The Effect of Acetylation on the Hydrolytic Degradation of PLA/Clay Nanocomposites

In this study, the hydrolytic degradation of Poly(lactic acid) (PLA) and acetylated PLA (PLA-Ac)–clay nanocomposites were investigated. The organo clay was obtained by ion exchange reaction using cetyl tri methyl ammonium bromide (CTAB). Nanocomposites containing 2, 5 and 8% mass ratio of organo clay (CTAB-O) were prepared. PLA and its organo clay nanocomposites were characterized by scanning electron microscope (SEM), thermo gravimetric analysis (TGA) and X-ray diffraction (XRD) to determine the morphology before and after hydrolytic degradation. Fourier transform infrared (FTIR) analyses of PLA and PLA-Ac were also obtained. The hydrolytic degradation of polymers and their composites were investigated in the phosphate buffered saline solution (PBS). The results showed that controlled hydrolytic degradation was observed in the samples with end group modification of PLA. While weight loss of PLA films was 28%, that of PLA-Ac films was 18% after 60 days degradation time. The weight loss was obtained as 29.5 and 25.5% for PLA-5 wt% organo clay (PLA/5CTAB-O) and PLA-Ac-5 wt% organo clay (PLA-Ac/5CTAB-O) nanocomposites films, respectively. It was also observed that thermal degradation of PLA-Ac was much more than that of PLA. Hydrolytic degradation increased depending on organo clay content. The end group modificated PLA results in controlled hydrolytic degradation. While hydrolytic degradation in polymer films occurred as surface erosion, bulk erosion was observed in composite films.     

Biodegradation of Polylactide and Gelatinized Starch Blend Films Under Controlled Soil Burial Conditions

The biodegradability of polylactide (PLA) and gelatinized starches (GS) blend films in the presence of compatibilizer was investigated under controlled soil burial conditions. Various contents (0–40 wt%) of corn and tapioca starches were added as fillers; whereas, different amounts of methylenediphenyl diisocyanate (MDI) (0–2.5 wt%) and 10 wt% based on PLA content of polyethylene glycol 400 (PEG400) were used as a compatibilizer and a plasticizer, respectively. The biodegradation process was followed by measuring changes in the physical appearance, weight loss, morphological studies, and tensile properties of the blend films. The results showed that the presence of small amount of MDI significantly increased the tensile properties of the blends compared with the uncompatibilized blends. This is attributed to an improvement of the interfacial interaction between PLA and GS phases, as evidenced by the morphological results. For soil burial testing, PLA/GS films with lower levels (1.25 wt%) of MDI had less degradation; in contrast, at high level of MDI, their changes of physical appearance and weight loss tended to increase. These effects are in agreement with their water absorption results. Furthermore, biodegradation rates of the films were enhanced with increasing starch contents, while mechanical performances were decreased.     

Experimental Investigation of Cellulose/Silver Nanocomposites Using In Situ Generation Method

Cellulose gel films were prepared by regeneration process using pre-cooled aq.(8 wt% LiOH + 15 wt% urea) mixture as solvent and ethyl alcohol as non solvent. The Terminus cattapa leaf extract diffused wet cellulose films were then dipped in 1–5 mM aq.AgNO₃ solutions to allow in situ generation of silver nanoparticles (AgNPs). Besides the in situ generation, some AgNPs were also formed outside the wet films in the solution. The AgNPs formed outside the films were observed under transmission electron microscope and scanning electron microscope. The nanocomposite films were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis and tensile test. The thermal stability of the composite films was lower than that of the matrix up to a temperature of ~300 °C and afterwards showed a reverse trend. The tensile strength of the nanocomposite films was found to be higher than the matrix but decreased with increasing concentration of aq.AgNO₃. The cellulose/AgNPs composite films showed good antibacterial activity against E. coli (gram positive) and Bacillus sp. (gram negative). Based on the aforementioned properties, the cellulose/AgNPs composite films can be considered for antibacterial packaging and medical applications.     

Blending Modification of PHBV/PCL and its Biodegradation by <Emphasis Type="Italic">Pseudomonas mendocina</Emphasis>

Poly(3-hydroxybutyrate-co-hydroxyvalerate) (PHBV) is a biodegradable polymer synthesized in microorganisms. The application of PHBV is limited by certain material disadvantages. Poly(ε-caprolactone) (PCL) possesses excellent thermodynamic and mechanical properties and was used to modify PHBV in the presence of triethyl citrate (TEC) and dicumyl peroxide (DCP), which was used as plasticizer and grafting agent, respectively. The effects of PCL and additive agents on the mechanical, thermal, amphipathic and degradability behaviors of the blends were investigated. The results showed that the mechanical properties of the PHBV blends improved by PCL incorporation and improved even further after TEC and DCP addition. The addition of DCP could not induce an increase in crystallization temperature but improved the crystallization degree of the blends. The presence of hydrophilic groups in TEC leads to an apparent increases in the hydrophilicity of the PHBV blends. A PHBV/PCL blend (40/60) with TEC (20 wt.%) and DCP (0.5 wt.%) was chosen for its good mechanical properties and hydrophilicity. The chosen ratio of the blends was also shown a preferable degradation activity by biodegradation assay using Pseudomonas mendocina. The addition of TEC and DCP has no conspicuous negative effect on the biodegradation.     

Stiff Biodegradable Polylactide Composites with Ultrafine Cellulose Filler

Polylactide (PLA) composites with 10–30 wt% of commercial fine grain filler of native cellulose were prepared by melt-mixing, and examined. The composite films had esthetic appearance, glossy surface, creamy color and density close to that of neat PLA. Good dispersion of the filler in PLA matrix was achieved. The composites were stiffer than neat PLA; in the glassy region the storage modulus increased by approx. 30 %. The tensile strength of the composite materials in the temperature range from 25 to 45 °C was similar to that of neat PLA. No marked decrease in molar mass of PLA in the composites occurred during processing in comparison to neat PLA. Moreover, thermogravimetry experiments demonstrated good thermal stability of the composites; 5 % weight loss occurred well above 300 °C.     

Biodegradation and Ecotoxicity of Polyethylene Films Containing Pro-Oxidant Additive

The worldwide accumulation of non-degradable plastic materials, such as plastic bags, is one of the most important environmental concerns nowadays. The use of degradable materials is an option to mitigate the environmental impact generated by the consumption of plastics. One of the technologies used for the manufacture and use of degradable plastics is the use of pro-degradant additives that are incorporated in conventional plastics to promote their degradation under certain conditions. The aim of this study is to evaluate the process of oxidation, biodegradation and potential ecotoxicity of polyethylene films containing an oxo-degradable additive, according to the standard ASTM D-6954. This method establishes a procedure in which the samples are subjected to consecutive steps of accelerated oxidation, biodegradation by composting and ecotoxicity assessment. Furthermore, the effect of the presence of printing ink in the polyethylene samples with oxo-degradable additive was evaluated, and the results were compared with those obtained for samples of conventional polyethylene and polylactic acid. After 180 days of laboratory controlled composting, the samples reached the following percentages of biodegradation: polylactic acid, 41 %; printed oxo-degradable polyethylene, 32.24 %; oxo-degradable polyethylene, 25.84 %; printed polyethylene, 18.23 % and polyethylene, 13.48 %. The cellulose sample used as a control was mineralized in 58.45 %. Ecotoxicity assessment showed that the products of biodegradation of the samples tested, did not generate a negative effect on germination or development of the vegetal species studied. Under proper waste management conditions, these plastics can be used as an option to decrease the environmental impact of plastic films.     

Thermocatalytic Degradation of High Density Polyethylene into Liquid Product

Thermocatalytic degradation of high density polyethylene (HDPE) was carried out using acid activated fire clay catalyst in a semi batch reactor. Thermal pyrolysis was performed in the temperature range of 420–500 °C. The liquid and gaseous yields were increased with increase in temperature. The liquid yield was obtained 30.1 wt% with thermal pyrolysis at temperature of 450 °C, which increased to 41.4 wt% with catalytic pyrolysis using acid activated fire clay catalyst at 10 wt% of catalyst loading. The composition of liquid products obtained by thermal and catalytic pyrolysis was analyzed by gas chromatography-mass spectrometry and compounds identified for catalytic pyrolysis were mainly paraffins and olefins with carbon number range of C₆–C₁₈. The boiling point was found in the range of commercial fuels (gasoline, diesel) and the calorific value was calculated to be 42 MJ/kg.     

Effect of Oxidized Starch on Morphology,Rheological and Tensile Properties of Low-Density Polyethylene/Linear Low-Density Polyethylene/Thermoplastic Oxidized Starch Blends

In this work, morphology, rheological and tensile properties of low-density polyethylene/linear low-density polyethylene/thermoplastic oxidized starch (LDPE/LLDPE/TPOS) blends are studied. The blends of LDPE/LLDPE (70/30, w/w) containing 0–20 wt% TPOS in the presence of 3 wt% of PE-grafted maleic anhydride (PE-g-MA) as a compatibilizer are prepared by a twin screw extruder and then converted to appropriate thin films using an extrusion film blowing machine. Scanning electron microscopic images show that there is a relative good dispersion of oxidized starch particles in PE matrices. However, as TPOS content in the blends increases, the starch particle size increases too. The rheological analyses indicate that TPOS can decrease the elasticity and viscosity of the blends. The LDPE/LLDPE/TPOS blends show power-law behavior and as the TPOS content increases the power-law exponent (n) and consistency index (K) decrease. The ultimate tensile strength and elongation at break of the final blend films reduce, when TPOS content increases from 5 to 20 wt%. However, the required mechanical properties for packaging applications are achieved when 10 wt% oxidized starch is added, according to ASTM D4635.     

Influence of Short Central PEO Segment on Hydrolytic and Enzymatic Degradation of Triblock PCL Copolymers

Hydrolytic, enzymatic degradation and composting under controlled conditions of series of triblock PCL/PEO copolymers, PCEC, with central short PEO block (M _n 400 g/mol) are presented and compared with homopolymer (PCL). The PCEC copolymers, synthesized via ring-opening polymerization of ε-caprolactone, were characterized by ¹H NMR, quantitative ¹³C NMR, GPC, DSC and WAXS. The introduction of the PEO central segment (<?2 wt%) in PCL chains significantly affected thermal degradation and crystallization behavior, while the hydrophobicity was slightly reduced as confirmed by water absorption and moisture uptake experiments. Hydrolytic degradation studies in phosphate buffer after 8 weeks indicated a small weight loss, while FTIR analysis detected changes in crystallinity indexes and GPC measurements revealed bulk degradation. Enzymatic degradation tested by cell-free extracts containing Pseudomonas aeruginosa PAO1 confirmed high enzyme activity throughout the surface causing morphological changes detected by optical microscopy and AFM analysis. The changes in roughness of polymer films revealed surface erosion mechanism of enzymatic degradation. Copolymer with the highest content of PEO segment and the lowest molecular weight showed better degradation ability compared to PCL and other copolymers. Furthermore, composting of polymer films in a model compost system at 37 °C resulted in significant degradation of the all synthesized block copolymers.     

Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/Organomodified Montmorillonite Nanocomposites for Potential Food Packaging Applications

Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) is a versatile, biobased and biodegradable copolymer from the family of polyhydroxyalkanoates. This study aims to further ameliorate its properties in order to enhance its applicability for food packaging purposes through preparation of organomodified montmorillonite clay (OMMT) nanocomposites. Nanocomposites based on pure PHBHHx as well as commercial PHBHHx granulate, after a previous dry-mixing with OMMT in concentrations of 1, 3, 5 and 10 wt%, were prepared using melt blending and compression molding. Investigation of the samples showed well dispersed nanofiller and highly intercalated nanocomposites, resulting in a continuous decrease in gas permeability, lowering O₂, CO₂ and water vapor permeability with about 5–7 % and approximately 40 % at OMMT concentration of 1 and 10 wt%, respectively. Besides gas permeability, other properties were affected as well. Thermal stability of the samples increased gradually up to 5 wt% nanofiller, but was reduced at 10 wt%. In order to investigate the effects of OMMT and molecular weights on PHBHHx crystallization, nanocomposites were also produced by solvent-casting and compared to those obtained by melt-blending. Crystallization was retarded, because of severe lowering of molecular weight due to processing-induced chain scission, catalyzed by OMMT moisture. However, this reduction was counteracted for a large part by using commercial PHBHHx granulate, which has shown better crystallization properties. The samples were rendered increasingly more brittle, displaying higher Young’s modulus and severely reduced elongation at break. From this study it appeared that, upon viewing all affected properties as a whole, the sample based on commercial PHBHHx and containing 3 wt% OMMT shows most promise for possible applications, however further research must be performed in order to exploit their fullest potential.     

Effects of fly ash addition on physical properties of porous clay-fly ash composites via polymeric replica technique

The porous composites of clay and fly ash have the potential to be used in many fields, such as catalyst support and gas adsorbents. In this study, various ratios of fly ash (1–2) with different percentage of suspension (50–70 wt%) were applied to produce porous clay-fly ash composites via polymeric replica technique. Fabrication process starts by mixing clay and fly ash in distilled water to form slurry. The process is followed by fully immersing polymer sponge in slurry. The excess slurry is then removed through squeezing. Finally, the sponge coated with slurry is sintered at 500 and 1250 °C for 1 h. It is found that the compressive strength of porous composites improves significantly (0.178–1.28 MPa) when the amount of clay-fly ash suspension mixture (50–70 wt%) increases. The compressive strength of porous composites is mainly attributed to the mullite, quartz and amorphous phase formations. These results are supported by X-ray diffraction analysis. On the other hand, increase in the amount of suspension reduces the apparent density (from 2.44 to 2.32 g/cm³) and porosity (from 97 to 85 %). The reduction in apparent density is believed to be caused by the presence of high fly ash content in porous composites. The melted fly ash cenospheres have closed the internal pores and increased density of samples. Higher suspension level not only reduces porosity, but also increases close pores of the porous composites. The results are justified through the observation from the structures of porous clay-fly ash composites.     

The Effect of Gamma and Electron Beam Irradiation on the Biodegradability of PLA Films

Biodegradation of poly(lactic) acid (PLA) has been studied extensively, but there is only limited knowledge about the effect of irradiation sterilization on its biodegradability. The aim of this work was to examine the aerobic biodegradation of gamma and electron beam irradiated PLA films along with the effects of aging (3, 6, and 9 months of storage) using a direct measurement respirometric system. Commercial PLA film was exposed to a simulated aerobic compost environment, and its mineralization was 96 % at day 85. Gamma and electron beam irradiation affected the biodegradation of the post-irradiated PLA film. Aging irradiated PLA had some potential to increase the biodegradation rate, as the average value of mineralization after 9 months of storage was higher than for the non-irradiated PLA. Comparison of the effect of storage time on the biodegradability of PLA showed a significant increase in biodegradation of the gamma irradiated PLA after 3 months (70 %) and 9 months of storage (130 %). Similarly, there was a significant difference in the biodegradation of electron beam irradiated PLA between 3 months (68 %) and 9 months of storage (120 %). Due to the priming effect, the percent mineralization of gamma irradiated and E-beam irradiated PLA after 9 months of storage was greater than 100 %. Both non-irradiated and irradiated PLA films can be considered biodegradable plastics since they showed mineralization percentage larger than 90 % of that of the positive control at the end of the test period.     

Synthesis and Properties Modified Feather Keratin-Based Motor Oil Sorbing Cryogels with High Oil Holding Capacity

Oleic acid was used to modify keratin extracted from chicken feathers by free radical initiated graft copolymerization. Thereafter, the modified keratin was used for the synthesis of cryogels. The influence of oleic acid modification, the crosslinker content, and the protein concentration on the properties of the cryogels were investigated by Fourier transform infrared spectroscopy, scanning electron microscopy, SDS-PAGE, and through oil holding capacity tests. To enhance the sorption properties, the cryogels were crosslinked with glutaraldehyde. Varying protein concentration from 1.27 to 5.09 wt% and glutaraldehyde concentration from 0 to 5 wt% produced cryogels with oil holding capacity ranging from 4.56 to 10.76 g/g. The highest results exceeded the sorption capacity of previously published oleic acid modified woodchips (6.3 g/g) as well as polypropylene (6 g/g), which is the standard material used in industry.     

Fabrication of Admicelled Natural Rubber by Polycaprolactone for Toughening Poly(lactic acid)

Natural rubber (NR) with polycaprolactone (PCL) core–shell (NR-ad-PCL), synthesized by admicellar polymerization, was acted as an impact modifier for poly(lactic acid) (PLA). PLA and NR-ad-PCL were melt-blended using a co-rotating twin screw extruder. The morphology of PLA/NR-ad-PCL blends showed good adhesion as smooth boundary around rubber particles and PLA matrix. Only 5 wt% of rubber phase, NR-ad-PCL was more effective than NR to enhance toughness and mechanical properties of PLA. The contents of the NR-ad-PCL were varied from 5, 10, 15 and 20 wt%. From thermal results, the incorporation of the NR-ad-PCL decreased the glass transition temperature and slightly increased degree of crystallinity of PLA. Mechanical properties of the PLA/NR-ad-PCL blends were investigated by dynamic mechanical analyser, pendulum impact tester and universal testing machine for tension and flexural properties. The increasing NR-ad-PCL contents led to decreasing Young’s and storage moduli but increasing loss modulus. Impact strength and elongation at break of the PLA/NR-ad-PCL blends increased with increasing NR-ad-PCL content up to 15 wt% where the maximum impact strength was about three times higher than that of pure PLA and the elongation at break increased to 79%.     

Chemically Functionalized Plant Fibers and Carbon Nanotubes for High Compatibility and Reinforcement in Polylactic Acid (PLA) Composite

In this study, surface modification is used to improve the compatibility of Kenaf fibers (KFs) and multi-walled carbon nanotubes (MWCNTs) in a polylactic acid (PLA) matrix, as well as to enhance the mechanical properties. Through the use of a silane coupling agent, the KF is grafted with functional groups to generate a chemical bond with the PLA; the modified KF shows high compatibility in the PLA matrix. Compared to the bare PLA, the optimal KF/MWCNT/PLA composite (PC1F30-OX) shows increases of 58% in tensile strength, and 113% in impact strength. A small addition of MWCNTs (1 wt%) dramatically improves the antistatic ability by lowering the surface resistance to 3.47 GΩ. With the addition of hydrophilic KF into the PLA, the composite becomes much more environmentally friendly, and the biodegradation rate can be controlled by the amount of KF added. The addition of hydrophilic KF allowed the composite to accommodate more enzyme to hasten the biodegradation; almost complete decomposition occurred after 11 weeks.     

Water-Soluble Pressure-Sensitive Adhesives Containing Carboxymethyl Starch with Improved Adhesion to Paper

Water-soluble pressure-sensitive adhesives (PSA) based on acrylic acid and carboxymethyl starch (CMS) have been prepared. The tack and peel adhesion to various paper types (newsprint, hygienic, packing, fax and art paper) as well as dynamic shear adhesion at higher temperatures (70–240?°C) have been tested with the aim of applying such PSA in a form of double-sided splicing tapes for paper industry. For all paper types tested tack and peel adhesion values increased with CMS content (0.1–10 wt% in PSA). The highest tack and peel adhesion values (for the system containing 10 wt% CMS) were noted for fax paper ca. 19.5 N/2.5 cm and 18.3 N/2.5 cm, respectively and the lowest ones for art paper: 14.7 N/2.5 cm and 13.5 N/2.5 cm, respectively. Obtained PSA were completely soluble in water, and the time of water-solubility depended on CMS content, as well as pH value, however it did not exceed 5 min.     

Characterization of Urea Encapsulated by Biodegradable Starch-PVA-Glycerol

The influence of the blending ratio of biodegradable starch/polyvinyl alcohol (PVA)/glycerol in encapsulating urea has been investigated. It is found that water absorption capacity increased approximately 135 % as the amounts of starch, PVA and glycerol in the composite film increase. Therefore, the swell ability of the composite film is increased and the urea is released from the composite film in the wet environment. The FTIR shows that the urea had been encapsulated successfully in the composite films. Moreover, the soil burial biodegradation results indicated that the biodegradability of the starch/PVA/glycerol/urea composite film strongly depended on the PVA proportion in the composite film matrix. The DSC results show that the higher the amount of PVA in the composite film, the less change of the melting enthalpy value. The crystalline region of PVA remains after biodegradation.     

Environmental Degradation of Biodegradable Polyesters: 3. Effects of Alkali Treatment on Biodegradation of Poly(ε-Caprolactone) and Poly[(R)-3-Hydroxybutyrate) Films in Controled Soil

The poly(-caprolactone) (PCL) and poly[(R)-3-hydroxybutyrate] (R-PHB) films with a hydrophilic surface were prepared by the alkali treatment of their as-cast films in NaOH solutions of different concentrations. The alkali-treated PCL and R-PHB films, as well as the as-cast PCL and R-PHB films, were biodegraded in soil controlled at 25°C and the effects of alkali treatment or surface hydrophilicities on their biodegradation were investigated by the use of gravimetry, gel permeation chromatography (GPC), scanning electron microscopy (SEM), and polarization optical microscopy. It became evident that the alkali treatment enhanced the hydrophilicities and biodegradabilities of the PCL and R-PHB films in soil. The biodegradabilities of the as-cast aliphatic polyester films in controlled soil decreased in the following order: PCL > R-PHB > PLLA, in agreement with that in controlled static seawater.     

Fabrication and Characterization of Biodegradable Composite Films Made of Using Poly(caprolactone) Reinforced with Chitosan

Chitosan was dissolved in 2?% aqueous acetic acid solution and the films were prepared by solution casting. Values of tensile strength (TS), tensile modulus (TM), elongation at break (Eb?%) and water vapor permeability (WVP) of the chitosan films were found to be 30?MPa, 450?MPa, 8?% and 4.7?g?mm/m²?day?kPa, respectively. Poly(caprolactone) (PCL) films were prepared from its granules by compression molding and the values of TS, TM, Eb and WVP were 14?MPa, 220?MPa, 70?% and 1.54?g?mm/m²?day?kPa, respectively. PCL was reinforced with chitosan films, and composite films were prepared by compression molding. Amount of chitosan in the composite films varied from 10 to 50?% (w/w). It was found that with the incorporation of chitosan films in PCL, both the values of TS and TM of composite films increased significantly. The highest mechanical properties were found at 50?% (w/w) of chitosan content. The Oxygen transmission rate (OTR) of composite film was found to decrease significantly than PCL films. Thermal properties of the composite were also improved as compared to PCL. The water uptake test of the composite also showed promising results with a good stability of composite films. The interface of the composite was investigated by scanning electron microscopy and showed good interfacial adhesion between PCL and chitosan films.     

Development of a Safe Solid-State Microorganism/Biodegradable Polymer Composite for Decomposition of Formaldehyde

A very safe and environmentally friendly solid-state material for bioremediation was prepared using a combination of Aspergillus oryzae and poly(ε-caprolactone) (PCL), a porous biodegradable polymer. The novel material was capable of decomposing 200 ppm formaldehyde solutions to 0 ppm within 7 days. Degradation ability was prolonged by addition of yeast extract-peptone-dextrose medium into the composite; 200 ppm formaldehyde was decomposed to 0 ppm over eight additional decomposition cycles and 100 days. A unique mechanism is proposed where, during PCL degradation, the solid-state composite provides nutrients to A. oryzae.