EFFECTS OF INITIAL ABSTRACTION AND URBANIZATION ON ESTIMATED RUNOFF USING CN TECHNOLOGY1

ABSTRACT: Few studies have been conducted to explore the effects of initial abstraction on estimated direct runoff despite the widespread use of the curve number (CN) method in many hydrologic models to estimate direct runoff. In this study, use of a 5 percent ratio of initial abstraction (I_a) to storage (S) to estimate daily direct runoff with modified CN values for a 5 percent I_a/S value was investigated using the Long‐Term Hydrologic Impact Assessment (L‐THIA) geographic information system (GIS). In addition, the effects on estimated runoff of altering the hydrologic soil group due to urbanization were investigated. The L‐THIA model was applied to the Indiana Little Eagle Creek watershed with 5 percent and 20 percent I_a/S values, considering hydrologic soil group alteration due to urbanization. The results indicate that uses of a 5 percent l_a/S and modified CN values and Hydrologic Soil Group D for urbanized areas in model runs can improve long term direct runoff prediction.     

流域非点源分布式模型AnnAGNPS参数的不确定性研究

流域非点源分布式模型的不确定性研究成为目前的热点问题之一。本研究以宁波市章溪河流域为研究区,通过GIS软件AreView和AnnAGNPS模型,集成利用莫里斯分类筛选法,选取临界源面积、SCS曲线系数、水土保持因子、饱和导水率、氮磷吸收率、施肥量等6个因子进行敏感性分析。模拟结果表明,土壤饱和导水率、水土保持因子和径流曲线CN值对模型输出结果影响较大;水土保持因子对泥沙、总磷和总有机碳负荷的模拟结果影响最大,均呈显著负效应;径流曲线CN值对总氮负荷计算结果影响最大,呈显著正效应。     

COMPOSITE VS. DISTRIBUTED CURVE NUMBERS: EFFECTS ON ESTIMATES OF STORM RUNOFF DEPTHS1

ABSTRACT: The U.S. Department of Agriculture Curve Number (CN) method is one of the most common and widely used techniques for estimating surface runoff and has been incorporated into a number of popular hydrologic models. The CN method has traditionally been applied using compositing techniques in which the area weighted average of all curve numbers is calculated for a watershed or a small number of sub-watersheds. CN compositing was originally developed as a time saving procedure, reducing the number of runoff calculations required. However, with the proliferation of high speed computers and geographic information systems, it is now feasible to use distributed CNs when applying the CN method. To determine the effect of using composited versus distributed CNs on runoff estimates, two simulations of idealized watersheds were developed to compare runoff depths using composite and distributed CNs. The results of these simulations were compared to the results of similar analyses performed on an urbanizing watershed located in central Indiana and show that runoff depth estimates using distributed CNs are as much as 100 percent higher than when composited CNs are used. Underestimation of runoff due to CN compositing is a result of the curvilinear relationship between CN and runoff depth and is most severe for wide CN ranges, low CN values, and low precipitation depths. For larger design storms, however, the difference in runoff computed using composite and distributed CNs is minimal.     

A COMPUTERIZED DATA BASE FOR FLOOD PREDICTION MODELING1

ABSTRACT: A computerized geographic information system (GIS) was created in support of data requirements by a hydrologic model designed to predict the runoff hydrograph from ungaged basins. Some geomorphologic characteristics (i.e., channel lengths) were manually measured from topographic maps, while other parameters such as drainage area and number of channels of a specified order, land use, and soil type were digitized and manipulated through use of the GIS. The model required the generation of an integrated Soil Conservation Service (SCS) curve number for the entire basin. To this end, soil associations and land use (generated from analysis of Landsat satellite data) were merged in the GIS to acquire a map representing SCS runoff curve numbers. The volume of runoff obtained from the Watershed Hydrology Simulation (WAHS) Model using this map was compared to the volume computed by hydrograph separation and found to be accurate within 19 percent error. To quantify the effect of changing land use on basin hydrology, the GIS was used to vary percentages from the drainage area from forest to bare soil. By changing the basin runoff curve numbers, significant changes in peak discharge were noted; however, the time to peak discharge remained essentially independent of change in area of land use. The GIS capability eliminated many of the more traditional manual phases of data input arid manipulation, thereby allowing researchers to concentrate on the development and calibration of the model and the interpretation of presumably more accurate results.     

APPLICATION OF THE RHESSys MODEL TO A CALIFORNIA SEMIARID SHRUBLAND WATERSHED1

ABSTRACT: Distributed hydrologic models which link seasonal streamflow and soil moisture patterns with spatial patterns of vegetation are important tools for understanding the sensitivity of Mediterranean type ecosystems to future climate and land use change. RHESSys (Regional Hydro‐Ecologic Simulation System) is a coupled spatially distributed hydroecological model that is designed to be able to represent these feedbacks between hydrologic and vegetation carbon and nutrient cycling processes. However, RHESSys has not previously been applied to semiarid shrubland watersheds. In this study, the hydrologic submodel of RHESSys is evaluated by comparing model predictions of monthly and annual streamflow to stream gage data and by comparing RHESSys behavior to that of another hydrologic model of similar complexity, MIKESHE, for a 34 km² watershed near Santa Barbara, California. In model intercomparison, the differences in predictions of temporal patterns in streamflow, sensitivity of model predictions to calibration parameters and landscape representation, and differences in model estimates of soil moisture patterns are explored. Results from this study show that both models adequately predict seasonal patterns of streamflow response relative to observed data, but differ significantly in terms of estimates of soil moisture patterns and sensitivity of those patterns to the scale of landscape tessellation used to derive spatially distributed elements. This sensitivity has implications for implementing RHESSys as a tool to investigate interactions between hydrology and ecosystem processes.     

Effects of calibration on L-THIA GIS runoff and pollutant estimation

Urbanization can result in alteration of a watershed's hydrologic response and water quality. To simulate hydrologic and water quality impacts of land use changes, the Long-Term Hydrologic Impact Assessment (L-THIA) system has been used. The L-THIA system estimates pollutant loading based on direct runoff quantity and land use based pollutant coefficients. The accurate estimation of direct runoff is important in assessing water quality impacts of land use changes. An automated program was developed to calibrate the L-THIA model using the millions of curve number (CN) combinations associated with land uses and hydrologic soil groups. L-THIA calibration for the Little Eagle Creek (LEC) watershed near Indianapolis, Indiana was performed using land use data for 1991 and daily rainfall data for six months of 1991 (January 1-June 30) to minimize errors associated with use of different temporal land use data and rainfall data. For the calibration period, the Nash-Sutcliffe coefficient was 0.60 for estimated and observed direct runoff. The calibrated CN values were used for validation of the model for the same year (July 1-December 31), and the Nash-Sutcliffe coefficient was 0.60 for estimated and observed direct runoff. The Nash-Sutcliffe coefficient was 0.52 for January 1, 1991 to December 31, 1991 using uncalibrated CN values. As shown in this study, the use of better input parameters for the L-THIA model can improve accuracy. The effects on direct runoff and pollutant estimation of the calibrated CN values in the L-THIA model were investigated for the LEC. Following calibration, the estimated average annual direct runoff for the LEC watershed increased by 34%, total nitrogen by 24%, total phosphorus by 22%, and total lead by 43%. This study demonstrates that the L-THIA model should be calibrated and validated prior to application in a particular watershed to more accurately assess the effects of land use changes on hydrology and water quality.     

A PLANNING METHOD FOR EVALUATING DOWNSTREAM EFFECTS OF DETENTION BASINS1

While storm water detention basins are widely used for controlling increases in peak discharges that result from urbanization, recent research has indicated that under certain circumstances detention storage can actually cause increases in peak discharge rates. Because of the potential for detrimental downstream effects, storm water management policies often require downstream effects to be evaluated. Such evaluation requires the design engineer to collect additional topographic and land use data and make costly hydrologic analyses. Thus, a method, which is easy to apply and which would indicate whether or not a detailed hydrologic analysis of downstream impacts is necessary, should decrease the average cost of storm water management designs. A planning method that does not require either a large data base or a computer is presented. The time co-ordinates of runoff hydrographs are estimated using the time-of-concentration and the SCS runoff curve number; the discharge coordinates are estimated using a simple peak discharge equation. While the planning method does not require a detailed design of the detention basin, it does provide a reasonably accurate procedure for evaluating whether or not the installation of a detention basin will cause adverse downstream flooding.     

Impact of Residential Soil Disturbance on Infiltration Rate and Stormwater Runoff1

Woltemade, Christopher J., 2010. Impact of Residential Soil Disturbance on Infiltration Rate and Stormwater Runoff. Journal of the American Water Resources Association (JAWRA) 46(4): 700-711. DOI: 10.1111/j.1752-1688.2010.00442.x Abstract: Soil disturbances such as excavation and compaction in residential developments affect lawn infiltration rates and stormwater runoff. These effects were investigated via measuring saturated infiltration rates at 108 residential sites and 18 agricultural sites near Shippensburg, south-central Pennsylvania, using a double-ring infiltrometer. Residential sites included four neighborhoods distributed across three soil series classified as hydrologic soil group (HSG) B. Additional parcel data included date of house construction, percentage impervious area, lawn condition, and woody vegetation condition. Measured infiltration rates ranged from 0 to >40 cm/hour. Analysis of variance indicated significantly different mean infiltration rates (p < 0.001) for lots constructed pre-2000 (9.0 cm/hour) and those constructed post-2000 (2.8 cm/hour). Test results were used to determine a “field-tested” HSG for each site, representing disturbed soil conditions. Stormwater runoff was estimated from residential lots for a range of 24-hour design storms using the TR-55 model and several alternative methods of determining curve numbers, including five different representations of soil conditions. Curve numbers and stormwater runoff were substantially higher when based on field-tested HSGs for lots constructed post-2000 compared with lots built pre-2000 and when based on the HSG for undisturbed soils, documenting the magnitude of possible error in stormwater runoff models that neglect soil disturbance.     

Use of a geographic information system for storm runoff prediction from small urban watersheds

The use of computer-assisted map analysis techniques for prediction of storm runoff from a small urban watershed in the United States is investigated. An automated procedure for calculating input parameters for the US Soil Conservation Service (SCS) method of predicting storm runoff volume and peak timing is presented. Advanced techniques of spatial analysis are used to characterize spatial coincidence, surface configuration and effective hydrologic distance. A limited verification of the automated procedure indicates that the model reasonably characterizes water flow. A sensitivity analysis of basin disaggregation suggests that the SCS method yields increased volume and peak discharge predictions as the watershed is divided into smaller and smaller subunits. As a means to demonstrate the practical application of the automated procedure, a simulation of the effects on surface runoff for a potential residential development is presented.     

PLANNING OF URBAN BEST MANAGEMENT PRACTICES1

ABSTRACT: A “user-friendly” computer program has been developed for application in personal computers for preliminary design, evaluation, and cost effectiveness analysis of various best management practice (BMP) measures to control stormwater quantity and quality. The algorithms utilize the SCS TR-55 method for calculating runoff hydrographs for a single storm event and a first order pollutant washoff equation to generate pollutographs. Sensitivity analyses based on different policy scenarios is performed on a hypothetical watershed for the purpose of illustration. Three types of BMP measures, namely detention ponds (dry, wet, and extended wet ponds), infiltration trenches, and porous pavements are considered. It is found that the extended wet ponds have the best cost effective performance of the measures evaluated.     

EVALUATION OF THE APPLICABILITY OF THE SWAT MODEL FOR COASTAL WATERSHEDS IN SOUTHEASTERN LOUISIANA1

ABSTRACT: The Soil and Water Assessment Tool (SWAT) has been used for hydrologic analyses at various watershed scales. However, little is known about the model's performance in coastal watersheds. In this study SWAT was evaluated for its applicability in three Louisiana coastal watersheds: the Amite, Tickfaw, and Tangipahoa River watersheds. The model was calibrated with daily discharge from 1976 to 1977 and validated from 1979 to 1999 for the Amite and Tangipahoa and with daily discharge from 1979 to 1989 for the Tickfaw. Deviation of mean discharge and the Nash‐Sutcliffe model efficiency were used to evaluate model behavior. The study found that Manning's roughness coefficient for the main channel, SCS curve number, and soil evaporation compensation factor were the most sensitive parameters for these coastal watersheds. The Manning's roughness coefficient showed the greatest effect on the response time of surface runoff, suggesting the critical role of channel routing in hydrologic modeling for lowland watersheds. The SWAT model demonstrated an excellent performance, with Nash‐Sutcliffe efficiencies of 0.935, 0.940, and 0.960 for calibrations of the Amite, Tickfaw, and Tangipahoa watersheds, respectively, and of 0.851, 0.811, and 0.867 for validations. The modeling results demonstrate that SWAT is capable of simulating hydrologic processes for medium scale to large scale coastal lowland watersheds in Louisiana.     

History and Development of the NRCS Lag Time Equation1

Abstract: Many of the hydrologic methods that are used in engineering practice today resulted from the Spring Flood of 1936, which blanketed the Northeastern portion of the United States. Because of the flood damage that was caused by this rainfall‐snowmelt event, many federal agencies including the U.S. Army Corp of Engineers and the Soil Conservation Service (SCS) implemented the hydrologic theories that were available in the literature at this time and developed hydrologic procedures for design flow estimation. Sherman had recently published his unit hydrograph theory in 1932, and later in 1938 Snyder, who had been charged by the Water Resource Council to develop a synthetic unit hydrograph, published his famous paper. The SCS unit hydrograph theory was developed by Victor Mockus in the late 1950s. Most if not all of the theories at that time reported the rainfall‐runoff process for floods as a surface phenomenon, and as such those theories all required some type of a timing parameter to estimate watershed response time. This article documents the development of the SCS lag equation.     

PARTITIONING SMALL SCALE SPATIAL VARIABILITY OF RUNOFF AND EROSION ON SAGEBRUSH RANGELAND1

ABSTRACT: Most hydrologic models require input parameters which represent the variability found across an entire landscape. The estimation of such parameters is very difficult, particularly on rangeland. Improved model parameter estimation procedures are needed which incorporate the small-scale and temporal variability found on rangeland. This study investigates the use of a surface soil classification scheme to partition the spatial variability in hydrologic and interrill erosion processes in a sagebrush plant community. Four distinct microsites were found to exist within the sagebrush coppice-dune dune-interspace complex. The microsites explained the majority of variation in hydrologic and interrill erosion response found on the site and were discernable based on readily available soil and vegetation information. The variability within each microsite was quite low and was not well correlated with soil and vegetation properties. The surface soil classification scheme defined in this study can be quite useful for defining sampling procedures, for understanding hydrologic and erosion processes, and for parameterizing hydrologic models for use on sagebrush range-land.     

Runoff Curve Numbers at the Agricultural Field‐Scale and Implications for Continuous Simulation Modeling

This study used monitoring in the waterways of agricultural fields to understand the use of the runoff curve number (CN) in continuous simulation models. The CN has a long history as a design tool for estimating runoff volumes for large, single storms on small watersheds, but its use in continuous simulation models to describe runoff from smaller storms and relatively small areas is more recent and controversial. We examined 788 nonwinter rainfall events on four agricultural fields over five years (2004‐2008) during which runoff was generated in 87 events. The largest 20 runoff events on each field generated approximately 90% of the total runoff volume. The runoff event CNs showed an inverse correlation with storm depth that could not consistently be explained by previous precipitation. We review how small areas of higher runoff generation within larger areas will systematically increase the apparent CN of the larger area as the storm size decreases. If this variation is not incorporated into a model explicitly, continuous simulation modelers must understand that when source areas are aggregated or when runoff generation is spatially variable, the overall CN is not unique when smaller storms are included in the calibration set.     

ALAWAT: A spatially allocated watershed model for approximating stream,sediment, and pollutant flows in Hawaii,USA

The Ala Wai Canal Watershed Model (ALAWAT) is a planning-level watershed model for approximating direct runoff, streamflow, sediment loads, and loads for up to five pollutants. ALAWAT uses raster GIS data layers including land use, SCS soil hydrologic groups, annual rainfall, and subwatershed delineations as direct model parameter inputs and can use daily total rainfall from up to ten rain gauges and streamflow from up to ten stream gauges. ALAWAT uses a daily time step and can simulate flows for up to ten-year periods and for up to 50 subwatersheds. Pollutant loads are approximated using a user-defined combination of rating curve relationships, mean event concentrations, and loading/washoff parameters for specific subwatersheds, land uses, and times of year. Using ALAWAT, annual average streamflow and baseflow relationships and urban suspended sediment loads were approximated for the Ala Wai Canal watershed (about 10,400 acres) on the island of Oahu, Hawaii. Annual average urban suspended sediments were approximated using two methods: mean event concentrations and pollutant loading and washoff. Parameters for the pollutant loading and washoff method were then modified to simulate the effect of various street sweeping intervals on sediment loads.     

PCN BASED METAL PARTITIONING IN URBAN SNOWMELT,RAINFALL/RUNOFF,AND RIVER FLOW SYSTEMS1

ABSTRACT: Drawing an analogy between the popular Soil Conservation Service curve number (SCS‐CN) method based infiltration and metal sorption processes, a new partitioning curve number (PCN) approach is suggested for partitioning of heavy metals into dissolved and particulate bound forms in urban snowmelt, rainfall/runoff, and river flow environments. The parameters, the potential maximum desorption, ψ, and the PCN analogous to the SCS‐CN parameters S and CN, respectively, are introduced. Under the condition of snowmelt, PCN (or ψ) is found to generally rely on temperature, relative humidity, pH, and chloride content; during a rainstorm, ψ is found to depend on the alkalinity and the pH of the rainwater; and in the river flow situation, PCN is found to generally depend on the temperature, pH, and chloride content. The advantage of using PCN instead of the widely used partitioning parameter, K_d, is found to lie in the PCN's efficacy to distinguish the adsorption (or sorption) behavior of metals in the above snowmelt, rainfall/runoff, and river flow situations, analogous to the hydrological behavior of watersheds.     

Distributed Hydrologic Modeling in the Suburban Landscape: Assessing Parameter Transferability from Gauged Reference Catchments1

Mittman, Tamara, Lawrence E. Band, Taehee Hwang, and Monica Lipscomb Smith, 2012. Distributed Hydrologic Modeling in the Suburban Landscape: Assessing Parameter Transferability from Gauged Reference Catchments. Journal of the American Water Resources Association (JAWRA) 48(3): 546-557. DOI: 10.1111/j.1752-1688.2011.00636.x Abstract: Distributed, process-based models of catchment hydrologic response are potentially useful tools for the assessment of Low Impact Development (LID) techniques in urbanized catchments. Their application is often limited, however, by the lack of continuous streamflow records to calibrate poorly constrained parameters. This article examines the transferability of soil and groundwater parameters from a forested reference catchment to a nearby suburban catchment. We use the Regional Hydro-Ecologic Simulation System (RHESSys) to develop hydrologic models of one gauged forested and one ungauged suburban catchment within the Baltimore Ecosystem Study (BES) study area. We use a parameter uncertainty framework to calibrate soil and groundwater parameters for the forested catchment, and discrete measurements of streamflow from the suburban catchment to assess parameter transferability. Results indicate that the transfer of soil and groundwater parameters from forested reference to nearby suburban catchments is viable, with performance measures for the suburban catchment often exceeding those for the forested catchment. We propose that the simplification of hydrologic processes in urbanized catchments may account for the increase in model performance in the suburban catchment.     

PARAMETER UNCERTAINTY IN RAINFALL-RUNOFF MODELING FOR POLDER SYSTEM DESIGN1

ABSTRACT: An approach is developed for incorporating the uncertainty of parameters for estimating runoff in the design of polder systems in ungaged watersheds. Monte Carlo Simulation is used to derive a set of realizations of streamflow hydrographs for a given design rainstorm using the U. S. Soil Conservation Service (SCS) unit hydrograph model. The inverse of the SCS curve number, which is a function of the antecedent runoff condition in the SCS model, is the random input in the Monte Carlo Simulation. Monte Carlo realizations of streamfiow hydrographs are used to simulate the performance of a polder flood protection system. From this simulation the probability of occurrence of flood levels for a particular hydraulic design may be used to evaluate its effectiveness. This approach is demonstrated for the Pluit Polder flood protection system for the City of Jakarta, Indonesia. While the results of the application indicate that uncertainty in the antecedent runoff condition is important, the effects of uncertainty in rainfall data, in additional runoff parameters, such as time to peak, in the hydraulic design, and in the rainfall-runoff model selected should also be considered. Although, the SCS model is limited to agricultural conditions, the approach presented herein may be applied to other flood control systems if appropriate storm runoff models are selected.     

Assessing Watershed-Scale, Long-Term Hydrologic Impacts of Land-Use Change Using a GIS-NPS Model

Land-use change, dominated by an increase in urban/impervious areas, has a significant impact on water resources. This includes impacts on nonpoint source (NPS) pollution, which is the leading cause of degraded water quality in the United States. Traditional hydrologic models focus on estimating peak discharges and NPS pollution from high-magnitude, episodic storms and successfully address short-term, local-scale surface water management issues. However, runoff from small, low-frequency storms dominates long-term hydrologic impacts, and existing hydrologic models are usually of limited use in assessing the long-term impacts of land-use change. A long-term hydrologic impact assessment (L-THIA) model has been developed using the curve number (CN) method. Long-term climatic records are used in combination with soils and land-use information to calculate average annual runoff and NPS pollution at a watershed scale. The model is linked to a geographic information system (GIS) for convenient generation and management of model input and output data, and advanced visualization of model results. The L-THIA/NPS GIS model was applied to the Little Eagle Creek (LEC) watershed near Indianapolis, Indiana, USA. Historical land-use scenarios for 1973, 1984, and 1991 were analyzed to track land-use change in the watershed and to assess impacts on annual average runoff and NPS pollution from the watershed and its five subbasins. For the entire watershed between 1973 and 1991, an 18% increase in urban or impervious areas resulted in an estimated 80% increase in annual average runoff volume and estimated increases of more than 50% in annual average loads for lead, copper, and zinc. Estimated nutrient (nitrogen and phosphorus) loads decreased by 15% mainly because of loss of agricultural areas. The L-THIA/NPS GIS model is a powerful tool for identifying environmentally sensitive areas in terms of NPS pollution potential and for evaluating alternative land use scenarios for NPS pollution management.