浅析地表水中挥发酚测定的注意点

在测定水中挥发酚时，影响分析结果的因素很多，如测定方法的选择、样品的蒸馏，4-氨基安替比林（以下简称4-APP）的处理等，当操作不当时，均会给分析结果带来影响，因此针对性地提出了解决的办法。     

活性污泥系统优化设计对不确定性参数的灵敏度研究

在活性污泥系统优化设计模型参数不确定性分析的基础上,考察了进水负荷、生物动力学参数、曝气设备性能参数和二沉池浓缩常数变化对优化设计的影响。灵敏度分析结果表明,对优化设计影响较大的参数为：进水水量水质、与氧转移效率相关的校正参数以及二沉池的浓缩常数等。研究结果对于低灵敏度系统的设计,提高优化设计结果的工程实用性具有重要的意义。     

油田常用化学品对含油废水处理效果的影响

通过对江汉油田采油废水水质分析以及混凝实验研究,分析采油作业返排液中主要化学组分对含油废水混凝处理效果的影响,探讨了混凝剂、常用油田化学品与浊度及油含量去除率的关系,初步分析了它们的作用机理。研究表明,在钻井液中,单宁、磺化酚醛树脂(SMP)等对含油废水处理的影响很大,在压裂液中瓜胶、重铬酸钾等的影响较大,酸化液中乙酸和柠檬酸等的影响较大,射孔液中盐酸等的影响较大。本研究的结果对于消除返排液对油田生产的不良影响,保证系列增储上产措施的实施及其有效性,避免环境污染,具有十分重要的参考价值。     

再生水用于都市绿地灌溉的研究进展

污水再利用具有节水和治污双重功能,用于绿地灌溉意义重大。综述了再生水灌溉对绿地土壤、植物、地下水的影响。着重介绍了国外的研究情况,分析了其试验结果及影响因素,表明虽然再生水中的一些有害成分会发生积累,但由于处理工艺、降雨等因素影响,对绿地生态系统影响不大,使用再生水灌溉绿地是切实可行的。     

电除尘器阳极板振打加速度分布规律与仿真设计

应用有限元分析软件LS-DYNA对影响电除尘器阳极板振打效果的锤头质量、锤臂长、悬挂方式及极板厚度等因素进行了数值仿真,分析了各因素对阳极板振打加速度分布的影响;利用分析结果对振打装置的结构进行了改进设计,结果表明可以较好地满足工业除尘的要求。本研究提出的电除尘器阳极板振打仿真方法为电除尘器振打装置的参数设计提供了一条新的途径。     

酸性法测定废水中高锰酸盐指数的体会

高锰酸盐指数（CODMn）是一个相对的条件性指标,其测定结果与样品溶液的酸度、高锰酸钾溶液的浓度、加热形式和温度、加热时间等条件有关。同时测定时必须要严格遵守操作规程,才能使结果具有可比性。文中通过对酸性高锰酸钾氧化法原理和过程的分析,并结合多年的实践经验,总结出在实际监测中,影响CODMn测定的几个因素,并针对各种影响因素提出了注意事项。     

AERMOD与EIAA大气预测模型在环境影响评价中的应用比较

大气环境影响预测是环境影响评价的一项重要内容,为准确评价项目实施后对周围大气环境的影响,需采用合适的大气预测模型.从大气预测模型系统组成原理、应用范围、应用过程、预测结果等方面对AERMOD和EIAA大气预测模型进行比较,分析两种模型在大气环境影响预测中的优缺点.     

土壤环境下污染物运移问题的数值模拟研究

在土壤环境中,物质传输机制显著影响着污染物的运移,分析污染物运移问题的数值解,可以掌握污染物在土壤中传输的时空规律,具有重要的理论意义和实际意义。以对流扩散传输理论为依据,建立了土壤环境下污染物运移的数学模型,然后基于COMSOL对几种特定初始及边界条件下的对流扩散问题进行数值模拟,计算了稳定连续、指数变化和瞬时释放3种典型污染源排放模型,并对比了模型中的扩散、对流、吸附降解等参数对计算结果的影响,最后对污染物浓度分布的计算结果进行了相关分析和讨论。     

烟气和粉尘性质对除尘效率影响的仿真研究

应用欧拉-拉格朗日多相流模型对影响电除尘器内部气流分布的烟气含尘浓度、烟气湿度、粉尘粒径及真密度等因素进行了数值仿真。分析了烟气和粉尘性质对除尘效率的影响。由于在仿真过程中考虑了烟气特性和粉尘性质等因素,不仅可获得各因素对气流分布均匀性的影响,而且仿真结果更能反映电除尘器气流分布的实际情况。提出的烟气和粉尘性质仿真方法可以为电除尘器除尘效率分析提供新的途径。     

玄武湖入湖口的悬浮颗粒物沉降调查研究

通过对玄武湖的外围入湖口及湖心的悬浮颗粒物的组成、悬浮颗粒物沉降量及沉降速率的对比实验,阐述了外源水、面源水的污染物对湖水水质的影响,并从面源、点源、水体自净能力及补给水等,促使湖水水质变化的途径入手,依据各项监测结果及对数据的分析,找出了玄武湖多次发生水污染的原因是多方面、多途径的影响结果。从监测分析发现,入湖口悬浮颗粒物沉降量高于湖心点,说明玄武湖水污染主要是受外源影响。另外还发现,入湖污水经水生植物阻滞、吸附和吸收后,其悬浮颗粒物的沉积速率和沉降量明显增大,据此认为,控制外源性污染、补充清洁水及在入湖口周围广种水生植物,是减缓湖水水质恶化,促使水质改良的有效途径。     

Bioindication of volatile elements emission by the Puyehue-Cordón Caulle (North Patagonia) volcanic event in 2011

The emission of volatile pollutants from the volcanic eruption of the Puyehue-Cordón Caulle complex (North Patagonia Andean Range) that started in June 4th, 2011, was investigated by bioindication means with the epyphytic fruticose lichen Usnea sp. The elemental composition of pooled samples made up with 10 lichen thalli were analysed by Instrumental Neutron Activation Analysis. Eleven sampling sites were selected within the impacted region at different distance from the volcanic source. Five sites were selected as they were already sampled in a previous study prior to the eruption. Two other new sampling sites were selected from outside the impacted zone to provide non-impacted baseline sites.The elements associated with the lichen incorporation of particulate matter (PM) of geological origin were identified by linear correlation with a geochemical tracer (Sm concentrations). The elements associated with PM uptake were Ce, Eu, Fe, Hf, La, Lu, Na, Nd, Sb, Sc, Se, Ta, Tb, Th, U, and Yb. Arsenic and Cs concentrations showed contributions exceeding the PM fraction in sites near the volcanic centre, also higher than the baseline concentrations, which could be associated with permanent emissions from the geothermal system of the Puyehue-Cordón Caulle complex. The lichen concentrations of Ba, Ca, Co, Hg, K, Rb, Sr, and Zn were not associated with the PM, not showing higher concentrations in the sites nearby the volcanic source or respect to the baseline values either. Therefore, there is no indication of the emission of volatile forms of these elements in the lichen records. The lichen records only identified Br volatile emissions associated with the Puyehue-Cordón Caulle complex eruption in 2011.     

Environmental impacts of coastal aquaculture in eastern mediterranean bays the case of astakos gulf,Greece

GOAL, SCOPE AND BACKGROUND: Over the last decade Greece has become a leading country in the EU as concerns the cage farming of seabream and seabass. A strong debate has risen, however, about the environmental impacts of aquacultures in the coastal areas. The present paper deals with this problem and it is based on measurements of physico-chemical parameters in the water column, particulate matter and sediments in the area of Astakos Gulf, a coastal embayment in western Greece where three big fish farms are currently operating. METHODS: Water samples were collected by using Hydro-Bios sampling bottles, whereas a prototype sediment trap was installed under a fish cage for the collection of particulate matter. Temperature, dissolved oxygen, pH and salinity were measured in situ using portable equipment. Nutrients were determined by standard spectrophotometric methods. Trace metals were determined by Atomic Absorption Spectrometry. Dissolved organic carbon was determined by a Shimadzu 5000A carbon analyzer, whereas organic carbon in sediments was determined titrimetrically. RESULTS AND DISCUSSION: No clear eutrophication incidents have been identified, although the water column near the fish farms was enriched in nutrients and organic carbon. A sludge 'blanket' covers considerable parts of the seabed and is enriched in colloidal organic carbon and trace metals (Cd, Cu, Fe and Zn) that come from unused fish food. The biodegradation of this sludge leads to the development of anoxic conditions followed by the formation of undesirable gases, precipitation or remobilization of metals and the extinction of benthic fauna. CONCLUSION: The operation of fish farms at the coastal area of Astakos Gulf, and probably in similar Mediterranean gulfs, affects the marine environment, particularly in the vicinity of the cages. The most significant influence concerns the near-bottom water layer. The environmental impacts depend on the amount of food given to fishes, the mode of feeding, the fish density in cages, the annual production and the years of unit operation. The hydrology and the geomorphology of the area are also critical factors for its environmental quality. RECOMMENDATION AND OUTLOOK: The success of the fish-farming sector in the Mediterranean is accompanied by environmental and, in some extents, by social and marketing problems. These problems, derived from the rapid development of fish farming, can be solved only through an integrated management, using methods such as environmental impact assessment, risk assessment, economic evaluation, vulnerability assessments, resource accounting, cost-benefit analysis and outcome-based monitoring.     

Herbicide Leaching on a Recharge Area of the Guarany Aquifer in Brazil

Abstract

The region of Ribeirão Preto City, located in Southeast of Brazil, São Paulo State, is an important sugarcane, soybean, and corn producing area with a high level of pesticides utilization. This region is also an important recharge area for groundwater supply of the Guarany aquifer. Since the past ten years atrazine, simazine, ametryn, tebuthiuron, diuron, 2,4-D, picloram, and hexazinone are the main herbicides used in this area. In order to study a possible leaching of some of these herbicides into the aquifer, surface, and groundwater samples were collected in a watershed during the years of 1996 to 2003, from different locations. To detect and quantify the herbicides a GC-MS (gas chromatograph/mass spectrometry) method was used. The response of the herbicides analyzed was linear over the concentration range of 0.02 to 2.0 μg/L. Analysis of groundwater revealed that the herbicides tebuthiuron, diuron, atrazine, simazine, and ametryn were not present in the samples. In the surface water collected in 1997, ametryn was present in two out of nine locations with concentrations ranging from 0.17 and 0.23 μg/L, which is above the allowable 0.1 μg/L according to the European safety level. The leaching potential of tebuthiuron, diuron, atrazine, simazine, 2,4-D, picloram, and hexazinone has been evaluated using CMLS-94, “Chemical Movement in Layered Soil,” as simulation model. No leaching into the depth of the water table at 40 m was found.     

Mathematical modeling of biofiltration in activated pine-bark charge of a biofilter

Aim, Scope and Background Human economic activities cause emissions of various pollutants of an organic nature: butanol, butyl acetate, methanol, formaldehyde, phenol, benzene, toluene, xylene, etc. These compounds are emitted to atmosphere by various enterprises of food, chemistry, wood processing industries, from transportation means, agricultural enterprises, etc. Therefore, when purifying air from these pollutants, it is necessary to apply efficient and inexpensive air purification methods. In this dimension, the biological air purification is chosen from all possible air cleaning methods. An experimental biofilter with the activated charge of pine bark was developed at the Department of Environment Protection of the Vilnius Gediminas Technical University. In the course of the experimental investigation, it was determined that this air purification method is efficient. Filter efficiency, when purifying air of volatile organic compounds (butanol, butyl acetate and xylene), to a great extent, depending on the nature and concentrations (up to 100 mg/m3) of pollutants injected, might go up to 70-98%. The mathematical model of the biofilter was developed based on the research results and fully taking into consideration physical, chemical, and biological processes going on during its operations. Main Features The aim of this article is to determine biodegradation constant , absorption capacity , and half empiric expressions of filter efficiency. Knowing this, it is possible to find out the dependence of the filter efficiency on the operational parameters of the filter (i.e. on the concentrations and the height of biocharge of the initial pollutants (butanol, butyl acetate, xylene) fed through it). Conclusions With the help of mathematical modeling, the biodegradation constants and absorption capability of volatile organic compounds (butanol, butyl acetate, and xylene) fed into the biofilter charged with the activated pine bark and used for the cleaning of volatile organic compounds, as well as the efficiency of the biofilter in half empiric expression, have been established. It has been discovered that the constant of pollutant biodegradation is a value inverse to the time during which the amount of pollutants in the filter becomes times higher. It is rather complicated to carry out theoretical calculation of the biodegradation constant at a molecular level, therefore this constant has been established based on the results obtained in the course of research. The equations describing pollutant dynamics in the filter charge and the air cleaning processes going on in it have been derived from diffusion equations in a mobile medium. The modeling helped to find out the absorption capacity of the examined pollutants, which by its numeric value is equal to the volume unit of the absorbed gas amount. The latter factor, the same as the biodegradation constant, was determined basing on the experimental results. Mathematical modeling brought a range of formulas expressing dependences of each pollutant's efficiency on its initial concentrations and filter charge height. Recommendation /Outlook. Based on the experimental data, a mathematical model has been developed which will allow the measuring of the filter efficiency not only with regard to the absorption and biodegradation of the pollutants under examination, but also with regard to other pollutants and their compounds, etc., having an impact on the filter performance. The results of the mathematical modeling have revealed that the modeling of processes going on in the filter is much simpler than isthe performance of long and costly experiments. The developed mathematical model makes it possible to measure the filter efficiency at the present moment.     

Identification of priority pharmaceuticals in the water environment of China

In recent years, increasing attention has been paid to the trace-level contamination of pharmaceuticals in the water environment all over the world. Considering a large number of pharmaceuticals used, it is crucial to establish a priority list of pharmaceuticals that should be monitored and/or treated first. In the present study, we developed a ranking system based on the pharmaceutical consumption, removal performance in the wastewater treatment plants (WWTPs) and potential ecological effects, and applied to the situation of China. 39 pharmaceuticals, which had available consumption data and also been reported previously in the WWTPs of China, were selected as candidate pharmaceuticals. Among them, seventeen pharmaceuticals were considered as priority pharmaceuticals, out of which, erythromycin, diclofenac acid and ibuprofen, had the high priority. Compared with other literatures, we found that some pharmaceuticals given concerns to globally should also be included in the priority list in China; while some pharmaceuticals, not mentioned in other literatures, such as cefalexin, ketoconazole, should be also given prior consideration in China. Among all the therapeutic classes, antibiotics, which were grossly abused in China, contributed the most to the priority pharmaceuticals. However, priority antibiotics accounted for only 32% of candidate antibiotics, while 71% and 100% of the candidate anti-inflammatory and antilipidemic respectively were identified as the priority pharmaceuticals, indicating that antibiotics might be overanxiously considered in the previous studies on their behaviors in the WWTPs of China.     

Interactions of Physical, Chemical, and Biological Weather Calling for an Integrated Approach to Assessment, Forecasting, and Communication of Air Quality

This article reviews interactions and health impacts of physical, chemical, and biological weather. Interactions and synergistic effects between the three types of weather call for integrated assessment, forecasting, and communication of air quality. Today’s air quality legislation falls short of addressing air quality degradation by biological weather, despite increasing evidence for the feasibility of both mitigation and adaptation policy options. In comparison with the existing capabilities for physical and chemical weather, the monitoring of biological weather is lacking stable operational agreements and resources. Furthermore, integrated effects of physical, chemical, and biological weather suggest a critical review of air quality management practices. Additional research is required to improve the coupled modeling of physical, chemical, and biological weather as well as the assessment and communication of integrated air quality. Findings from several recent COST Actions underline the importance of an increased dialog between scientists from the fields of meteorology, air quality, aerobiology, health, and policy makers.     

The Effect of Grain Size and Element Concentration in Identifying Contaminant Sources

The distribution of metal contaminants between different size fractions of marine sediments is well known. However, the use of size normalization techniques may alter the ability or usefulness in identifying potential sources in complex environments. In a reassessment of metal data from the shelf area of Sydney, Australia, the mud and sand fractions were investigated separately by PCA and PLS methodologies. The analyses were able to produce clear distinctions between industrial/urban sources when based on a suite of metals rather than individual (single-element) concentrations. Signature analysis by PLS with copper, lead, zinc, manganese, chromium, cobalt, nickel, and cadmium demonstrated the dispersion of the fine-grained contaminated material to the south in the East Australian Current. However, due to the commonality between many of the metals, a subset of four metals was used to define the signature. This significantly improved separation, showing clear plumes extending ～30 km from the source rivers.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Transport and degradation of pesticides in a biopurification system under variable flux, part I: A microcosm study

The efficiency of a biopurification system, developed to treat pesticide contaminated water, is to a large extent determined by the chemical and hydraulic load. Insight into the behaviour of pesticides under different fluxes is necessary. The behaviour of metalaxyl, bentazone, linuron, isoproturon and metamitron was studied under three different fluxes with or without the presence of pesticide-primed soil in column experiments. Due to the time-dependent sorption process, retention of the pesticides with intermediate mobility was significantly influenced by the flux. The higher the flux, the slower pesticides will be sorbed, which resulted in a lower retention. Degradation of the intermediate mobile pesticides was also submissive to variations in flux. An increase in flux, led to a decrease in retention, which in turn decreased the opportunity time for biodegradation. Finally, the presence of pesticide-primed soil was only beneficial for the degradation of metalaxyl.     

Heavy metal pollution in China: Origin,pattern and control

GOAL, SCOPE AND BACKGROUND: Heavy metal is among one of the pollutants, which cause severe threats to humans and the environment in China. The aim of the present review is to make information on the source of heavy metal pollution, distribution of heavy metals in the environment, and measures of pollution control accessible internationally, which are mostly published in Chinese. METHODS: Information from scientific journals, university journals and governmental releases are compiled focusing mainly on Cd, Cu, Pb and Zn. Partly Al, As, Cr, Fe, Hg, Mn and Ni a included also in part as well. RESULTS AND DISCUSSION: In soil, the average contents of Cd, Cu, Pb and Zn are 0.097, 22.6, 26.0 and 74.2 mg/kg, respectively. In the water of the Yangtze River Basin, the concentrations of Cd, Cu, Pb and Zn are 0.080, 7.91, 15.7 and 18.7 microg/L, respectively. In reference to human activities, the heavy metal pollution comes from three sources: industrial emission, wastewater and solid waste. The environment such as soil, water and air were polluted by heavy metals in some cases. The contents of Cd, Cu, Pb and Zn even reach 3.16, 99.3, 84.1 and 147 mg/kg, respectively, in the soils of a wastewater irrigation zone. These contaminants pollute drinking water and food, and threaten human health. Some diseases resulting from pollution of geological and environmental origin, were observed with long-term and non-reversible effects. CONCLUSIONS: In China, the geological background level of heavy metal is low, but with the activity of humans, soil, water, air, and plants are polluted by heavy metals in some cases and even affect human health through the food chain. RECOMMENDATIONS AND OUTLOOK: To remediate and improve environmental quality is a long strategy for the polluted area to keep humans and animals healthy. Phytoremediation would be an effective technique to remediate the heavy metal pollutions.