Adsorption of Pb2+ and Cd2+ on the l-cysteine-functionalized graphene oxide/chitosan/polyvinyl alcohol hydrogel: Kinetic,isotherm, and thermodynamic study

In this study, polyvinyl alcohol-chitosan-cysteine-functionalized graphene oxide (PCCFG) hydrogel was synthesized from l -cysteine-functionalized graphene oxide (CFG), chitosan (CS), and polyvinyl alcohol (PVA). The hydrogel was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy and employed for removing lead ion (Pb²⁺) and cadmium ion (Cd²⁺) from aqueous solution. The effects of initial metal ion concentration, hydrogel dose, pH, time, and temperature were studied. The experimental data were well described by a pseudo-second-order kinetic model and Langmuir isotherm with maximum adsorption capacities of 250 and 192 mg g⁻¹ at 25°C for Pb²⁺ and Cd²⁺, respectively. The adsorption capacity of the PCCFG hydrogel increased with an increase in temperature. The value of ∆G° was negative, which shows the spontaneity of the reaction (electron exchange or ion exchange) between the metal ion and electron-rich atoms (–N, –S, –O). The positive ∆H° shows that the adsorption reaction consumes energy and the positive ∆S° shows the strong affinity of PCCFG toward the Pb²⁺ and Cd²⁺ ions. Pb²⁺ had better affinity and less spontaneity than Cd²⁺. The results show that the coexistence of Pb²⁺, Cd²⁺, and Cu²⁺ in the solution inhibits the adsorption capacity of PCCFG.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

Application of ameliorated wood pulp to recover Cd(II), Pb(II), and Ni(II) from e-waste

In this study, dl-malic acid and hydrogen peroxide were used as leaching agents to remove metals from e-waste (printed-circuit boards) and itaconic acid-grafted poly(vinyl alcohol)-encapsulated wood pulp (IA-g-PVA-en-WP) to uptake metals from leachate with high proficiency [11.63 mg g^?1; 93.03 % for Cd(II), 11.90 mg g^?1; 95.18 % for Pb(II), and 12.14 mg g^?1; 97.08 % for Ni(II)]. Metals were recovered from the loaded biosorbent by desorption studies. The standard analytical techniques, such as elemental analysis, Fourier-transform-infrared spectroscopy, scanning electron microscopy, atomic force microscopy, and thermogravimetric analysis, were used to characterize the recovering agent (biosorbent). At equilibrium, the metal uptake data were fitted to Langmuir and D–R isotherms (R ² > 0.99) significantly, revealing, the homogeneous distribution of active sites on biosorbent’s backbone. The possible mechanism appeared to be ion exchanges of metal ions with H⁺ together with binding over functionalities (COO^?). Dimensionless equilibrium parameter (R _L) showed the favourability of metal uptake at lower concentration, while mean adsorption energy (E) certified the physical binding of metal on functionalities which was further confirmed by sticking probability and activation energy parameters. Reusability studies were also conducted to state the performance of biosorbent.     

Itaconic Acid Grafted Starch Hydrogels as Metal Remover: Capacity,Selectivity and Adsorption Kinetics

Hydrogels were synthesized by free radical graft copolymerization of itaconic acid (IA) onto corn starch (S-g-IA). For this purpose, potassium permanganate (KMnO₄)-sodium bisulfite (NaHSO₃) was used as redox initiation system. The formation of grafted starches was confirmed by Fourier transform infrared spectroscopy, wide angle X-ray scattering, thermogravimetric analysis and scanning electron microscopy. The effect of monomer concentration, neutralization, addition of crosslinking agent, N,N-bismetilenacrilamide (MBAm), and initiator concentration on grafting efficiency and adsorption capacity of the starch hydrogels was investigated. It was demonstrated that the introduction of carboxyl and carbonyl groups promoted starch hydration and swelling. Grafting degree increased with the decrease of monomer concentration, increase of initiator concentration, grade of neutralization and the addition of MBAm without neutralization. Remarkably the resulting materials exhibited water absorption capacities between 258 and 1878% and the ability to adsorb metal ions. It was experimentally confirmed the metal uptake, obtaining the higher adsorption capacity (q _e  = 35 mg/g) for the product prepared with the pre-oxidation and lower initiator concentration. The removal capacity order was Pb²⁺>Ni²⁺>Zn²⁺>Cd²⁺. Moreover, the experimental kinetic and the equilibrium adsorption data for Ni²⁺ and Pb²⁺ were best fitted to the pseudo-second order and Freundlich isotherm models, respectively. This work describes for the first time the preparation of metal removal hydrogels based on starch and itaconic acid using the pair redox system KMnO₄/NaHSO₃, which avoids the starch hydrolysis and allows itaconic acid grafting incorporation without the requirement of more reactive comonomers.     

Preparation,Characterization, and Rapid Adsorption of Hg<Superscript>2+</Superscript> on Nanoscale Aramid-based Adsorbent

A series of nanaoscale aramid-based adsorbents were prepared by the functionalization of poly (p-phenylene terephthalamide) (PPTA) with different content of ethylenediamine (EDA). Their structures were characterized by field emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and elemental analysis. Metal ions, including Hg²⁺, Pb²⁺, Ag⁺, Cu²⁺, Cd²⁺, and Ni²⁺ were chosen as the models to explore the binding behaviors of PPTA–ECH–EDA in aqueous medium. Results showed that PPTA–ECH–EDA exhibited higher adsorption capacity for Hg²⁺ due to their nanoscale structures. In particular, the adsorption rate was so high that equilibrium was achieved within 15 min for Hg²⁺. The adsorption of Hg²⁺ on PPTA–ECH–EDA followed the pseudo second-order model well. Langmuir and Freundlich models were employed to fit the isothermal adsorption, and the results revealed that Freundlich isotherm was a better model to predict the experimental data. The adsorption mechanism was revealed by X-ray photoelectron spectroscopy. It is preconceived that PPTA–ECH–EDA could be used as an effective adsorbent for fast removal of heavy ions from wastewater.     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.     

Biosorptive removal of Pb(II) and Cu(II) from wastewater using activated carbon from cassava peels

The ability of activated carbon from cassava peels to remove heavy metals like Cu(II) and Pb(II) from hospital wastewater was investigated. The study showed that a pH of 8 was the best for the sorption of both metal ions onto the biosorbent. The time-dependent experiments for the metal ions showed that the binding of the metal ions to the biomass was rapid and occurred within 20–120 min. Sorption efficiency increased with a rise in adsorbent dosage. It increased from 12 to 73 % for Pb(II) and 26 to 79 % for Cu(II) when the adsorbent dose increased from 2 to 12 g. An increase in temperature led to an increase in sorption for both metal ions. The Langmuir model showed that the biomass has a higher sorption capacity for Cu(II) than Pb(II), with q _m = 5.80 mg g^?1 for Pb(II) and 8.00 mg g^?1 for Cu(II). The Freundlich isotherm K _f was 1.4 for Pb(II) and 1.8 for Cu(II), indicating a preferential sorption of Cu(II) onto the biosorbent. Adsorption capacity was found to decrease with an increase in particle sizes. Sorption occurred by physical mechanisms and was mainly controlled by intraparticle diffusion.     

Polymer Supported Calix[4]Arene Derivatives for the Extraction of Metals and Dichromate Anions

Three newly synthesized polymer supported calix[4]arene ionophores (7–9) were synthesized, and their ion binding properties toward selected alkali (Li⁺, Na⁺, K⁺, Cs⁺) and transition metal (Hg²⁺, Ni²⁺, Cu²⁺, Co²⁺, Cd²⁺, and Pb²⁺) cations were investigated. It has been observed that these ionophores are not selective toward a particular metal cation but show better ion binding property as compared to monomeric calixarene derivatives (2 and 6). Ionophore 6 and its supported polymer were also employed in dichromate anion extraction experiments. The polymeric ionophore (9) was found an effective extractant for dichromate anion even at pH 7.     

Synthesis of Ion-Imprinted Alginate Based Beads: Selective Adsorption Behavior of Nickel (II) Ions

Ni(II) imprinted and non-imprinted bioadsorbent alginate beads were prepared, and utilized in the selective adsorption of Ni(II) ions. The optimum adsorption capacity were 6.00 mmol g^?1 at 500 ppm initial metal ion concentration at pH 7 for Ni(II) imprinted alginate beads (IIP). The equilibrium data were applied to Langmuir and Freundlich adsorption isotherms, and it fitted both isotherm models. Thermodynamic parameters showed favorable and endothermic nature of adsorption. Ni(II) imprinted bead showed the strong ability to selective adsorption from Cu(II), Co(II) and Zn(II) ions. In conclusion, Ni(II) ion imprinted alginate beads could be used repeatedly without any significant reduce of adsorption capacity.     

Partial characterization of the exopolysaccharide from Oscillatoria trichoides Szafer and the role of released polysaccharide in sequestration of Cr6+

The structural investigation and the chromium adsorptive potential of an exopolysaccharide (EPS) released during the growth of an indigenous cyanobacterium, Oscillatoria trichoides Szafer, were investigated in a laboratory‐scale study. The results showed that, of the total EPS produced, 410.53 milligrams/gram (mg g^?1) were released polysaccharides (RPS) and 11.36 mg g^?1 were capsular polysaccharides (CPS). The sorption of hexavalent chromium (Cr⁶⁺) by the RPS achieved a maximum amount of metal removal (q_max) value of 76.92 mg g^?1 of polysaccharide dry weight. The highest coefficient of determination (0.9742) for the Langmuir adsorption model indicates best fitness of the model in explaining the sorption as a unilayer process. Equilibrium studies indicated that 30 to 40 milligrams per liter initial chromium concentration and a pH of 2 were optimal for biosorption of chromium by the RPS. Scanning electron microscopy with energy‐dispersive X‐ray spectroscopy analysis of Cr⁶⁺‐treated RPS showed the presence of 3.76% bound chromium. Compositional analysis of the EPS showed the presence of carbohydrates, proteins, pyruvic acid, and hexosamines. High‐performance liquid chromatography analysis demonstrated the presence of hexoses, as neutral sugars and glucuronic acid as an acidic sugar. The presence of carboxylic groups was also detected by infrared spectroscopy. The presence of these chemical constituents may serve as binding sites for the metal ions; therefore, the RPS of this species appears to be a promising biosorbent for Cr⁶⁺.     

Arsenic Removal from Dilute Solutions by High Surface Area Mesoporous Iron Oxyhydroxide

Mesostructured iron oxyhydroxide (FeO _x ) and iron oxyhydroxide–phosphate (FeO _x P) composites were organized using dodecylsulfate surfactant as a template. X-ray diffraction studies depicted a lamellar structure of the product. Ion exchange and solvent extraction methods were employed for the removal of the surfactant. Carboxylate ions exchanged lamellar type mesostructured material reorganized to a wormhole-like mesoporous material when heated under N₂ atmosphere. Surfactant was completely removed by carboxylate ions as observed by the Fourier transform infrared spectra. High surface area acetate-exchanged FeO _x (230 m² g^?1) was obtained after the surfactant removal from the composite (2.8 m² g^?1). Surface area of acetate-exchanged FeO _x P was the highest (240 m²g^?1) after the removal of the surfactant. Local structure of iron species of FeO _x was investigated by X-ray absorption fine structure spectroscopy. Further, Fe···Fe bond appeared at 3.21–3.25 Å with coordination number 2–3, showing a high degree of un-saturation of Fe···Fe bonds. As compared with bulk iron oxyhydroxide and iron-intercalated montmorillonite, the mesoporous iron materials were highly effective for arsenic removal from low concentrations of aqueous solutions. Furthermore, mesoporous iron materials were stable in aqueous phase.     

Poultry litter-based activated carbon for removing heavy metal ions in water

Utilization of poultry litter as a precursor material to manufacture activated carbon for treating heavy metal-contaminated water is a value-added strategy for recycling the organic waste. Batch adsorption experiments were conducted to investigate kinetics, isotherms, and capacity of poultry litter-based activated carbon for removing heavy metal ions in water. It was revealed that poultry litter-based activated carbon possessed significantly higher adsorption affinity and capacity for heavy metals than commercial activated carbons derived from bituminous coal and coconut shell. Adsorption of metal ions onto poultry litter-based carbon was rapid and followed Sigmoidal Chapman patterns as a function of contact time. Adsorption isotherms could be described by different models such as Langmuir and Freundlich equations, depending on the metal species and the coexistence of other metal ions. Potentially 404 mmol of Cu²⁺, 945 mmol of Pb²⁺, 236 mmol of Zn²⁺, and 250–300 mmol of Cd²⁺ would be adsorbed per kg of poultry litter-derived activated carbon. Releases of nutrients and metal ions from litter-derived carbon did not pose secondary water contamination risks. The study suggests that poultry litter can be utilized as a precursor material for economically manufacturing granular activated carbon that is to be used in wastewater treatment for removing heavy metals.     

Adsorption Efficiency of Polyaspartate-Montmorillonite Composite Towards the Removal of Pb(II) and Cd(II) from Aqueous Solution

The selective modification of sodium montmorillonite (Na⁺-Mt) surface with polyionene followed by poly (succinimde-co-aspartate) has been considered. Na⁺-Mt was allowed to react with well characterized polyionene in two fold excess. The resulting polyionene/Mt (IC) was further modified with poly (succinimide-co-aspartate) through an ion exchange process. The obtained polyaspartate/Mt (IPS) composite was characterized by elemental analysis, X-ray diffraction, FTIR spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and BET surface analyzer. The adsorption efficiency of IPS composite was investigated for the removal of Pb(II) and Cd(II) from aqueous solution under different experimental conditions including initial metal ions concentration, temperature and single and binary mixture systems of metal ions. The experimental data were analyzed by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models. Langmuir model reveals that the monolayer adsorption capacity of IPS was 92.59 and 67.57 mg/g for Pb(II) and Cd(II), respectively. The modification of parent Na⁺-Mt enhanced their adsorption capacity by about 87.91 and 29.84% for Pb(II) and Cd(II), respectively, due to inclusion of extra active sites of polyaspartate. The mean sorption energy, E calculated from Dubinin–Radushkevich isotherm were 2.75 and 1.98 kJ/mol for the adsorption of Pb(II) and Cd(II), respectively, indicating physical adsorption process. Also, The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic process. The mechanism of cation exchange and complexation of metal ions was suggested. IPS composite has a considerable potential for the removal of heavy metal ions from aqueous solution and wastewater stream.     

Sunflower stalk, an agricultural waste, as an adsorbent for the removal of lead and cadmium from aqueous solutions

Sunflower residue, an agricultural waste material for the removal of lead (Pb) and cadmium (Cd) from aqueous solutions were investigated using a batch method. Adsorbent was prepared by washing sunflower residue with deionized water until the effluent was colorless. Batch mode experiments were carried out as a function of solution pH, adsorbent dosage, initial concentration and contact time. The results indicated that the adsorbent showed good sorption potential and maximum metal removal was observed at pH 5. Within 150 min of operation about 97 and 87 % of Pb and Cd ions were removed from the solutions, respectively. Lead and Cd sorption curves were well fitted to the modified two-site Langmuir model. The adsorption capacities for Pb and Cd at optimum conditions were 182 and 70 mg g^?1, respectively. The kinetics of Pb and Cd adsorption from aqueous solutions were analyzed by fitting the experimental data to a pseudo-second-order kinetic model and the rate constant was found to be 8.42 × 10^?2 and 8.95 × 10^?2 g mg^?1 min^?1 for Cd and Pb, respectively. The results revealed that sunflower can adsorb considerable amount of Pb and Cd ions and thus could be an economical method for the removal of Pb and Cd from aqueous systems.     

Synthesis,Characterization and Application of α, β, and γ Cyclodextrin-Conjugated Graphene Oxide for Removing Cadmium Ions from Aqueous Media

In this study, a novel and facile route for the synthesis of cyclodextrin-conjugated graphene oxide (CDs–GO) nanocomposites by esterification reaction in the presence of EDC/DMAP as catalyst, was developed. The formation of CDs–GO was successfully approved by FT-IR, SEM, TEM, TGA and BET analyses. Then competitive adsorption capacity of cadmium ion by CDs–GO composites and the impact of different empirical parameters like contact time, initial metal ion concentration, and initial pH on the adsorption process were studied. The results showed that β-CD–GO at pH 7 is suitable for removing Cd(II) with 90?% removal efficiency. Also, the adsorption capacity experiment at constant concentration of 50 ppm of Cd(II) showed that more than 50?% of Cd(II) ions could be adsorbed by γ-CD–GO reaching an equilibrium within 2 h. Therefore, the γ-CD–GO and α-CD–GO showed high adsorption capacity toward Cd²⁺ (222.22 mg/g) which were pointedly more than that of β-CD–GO (208.33 mg/g). Furthermore, adsorption kinetics, isotherm studies, and thermodynamic analyses were evaluated. The adsorption data exhibited excellent fit to the pseudo-second-order (R²?>?0.99) and Freundlich isotherm models.

     

Adsorption of Ammonium by Graphene Oxide-Based Composites Prepared by UV Irradiation and Using as Slow-Release Fertilizer

A novel sodium alginate-grafted poly(acrylic acid)/graphene oxide (NaAlg-g-PAA/GO) composite hydrogel was prepared via ultraviolet irradiation, and characterized by infrared spectroscopy spectrometer. X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. It was employed to adsorb NH₄⁺ from aqueous solution and used as slow-release nitrogen fertilizers (SNFs). Result indicated that the adsorption process for NH₄⁺ reached equilibrium within 50 min, with the adsorption capacity of 6.6 mmol g^?1 even if 30 wt% GO was incorporated. The results of adsorption kinetic and isotherm were well described by the pseudo-second-order and Freundlich model. The thermodynamics analysis showed the adsorption process was spontaneous. The study indicated excellent water-holding ratio of soil with 2 wt% SNFs was 81.2%, and nitrogen release was up to 55.1% within 40 days in soil. Overall, NaAlg-g-PAA/GO could be considered as an efficient adsorbent for the recovery of nitrogen with the agronomic reuse as a fertilizer.     

Chitosan Functionalization with Amino Acids Yields to Higher Copper Ions Adsorption Capacity

Chitosan (Chi) beads were conjugated with three different amino acids [namely, glutamic acid (GLU), methionine (MET), and taurine (TAU)] aiming to increase the divalent copper ions uptake in aqueous media. Scanning Electron Microscopy evidenced the development of a large porous structure after amino acid functionalization, associated with the increase in a number of amino groups in the polymer backbone. X-Ray Photoelectron Spectroscopy and Fourier-Transform Infrared Spectra analyses were also employed to assess the conjugation of these three different amino acids in chitosan backbone. Adsorption experiments were conducted in a batch process, at 298 K, and kinetic data indicated a slightly better fitting for the pseudo-first-order model when compared to pseudo-second order. Intraparticle diffusion model suggested a three-step mechanism for Cu(II) adsorption kinetics, limited by the third step, the intraparticle diffusion. The isotherm data fitting to the traditional Langmuir and Freundlich models indicated a better fit for the former case. The amino acid conjugation resulted in the increase of the maximum adsorption capacity for Cu(II) from 1.30 mmol g^?1 prior to amino acid conjugation to values as high as 2.31 mmol g^?1, 2.40 mmol g^?1 and 2.68 mmol g^?1 for Chi–TAU, Chi–GLU, and Chi–MET, respectively. These results are attributed to the introduction of additional amino groups and new carboxylate and amino acid residues into the chitosan backbone, which might also be explored for amino acid demanding applications.     

Adsorption Kinetics of Dyes in Single and Binary Systems Using Cyanoguanidine-Crosslinked Chitosan of Different Deacetylation Degrees

The crosslinking of chitosan with cyanoguanidine shows some advantages, such as the improved the stability in acid solutions and the decrease of adsorbent cost. In this work, cyanoguanidine-crosslinked chitosan and pure chitosan were prepared to apply in the adsorption of Food Yellow 4 (FY4) and Food Blue 2 (FB2), in single and binary systems. Effects of pH and deacetylation degree (DD) of chitosan in adsorption were evaluated. The adsorbents were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The kinetic data were analyzed by pseudo-first order, pseudo-second order and Avrami models. The conditions of pH 3 and DD 95% were the more suitable to reach the highest adsorption capacities in all experimental assays. Under these conditions, the adsorption capacities for FY4 were approximately of 392 and 200 mg g^?1 and, for FB2 were approximately of 370 and 184 mg g^?1, respectively, in the single and binary systems. The Avrami model was suitable to represent the kinetic curves in all conditions, and the highest adsorption capacities were found for FY4 in binary aqueous system, being for the pure chitosan of 229 mg g^?1 and crosslinked chitosan of 218 mg g^?1. The Langmuir and extended Langmuir models presented a good fit to the equilibrium data in both systems. It was found that, the chitosan crosslinked with cyanoguanidine improved the chemical stability of chitosan as adsorbent.     

A case study of microwave processing of metal hydroxide sediment sludge from printed circuit board manufacturing wash water

The large quantity of wash water used in the electroplating and etching process in the manufacturing of printed circuit boards (PCBs) contains a high level of heavy metal ions (Cu⁺⁺, Zn⁺⁺, Ni⁺⁺, Cr⁺⁺⁺, Pb⁺⁺). These potentially toxic ions are removed from the wash water effluent through a polyelectrolyte flocculation and hydroxide precipitation process during which a hydroxide sediment sludge rich in metal ions and polymers is generated. This sediment sludge possesses some unique characteristics and properties in terms of composition, fine particle size distribution, high specific surface area, and a tendency to agglomerate after drying. Direct disposal of this classified “special waste” (Department of Environment of Northern Ireland, The Special Waste Regulations, Northern Ireland, 1998) at landfill sites may cause serious soil and underground water pollution through a gradual ionic leaching process. This paper describes an experimental investigation, exploratory in nature, which employs microwave radiation for detoxification of the sediment sludge through microwave heating, drying and metal ion immobilization within the sediment solids. The effectiveness of microwave assisted binding and immobilization of the metal ions within the sediment solids was studied in conjunction with an evaluation of microwave energy efficiency in comparison to the more conventional convective heating and drying processes. Given a sufficient amount of microwave radiation, leaching of Cu²⁺ and Pb²⁺ was reduced by 2700% and 1080%, respectively, over a period of 12 weeks, and further leaching was not detectable within six months at simulated local landfill aqueous conditions. This paper also attempts, through experimental observation, to add to the very limited understanding of the complex interactions and binding of free metal ions with the polymeric materials and metal hydroxides under the influence of an electromagnetic field. The high specific surface of the sediment solids and their adsorption properties were further explored and characterized in a study of adsorption of reactive dyes by the microwave processed solids.     

An Original Halo-Alkaline Protease from <Emphasis Type="Italic">Bacillus halodurans</Emphasis> Strain US193: Biochemical Characterization and Potential Use as Bio-Additive in Detergents

Over a hundred of halophilic/halotolerant microorganisms were screened for alkaline protease production. The bacterium showing the highest enzyme production was characterized and identified as Bacillus halodurans US193 on the basis of 16S rRNA gene analysis. It was alkalophilic, thermophilic and halotolerant since it grew optimally at pH 9.7 and 50?°C with tolerance of up to 125 g NaCl l^?1. The alkaline protease was purified 4.9 times with about 40186.1 U/mg as specific activity. It exhibited optimal activity at pH 10, 70?°C and 0.25 M NaCl with perfect stability at wide ranges of pH (6–12), temperatures (30–60?°C) and NaCl concentrations (0–2 M). The serine alkaline protease maintained high stability in the presence of Cu²⁺, Mg²⁺, Ba²⁺ and Ca²⁺ ions, various organic solvents [50% (v/v)] and ionic and non ionic detergent additives. In addition, it was more compatible with various commercialized detergents than other reported detergent proteases, and was very efficient in blood stain removal. These findings let B. halodurans US193 alkaline protease be an ideal candidate for many industrial processes at harsh conditions, especially as a bio-additive in detergent industry.