Creating an emission model based on portable emission measurement system for the purpose of a roundabout

Environmental Science and Pollution Research - Road transport is the main source of pollution to the environment in urban areas; therefore, there is a need to accurately estimate the amount of...     

On-road comparison of a portable emission measurement system with a mobile reference laboratory for a heavy-duty diesel vehicle

On-road comparisons were made between a mobile emissions laboratory (MEL) meeting federal standards and a portable emissions measurement system (PEMS). These comparisons were made over different conditions; including road grade, vibration, altitude, electric fields, and humidity with the PEMS mounted inside and outside of the tractor's cab. Brake-specific emissions were calculated to explore error differences between the MEL and PEMS during the Not-To-Exceed (NTE) engine operating zone. The PEMS brake-specific NOx (bsNOx) NTE emissions were biased high relative to the MEL and, in general, were about 8% of the 2007 in-use NTE NO_x standard of 2.68 g kW^?1 h^?1 (2.0 g hp^?1 h^?1). The bsCO₂ emissions for the PEMS were also consistently biased high relative to the MEL, with an average deviation of +4% ± 2%. NMHC and CO emissions were very low and typically less than 1% of the NTE threshold. This research was part of a comprehensive program to determine the “allowance” when PEMS are used for in-use compliance testing of heavy-duty diesel vehicles (HDDVs).     

Evaluation of bactericidal efficacy of silver ions on Escherichia coli for drinking water disinfection

Purpose

The purpose of this study is the development of a suitable process for the disinfection of drinking water by evaluating bactericidal efficacy of silver ions from silver electrodes.

Methods

A prototype of a silver ioniser with silver electrodes and control unit has been fabricated. Silver ions from silver electrodes in water samples were estimated with an atomic absorption spectrophotometer. A fresh culture of Escherichia coli (1.75?×?10³ c.f.u./ml) was exposed to 1, 2, 5, 10 and 20?ppb of silver ions in 100?ml of autoclaved tap water for 60?min. The effect of different pH and temperatures on bactericidal efficacy was observed at constant silver ion concentration (5?ppb) and contact time of 30?min.

Results

The maximum bactericidal activity (100%) was observed at 20?ppb of silver ion concentration indicating total disinfection after 20?min while minimum bactericidal activity (25%) was observed after 10?min at 01?ppb of silver ions. Likewise, 100% bactericidal activity was noticed with 2, 5 and 10?ppb of silver ions after 60, 50 and 40?min, respectively. Bactericidal activity at pH?5, 6, 7, 8 and 9 was observed at 79.9%, 79.8%, 80.5%, 100% and 100%, respectively, whereas it was 80.4%, 88.3%, 100%, 100% and 100% at 10°C, 20°C, 30°C, 40°C and 50°C, respectively.

Conclusion

The findings of this study revealed that very low concentrations of silver ions at pH?8?C9 and temperature >20°C have bactericidal efficacy for total disinfection of drinking water. Silver ionisation is suitable for water disinfection and an appropriate alternative to chlorination which forms carcinogenic disinfection by-products.     

Development of a new portable air sampler based on electrostatic precipitation

Airborne particles are known to cause illness and to influence meteorological phenomena. It is therefore important to monitor their concentrations and to identify them. A challenge is to collect micro and nanoparticles, microorganisms as well as toxic molecules with a device as simple and small as possible to be used easily and everywhere. Electrostatic precipitation is an efficient method to collect all kinds of airborne particles. Furthermore, this method can be miniaturized. A portable, silent, and autonomous air sampler based on this technology is therefore being developed with the final objective to collect very efficiently airborne pathogens such as supermicron bacteria but also submicron viruses. Particles are collected on a dry surface so they may be concentrated afterwards in a small amount of liquid medium to be analyzed. It is shown that nearly 98 % of airborne particles from 10 nm to 3 μm are collected.     

Enzyme-immunoassay techniques for the detection of atrazine in water samples: Evaluation of a commercial tube based assay

Environmental immunoassays can help lower the operating costs and improve the effectiveness of residue laboratories. The present study assesses the ability of a commercially available enzyme immunoassay (EIA) to detect triazine herbicides in water. The tube based EIA could detect atrazine in lake and river water with detection limits of 62 pg/mL and 180 pg/mL respectively. The assay's ability to quantify atrazine in a set of 124 water samples taken from many parts of Canada was compared with a reference method that used gas chromatographic separation combined with a nitrogen phosphorous detector (GC-NPD) (R=0.919). A 71 % reduction in analytical load was achieved at a threshold concentration of 1 ng/mL. There were 2.4 % false negative and 0.8 % false positive results associated with that load reduction. The variability of the assay control parameters was generally within two standard deviations of the mean response for 65 assays. The EIA for atrazine is recommended for use as a screening technique and as an inexpensive way to monitor triazine levels in waters that are known to be contaminated with those herbicides.     

Rapid detection of toxic metals in non-crushed oyster shells by portable X-ray fluorescence spectrometry

The aim of this study was the multi-elemental detection of toxic metals such as lead (Pb) in non-crushed oyster shells by using a portable X-ray fluorescence (XRF) spectrometer. A rapid, simultaneous multi-element analytical methodology for non-crushed oyster shells has been developed using a portable XRF which provides a quick, quantitative, non-destructive, and cost-effective mean for assessment of oyster shell contamination from Pb. Pb contamination in oyster shells was further confirmed by scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). The results indicated that Pb is distributed in-homogeneously in contaminated shells. Oyster shells have a lamellar structure that could contribute to the high accumulation of Pb on oyster shells.     

Evaluation of an SOS-Chromotest-based approach for the isolation and detection of sediment-associated genotoxins

A series of experiments was conducted to evaluate an approach advanced by the St. Lawrence Centre (SLC) of Environment Canada for assessing the genotoxic potential of sediments. The SLC method entails the extraction, isolation and solvent exchange of the organic constituents in sediment, and the testing of these solubilized extracts with the SOS Chromotest (Escherichia coli PQ37). A total of five sediments, three variously contaminated by organic compounds and two reference materials certified for persistent organic chemicals, were Soxhlet-extracted. Each of the five extracts was then split, with a portion remaining in crude form and another portion fractionated into two molecular-weight classes of organic contaminants, thus yielding a total of 15 extract samples. The ability of the SOS Chromotest to detect genotoxins in the various organic extracts was evaluated and compared with that of the Ames Fluctuation Assay (Salmonella typhimurium, strain TA100). The intra-laboratory variance associated with the SOS Chromotest was also assessed. Procedural details are presented and results are discussed. The SOS Chromotest results were in good agreement with those of the Ames Fluctuation Assay, especially after metabolic activation. However, the E. coli PQ37 system was slightly more sensitive than the Salmonella assay for detecting genotoxins in the sediment extracts. The SOS Chromotest was also the most discriminating of the two assays, generating SOS-induction factors that were consistent with the organic contamination gradient reported in the sediment samples. The removal of macromolecules from the dichloromethane extracts by size-exclusion chromatography prior to testing enhanced the sensitivity of both test systems. The intra-laboratory variance of the SOS Chromotest ranged from 0.24% to 23.82%, depending on the extract sample. As applied in this study, the SOS Chromotest can serve as a sensitive test for screening the genotoxic potential of uncharacterized sediment extracts. A more sensitive assay would be appropriate, however, as a confirmation for definitive investigations, especially for the detection of direct-acting genotoxins.     

Evaluation of the Galega-Rhizobium galegae system for the bioremediation of oil-contaminated soil

The bioremediation potential of a nitrogen-fixing leguminous plant, Galega orientalis, and its microsymbiont Rhizobium galegae was evaluated in BTX (benzene, toluene, xylene)-contaminated soils in microcosm and mesocosm scale. To measure the intrinsic tolerance of the organisms to m-toluate, a model compound representing BTX, G. orientalis and R. galegae were cultivated under increasing concentrations of m-toluate alone and in association with Pseudomonas putida pWWO, a bacterial strain able to degrade toluene-derived compounds. The test plants and rhizobia remained viable in m-toluate concentrations as high as 3000 ppm. Plant growth was inhibited in concentrations higher than 500 ppm, but restituted when plants were transferred into m-toluate-free medium. Nodulation was blocked under the influence of m-toluate, but was restored after the plants were transferred into the non-contaminated media. In the mesocosm assay the Galega plants showed good growth, nodulation and nitrogen fixation, and developed a strong rhizosphere in soils contaminated with oil or spiked with 2000 ppm m-toluate. Thus, this legume system has good potential for use on oil-contaminated sites     

Laboratory evaluation of an aldehyde scrubber system specifically for the detection of acrolein

We demonstrate the use of an aldehyde scrubber system to resolve isobaric aldehyde/alkene interferences in a proton transfer reaction mass spectrometer (PTR-MS) by selectively removing the aldehydes from the gas mixture without loss of quantitative information for the alkene components. The aldehyde scrubber system uses a bisulfite solution, which scrubs carbonyl compounds from the gas stream by forming water-soluble carbonyl bisulfite addition products, and has been evaluated using a synthetic mixture of acrolein and isoprene. Trapping efficiencies of acrolein exceeded 97%, whereas the transmission efficiency of isoprene was better than 92%. Quantification of the PTR-MS response to acrolein was validated through an intercomparison study that included two derivatization methods, dinitrophenylhydrazine (DNPH) and O-(4-cyano-2-ethoxybenzyl)hydroxylamine (CNET), and a spectroscopic method using a quantum cascade laser infrared absorption spectroscopy (QCL) instrument. Finally, using cigarette smoke as a complex matrix, the acrolein content was assessed using the scrubber and compared with direct QCL-based detection.     

Evaluation of the potential of laser-induced breakdown spectroscopy for detection of trace element in liquid

The analytical figure of merit of the potential of laser-induced breakdown spectroscopy (LIBS) has been evaluated for detection of trace element in liquid. LIBS data of Mg, Cr, Mn, and Re were studied. Various optical geometries, which produce the laser spark in and at the liquid sample, were tested. The calibration curves for Mg, Cr, Mn, and Re were obtained at the optimized experimental conditions with bulk liquid and in liquid jet. It was found that measurements using a liquid jet provide better detection limits than bulk liquid measurements. The limits of detection (LOD) of Mg, Cr, Mn, and Re in the present liquid jet measurement are found to be 0.1, 0.4, 0.7, and 8 ppm, respectively. The LOD of Mg using Mg 279.55 nm was compared with the values found in other liquid work.     

Evaluation of a multiresidue method for pesticides in cereals using supercritical fluid extraction and gas chromatographic detection

Supercritical fluid extraction (SFE) was evaluated to be applied for residue analysis of 22 gas chromatography/electron capture detector-nitrogen phosphorus detector (GC/ECD-NPD) amenable pesticides in rice, wild rice and wheat. Samples were extracted with supercritical carbon dioxide at 200 atm pressure and 50°C temperature, using methanol as a static modifier. Mean recoveries obtained with the proposed SFE method at two spiking levels with four replicates per level are compared with those obtained with an ethyl acetate-based solvent extraction/gel permeation chromatography (GPC) clean up method. Both methods gave consistent high recoveries for almost all the pesticides from all the commodities with overall mean recoveries higher than 70% with relative standard deviations lower than 20%. Remarkable exceptions were captafol and dimethoate, for which low and/or non-reproducible recoveries were obtained with the SFE method. Residue levels determined with both methods in nine different incurred samples of wheat, containing some of the studied pesticides, were very similar, but, in all cases, slightly higher levels were determined with the SFE method.     

On-road measurement of vehicle tailpipe emissions using a portable instrument

A study design procedure was developed and demonstrated for the deployment of portable onboard tailpipe emissions measurement systems for selected highway vehicles fueled by gasoline and E85 (a blend of 85% ethanol and 15% gasoline). Data collection, screening, processing, and analysis protocols were developed to assure data quality and to provide insights regarding quantification of real-world intravehicle variability in hot-stabilized emissions. Onboard systems provide representative real-world emissions measurements; however, onboard field studies are challenged by the observable but uncontrollable nature of traffic flow and ambient conditions. By characterizing intravehicle variability based on repeated data collection runs with the same driver/vehicle/route combinations, this study establishes the ability to develop stable modal emissions rates for idle, acceleration, cruise, and deceleration even in the face of uncontrollable external factors. For example, a consistent finding is that average emissions during acceleration are typically 5 times greater than during idle for hydrocarbons and carbon dioxide and 10 times greater for nitric oxide and carbon monoxide. A statistical method for comparing on-road emissions of different drivers is presented. Onboard data demonstrate the importance of accounting for the episodic nature of real-world emissions to help develop appropriate traffic and air quality management strategies.     

浙江省循环经济发展评价指标体系研究

近年来能源、土地及水资源短缺给浙江经济发展带来了极大的挑战,发展循环经济是实现可持续发展的重要途径.以循环经济为指导,结合浙江省循环经济发展现状,从减量化、资源化、无害化及社会经济发展四个控制层面构建浙江省循环经济发展指标体系,运用层次分析法对浙江省近8年的循环经济发展状况进行综合评价,旨在为浙江循环经济发展重点及方向提供科学依据.评价结果表明,浙江省循环经济发展水平逐年提高,呈良好发展趋势.     

Applicability of grid-net detection system for landfill leachate and diesel fuel release in the subsurface

The grid-net system estimating the electrical conductivity changes was evaluated as a potential detection system for the leakage of diesel fuel and landfill leachate. Aspects of electrical conductivity changes were varied upon the type of contaminant. The electrical conductivity in the homogeneous mixtures of soil and landfill leachate linearly increased with the ionic concentration of pore fluid, which became more significant at higher volumetric water contents. However, the electrical conductivity in soil/diesel fuel mixture decreased with diesel fuel content and it was more significant at lower water contents. The electrode spacing should be determined by considering the type of contaminant to enhance the electrode sensitivity especially when two-electrode sensors are to be used. The electrode sensitivity for landfill leachate was constantly maintained regardless of the electrode spacings while that for the diesel fuel significantly increased at smaller electrode spacings. This is possibly due to the fact that the insulating barrier effect of the diesel fuel in non-aqueous phase was less predominant at large electrode spacing because electrical current can form the round-about paths over the volume with relatively small diesel fuel content. The model test results showed that the grid-net detection system can be used to monitor the leakage from waste landfill and underground storage tank sites. However, for a successful application of the detection system in the field, data under various field conditions should be accumulated.     

Evaluation of flow injection analysis method with spectrophotometric detection for the determination of atrazine in soil extracts

A method for determining atrazine in soil extracts was evaluated by flow injection analysis with spectrophotometric detection. The method is based on the reaction of atrazine with pyridine in an acid medium followed by the reaction with NaOH and sulfanilic acid. Several analytical conditions were previously studied and optimized. Under the best conditions of analysis, the limits of detection and quantification were 0.15 and 0.45 mg L^?1, respectively, for a linear response between 0.50 and 2.50 mg L^?1, and a sampling throughput of 21 determinations per hour. Using the standard addition method, the maximum relative standard deviation of 17% and recovery values between 80 and 100% were observed for three extracts from soil samples with different composition. The proposed method is simple, low-cost and easy to use, and can be employed for studies involving atrazine in soil samples or for screening of atrazine in soils.     

Oxidation of organophosphorus pesticides for the sensitive detection by a cholinesterase-based biosensor

A potentiometric flow injection-type biosensor developed in our laboratory was used for the determination of organophosphorus pesticides (OPs). The principle of the biosensor is that the degree of inhibition of a sensor enzyme by an OP is dependent on the concentration of the pesticide. The sensor system consisted of a reactor with acetylcholinesterase (AChE) immobilized on a controlled pore glass and a detector with a tubular H(+)-selective membrane electrode. In order to examine the possibility of enhancing the sensitivity of the sensor by converting OPs to oxidized forms (stronger inhibitors), a comparison of the degree of enzyme inhibition by OPs at 10(-6) M before and after their oxidation was made. All of the ten pesticides tested exhibited greater inhibitory power toward the sensor enzyme following oxidation. All of the oxidized pesticides at 10(-6) M inhibited the sensor enzyme to a considerable degree, demonstrating the utility of the developed method for the class-specific determination of OPs. A calibration curve for diazinon, over the concentration range of 10(-11)-10(-4) M, was obtained. The lower detection limit was 2 x 10(-10) M. Treatment of the inhibited enzyme with pyridine-2-aldoxime restored the enzyme to near full activity, allowing repeated use of the sensor.     

Development of a Smoke Guide for the Evaluation of White Plumes

A smoke guide for use with white plumes has been developed by suspending size-graded industrial diamond dust in transparent plastic blocks. The guide consists of a series of four blocks containing dusts with white light transmittances of 20, 40, 60, and 80 per cent and scattering characteristics similar to those of white (oil) plumes commonly used for training smoke inspectors. The luminances of experimental plumes and guides with like transmittances are compared when viewed under different illuminating and viewing conditions. Similar tests with a U. S. Public Health Service Black Smoke Guide are also described.     

Application of a minicolumn detection method for screening spices for aflatoxin

The minicolumn of Holaday and Lansden was modified by increasing the height of neutral alumina and including a layer of anhydrous sodium sulphate. Using this procedure, aflatoxin was detected in 18 of 125 samples of black pepper, red pepper, ginger and turmeric. A few samples of each spice contained aflatoxin, although red pepper and turmeric showed the highest incidence. Aflatoxin B1 quantities ranged from 10 ug/kg to 120 ug/kg when estimated quantitatively by visual comparison with standards on thin-layer chromatography plates.     

Characterization of permanent fouling on the surfaces of UV lamps used for wastewater disinfection.

A significant problem with UV disinfection of wastewater is the accumulation of fouling materials at sleeve-water interfaces. It has been shown that automated chemical and/or mechanical cleaning can remove most fouling materials satisfactorily. However, permanent foulants, which cannot be removed completely by typical cleaning operations, always remain on the quartz sleeves. These permanent foulants reduce UV transmittance, in turn reducing disinfecting effectiveness. This research investigated the origins, formation, and composition of permanent fouling. Four instrumental analyses were used: atomic force microscope (AFM), X-ray fluorescence (XRF), scanning electron microscope combined with energy dispersive X-ray microanalysis (SEM/EDX), and sleeve UV transmittance (SUVT). It appeared that permanent foulants were trapped initially by microscale holes and peaks on fresh sleeve surfaces. Based on the topography and roughness measurements from the AFM, after long-term regular chemical and mechanical cleaning, the wipers of cleaning systems damage sleeve surfaces, creating scratches or holes with larger surface areas. Foulants are trapped more easily, and are attached tightly to the surfaces of these scratches or to each other. The results from XRF and SEM/EDX showed that the main fouling components were aluminum, iron, magnesium, calcium, and phosphorus. These could not be related to wastewater quality. For the specific cases studied, chemical plus mechanical cleaning is more effective in removing foulants and avoiding the accumulation of permanent foulants than mechanical cleaning alone; in most cases, SUVT was higher than 90% after chemical plus mechanical cleaning, whereas mechanical cleaning alone achieved only approximately 30% SUVT after long-term usage.     

Testing the efficacy of camera-trap sampling designs for monitoring giant pandas in a heterogeneous landscape

Environmental Science and Pollution Research - The use of camera traps is prevalent in the ecological study of giant pandas (Ailuropoda melanoleuca). The reliability of camera-trap surveying...