Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

Graphene—a promising material for removal of perchlorate (ClO4 −) from water

A batch adsorption process was applied to investigate the removal of perchlorate (ClO₄ ^?) from water by graphene. In doing so, the thermodynamic adsorption isotherm and kinetic studies were also carried out. Graphene was prepared by a facile liquid-phase exfoliation. Graphene was characterized by Raman spectroscopy, Fourier-transform infrared spectroscopy, powder X-ray diffraction, scanning electron microscope, and zeta potential measurements. A systematic study of the adsorption process was performed by varying pH, ionic strength, and temperature. The adsorption efficiency of graphene was 99.2 %, suggesting that graphene is an excellent adsorbent for ClO₄ ^? removal from water. The rate constants for all these kinetic models were calculated, and the results indicate that second-order kinetics model was well suitable to model the kinetic adsorption of ClO₄ ^?. Equilibrium data were well described by the typical Langmuir adsorption isotherm. The experimental results showed that graphene is an excellent perchlorate adsorbent with an adsorbent capacity of up to 0.024 mg/g at initial perchlorate concentration of 2 mg/L and temperature of 298 K. Thermodynamic studies revealed that the adsorption reaction was a spontaneous and endothermic process. Graphene removed the perchlorate present in the water and reduced it to a permissible level making it drinkable.     

Oxidized multiwalled carbon nanotubes as adsorbent for the removal of manganese from aqueous solution

A batch adsorption process was applied to investigate the removal of manganese from aqueous solution by oxidized multiwalled carbon nanotubes (MWCNTs). In doing so, the thermodynamic, adsorption isotherm, and kinetic studies were also carried out. MWCNT with 5–10-nm outer diameter, surface area of 40–600 m²/g, and purity above 95 % was used as an adsorbent. A systematic study of the adsorption process was performed by varying pH, ionic strength, and temperature. Manganese-adsorbed MWCNT was characterized by Raman, FTIR, X-ray diffraction, XPS, SEM, and TEM. The adsorption efficiency could reach 96.82 %, suggesting that MWCNT is an excellent adsorbent for manganese removal from water. The results indicate that second-order kinetics model was well suitable to model the kinetic adsorption of manganese. Equilibrium data were well described by the typical Langmuir adsorption isotherm. Thermodynamic studies revealed that the adsorption reaction was spontaneous and endothermic process. The experimental results showed that MWCNT is an excellent manganese adsorbent. The MWCNTs removed the manganese present in the water and reduced it to a permissible level making it drinkable.     

Removal of arsenic species from water by batch and column operations on bagasse fly ash

Bagasse fly ash (BFA, a sugar industrial waste) was used as low-cost adsorbent for the uptake of arsenate and arsenite species from water. The optimum conditions for the removal of both species of arsenic were as follows: pH 7.0, concentration 50.0 μg/L, contact time 50.0 min, adsorbent dose 3.0 g/L, and temperature 20.0 °C, with 95.0 and 89.5 % removal of arsenate and arsenite, respectively. The Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich adsorption isotherms were used to analyze the results. The results of these models indicated single-layer uniform adsorption on heterogeneous surface. Thermodynamic parameters, i.e., ΔG°, ΔH°, and ΔS°, were also calculated. At 20.0 to 30.0 °C, the values of ΔG° lie in the range of ?4,722.75 to ?4,878.82 and ?4,308.80 to ?4,451.73 while the values of ΔH° and ΔS° were ?149.90 and ?121.07, and 15.61 and 14.29 for arsenate and arsenite, respectively, indicating that adsorption is spontaneous and exothermic. Pseudo-first-order kinetics was followed. In column experiments, the adsorption decreased as the flow rate increased with the maximum removal of 98.9 and 95.6 % for arsenate and arsenite, respectively. The bed depth service time and Yoon and Nelson models were used to analyze the experimental data. The adsorption capacity (N _o) of BFA on column was 3.65 and 2.98 mg/cm³ for arsenate and arsenite, respectively. The developed system for the removal of arsenate and arsenite species is economic, rapid, and capable of working under natural conditions. It may be used for the removal of arsenic species from any contaminated water resources.     

活化赤泥的除氟性能

以成本低的铝工业废矿渣（赤泥）为原材料,通过高温煅烧和酸化处理对赤泥进行活化,制备了除氟吸附剂。研究了反应时间、投加量、初始氟浓度、溶液温度、共存阴离子和pH值对活化赤泥除氟效果的影响。结果表明,接触反应时间为18 h时,吸附接近平衡。活化赤泥对氟离子的吸附符合Lagergren二级吸附动力学方程。另外,初始浓度越高,吸附容量越大。与Freundlich相比,Langmuir吸附等温模型可以更好地描述氟离子的吸附特性,最大吸附量可达2.71 mg/g。SO24-、Cl-和NO3-存在时（〈1 000 mg/L）,对氟离子的吸附几乎没有影响,然而,HCO3-、PO34-和氟离子共存时,会对氟吸附造成不利影响。活化赤泥在pH值3.5～11.0时,具有较好的吸附稳定性。活化赤泥是一种吸附容量高、性能稳定的环境友好型除氟材料,具有应用潜力。     

5种铁氧化物去除As(V)性能的比较研究

为了从铁氧化物中筛选得到潜在经济有效的除砷材料,对5种铁氧化物去除As(V)的性能进行了比较研究。吸附实验结果表明,其吸附容量依次为施氏矿物四方纤铁矿水铁矿赤铁矿针铁矿,其吸附过程均符合准二级动力学,约24 h时吸附达到平衡。其中,pH=5时,施氏矿物的吸附容量达到83 mg/g。分别投加500 mg/L和300 mg/L的施氏矿物,可将含砷1.484 mg/L和0.850 mg/L、高TOC含量和高pH特征的模拟配水砷浓度降至0.01 mg/L以下。鉴于施氏矿物良好的吸附除砷性能,进一步通过SEM、FTIR和电位滴定对其表面特性进行了深入研究,结果显示,本研究中制备的施氏矿物存在结构性或表面吸附的SO42-,其(质子)表面位密度约为4.32个/nm2,表面质子化常数pK1为4.60,pK2为-8.98。     

Removal of Disperse Red dye by bamboo-based activated carbon: optimisation, kinetics and equilibrium

This research involved the use of response surface methodology (RSM) to investigate the adsorption of Disperse Red 167 dye onto the bamboo-based activated carbon activated with H₃PO₄ (PBAC) in a batch process. F400, a commercially available activated carbon, was used in parallel for comparison. Analysis of variance showed that input variables such as the contact time, temperature, adsorbent dosage and the interaction between the temperature and the contact time had a significant effect on the dye removal for both adsorbents. RSM results show that the optimal contact time, temperature, initial dye concentration and adsorbent dosage for both adsorbents were found to be 15.4 h, 50 °C, 50.0 mg L^?1 and 12.0 g L^?1, respectively. Under these optimal conditions, the removal efficiencies reached 90.23 % and 92.13 % for PBAC and F400, respectively, with a desirability of 0.937. The validation of the experimental results confirmed the prediction of the models derived from RSM. The adsorption followed a nonlinear pseudo-first-order model and agreed well with the Freundlich and Temkin isotherm as judged by the levels of the AICc and the Akaike weight. Furthermore, the thermodynamics analysis indicated that, for both adsorbents, the adsorption was a physical process that was spontaneous, entropy-increasing and endothermic.     

Dynamic behaviour of Cd2+ adsorption in equilibrium batch studies by CaCO3 −-rich Corbicula fluminea shell

This work presents the structural and adsorption properties of the CaCO₃ ^?-rich Corbicula fluminea shell as a natural and economic adsorbent to remove Cd ions from aqueous solutions under batch studies. Experiments were conducted with different contact times, various initial concentrations, initial solution pH and serial biosorbent dosage to examine the dynamic characterization of the adsorption and its influence on Cd uptake capacity. The characterization of the C. fluminea shell using SEM/EDX revealed that the adsorbent surface is mostly impregnated by small particles of potentially calcium salts. The dominant Cd adsorption mechanism is strongly pH and concentration dependent. A maximum Cd removal efficiency of 96.20 % was obtained at pH 7 while the optimum adsorbent dosage was observed as 5 g/L. The Langmuir isotherm was discovered to be more suitable to represent the experimental equilibrium isotherm results with higher correlation coefficients (R ²?>?0.98) than Freundlich (R ²?<?0.97).The correlation coefficient values (p?<?0.01) indicated the superiority of the Langmuir isotherm over the Freundlich isotherm.     

Multi-component adsorption of copper,nickel and zinc from aqueous solutions onto activated carbon prepared from date stones

The removal of Cu²⁺, Ni²⁺, and Zn²⁺ ions from their multi-component aqueous mixture by sorption on activated carbon prepared from date stones was investigated. In the batch tests, experimental parameters were studied, including solution pH, contact time, initial metal ions concentration, and temperature. Adsorption efficiency of the heavy metals was pH-dependent and the maximum adsorption was found to occur at around 5.5 for Cu, Zn, and Ni. The maximum sorption capacities calculated by applying the Langmuir isotherm were 18.68 mg/g for Cu, 16.12 mg/g for Ni, and 12.19 mg/g for Zn. The competitive adsorption studies showed that the adsorption affinity order of the three heavy metals was Cu²⁺?>?Ni²⁺?>?Zn²⁺. The test results using real wastewater indicated that the prepared activated carbon could be used as a cheap adsorbent for the removal of heavy metals in aqueous solutions.     

Use of activated dry flowers (ADF) of Alstonia Scholaris for chromium (Vl) removal: equilibrium, kinetics and thermodynamics studies

In this study, a natural adsorbent (activated dry flowers (ADF)) was prepared from plant-derived waste biomass by chemical activation and employed for chromium (VI) removal from aqueous medium using experimental batch technique. Experiments were carried out as function of adsorbent dosage, pH, and contact time. The maximum chromium (Vl) removal was observed at initial pH 3 (~94 % removal). The equilibrium data was fitted well to Langmuir isotherm. The adsorption capacity of ADF was found to be 4.40 (mg chromium (Vl)/g) which was comparable to the adsorption capacity of some other adsorbents documented. Among various kinetic models applied, pseudo second-order model was found to explain the kinetics of chromium (VI) adsorption most effectively (R ² >0.99). Thermodynamic parameters such as ΔG, ΔS, and ΔH shows that adsorption process was spontaneous and endothermic at all the concentration ranges studied. Desorption of chromium (Vl) with 2 N NaOH was effective (~71 %) and, hence, there exists the possibility of recycling the ADF. The major advantages of using ADF as an adsorbent are due to its effectiveness in reducing the concentration of chromium (Vl) to very low levels. It requires little processing and is reversible as well as eco-friendly in contrast to traditional methods.     

Utilization of nSiO2, fly ash, and nSiO2/fly ash composite for the remediation of triphenyltin (TPT) from contaminated seawater

The removal of triphenyltin chloride from contaminated simulated seawater with adsorption method was discussed. The adsorbents used are fly ash, nSiO₂, and nSiO₂/fly ash composite. The results showed that the adsorption of the adsorbents increases with increase in the adsorbent dose, contact time, pH, stirring speed, initial TPT concentration, and decreased with increase in temperature. The adsorption fitted well with the Freundlich isotherm, showing that the adsorbent and TPT combined with function groups and the adsorption kinetics followed the pseudo-second-order kinetic model. The thermodynamic parameters were also evaluated. Optimal conditions for the adsorption of TPT from simulated seawater were applied to TPT removal from natural seawater. A higher removal efficiency of TPT (>99 %) was obtained for the nSiO₂/fly ash composite but not for fly ash and nSiO₂.     

Thermodynamic and kinetic studies of As(V) removal from water by zirconium oxide-coated marine sand

Arsenic contamination of groundwater is a major threat to human beings globally. Among various methods available for arsenic removal, adsorption is fast, inexpensive, selective, accurate, reproducible and eco-friendly in nature. The present paper describes removal of arsenate from water on zirconium oxide-coated sand (novel adsorbent). In the present work, zirconium oxide-coated sand was prepared and characterised by infrared and X-ray diffraction techniques. Batch experiments were performed to optimise different adsorption parameters such as initial arsenate concentration (100–1,000 μg/L), dose (1–8 g/L), pH of the solution (2–14), contact time (15–150 min.), and temperature (20, 30, 35 and 40 °C). The experimental data were analysed by Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. Furthermore, thermodynamic and kinetic parameters were evaluated to know the mode of adsorption between ZrOCMS and As(V). The maximum removal of arsenic, 97 %, was achieved at initial arsenic concentration of 200 μg/L, after 75 min at dosage of 5.0 g/L, pH?7.0 and 27?±?2 °C. For 600 μg/L concentration, the maximum Langmuir monolayer adsorption capacity was found to be 270 μg/g at 35 °C. Kinetic modelling data indicated that adsorption process followed pseudo-second-order kinetics. The mechanism is controlled by liquid film diffusion model. Thermodynamic parameter, ΔH°, was ?57.782, while the values of ΔG° were ?9.460, ?12.183, ?13.343 and ?13.905 kJ/mol at 20, 30, 35 and 40 °C, respectively, suggesting exothermic and spontaneous nature of the process. The change in entropy, ΔS°?=??0.23 kJ/mol indicated that the entropy decreased due to adsorption of arsenate ion onto the solid adsorbent. The results indicated that the reported zirconium oxide-coated marine sand (ZrOCMS) was good adsorbent with 97 % removal capacity at 200 μg/L concentration. It is interesting to note that the permissible limit of arsenic as per World Health Organization is 10 μg/L, and in real situation, this low concentration can be achieved through this adsorbent. Besides, the adsorption capacity showed that this adsorbent may be used for the removal of arsenic from any natural water resource.     

Microwave-assisted synthesis of hydroxyapatite for the removal of lead(II) from aqueous solutions

Purpose

This study has the objective to evaluate the lead(II) removal capacity of hydroxyapatite powder synthesized by microwave as an alternative method to decrease production time and cost.

Methods

Hydroxyapatite (HA) was synthesized by a microwave-assisted precipitation method using calcium nitrate and ammonium hydrogen phosphate as calcium and phosphorus sources, respectively. X-ray diffraction and Fourier transform infrared results clearly revealed that the resulting powder was HA with high purity and crystallinity. The obtained powder was used for the removal of lead(II) from aqueous solutions. The effects of pH, amount of adsorbent, initial lead(II) concentration, and contact time were studied in batch experiments.

Results

In the adsorption experiments, maximum lead(II) retention was obtained at pH 6. Adsorption equilibrium was established after 40 min. It was found that the adsorption of lead(II) on HA was correlated well (R ²?=?0.958) with the Freundlich equation for the concentration range studied. Both ion exchange and adsorption process were thought to exist in the removal process.

Conclusions

This study indicates that easily and rapidly synthesized HA by microwave-assisted precipitation method could be used as an efficient adsorbent for removal of lead(II) from aqueous solutions.     

Removal of Pb2+ from aqueous solution by adsorption on chemically modified muskmelon peel

A cost-effective biosorbent was prepared by a green chemical modification process from muskmelon peel by saponification with alkaline solution of Ca(OH)₂. Its adsorption behavior for lead ions was investigated and found to exhibit excellent adsorption properties. Results showed that the optimal equilibrium pH range for 100 % adsorption is from 4 up to 6.4. Adsorption equilibrium was attained within 10 min. The adsorption process can be described well by Langmuir model and pseudo-second-order kinetics equation, respectively. The maximum adsorption capacity for lead ions was found to be 0.81 mol/kg. Pectic acid contained in the muskmelon peel is the main factor responsible for the uptake of lead ions onto the gel, and the chemical modification process presented in this study can be assumed effective to prepare other similar biomaterials. The large adsorption capacity and the fast adsorption rate indicated that chemically saponified muskmelon peel gel in present study has great potential to be used as a cost-effective adsorbent for the removal of lead ions from the water.     

Studies on the removal of nickel from aqueous solutions using modified riverbed sand

This paper highlights the utility of riverbed sand (RS) for the treatment of Ni(II) from aqueous solutions. For enhancement of removal efficiency, RS was modified by simple methods. Raw and modified sands were characterized by scanning electron microscope (SEM), Energy Dispersive Spectroscopy (EDS), and Fourier Transform Infrared Spectroscopy (FTIR) to investigate the effect of modifying the surface of RS. For optimization of various important process parameters, batch mode experiments were conducted by choosing specific parameters such as pH (4.0–8.0), adsorbent dose (1.0–2.0 g), and metal ion concentrations (5–15 mg/L). Removal efficiency decreased from 68.76 to 54.09 % by increasing the concentration of Ni(II) in solution from 5 to 15 mg/L. Removal was found to be highly dependent on pH of aqueous solutions and maximum removal was achieved at pH 8.0. The process of removal follows first-order kinetics, and the value of rate constant was found to be 0.048 min^?1 at 5 mg/L and 25 °C. Value of intraparticle diffusion rate constant (k _id) was found to be 0.021 mg/g min^1/2 at 25 °C. Removal of Ni(II) decreased by increasing temperature which confirms exothermic nature of this system. For equilibrium studies, adsorption data was analyzed by Freundlich and Langmuir models. Thermodynamic studies for the present process were performed by determining the values of ΔG°, ΔH°, and ΔS°. Negative value of ?H° further confirms the exothermic nature of the removal process. The results of the present investigation indicate that modified riverbed sand (MRS) has high potential for the removal of Ni(II) from aqueous solutions, and resultant data can serve as baseline data for designing treatment plants at industrial scale.     

Adsorption of ammonium on biochar prepared from giant reed

Giant reed was used as precursor for making biochar in order for the adsorption of NH₄ ⁺–N from aqueous solution. And the adsorption of the product to NH₄ ⁺–N was examined. The surface features of biochar were investigated by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy/energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD). XRD patterns showed several peaks and correspond to the high amount of crystalline material. The crystals contain KCl, K₂O, CaO, MgO, and SiO and possess high surface area which enhances adsorption. The influence of different parameters such as initial concentration, adsorption time, pH, and ionic strength has been carried out. The adsorption could reach equilibrium through 24 h reaction and had the best adsorption amount at the solution pH values from 7 to 9. The cation has great influence on the adsorption of NH₄ ⁺–N, whereas the anion exerted a weaker effect. The adsorption followed pseudo-first-order and pseudo-second-order models. And the intraparticle diffusion and desorption studies further elucidated that the mechanism of adsorption on the product was ion exchange. The product equilibrium data was well described by the Langmuir and Freundlich model. The maximum adsorption capacities were 1.490 mg/g. Biochar derived from giant reed at 500 °C was suggested as a promising adsorbent for the removal of NH₄ ⁺–N from slightly polluted wastewater.     

Adsorption characteristics of Cu(II) from aqueous solution onto biochar derived from swine manure

The purpose of this study was to investigate adsorption characteristic of swine manure biochars pyrolyzed at 400 °C and 700 °C for the removal of Cu(II) ions from aqueous solutions. The biochars were characterized using BET surface area, Fourier transform infrared spectroscopy (FTIR), zeta potential, scanning electron microscopy/energy dispersive spectrometer (SEM–EDS), and X-ray diffraction (XRD). The adsorption of Cu(II) ions by batch method was carried out and the optimum conditions were investigated. The adsorption processes of these biochars are well described by a pseudo-second-order kinetic model, and the adsorption isotherm closely fitted the Sips model. Thermodynamic analysis suggested that the adsorption was endothermic. The maximum Cu(II) adsorption capacities of biochars derived from fresh and composted swine manure at 400 °C were 17.71 and 21.94 mg g^?1, respectively, which were higher than those at 700 °C. XRD patterns indicated that the silicate and phosphate particles within the biochars served as adsorption sites for Cu(II). The removal of Cu(II) ions from industrial effluent indicated that the fresh swine manure biochar pyrolyzed at 400 °C can be considered as an effective adsorbent.     

Modelling the adsorption of mercury onto natural and aluminium pillared clays

Introduction

The removal of heavy metals by natural adsorbent has become one of the most attractive solutions for environmental remediation. Natural clay collected from the Late Cretaceous Aleg formation, Tunisia was used as a natural adsorbent for the removal of Hg(II) in aqueous system.

Methods

Physicochemical characterization of the adsorbent was carried out with the aid of various techniques, including chemical analysis, X-ray diffraction, Fourier transform infrared and scanning electron micrograph. Batch sorption technique was selected as an appropriate technique in the current study. Method parameters, including pH, temperature, initial metal concentration and contact time, were varied in order to quantitatively evaluate their effects on Hg(II) adsorption onto the original and pillared clay samples. Adsorption kinetic was studied by fitting the experimental results to the pseudo-first-order and pseudo-second-order kinetic models. The adsorption data were also simulated with Langmuir, Freundlich and Temkin isotherms.

Results

Results showed that the natural clay samples are mainly composed of silica, alumina, iron, calcium and magnesium oxides. The sorbents are mainly mesoporous materials with specific surface area of <250 m² g^?1. From the adsorption of Hg(II) studies, experimental data demonstrated a high degree of fitness to the pseudo-second-order kinetics with an equilibration time of 240 min. The equilibrium data showed the best model fit to Langmuir model with the maximum adsorption capacities of 9.70 and 49.75 mg g^?1 for the original and aluminium pillared clays, respectively. The maximum adsorption of Hg(II) on the aluminium pillared clay was observed to occur at pH 3.2. The calculated thermodynamic parameters (?G°, ?H° and ?S°) showed an exothermic adsorption process. The entropy values varied between 60.77 and 117.59 J?mol^?1 K^?1, and those of enthalpy ranged from 16.31 to 30.77 kJ mol^?1. The equilibrium parameter (R _L) indicated that the adsorption of Hg(II) on Tunisian smectitic clays was favourable under the experimental conditions of this study.

Conclusion

The clay of the Aleg formation, Tunisia was found to be an efficient adsorbent for Hg(II) removal in aqueous systems.     

Evaluating of arsenic(V) removal from water by weak-base anion exchange adsorbents

Arsenic contamination of groundwater has been called the largest mass poisoning calamity in human history and creates severe health problems. The effective adsorbents are imperative in response to the widespread removal of toxic arsenic exposure through drinking water. Evaluation of arsenic(V) removal from water by weak-base anion exchange adsorbents was studied in this paper, aiming at the determination of the effects of pH, competing anions, and feed flow rates to improvement on remediation. Two types of weak-base adsorbents were used to evaluate arsenic(V) removal efficiency both in batch and column approaches. Anion selectivity was determined by both adsorbents in batch method as equilibrium As(V) adsorption capacities. Column studies were performed in fixed-bed experiments using both adsorbent packed columns, and kinetic performance was dependent on the feed flow rate and competing anions. The weak-base adsorbents clarified that these are selective to arsenic(V) over competition of chloride, nitrate, and sulfate anions. The solution pH played an important role in arsenic(V) removal, and a higher pH can cause lower adsorption capacities. A low concentration level of arsenic(V) was also removed by these adsorbents even at a high flow rate of 250–350 h^?1. Adsorbed arsenic(V) was quantitatively eluted with 1 M HCl acid and regenerated into hydrochloride form simultaneously for the next adsorption operation after rinsing with water. The weak-base anion exchange adsorbents are to be an effective means to remove arsenic(V) from drinking water. The fast adsorption rate and the excellent adsorption capacity in the neutral pH range will render this removal technique attractive in practical use in chemical industry.     

Effect of deposit age on adsorption and desorption behaviors of ammonia nitrogen on municipal solid waste

Ammonia nitrogen pollution control is an urgent issue of landfill. This research aims to select an optimal refuse for ammonia nitrogen removal in landfill from the point of view of adsorption and desorption behavior. MSW (municipal solid waste) samples which deposit ages were in the range of 5 to 15 years (named as R₁₅, R₁₁, R₇, and R₅) were collected from real landfill site. The ammonia nitrogen adsorption behaviors of MSW including equilibrium time, adsorption isotherms, and desorption behaviors including equilibrium time were determined. Furthermore, the effects of pH, OM, Cu(II), Zn(II), and Pb(II) on adsorption and desorption behavior of ammonia nitrogen were conducted by orthogonal experiment. The equilibrium time of ammonia nitrogen adsorption by each tested MSW was very short, i.e., 20 min, whereas desorption process needed 24 h and the ammonia nitrogen released from refuses was much lesser than that adsorbed, i.e., accounted for 3.20 % (R₁₅), 14.32 % (R₁₁), 20.59 % (R₇), and 20.50 % (R₅) of each adsorption quantity, respectively. The maximum adsorption capacity estimated from Langmuir isotherm appeared in R₁₅-KCl, i.e., 25,000 mg kg^?1. The best condition for ammonia nitrogen removal from leachate was pH >7.5, OM 23.58 %, Cu(II) <5 mg L^?1, Zn(II) <10 mg L^?1, and Pb(II) <1 mg L^?1. Ammonia nitrogen in landfill leachate could be quickly and largely absorbed by MSW but slowly and infrequently released. The refuse deposited for 15 years could be a suitable material for ammonia nitrogen removal.