The predictive accuracy of published solid waste generation factors

The accuracy of predictions of quantities of solid waste based upon waste generation factors reported in the literature was tested. Estimates of residential, industrial, and commercial solid waste quantities were computed for Brown County. Wisconsin U.S.A. and compared to actual waste quantities received. Predictions were within 20% for residential wastes and for some predictions of commercial wastes but far from the mark for industrial and construction-demolition wastes.     

Characteristics of MSW and heat energy recovery between residential and commercial areas in Seoul

This paper analyzes the amount and characteristics of municipal solid waste (MSW) according to the inhabitant density of population and the business concentration in 25 districts in Seoul. Further, the heat energy recovery and avoided CO₂ emissions of four incineration plants located in residential and commercial areas in Seoul are examined. The amount of residential waste per capita tended to increase as the density of inhabitants decreased. The amount of commercial waste per capita tended to increase as the business concentration increased. The examination of the heat energy recovery characteristics indicated that the four incineration plants produced heat energy that depended on residential or commercial areas based on population and business. The most important result regarding avoided CO₂ emissions was that commercial areas with many office-type businesses had the most effective CO₂ emission savings by combusting 1 kg of waste. Assuming the full-scale operation of the four incineration plants, the amount of saved CO₂ emissions per year was 444 Gg CO₂ and 57,006 households in Seoul can be provided with heat energy equivalent to 542,711 Nm³ of LNG.     

Curbside Recycling In The U.S.A.: Convenience And Mandatory Participation

This research examines the relationship between the success of a residential curbside recycling program (RCRP), measured as material recovery rate (MRR), and two program factors: (1) whether or not participation is mandated; and (2) convenience, measured by container provision, collection frequency and collection day relative to municipal solid waste collection day. Residential curbside recycling programs, with correct strategies and program design, can be an important part of solid waste management plans world-wide. While residential curbside recycling programs are growing in popularity, many basic design questions lie unanswered and successful program strategies are not always obvious. Data from 357 residential curbside recycling programs in the United States are used to test the hypotheses. Mandatory participation residential curbside recycling programs are seen to collect more material than voluntary participation residential curbside recycling programs. Container provision appears effective for voluntary, but not mandatory, residential curbside recycling programs. Increasing collection frequency appears to have a small positive effect on residential curbside recycling program success, while collection day has little effect on material recovery rate.     

Report on hazardous household waste generation in Japan.

Surveys of over 2000 households in Japan were conducted to investigate the characteristics of hazardous household waste (HHW) generation. In Japan, about 2.5 to 4.3 kg of HHW are produced per tonne of the residential waste stream. The percentage of used batteries in HHW was over 50%. Every household using spray (aerosol) cans had more than seven cans on average. The generation of HHW, in terms of both quantities and type of waste produced, appeared to vary with dwelling type. Detached dwelling residents tended to store HHW such as used batteries, whereas apartment residents tended not to store waste. The amounts of discarded HHW were larger at the end of the year in comparison with other months. The data accumulated were used to estimate the quantities of HHW disposed off annually, and the quantities and type of waste that might be received by a typical depot collection programme in Japan.     

Mathematical modeling to predict residential solid waste generation

One of the challenges faced by waste management authorities is determining the amount of waste generated by households in order to establish waste management systems, as well as trying to charge rates compatible with the principle applied worldwide, and design a fair payment system for households according to the amount of residential solid waste (RSW) they generate. The goal of this research work was to establish mathematical models that correlate the generation of RSW per capita to the following variables: education, income per household, and number of residents. This work was based on data from a study on generation, quantification and composition of residential waste in a Mexican city in three stages. In order to define prediction models, five variables were identified and included in the model. For each waste sampling stage a different mathematical model was developed, in order to find the model that showed the best linear relation to predict residential solid waste generation. Later on, models to explore the combination of included variables and select those which showed a higher R(2) were established. The tests applied were normality, multicolinearity and heteroskedasticity. Another model, formulated with four variables, was generated and the Durban-Watson test was applied to it. Finally, a general mathematical model is proposed to predict residential waste generation, which accounts for 51% of the total.     

Thermal cracking of oils from waste plastics

Thermal cracking of decomposed waste plastic oil produces a good yield of olefins. The solvent extraction of such waste plastic oil seems to be efficient for increasing gas yields and recycling monomers. To assess the potential of monomer recovery from municipal waste plastics, the oils were cracked using a laboratory-scale quartz-tube reactor. The waste plastic oils were provided by two commercial plants of the Sapporo Plastic Recycle Co. and the Dohoh Recycle Center Co. in Japan. A model waste plastic oil made in a laboratory was also examined. Yields of ethene, propene, and other products were measured at different temperatures. Two-step pyrolysis reduces coking compared with the direct thermal degradation of plastics. The raffinates from waste plastic oils extracted by sulfolane were also cracked. The primary products were almost the same as those from nontreated oils. The maximum total gas yield was 78wt%–85wt% at 750°C, an increase of about 20wt% compared with that of nonextracted oil. Solvent extraction removes stable aromatic hydrocarbons such as styrene, which is more coked than cracked.     

The Origins Of Municipal Solid Waste: II. Policy Options For Plastics Waste Management

Plastic items in some portions of municipal solid waste (MSW), particularly from households and restaurants, have long been viewed as a disposal problem and a symbol of a "throwaway society". There is no question that the amount of plastics in solid waste is growing. However, this observation alone should not cause an hysteria of public policies for the separate management of the plastics or any other portion of the waste. The amount of plastics, and the contribution of the items discarded, must be viewed holistically in setting a solid waste management policy. This paper questions the basis for some U.S. plastics waste policy proposals by reviewing recent U.S. data on the effect of plastics on waste reduction, and the fate of discarded plastics products. Some alternative future policy directions are also discussed.     

Infectious waste management in Japan: assessment of current trends in waste measurement and reporting in general and psychiatric hospitals

Infectious waste (IW) may include waste contaminated with blood and other bodily fluids, cultures of infectious agents from laboratory work, or waste from patients with infections. Accurate and standardized measurement is an important aspect of waste management. In Japan, data on infectious waste generated by hospitals are limited. Therefore, we aimed to identify the current status of infectious waste management and disposal in hospitals. To this end, data on the amount of IW generated and IW disposal costs from 54 public hospitals—25 general hospitals and 29 psychiatric hospitals—between April 2015 and March 2016 were analyzed. The results revealed the absence of a standardized unit of IW measurement, with 33 hospitals reporting IW in kilograms and 21 hospitals reporting it in liters. As expected, the amount of IW generated at psychiatric hospitals was significantly lower than that generated at general hospitals. The amount of IW produced correlated positively with the number of in-patients. Disposal costs varied not only by hospital type and prefecture but also across hospitals of the same type within the same prefecture. A system that consolidates IW data management using standardized units is necessary.

     

Estimation of regional building-related C&D debris generation and composition: case study for Florida, US

Methodology for the accounting, generation, and composition of building-related construction and demolition (C&D) at a regional level was explored. Six specific categories of debris were examined: residential construction, nonresidential construction, residential demolition, nonresidential demolition, residential renovation, and nonresidential renovation. Debris produced from each activity was calculated as the product of the total area of activity and waste generated per unit area of activity. Similarly, composition was estimated as the product of the total area of activity and the amount of each waste component generated per unit area. The area of activity was calculated using statistical data, and individual site studies were used to assess the average amount of waste generated per unit area. The application of the methodology was illustrated using Florida, US approximately 3,750,000 metric tons of building-related C&D debris were estimated as generated in Florida in 2000. Of that amount, concrete represented 56%, wood 13%, drywall 11%, miscellaneous debris 8%, asphalt roofing materials 7%, metal 3%, cardboard 1%, and plastic 1%. This model differs from others because it accommodates regional construction styles and available data. The resulting generation amount per capita is less than the US estimate - attributable to the high construction, low demolition activity seen in Florida.     

An alternative method for the treatment of waste produced at a dye and a metal-plating industry using natural and/or waste materials.

The aim of this study was to develop cost-effective, appropriate solidification technologies for treating hazardous industrial wastes that are currently disposed of in ways that may threaten the quality of local groundwater. One major objective was to use materials other than cement, and preferably materials that are themselves wastes, as the solidification additives, namely using wastes to treat wastes or locally available natural material. This research examines the cement-based and lime-based stabilization/solidification (S/S) techniques applied for waste generated at a metal-plating industry and a dye industry. For the lime-based S/S process the following binder mixtures were used: cement kiln dust/ lime, bentonite/lime and gypsum/lime. For the cement-based S/S process three binder mixtures were used: cement kiln dust/cement, bentonite/cement and gypsum/cement. The leachability of the wastes was evaluated using the toxicity characteristic leaching procedure. The applicability and optimum weight ratio of the binder mixtures were estimated using the unconfined compressive strength test. The optimum ratio mixtures were mixed with waste samples in different ratios and cured for 28 days in order to find the S/S products with the highest strength and lowest leachability at the same time. The results of this work showed that the cement-and lime-based S/S process, using cement kiln dust and bentonite as additives can be effectively used in order to treat industrial waste.     

Monthly variations in solid waste generation

The monthly quantities of residential, commercial, industrial and other wastes generated between 1985–1989 in Brown County, Wisconsin, U.S.A. are analysed. For each month and each waste type, the quantity of waste generated is compared with the monthly average and the difference is computed as a percentage. The means and standard deviations of these percentage differences are computed for each month using the five values computed for each of the five years. The generation patterns for residential, commercial, construction and demolition wastes, and discarded tires show lower than average generation in winter months and higher than average in summer months, with the residential and commercial components being the most predictable. Ash has the opposite pattern with the most produced in winter months. General industrial wastes are produced at an almost constant rate throughout the year, typically varying by less than 10% from the monthly average. Sludge appears to be the least predictable component of the waste stream.     

Substance flow analysis of brominated flame retardants and related compounds in waste TV sets in Japan

We conducted time-series substance flow analysis of two types of brominated flame retardants (BFRs)--polybrominated diphenyl ethers (PBDEs) and tetrabromobisphenol A (TBBPA)--and two types of related compounds--Sb (used with BFRs for flame inhibition) and polybrominated dibenzo dioxins and furans (PBDDs/DFs: unintended byproducts)--in five size categories of waste TV sets in Japan. Two scenarios were created with BFR substitutions and compared to a "business as usual" scenario in order to obtain basic information for strategic product management. The results showed that the use of DecaBDE in rear and front covers of TV sets began in fiscal 1987-1990 and 1993-1996, respectively, and that TBBPA was used to some extent as a substitute for DecaBDE in the 90s. The amount of waste Br in the plastic covers is predicted to increase until at least fiscal 2020 due to the increasing size of TV sets. Although substitution of BFRs with non-BFRs in Japan by 2006 will reduce waste Br, the amount in waste TV sets will not peak until fiscal 2009. The results will help inform decisions in Japan regarding the recovery and disposal of waste TV sets. The methods used would benefit waste managers faced with similar issues in other countries.     

Use of flue gas desulphurisation (FGD) waste and rejected fly ash in waste stabilization/solidification systems

Stabilization/solidification (S/S) processes have been used as the final treatment step for hazardous wastes prior to land disposal. Fly ash is a by-product of coal-fired power generation; a significant proportion of this material is low-grade, reject material (rFA) that is unsuitable as a cement replacement due to its high carbon content and large particle size (>45 microm). Flue gas desulphurization (FGD) sludge is a by-product from the air pollution control systems used in coal-fired power plants. The objective of this work was to investigate the performance of S/S waste binder systems containing these two waste materials (rFA and FGD). Strength tests show that cement-based waste forms with rFA and FGD replacement were suitable for disposal in landfills. The addition of an appropriate quantity of Ca(OH)2 and FGD reduces the deleterious effect of heavy metals on strength development. Results of TCLP testing and the progressive TCLP test show that cement-rFA-Ca(OH)2 systems with a range of FGD additions can form an effective S/S binder. The Leachability Index indicates that cement-based waste forms with rFA replacement were effective in reducing the mobility of heavy metals.     

Non-hazardous waste generation characteristics and recycling practices in Saskatchewan and Manitoba,Canada

The paper presents the results on the analysis of non-hazardous waste generation characteristics and recycling practices in Saskatchewan (SK) and Manitoba (MB) using the biennial waste reports published by Statistic Canada. The objectives are to examine the waste generation rates from both residential and non-residential sources from 1998 to 2010, and to evaluate the effectiveness of their recycling programs and regulations. In spite of the many similarities between the provinces, MB on average generated 17.5 % more residential waste than SK, and about 15 % less non-residential waste than SK during the study period. It appears that MB waste generation characteristics were very different from SK and the rest of Canada. The amount of MSW generation in MB was, to a certain degree, independent from the economic factors. Assuming status quos conditions, the linear models predicted that the per capita MSW generations in MB would be about 33 % lower than SK in 2020. Data from this study suggest that (1) curbside recycling programs and (2) pay-as-you-throw collection systems may be important factors for increasing diversion rate in SK. It is also found that the non-residential waste generation in Canada was substantially larger than the residential waste generation during the 13-year period.     

Pneumatic vs. door-to-door waste collection systems in existing urban areas: a comparison of economic performance

Pneumatic waste collection systems are becoming increasingly popular in new urban residential areas, and an attractive alternative to conventional vehicle-operated municipal solid waste (MSW) collection also in ready-built urban areas. How well pneumatic systems perform in ready-built areas is, however, an unexplored topic. In this paper, we analyze how a hypothetical stationary pneumatic waste collection system compares economically to a traditional vehicle-operated door-to-door collection system in an existing, densely populated urban area. Both pneumatic and door-to-door collection systems face disadvantages in such areas. While buildings and fixed city infrastructure increase the installation costs of a pneumatic system in existing residential areas, the limited space for waste transportation vehicles and containers cause problems for vehicle-operated waste collection systems. The method used for analyzing the cost effects of the compared waste collection systems in our case study takes into account also monetized environmental effects of both waste collection systems. As a result, we find that the door-to-door collection system is economically almost six times more superior. The dominant cost factor in the analysis is the large investment cost of the pneumatic system. The economic value of land is an important variable, as it is able to reverse the results, if the value of land saved with a pneumatic system is sufficiently high.     

The origins of municipal solid waste: The relations between residues from packaging materials and food

Data for the composition of municipal solid waste (MSW) from around the world are used to further examine a previously reported statistical correlation between the fraction of food residues and the fractions of paper and board, metal, glass and plastics residues in MSW. For data from many locations, these correlations are statistically significant; multiple linear regressions are computed. The fraction of food waste decreases as the fractions of waste from paper and board, metals and glass increase.The situation in the U.S.A. is examined further for just packaging waste. Similar correlations are established for the fraction of food residues and the fractions of paper and board and plastics packaging residues for predicted compositions for 1980 to 2000. Similar correlations for the U.K. are not statistically significant. Some reasons for this are postulated.The results of the statistical analyses predict that a strategy for decreasing the fraction of food waste in MSW is to increase the use of food packaging by some amount, especially plastics and metals, contrary to conventional wisdom.     

Raw material potential of recyclable materials for fiber composites: a review study

The aim of this study is to investigate waste streams as a source of recyclable raw material for fiber composite production. Globally, vast volumes of waste are produced daily that are not recycled effectively. In this work, three different raw material sources are examined; industrial, construction and municipal solid waste streams. All three sources produce wastes that are currently underutilized. Usage areas for the waste material include use as a reinforcing fiber, as part of the plastic matrix or as a filler. The industrial sector produces more homogenous waste, while waste from municipalities is mixed. Irregular material flow, the varying condition of the waste and different pretreatments used pose difficulties for recycling. Furthermore, some materials are industry-specific and may be produced in only certain areas. Despite these difficulties, huge amount of potentially useful exploitable waste is available and using different waste streams as a part of wood-plastic composite production can reduce waste volumes disposed to landfill.     

Attitudes and behaviour towards waste management in the Dublin,Ireland region

The hypothesis of this research was that attitudes about the management of biodegradable municipal waste (BMW) are spatially variable, even within a city of modest (1.2 million) population. For a select number of representative electoral districts in the Dublin, Ireland region, residents were surveyed regarding attitudes towards waste management in general, and BMW management in particular. A total of 850 survey responses were collected. Door-to-door interviews produced 688 responses in the residential sector; these were supplemented by 162 responses to a web-based survey.The surveys revealed that the majority of households use local authority, rather than private, waste collection services (both are available). The majority of residents, regardless of the local authority in which they live, were satisfied with their waste management service. “Reducing the quantity of waste generated” was regarded the most important future issue for 28% of residential respondents. Statistical analyses of the survey responses showed that the local authority in which respondents resided significantly influenced most responses (including waste collection service used, waste service satisfaction and backyard composting activity). Many responses (including waste service satisfaction, waste management influences) were also significantly related to the respondents’ personal characteristics (e.g., education level, type of accommodation, age, etc.). These statistical results proved the hypothesis of the research and demonstrated that waste management initiatives designed for one area of the city (or, indeed, for uniform application to the city as a whole) could ignore the needs of other areas. The survey responses suggest that targeted intervention strategies would lead to improved diversion rates of BMW from landfill, a requirement of the Landfill Directive 1999/31/EC.     

Waste plastics recycling process using coke ovens

The Japan Iron and Steel Federation (JISF), as its voluntary energy-saving action plan, proposed a 10% energy reduction by 2010 with 1990 as the basis. Further, it has suggested an additional 1.5% energy saving by the use of waste plastics as a metallurgical raw material. The amount of processing of waste plastics which corresponds to this amount of energy conversion is about 1 million t scale during 1 year. Conventional known methods for recycle-processing of waste plastics include, for example, the method of injection into a blast furnace to use waste plastics as an iron-ore reducing agent instead of coal. On the other hand, the coking process is considered to be suitable as a waste plastic recycling facility because the process involves coal carbonization in a high-temperature and reducing atmosphere. Carbonization tests with mixed waste plastics were conducted with laboratory equipment and in actual coke ovens. As a result, it was confirmed that the waste plastics recycling process using coke ovens is feasible. Therefore, a waste plastics recycling process using coke ovens was started as a chemical recycling technology at Nippon Steel.     

Control of volatile organic compound emissions at a landfill site in New York: A community perspective

This paper presents a case study of a Long Island. New York, landfill where methane and VOC gases were migrating off-site. The municipally owned and operated Port Washington Landfill located adjacent to residential housing was opened in 1974 and was placed on the U.S. EPA Superfund (rehabilitation) list in 1982 because of odour complaints. Community concerns have focused on combustible gases, odour control, and exposure to trace contaminants. A comprehensive data base and corrective action program was initiated to determine: (1) the extent of off-site volatile organic compounds (VOC) migration; (2) measures to control migration and emissions; and (3) impacts on VOC concentrations under residential areas. Full data reports and monthly interpretations have been provided to the citizenry. Results to date indicate that start-up and operation of the extraction system have significantly reduced off-site VOC concentrations.