Photocatalytic decomposition of N<Subscript>2</Subscript>O over g-C<Subscript>3</Subscript>N<Subscript>4</Subscript>/WO<Subscript>3</Subscript> photocatalysts

Although the nitrous oxide belongs among three of the most contributing greenhouse gases to global warming, it is quite neglected by photocatalytic society. The g-C₃N₄ and WO₃ composites were therefore tested for the photocatalytic decomposition of N₂O for the first time. The pure photocatalysts were prepared by simple calcination of precursors, and the composites were prepared by mixing of suspension of pure components in water followed by calcination. The structural (X-ray diffraction, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoluminescence spectroscopy, photoelectrochemical measurements) of all composites were correlated with photocatalytic activity. The experimental results and results from characterization techniques confirmed creation of Z-scheme in the WO₃/g-C₃N₄ composites, which was confirmed by hydroxyl radicals’ trapping measurements. The photocatalytic decomposition of N₂O was carried out in the presence of UVA light (peak intensity at 365 nm) and the 1:2 WO₃/g-C₃N₄ composite was the most active one, but the photocatalytic activity was just negligibly higher than that of pure WO₃. This is caused by relatively weak interaction between WO₃ and g-C₃N₄ which was revealed from XPS.     

High-performance for hydrogen evolution and pollutant degradation of reduced graphene oxide/two-phase g-C<Subscript>3</Subscript>N<Subscript>4</Subscript> heterojunction photocatalysts

We have successfully synthesized the composites of two-phase g-C₃N₄ heterojunction photocatalysts by one-step method. And the reduced graphene oxide/two-phase g-C₃N₄ heterojunction photocatalyst was fabricated via a facile hydrothermal reduction method. The characterization results indicated that the two-phase g-C₃N₄ was integrated closely, and the common phenomenon of agglomeration for g-C₃N₄ was significantly reduced. Moreover, the oxidized graphene was reduced successfully in the composites and the graphene was overlaid on the surface or the interlayers of g-C₃N₄ heterojunction composite uniformly. In addition, we have carried out the photocatalytic activity experiments by H₂ evolution and rhodamine B removal, tetracycline removal under the visible light irradiation. The results revealed that the composite has improved the separation efficiency a lot than the pure photocatalyst. The photocurrent test demonstrated that the recombination of electrons and holes were efficiently inhibited as well as enhanced the photocatalytic activity. The 0.4% rGO loaded samples, 0.4% rGOCN2, own the best performance. Its rate of H₂ evolution was 15 times as high as that of the pure g-C₃N₄.     

Study on the removal of elemental mercury from simulated flue gas by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-CeO<Subscript>2</Subscript>/AC at low temperature

Fe₂O₃ and CeO₂ modified activated coke (AC) synthesized by the equivalent-volume impregnation were employed to remove elemental mercury (Hg⁰) from simulated flue gas at a low temperature. Effects of the mass ratio of Fe₂O₃ and CeO₂, reaction temperature, and individual flue gas components including O₂, NO, SO₂, and H₂O (g) on Hg⁰ removal efficiency of impregnated AC were investigated. The samples were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Results showed that with optimal mass percentage of 3 % Fe₂O₃ and 3 % CeO₂ on Fe3Ce3/AC, the Hg⁰ removal efficiency could reach an average of 88.29 % at 110 °C. Besides, it was observed that O₂ and NO exhibited a promotional effect on Hg⁰ removal, H₂O (g) exerted a suppressive effect, and SO₂ showed an insignificant inhibition without O₂ to some extent. The analysis of XPS indicated that the main species of mercury on used Fe3Ce3/AC was HgO, which implied that adsorption and catalytic oxidation were both included in Hg⁰ removal. Furthermore, the lattice oxygen, chemisorbed oxygen, and/or weakly bonded oxygen species made a contribution to Hg⁰ oxidation.     

Inactivation of <Emphasis Type="Italic">Escherichia coli</Emphasis> in fresh water with advanced oxidation processes based on the combination of O<Subscript>3</Subscript>, H<Subscript>2</Subscript>O<Subscript>2</Subscript>, and TiO<Subscript>2</Subscript>. Kinetic modeling

The purpose of this work was to study the efficiency of different treatments, based on the combination of O₃, H₂O₂, and TiO₂, on fresh surface water samples fortified with wild strains of Escherichia coli. Moreover, an exhaustive assessment of the influence of the different agents involved in the treatment has been carried out by kinetic modeling of E. coli inactivation results. The treatments studied were (i) ozonation (O₃), (ii) the peroxone system (O₃/0.04 mM H₂O₂), (iii) catalytic ozonation (O₃/1 g/L TiO₂), and (iv) a combined treatment of O₃/1 g/L TiO₂/0.04 mM H₂O₂. It was observed that the peroxone system achieved the highest levels of inactivation of E. coli, around 6.80 log after 10 min of contact time. Catalytic ozonation also obtained high levels of inactivation in a short period of time, reaching 6.22 log in 10 min. Both treatments, the peroxone system (O₃/H₂O₂) and catalytic ozonation (O₃/TiO₂), produced a higher inactivation rate of E. coli than ozonation (4.97 log after 10 min). While the combination of ozone with hydrogen peroxide or titanium dioxide thus produces an increase in the inactivation yield of E. coli regarding ozonation, the O₃/TiO₂/H₂O₂ combination did not enhance the inactivation results. The fitting of experimental values to the corresponding equations through non-linear regression techniques was carried out with Microsoft® Excel GInaFiT software. The inactivation results of E. coli did not respond to linear functions, and it was necessary to use mathematical models able to describe certain deviations in the bacterial inactivation processes. In this case, the inactivation results fit with mathematical models based on the hypothesis that the bacteria population is divided into two different subgroups with different degrees of resistance to treatments, for instance biphasic and biphasic with shoulder models.

Open image in new window

Graphical abstract ?

     

Potassium-based sorbents from fly ash for high-temperature CO<Subscript>2</Subscript> capture

Potassium-fly ash (K-FA) sorbents were investigated for high-temperature CO₂ sorption. K-FAs were synthesised using coal fly ash as source of silica and aluminium. The synthesised materials were also mixed with Li₂CO₃ and Ca(OH)₂ to evaluate their effect on CO₂ capture. Temperature strongly affected the performance of the K-FA sorbents, resulting in a CO₂ uptake of 1.45 mmol CO₂/g sorbent for K-FA 1:1 at 700 °C. The CO₂ sorption was enhanced by the presence of Li₂CO₃ (10 wt%), with the K-FA 1:1 capturing 2.38 mmol CO₂/g sorbent at 700 °C in 5 min. This sorption was found to be similar to previously developed Li-Na-FA (2.54 mmol/g) and Li-FA (2.4 mmol/g) sorbents. The presence of 10 % Li₂CO₃ also accelerated sorption and desorption. The results suggest that the increased uptake of CO₂ and faster reaction rates in presence of K-FA can be ascribed to the formation of K-Li eutectic phase, which favours the diffusion of potassium and CO₂ in the material matrix. The cyclic experiments showed that the K-FA materials maintained stable CO₂ uptake and reaction rates over 10 cycles.     

Synthesis of Fe-doped Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocatalyst and its sonophotocatalytic activity on synthetic dye and real textile wastewater

The catalysts such as Fe, Bi₂O₃, and Fe-doped Bi₂O₃ were synthesized for the sonophotocatalytic treatment of synthetic dye and real textile wastewater. The resultant catalysts were characterized for its size and uniform shape using x-ray diffractogram (XRD) and scanning electron microscopy (SEM) which signified the nanorod shape formed Bi₂O₃. The higher ultraviolet light absorbance capacity of the catalysts was also evident using diffuse reflectance spectroscopy (DRS). Initially, the effect of conventional parameters such as initial pH, gas bubbling (argon, oxygen, air and nitrogen) and oxidant addition (H₂O₂ and peroxymonosulfate) in the presence of sonolysis (22 and 37 kHz frequency) and photolysis (UV-C light) on 10 ppm Basic Brown 1 dye was studied. The results showed that highest decolorization of 62 % was attained for 3 g/L peroxymonosulfate under 37 kHz frequency sonolysis treatment. Secondly, with the catalyst study, highest of 46 % dye color removal was obtained with 4 g/L Fe under 37 kHz frequency sonolysis treatment. The sonophotocatalytic treatment of dye with Fe-doped Bi₂O₃ catalyst in combination with peroxymonosulfate showed highest color removal of 99 %. Finally, the sonophotocatalytic treatment of real textile wastewater in the presence of 3 g/L Fe-doped Bi₂O₃ and 6 g/L peroxymonosulfate reduced the total organic carbon (TOC) and chemical oxygen demand (COD) level to 77 and 91 %, respectively, in 180 min. The reported treatment process was found to treat the synthetic dye and real textile wastewater effectively.     

Photocatalytic degradation of phenol using Ag core-TiO<Subscript>2</Subscript> shell (Ag@TiO<Subscript>2</Subscript>) nanoparticles under UV light irradiation

Ag@TiO₂ nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO₂ nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO₂ nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading.     

Degradation of 2,4-D in soils by Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles combined with stimulating indigenous microbes

Purpose  

Degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) in soils by Fe₃O₄ nanoparticles combined with soil indigenous microbes was investigated, and the effects of Fe₃O₄ nanoparticles on soil microbial populations and enzyme activities were also studied.     

Effect of nuclear power on CO<Subscript>2</Subscript> emission from power plant sector in Iran

Introduction  

It is predicted that demand for electricity in Islamic Republic of Iran will continue to increase dramatically in the future due to the rapid pace of economic development leading to construction of new power plants. At the present time, most of electricity is generated by burning fossil fuels which result in emission of great deal of pollutants and greenhouse gases (GHG) such as SO₂, NO_x, and CO₂. The power industry is the largest contributor to these emissions. Due to minimal emission of GHG by renewable and nuclear power plants, they are most suitable replacements for the fossil-fueled power plants. However, the nuclear power plants are more suitable than renewable power plants in providing baseload electricity. The Bushehr Nuclear Power Plant, the only nuclear power plant of Iran, is expected to start operation in 2010. This paper attempts to interpret the role of Bushehr nuclear power plant (BNPP) in CO₂ emission trend of power plant sector in Iran.     

Hydrogen production using thermocatalytic decomposition of methane on Ni<Subscript>30</Subscript>/activated carbon and Ni<Subscript>30</Subscript>/carbon black

Hydrogen is an energy carrier of the future need. It could be produced from different sources and used for power generation or as a transport fuel which mainly in association with fuel cells. The primary challenge for hydrogen production is reducing the cost of production technologies to make the resulting hydrogen cost competitive with conventional fuels. Thermocatalytic decomposition (TCD) of methane is one of the most advantageous processes, which will meet the future demand, hence an attractive route for CO_x free environment. The present study deals with the production of hydrogen with 30 wt% of Ni impregnated in commercially available activated carbon and carbon black catalysts (samples coded as Ni₃₀/AC and Ni₃₀/CB, respectively). These combined catalysts were not attempted by previous studies. Pure form of hydrogen is produced at 850 °C and volume hourly space velocity (VHSV) of 1.62 L/h g on the activity of both the catalysts. The analysis (X-ray diffraction (XRD)) of the catalysts reveals moderately crystalline peaks of Ni, which might be responsible for the increase in catalytic life along with formation of carbon fibers. The activity of carbon black is sustainable for a longer time compared to that of activated carbon which has been confirmed by life time studies (850 °C and 54 sccm of methane).     

Photocatalytic degradation of dichlorvos in aqueous TiO<Subscript>2</Subscript> suspensions

Introduction  

In the present work, we explored the kinetics of dichlorvos (2,2-dichlorvinyl dimethyl phosphate, DDVP) decay through UV-A light-induced TiO₂ photocatalysis at pH 4 and 9, and the formation of degradation intermediates and final products under specific experimental conditions. Experimental observations and theoretical considerations allowed us to suggest the degradation mechanism of DDVP by the UV/TiO₂ process in aqueous solution.     

Effects of realistic concentrations of TiO<Subscript>2</Subscript> and ZnO nanoparticles in <Emphasis Type="Italic">Prochilodus lineatus</Emphasis> juvenile fish

The impact of nanoparticles on fish health is still a matter of debate, since nanotechnology is quite recent. In this study, freshwater benthonic juvenile fish Prochilodus lineatus were exposed through water to three concentrations of TiO₂ (0.1, 1, and 10 μg l^?1) and ZnO (7, 70, and 700 μg l^?1) nanoparticles, as well as to a mixture of both (TiO₂ 1 μg l^?1?+?ZnO 70 μg l^?1) for 5 and 30 days. Nanoparticle characterization revealed an increase of aggregate size in the function of concentration, but suspensions were generally stable. Fish mortality was high at subchronic exposure to 70 and 700 μg l^?1 of ZnO. Nanoparticle exposure led to decreased acetylcholinesterase activity either in the muscle or in the brain, depending on particle composition (muscle—TiO₂ 10 μg l^?1; brain—ZnO 7 and 700 μg l^?1), and protein oxidative damage increased in the brain (ZnO 70 μg l^?1) and gills (ZnO 70 μg l^?1 and mixture) but not in the liver. Exposed fish had more frequent alterations in the liver (necrosis, vascular congestion, leukocyte infiltration, and basophilic foci) and gills (hyperplasia and epithelial damages, e.g., epithelial disorganization and epithelial loss) than the control fish. Thus, predicted concentrations of TiO₂ and ZnO nanoparticles caused detectable effects on P. lineatus that may have important consequences to fish health. But, these effects are much more subtle than those usually reported in the scientific literature for high concentrations or doses of metal nanoparticles.     

Photocatalytic decomposition of methanol over La/TiO<Subscript>2</Subscript> materials

Lanthanum-modified TiO₂ photocatalysts (0.2–1.5 wt% La) were investigated in the methanol decomposition in an aqueous solution. The photocatalysts were prepared by the common sol-gel method followed by calcination. The structural (X-ray diffraction, Raman, X-ray photoelectron spectroscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoelectrochemical measurements) of all synthetized nanomaterials were correlated with photocatalytic activity. Both pure TiO₂ and La-doped TiO₂ photocatalysts proved higher yields of hydrogen in comparison to photolysis. The photocatalyst with optimal amount of lanthanum (0.2 wt% La) showed almost two times higher amount of hydrogen produced at the same time as in the presence of pure TiO₂. The photocatalytic activity increased with both increasing photocurrent response and decreasing amount of lattice and surface O species. It has been shown that both direct and indirect mechanisms of methanol photocatalytic oxidation participate in the production of hydrogen. Both direct and indirect mechanisms take part in the formation of hydrogen.     

Response of anaerobic membrane bioreactor to the presence of nano-Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript>: reactor performance,supernatant characteristics,and microbial community

Considering the increasing incorporation of manufactured nano-material into consumer products, there is a concern about its potential impacts in biological wastewater treatment. In this study, the response of anaerobic sludge to the presence of Bi₂WO₆ nano-particles (NPs) was investigated in the anaerobic membrane bioreactor (AnMBR). As the concentration of Bi₂WO₆ in the reactor was controlled around 1 mg/L, there was no significant difference in effluent water quality or bacterial activities before and after NP exposure, partially due to the microbial-induced NP aggregation and stable complex formation. However, with the increasing dosage of Bi₂WO₆ from 5 to 40 mg/L, great influences on the AnMBR performance were observed, including the reduction of COD removal efficiency, inhibition of the mechanization step, increased production of soluble microbial products, and enhanced secretion of extracellular polymer substrates. Additional investigation with high-throughput sequencing was conducted, clearly demonstrating that Bi₂WO₆ NPs induced changes in the bacterial community.     

Fullerol C<Subscript>60</Subscript>(OH)<Subscript>24</Subscript> nanoparticles and mycotoxigenic fungi: a preliminary investigation into modulation of mycotoxin production

Increased use of fullerols in various fields and expected increase of their environmental spread impose the necessity for testing fullerol nanoparticles (FNP) effects on microbiota. There is little information available on the interaction of mycotoxigenic fungi and FNP, despite FNP having a great potential of modifying mycotoxin production. Namely, FNP exhibit both ROS-quenching and ROS-producing properties, while oxidative stress stimulates mycotoxin synthesis in the fungi. In order to shed some light on the extent of interaction between FNP and mycotoxigenic fungi, the effects of fullerol C₆₀(OH)₂₄ nanoparticles (10, 100, 1000 ng/mL) on mycelial growth, aflatoxin production and oxidative stress modulation in an aflatoxigenic strain of Aspergillus flavus (NRRL 3251) during 168 h of incubation in a liquid culture medium were examined. FNP slightly reduced mycelial biomass weight, but significantly decreased aflatoxin concentration in media. Lipid peroxide content, superoxide dismutase, catalase and glutathione peroxidase activities suggest that FNP treatments hormetically reduced oxidative stress within fungal cells in turn suppressing aflatoxin production. These findings contribute to the assessment of environmental risk and application potential of fullerols.     

First assessment of the PM<Subscript>10</Subscript> and PM<Subscript>2.5</Subscript> particulate level in the ambient air of belgrade city

INTENTION, GOAL, SCOPE, BACKGROUND: As the strong negative health effect of exposure to the inhalable particulate matter PM10 in the urban environment has been confirmed, the study of the mass concentrations, physico-chemical characteristics, sources, as well as spatial and temporal variation of atmospheric aerosol particles becomes very important. OBJECTIVE: This work is a pilot study to assess the concentration level of ambient suspended particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade central urban area. Average daily concentrations of PM10 and PM2.5 have been measured at three representative points in the city between June 2002 and December 2002. The influence of meteorological parameters on PM10 and PM2.5 concentrations was analyzed, and possible pollution sources were identified. METHODS: Suspended particles were collected on Pure Teflon filters by using a Mini-Vol low-volume air sampler (Airmetrics Co., Inc.; 5 l min(-1) flow rate). Particle mass was determined gravimetrically after 48 h of conditioning in a desiccator, in a Class 100 clean room at the temperature T = 20 degrees C and at about 50% constant relative humidity (RH). RESULTS AND DISCUSSION: Analysis of the PM10 data indicated a marked difference between season without heating--(summer; mean value 56 microg m(-3)) and heating season--(winter; mean value 96 microg m3); 62% of samples exceeded the level of 50 microg m(-3). The impact of meteorological factors on PM concentrations was not immediately apparent, but there was a significant negative correlation with the wind speed. CONCLUSIONS: The PM10 and PM2.5 mass concentrations in the Belgrade urban area had high average values (77 microg m(-3) and 61 microg m(-3)) in comparison with other European cities. The main sources of particulate matter were traffic emission, road dust resuspension, and individual heating emissions. When the air masses are coming from the SW direction, the contribution from the Obrenovac power plants is evident. During days of exceptionally severe pollution, in both summer and winter periods, high production of secondary aerosols occurred, as can be seen from an increase in PM2.5 in respect to PM10 mass concentration. RECOMMENDATION AND OUTLOOK: The results obtained gave us the first impression of the concentration level of particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade ambient air. Due to measured high PM mass concentrations, it is obvious that it would be very difficult to meet the EU standards (EEC 1999) by 2010. It is necessary to continue with PM10 and PM2.5 sampling; and after comprehensive analysis which includes the results of chemical and physical characterization of particles, we will be able to recommend effective control measures in order to improve air quality in Belgrade.     

A mini-review on rare earth metal-doped TiO<Subscript>2</Subscript> for photocatalytic remediation of wastewater

Titanium dioxide (TiO₂) has been considered a useful material for the treatment of wastewater due to its non-toxic character, chemical stability and excellent electrical and optical properties which contribute in its wide range of applications, particularly in environmental remediation technology. However, the wide band gap of TiO₂ photocatalyst (anatase phase, 3.20 eV) limits its photocatalytic activity to the ultraviolet region of light. Besides that, the electron-hole pair recombination has been found to reduce the efficiency of the photocatalyst. To overcome these problems, tailoring of TiO₂ surface with rare earth metals to improve its surface, optical and photocatalytic properties has been investigated by many researchers. The surface modifications with rare earth metals proved to enhance the efficiency of TiO₂ photocatalyts by way of reducing the band gap by shifting the working wavelength to the visible region and inhibiting the anatase-to-rutile phase transformations. This review paper summarises the attempts on modification of TiO₂ using rare earth metals describing their effect on the photocatalytic activities of the modified TiO₂ photocatalyst.     

Photocatalytic reduction of carbon dioxide over Cu/TiO<Subscript>2</Subscript> photocatalysts

The photocatalytic reduction of CO₂ with H₂O was investigated using Cu/TiO₂ photocatalysts in aqueous solution. For this purpose, Cu/TiO₂ photocatalysts (with 0.2, 0.9, 2, 4, and 6 wt.% of Cu) have been synthesized via sol-gel method. The photocatalysts were extensively characterized by means of inductively coupled plasma optical emission spectrometry (ICP-OES), N₂ physisorption (BET), XRD, UV-vis DRS, FT-IR, Raman spectroscopy, TEM-EDX, and photoelectrochemical measurements. The as-prepared photocatalysts contain anatase as a major crystalline phase with a crystallite size around 13 nm. By increasing the amount of Cu, specific surface area and band gap energy decreased in addition to the formation of large agglomeration of CuO. Results revealed that the photocatalytic reduction of CO₂ decreased in the presence of Cu/TiO₂ in comparison to pure TiO₂, which might be associated to the formation of CuO phase acting as a recombination center of generated electron-hole pair. Decreasing of photoactivity can also be connected with a very low position of conduction band of photocatalysts with high Cu content, which makes H₂ production necessary for CO₂ reduction more difficult.     

Quantitative Evaluation of Electron Injection Efficiency in Dye-Sensitized TiO<Subscript>2</Subscript> Films

The efficiency of electron injection (Φ_inj) in dye-sensitized nanocrystalline films was studied through transient absorption (TA) and time-resolved microwave conductivity (TRMC) measurements. Here, I show the absolute value of Φ_inj for several dye-sensitized nanocrystalline films and discuss the relationship between Φ_inj and the free energy change (?ΔG _inj) for the injection process. Some systems exhibited lower Φ_inj values even when ?ΔG _inj was sufficiently large to promote electron injection. Recent experimental findings are used to propose possible explanations for this phenomenon. Quantitative evaluation of Φ_inj using TA and TRMC will give us new insights for developing high-performance solar cell devices.