerosol, it is suggested to take necessary and immediate action in mitigation of the emission of carbonaceous aerosol in the northern part of India.     

Concentration and characterization of airborne particles in Tehran’s subway system

Particulate matter is an important air pollutant, especially in closed environments like underground subway stations. In this study, a total of 13 elements were determined from PM₁₀ and PM_2.5 samples collected at two subway stations (Imam Khomeini and Sadeghiye) in Tehran’s subway system. Sampling was conducted in April to August 2011 to measure PM concentrations in platform and adjacent outdoor air of the stations. In the Imam Khomeini station, the average concentrations of PM₁₀ and PM_2.5 were 94.4?±?26.3 and 52.3?±?16.5 μg m^?3 in the platform and 81.8?±?22.2 and 35?±?17.6 μg m^?3 in the outdoor air, respectively. In the Sadeghiye station, mean concentrations of PM₁₀ and PM_2.5 were 87.6?±?23 and 41.3?±?20.4 μg m^?3 in the platform and 73.9?±?17.3 and 30?±?15 μg m^?3, in the outdoor air, respectively. The relative contribution of elemental components in each particle fraction were accounted for 43 % (PM₁₀) and 47.7 % (PM_2.5) in platform of Imam Khomeini station and 15.9 % (PM₁₀) and 18.5 % (PM_2.5) in the outdoor air of this station. Also, at the Sadeghiye station, each fraction accounted for 31.6 % (PM₁₀) and 39.8 % (PM_2.5) in platform and was 11.7 % (PM₁₀) and 14.3 % (PM_2.5) in the outdoor. At the Imam Khomeini station, Fe was the predominant element to represent 32.4 and 36 % of the total mass of PM₁₀ and PM_2.5 in the platform and 11.5 and 13.3 % in the outdoor, respectively. At the Sadeghiye station, this element represented 22.7 and 29.8 % of total mass of PM₁₀ and PM_2.5 in the platform and 8.7 and 10.5 % in the outdoor air, respectively. Other major crustal elements were 5.8 % (PM₁₀) and 5.3 % (PM_2.5) in the Imam Khomeini station platform and 2.3 and 2.4 % in the outdoor air, respectively. The proportion of other minor elements was significantly lower, actually less than 7 % in total samples, and V was the minor concentration in total mass of PM₁₀ and PM_2.5 in both platform stations.