Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

Thermal and Mechanical Properties of Polyurethane Rigid Foam Based on Epoxidized Soybean Oil

A soypolyol based on epoxidized soybean oil (ESO) was prepared in the presence of HBF₄ and diethanolamine (DEA) was used as ring opener. A series of polyurethane rigid foam were prepared by mixing polyol with TDI using an isocyanate index of 1.1. The polyol used in this paper were a mixture of soypolyol and a commercial PL-5601 polyester polyol and the mass fraction of PL-5601 was in the range of 0–60%. The thermal properties of the resins were characterized by DSC and TG. The results showed that these rigid foams possess high thermal stability. There were two glass transition temperature of each foam and Tg₁ was increasing with the increasing of OH value. The compression strength of the foam was also recorded, and the effect of mass ratio of soypolyol and PL-5601 polyester polyol on the compression strength was discussed.     

Ionic Liquids as Environmentally Friendly Solvents in Macromolecules Chemistry and Technology,Part I

With the increasing emphasis on the environment and the need to find environmentally friendly solvent systems, ionic liquids (IL)s have been emerging as promising green solvents to replace conventional solvents in recent years. They possess unique properties such as nonvolatility, low toxicity, ease of handling, nonflammability and high ionic conductivity; thus they have received much attention as green media for various chemistry processes. This report provides an extensive overview of use of ILs in polymers chemistry and technology.     

Ionic Liquids as Environmentally Friendly Solvents in Macromolecules Chemistry and Technology,Part II

With the increasing emphasis on the environment and the need to find environmentally friendly solvent systems, ionic liquids (IL)s have been emerging as promising green solvents to replace conventional solvents in recent years. They possess unique properties such as nonvolatility, low toxicity, ease of handling, nonflammability and high ionic coductivity; thus they have received much attention as green media for various chemistry processes. This report provides an extensive overview of use of ILs in polymers chemistry and technology.     

Physical,Mechanical, and Morphological Characteristics of Extruded Starch Acetate Foams

Starch acetates with degrees of substitution (DS) of 0.57, 1.11, 1.68, and 2.23 were prepared and extruded with either water or ethanol. The microstructure, physical properties (radial expansion ratio [RER] and unit density), mechanical properties (spring index [SI] and compressibility), and crystalline structure of the foams were investigated. The functional properties were a function of DS and blowing agent type. When water was used as the blowing agent and DS increased, the foams were pale yellow, with rough and uneven surfaces. The cells were dense, with thick cell walls. Lower RER and SI, with higher DS, were associated with high unit density and compressibility. When ethanol was used as the blowing agent, contrary results were observed. The snow-white foams had smooth surfaces, uniform cells, and smooth cell walls. High RER and SI, and low unit density and compressibility were observed. The changes in SI and compressibility with RER also were examined and found to depend on the type of solvent. A crystalline pattern was observed because of the formation of well-ordered structures during extrusion.     

Thermal,Rheological, Mechanical and Morphological Behavior of High Density Polyethylene and Carboxymethyl Cellulose Blend

In this study water soluble sodium carboxymethyl cellulose (CMC) was blended with high density polyethylene (HDPE) by peroxide-initiated melt compounding technique. The compatibility of the blended polymers were carried out by silane crosslinking agent. A series of blends were prepared by varying the CMC contents up to a maximum of 50 phr. The physical properties of non-crosslinked and crosslinked blends were investigated in detail. FTIR analysis of crosslinked blend confirmed the presence of Si–O–Si and Si–O–C absorption peaks at 1050 and 1159 cm^?1. Thermal stability of crosslinked blends improved as compared to its non-crosslinked congener. Rheological study of crosslinked blends illustrated high complex viscosity and dynamic shear storage modulus. The tensile strength of virgin polyethylene was 8.1 MPa whereas the maximum tensile strength of 19.6 MPa was observed in crosslinked blend. Similarly lower deformation was observed in crosslinked blends under static load. Scanning electron microscopy of crosslinked formulations also showed strong adhesion between the polymers interface. The compatibility of HDPE and CMC is attributed to both free radical and condensation reactions.     

Thermal, Mechanical and Rheological Behavior of Poly(lactic acid)/Talc Composites

In the present study, influence of talc on thermal, mechanical and rheological behavior of PLA is investigated and the structure?Cproperty correlation for the PLA/talc composites is established. Poly(lactic acid)/talc composites are prepared by melt mixing of PLA with talc in twin screw extruder followed by blown film processing. Various characterizations techniques are used to evaluate thermal, morphological, mechanical and rheological behavior of PLA/talc composites and its blown film. DSC analysis showed that degree of crystallinity of PLA/talc composites was higher than that of neat PLA because of nucleating ability of talc. Spherulite morphology of PLA/talc composites showed that talc has increased nucleation density of spherulite having smaller radius than that of neat PLA. Talc is effective in enhancing tensile modulus and storage modulus of PLA due to reinforcing ability of talc particles.     

Biobased Polyurethanes from Rapeseed Oil Polyols: Structure, Mechanical and Thermal Properties

Biobased polyols were synthesized from rapeseed oil (RO) with diethanolamine (DEA), triethanolamine (TEA) and glycerol (GL) at different molar ratios. The structures of the synthesized polyols were analyzed using FTIR-ATR spectroscopy. Polyurethane (PU) networks from RO/DEA polyols and polymeric MDI showed higher tensile strength, modulus and hardness, but their elongation at break decreased, compared to the case of the PU obtained from RO/TEA and RO/GL polyols. The tensile strength and modulus of PU networks increased with increasing PU cohesion energy density (CED) and decreasing molecular weight between crosslinks M _c . From the thermogravimetric analysis and its derivative thermograms, at the first stage of destruction (below 5 % weight loss) in the air and inert atmosphere, the PU obtained from RO polyols were ranked in the following order: PU RO/GL > PU RO/TEA > PU RO/DEA, and their thermostability was higher than that of the PU based on propylene oxide.     

Synthesis and Characterization of Polyols and Polyurethane Foams from PET Waste and Crude Glycerol

In this study, polyethylene terephthalate (PET) waste from post-consumer soft-drink bottles and crude glycerol from the biodiesel industry were used for the preparation of polyols and polyurethane foams. PET waste was firstly depolymerized by the glycolysis of diethylene glycol. The glycolyzed PET oligomers were then reacted with crude glycerol at different weight ratios to produce polyols via a series of reactions, such as esterification, transesterification, condensation, and polycondensation. The polyols were characterized by titration, viscometry, gel permeation chromatography (GPC), and differential scanning calorimetry. Subsequently, polyurethane (PU) foams were made via the reaction between the produced polyols and polymeric methylene-4,4′-diphenyl diisocyanate and were characterized by mechanical testing, scanning electron microscopy, and thermogravimetric analysis. Polyols from crude glycerol and their PU foams were also prepared to compare properties with those of polyols and PU foams from PET and crude glycerol. The influence of aromatic segments existing in glycolyzed PET and glycerol content on the properties of the polyols and PU foams was investigated. It was found that aromatic segments of polyols from glycolyzed PET helped increase their molecular weights and improve thermal stability of PU foams, while high glycerol content in polyols increased the hydroxyl number of polyols and the density and compressive strength of PU foams.     

Dynamic Mechanical Behavior and Thermal Characterization of Biofilms Based on Starch Modified by Fungi Isolates

Starches modified by Ophiostoma spp. have been investigated to develop bio-materials with enhanced mechanical and physical properties for thermoplastic applications. In this study, glass transition temperature (T_g) of modified starches was investigated in both dynamic mechanical analyzer (DMA) and differential scanning calorimeter (DSC) to detect molecular changes in the starch’s structure. Overall, two thermal transitions were observed in modified starches, as opposed to one in their native counterparts. Scanning electron microscopy of granular modified starch indicated visible damages and internal structural perturbations in addition to occlusion of granular pores by extraneous materials owing to possible enzymatic degradation and production of secondary metabolites. Modified starches registered two-fold improvement in storage modulus as compared to that of native starches. From the study of second derivative of the mass loss against temperature, two thermal transitions were also identified in modified starches. X-ray diffraction analyses showed that crystalline regions of the starch granules remained intact after the modification. It is proposed that the second phase transition potentially corresponds to modified amylose fractions and/or exopolysaccharides produced by the fungi.     

Biobased Poly(1,3-propylene 2,5-furandicarboxylate)-Carbon Nanotubes Nanocomposites with Enhanced Thermal,Mechanical Properties and Crystallization Behavior

Journal of Polymers and the Environment - Biobased poly(1,3-propylene 2,5-furandicarboxylate) (PPF) and carbon nanotubes (CNTs) nanocomposites were prepared by a solution and coagulation method at...     

A Study of Dynamic Mechanical and Thermal Behavior of Starch/Poly(vinylalcohol) Based Films

Starch/Poly(vinylalcohol) blends in two different ratios (60:40 and 50:50) were prepared with glycerol as a plasticizer. Films were cast by a solution casting method. One set of films were filled with 10 wt% of bentonite clay and another set of films were crosslinked with epichlorohydrin in an alkaline medium. The prepared film samples were characterized with dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA). The presence of clay and crosslinking with epichlorohydrin was found to have considerable effect on the dynamic mechanical properties and thermal stability of the films. Intercomponent H-bonding between starch, Poly(vinylalcohol) and glycerol enhanced the thermal stability of the films. But incorporation of clay and crosslinking with epichlorohydrin enhanced the steric crowding and lowered the thermal stability of the films.     

Thermal and Environmentally Induced Degradation Behaviors of Amorphous and Semicrystalline PLAs Through Rheological Analysis

Journal of Polymers and the Environment - The degradation behaviors of an amorphous and a semicrystalline PLA (i.e., aPLA and cPLA) with similar molecular weights are compared at elevated...     

Hybridized Biocomposites from Agro-Wastes: Mechanical,Physical and Thermal Characterization

Agricultural wastes, oil palm trunk (OPT) veneer and oil palm empty fruit bunch (EFB) mat were used for the preparation of hybridized plywood using 250 and 450 g/m² of urea formaldehyde (UF) as gluing agent. The mechanical (flexural strength, flexural modulus, screw withdrawal, shear strength), physical (density, water absorption, thickness swelling and delamination) and thermal (TGA) properties of the biocomposites were studied. Images taken with a scanning electron micrograph (SEM) indicated an improvement in the fiber–matrix bonding for the laminated panel glued with 450 g/m² of UF.     

Biopolymers Based Green Composites: Mechanical, Thermal and Physico-chemical Characterization

Natural cellulosic fibers are one of the smartest materials for use as reinforcement in polymers possessing a number of applications. Keeping in mind the immense advantages of the natural fibers, in present work synthesis of natural cellulosic fibers reinforced polymer composites through compression molding technique have been reported. Scanning Electron microscopy (SEM), Thermo gravimetric/Differential thermal/Derivative Thermogravimetry (TGA/DTA/DTG), absorption in different solvents, moisture absorbance, water uptake and chemical resistance measurements were used as characterization techniques for evaluating the different behaviour of cellulosic natural fibers reinforced polymer composites. Effect of fiber loading on mechanical properties like tensile strength, flexural strength, compressive strength and wear resistances has also been determined. Reinforcing of the polymer matrix with natural fibers was done in the form of short fiber. Present work indicates that green composites can be successfully fabricated with useful mechanical properties. These composites may be used in secondary structural applications in automotive, housing etc.     

Molding Method, Thermal and Mechanical Properties of Jute/PLA Injection Molding

Natural composites have been important materials system due to preservation of earth environments. Natural fibers such as jute, hemp, bagasse and so on are very good candidate of natural composites as reinforcements. On the other hand regarding matrix parts thermosetting polymer and thermoplastic polymer deriver form petrochemical products are not environmental friendly material, even if thermoplastic polymer can be recycled. In order to create fully environmental friendly material (FEFM) biodegradable polymer which can be deriver from natural resources is needed. Therefore poly(lactic acid) (PLA) polymer is very good material for the FEFM. In this paper jute fiber filled PLA resin (jute/PLA) composites was fabricated by injection moldings and mechanical properties were measured. It is believable that industries will have much attention to FEFM, so that injection molding was adopted to fabricate the composites. Long fiber pellet fabricated by pultrusion technique was adopted to prepare jute/PLA pellet. Because it is able to fabricate composite pellets with relative long length fibers for injection molding process, where, jute yarns were continuously pulled and coated with PLA resin. Here two kinds of PLA materials were used including the one with mold releasing agent and the other without it. After pass through a heated die whereby PLA resin impregnates into the jute yarns and sufficient cooling, the impregnated jute yarns were cut into pellets. Then jute/PLA pellets were fed into injection machine to make dumbbell shape specimens. In current study, the effects of temperature of PLA melting temperature i.e. impregnation temperature and the kinds of PLA were focused to get optimum molding condition. The volume fractions of jute fiber in pellet were measured by several measuring method including image analyzing, density measurement and dissolution methods. Additionally, thermal and mechanical properties were investigated. It is found that 250° is much suitable for jute/PLA long fiber pultrusion process because of its less heat degradation of jute, better impregnation, acceptable mechanical property and higher production efficiency. Additionally the jute fibers seem much effective to increase deflection temperature under load, tensile modulus and Izod strength.     

Rheological, Mechanical and Thermal Behaviour of Wood Polymer Composites Based on Recycled Polypropylene

The aim of this paper was to investigate the effect of recycled polypropylene (PP) on the rheological, mechanical and thermal properties of wood flour polypropylene composites. Beforehand, the influence of wood flour treated with a coupling agent on the rheological behaviour had been looked at. By analysing moduli and viscosity curves and studying the thermal and mechanical properties of samples with 10% filler it was possible to see that the recycled PP that was added change in either its physical properties or its rheology. In the other wood plastic composites (WPC) studied, slight changes in the rheology behaviour were observed. However, the same processing parameters may be used with and without recycled PP. Recycled PP is appropriate for these kinds of composites to maintain the optimal rheological properties that make it easier to process the material by extrusion. Furthermore, it is also possible to maintain the thermal and mechanical properties in comparison with the behaviour of virgin PP/wood flour composites.     

Mechanical and Thermal Properties of Bamboo Microfibril Reinforced Polyhydroxybutyrate Biocomposites

In the present investigation, microfibrils were extracted from raw bamboo and characterized using scanning electron microscope. Composites based on polyhydroxybutyrate (PHB) and bamboo microfibril were prepared with various microfibril loading. The mechanical and thermal properties of the resulting composites were measured. Tensile strength and impact strength of the composites were found to be increasing with increase in the loading of bamboo microfibrils, reached an optimum and thereafter decreased with further increase in microfibril loading. Percentage crystallinity was found to be increasing with increase in fibril loading. Thermal stability of the composite was higher than that of pure PHB. The composite could be developed further for various structural applications.     

Silver Nanoparticle Incorporated Flaxseed Protein-Alginate Composite Films: Effect on Physicochemical,Mechanical, and Thermal Properties

Journal of Polymers and the Environment - In the present study, flaxseed protein-alginate films were prepared with different concentrations of silver nanoparticles (AgNPs) and were evaluated for...     

Mechanical, Thermal and Water Absorption Properties of Kenaf-Fiber-Based Polypropylene and Poly(Butylene Succinate) Composites

The use of composites made from non-biodegradable conventional plastic materials (e.g., polypropylene, PP) is creating global environmental concern. Biodegradable plastics such as poly(butylene succinate) (PBS) are sought after to reduce plastic waste accumulation. Unfortunately, these types of plastics are very costly; therefore, natural lignocellulosic fibers are incorporated to reduce the cost. Kenaf fibers are also incorporated into PP and PBS for reinforcing purposes and they have low densities, high specific properties and renewable sourcing. However without good compatibilization, the interfacial adhesion between the matrix and the fibers is poor due to differences in polarity between the two materials. Maleic anhydride-grafted compatibilizers may be introduced into the system to improve the matrix-fiber interactions. The overall mechanical, thermal and water absorption properties of PP and PBS composites prepared with 30 vol.% short kenaf fibers (KFs) using a twin-screw extruder were being investigated in this study. The flexural properties for both types of composites were enhanced by the addition of compatibilizer, with improvements of 56 and 16 % in flexural strength for the PP/KF and PBS/KF composites, respectively. Good matrix-fiber adhesion was also observed by scanning electron microscopy. However, the thermal stability of the PBS/KF composites was lower than that of the PP/KF composites. This result was confirmed by both DSC and TGA thermal analysis tests. The water absorption at equilibrium of a PBS composite filled with KFs is inherently lower than of a PP/KF composite because the water molecules more readily penetrate the PP composites through existing voids between the fibers and the matrix. Based on this research, it can be concluded that PBS/KF composites are good candidates for replacing PP/KF composites in applications whereby biodegradability is essential and no extreme thermal and moisture exposures are required.