石油降解菌的筛选优化及其对油污土壤的修复特性

分别以牛肉膏蛋白胨-布氏哈斯培养基、蓝色凝胶培养基作为初筛和复筛培养基,从石油污染土壤中筛选出2株可产生微生物表面活性剂的石油烃降解菌。并将菌株投加到油污土壤中进行修复研究,考查了不同影响因素对修复效果的影响。研究结果表明,(1)2株菌对中度石油污染土壤有较好的修复效果,向油污土壤中直接投加菌株修复70 d时对石油烃的去除率为52%;(2)向油污土壤中投加降解菌并同时补充氮营养液,修复70 d时对土壤中总石油烃的去除率可达到75%;对土壤中正构烷烃的去除率为66%;(3)与土壤的含水率及土著菌的降解效果相比,向油污土壤中投加降解菌以及补充氮磷营养液是影响石油污染土壤修复效果的关键因素。     

降解菌ZQ5与紫茉莉对芘污染土壤的联合修复

在温室盆栽条件下,通过单独种植紫茉莉、单独接种多环芳烃(PAHs)模式化合物芘的专性降解菌ZQ5和两者的联合修复的3种处理,对芘污染土壤的修复效果进行了研究。结果表明,经90 d修复后,植物-微生物联合修复可将人工污染土壤中的芘降解81.1%,将石油污染土壤中的芘降解50.3%,其修复效率明显高于其他2种处理,是紫茉莉修复的1.98倍,是降解菌ZQ5修复的1.39倍。ZQ5的不同接菌量对于修复60 d后的降解率影响不大。外源生物修复条件下,10～20 cm土壤的修复效率要高于5 cm土壤;自然降解条件下,5 cm土层降解率略高于其他土层。     

用于石油污染土壤降解的高效降解菌的筛选及其降解条件优化

经过富集、分离优选出高效石油降解菌L-1,根据形态观察和生理生化特征初步鉴定为琼氏不动杆菌;采用单因素花盆实验模拟微生物原位修复并对其降解条件进行优化。结果表明,将高效石油降解菌应用于修复石油污染土壤,适宜接种量、表面活性剂浓度、CNP比、翻耕频率分别为15%、0.1%、100∶10∶1和1 d 1次;在该降解条件下修复28 d,可达到16.80%的石油降解率,远远高于土著微生物6.92%的降解率。     

固废拆解场污染土壤中多环芳烃降解菌的筛选鉴定与降解特性

以腐植酸(HA)溶液为吸附剂、从受多环芳烃污染的土壤中分离出来的降解菌制成为生物修复剂,以多环芳烃(PAHs)萘、菲、芘、荧蒽、苯并蒽、苯并芘为土壤污染物,对PAHs污染土壤进行修复实验。目的是筛选与分离吸附于HA的PAHs降解菌,研究HA与降解菌的协同效应对PAHs的降解效率的影响。用经过HA吸附的PAHs富集分离培养出1株高效降解菌株,命名为Tzyx3,鉴定其为解脂耶氏酵母菌(Yarrowia lipolytica)。15 d后,土壤中萘、菲、芘、荧蒽、苯并蒽、苯并芘的降解率分别为90.7%、91.0%、74.7%、86.9%、84.7%和74.7%,表明Tzyx3和HA在PAHs污染土壤中存在协作关系,Tzyx3能够直接利用HA对土壤中的多环芳烃进行降解。     

土壤石油烃污染的植物毒性及植物-微生物联合降解

通过盆栽实验研究了土壤石油烃污染对玉米和水稻根伸长的影响,并在土壤中接种经过筛选得到的石油烃降解菌,研究石油烃降解菌对石油烃毒性的影响以及对土壤中石油烃的降解。研究结果表明,石油烃浓度低于1 000 mg/kg时对玉米的根系生长有一定的刺激生长作用,随着石油烃浓度的增加,刺激根长生长的作用逐渐降低,研究结果表明,水稻根长受石油烃影响较小。通过对不同处理土壤中石油烃降解的研究结果表明,土壤中种植水稻对石油烃有一定的降解作用,但是不同处理下土壤中的石油烃降解率不同,其中水稻微生物联合处理下土壤中石油烃的降解速率最快,培养期内的降解效率达到53.3%。     

多环芳烃降解菌菌群构建及其适宜降解环境条件的确定

利用富集培养技术从某焦化厂土壤中筛选出来的菌种,根据3种不同的配伍方式构成3种不同的菌群。以苯并[a]芘、苯并[a]蒽、苯并[b]荧蒽、苯并[k]荧蒽和茚并[1,2,3-cd]芘5种多环芳烃为唯一碳源的无机盐培养基,不同菌群降解效率均达到60%以上。模拟多环芳烃污染的土壤环境,利用正交实验对菌群组合、菌量等因素不同水平探索降解的适宜条件。降解14 d的适宜条件为组合二:菌量20%、温度30℃、土壤含水率15%、营养盐质量比(m(C)∶m(N)∶m(P))为120∶10∶1、表面活性剂500 mg·kg-1、Fenton试剂和植物油2.5%;降解28 d的适宜条件为组合三:菌量10%、温度30℃、土壤含水率15%、m(C)∶m(N)∶m(P)为100∶10∶1、表面活性剂1 000 mg·kg-1、Fenton试剂和植物油5%;降解52 d的适宜条件为组合三:菌量20%、温度20℃、土壤含水率35%、m(C)∶m(N)∶m(P)为120∶10∶1、表面活性剂500 g·kg-1、Fenton试剂和植物油为0。m(C)∶m(N)∶m(P)随着降解时间的延长影响作用逐渐减小。在降解的整个阶段,菌群组合的类型对于降解率的影响最大。对于降解14 d时,菌群组合二为最优菌群,对于降解28和52 d时,菌群组合三为最优菌群。     

化学预氧化-生物强化-生物刺激对土壤中菲降解的联合效应

通过室内实验,探究了低浓度过硫酸盐预氧化耦合生物强化或生物刺激技术处理下土壤中菲的降解率和修复效应。结果表明,浓度为0.1 mmol·g~(-1)、温度为50℃热活化的过硫酸钠对土壤中菲7 d的降解率为22.7%。预氧化后,加入高效降解菌和营养物质,强化微生物对菲的降解,继续培育21 d,最终降解率较第7天可提高8.08%～18.59%。同时添加高效降解菌和营养物质N,对土壤中菲的降解促进作用最强,最终降解率可达41.29%,较仅进行化学氧化的对照组和仅进行微生物降解的对照组分别提高17.44%和22.86%,较预氧化后不进行微生物强化的对照组提高12.9%。降解期间,土壤微生物数量和pH呈先下降,后上升趋势,最终维持在相对稳定水平。相关性分析结果表明,土壤中菲的降解率与氧化剂和营养物质N的添加呈显著正相关,土壤微生物数量与pH呈正相关,与氧化剂呈负相关,土壤pH与氧化剂及营养物质P呈负相关。研究结果证实了化学预氧化耦合生物强化和生物刺激技术能有效促进微生物对菲污染土壤的修复。     

不同植物-微生物联合修复体系下石油烃的降解

石油烃作为环境中广泛存在的有机污染物之一,对人体健康造成严重的危害。以位于天津的大港油田原油污染土壤中筛选出的耐低温高效石油烃降解菌为供试菌株,以小麦、紫花苜蓿作为供试植物,比较不同类型植物以及不同的外源菌接种方式对石油降解的影响,并采用荧光素比色法分析荧光素二乙酸酯(FDA)酶活性随时间的变化规律。经过70 d的降解,原状土壤的总石油烃含量从30 720 mg·kg~(-1)下降为26 800 mg·kg~(-1),降解率为12.76%。相比于小麦,紫花苜蓿对石油烃的降解具有更好的促进效果,降解率为24.85%。接种菌悬液后再种植植物时,石油烃降解效果接近于单独接种菌悬液处理。小麦-固定化外源菌处理条件下,降解率为21.10%,实验后期石油烃的降解速率远远高于其他处理,表现出良好的修复潜力。FDA酶活性经历了先下降、后上升再下降直至平缓的过程,并且受到种植植物和投加外源菌的影响。     

芘高效降解菌ZQ_5的培养条件及无机元素对其降解效率的影响

以从我国最大的石油污水灌区之一——沈抚灌区污染土壤分离到的以芘为惟一碳源、能源生长的高效降解菌株ZQ5为实验材料,通过对菌株ZQ5培养条件的优化,以及采用摇瓶振荡培养方法测定菌株ZQ5对不同浓度芘的降解率,表明：菌株ZQ5在30℃振荡培养16 d后对150 mg/L芘的降解率为90.31%。通过模拟稻田施用N、P和K肥等的土壤环境,探索了无机营养元素对降解菌ZQ5降解能力的影响,发现土壤中混合加入N、P和K无机营养元素的降解率能达到82%以上,比单加某种营养元素对降解菌ZQ5的降解效果好。本研究结果可以指导稻田PAHs的原位生物修复。     

芘高效降解菌ZQ5的培养条件及无机元素对其降解效率的影响

以从我国最大的石油污水灌区之一——沈抚灌区污染土壤分离到的以芘为惟一碳源、能源生长的高效降解菌株ZQ5为实验材料,通过对菌株ZQ5培养条件的优化,以及采用摇瓶振荡培养方法测定菌株ZQ5对不同浓度芘的降解率,表明:菌株ZQ5在30℃振荡培养16 d后对150 mg/L芘的降解率为90.31%。通过模拟稻田施用N、P和K肥等的土壤环境,探索了无机营养元素对降解菌ZQ5降解能力的影响,发现土壤中混合加入N、P和K无机营养元素的降解率能达到82%以上,比单加某种营养元素对降解菌ZQ5的降解效果好。本研究结果可以指导稻田PAHs的原位生物修复。     

Photodegradation and volatility of pesticides

BACKGROUND AND OBJECTIVES: Among the factors affecting the environmental fate of surface-applied pesticides several biological as well as abiotic factors, such as volatilization and photochemical transformations are of particular interest. Whereas reliable measurement methods and models for estimating direct photodegradation are already available for the compartments of water and atmosphere and individual subprocesses have already been described in detail, there is still a need for further elucidation concerning the key processes of heterogeneous photodegradation of environmental chemicals on surfaces. METHODS: In order to systematically examine the direct and indirect photodegradation of 14C-labeled pesticides on various surfaces and their volatilization behavior, a new laboratory device ('photovolatility chamber') was designed according to US EPA Guideline 161-3. Model experiments under controlled conditions were conducted investigating the impact of different surfaces, i.e. glass, soil dust and radish plants, and environmental factors, i.e. irradiation and atmospheric ozone (O3), on the photodegradation and volatilization of surface-deposited [phenyl-UL-14C]parathion-methyl (PM). RESULTS AND DISCUSSION: Depending on the experimental conditions, parathion-methyl was converted to paraoxon-methyl, 4-nitrophenol, unknown polar products and 14CO2. With respect to the direct photodegradation of PM (experiments without O3), the major products were polar compounds and 14CO2, due to the rapid photochemical mineralization of 4-nitrophenol to 14CO2. Paraoxon-methyl and 4-nitrophenol formation was mainly mediated by the combination of light, O3, and *OH radicals. In radish experiments PM photodegradation was presumably located in the cuticle compartment, which exhibited a sensitized photodegradation, as more unknown products were yielded compared to the glass and soil dust experiments. This could be explained by intensifying the inherent PM degradation in the dark with the same product spectrum. Due to photochemical product formation, which is an antagonistic process to the volatilization of parent compound, the volatilization of unaltered parathion-methyl from each surface generally decreased in the presence of light, particularly in combination with increasing O3 concentrations and *OH radical production rates. CONCLUSION: First results demonstrated that the photovolatility chamber provides a special tool for the systematic evaluation of (a) photodegradation of surface-located pesticide residues, i.e. measuring qualitative aspects of direct and indirect photodegradation together with relative photodegradation rates, and (b) volatilization of pesticides on surfaces by including and optionally varying relevant parameters such as light, atmospheric O3 concentration, surface temperature, air temperature, air flow rate. OUTLOOK: The experimental facility represents an important complement to lysimeter and field studies, in particular for experiments on the volatilization of pesticides using the wind tunnel system. With the photovolatility chamber special experiments on photodegradation, volatilization and plant uptake can be conducted to study key processes in more detail and this will lead to a better understanding of the effects of certain environmental processes on the fate of released agrochemicals contributing to an improved risk assessment.     

Toxicity of copper on rice growth and accumulation of copper in rice grain in copper contaminated soil

Pot soil experiments showed that copper (Cu) is highly toxic to rice. Rice grain yields decreased exponentially and significantly with the increase of soil Cu levels. Rice grain yield was reduced about 10% by soil Cu level of 100 mg kg(-1), about 50% by soil Cu level of 300-500 mg kg(-1) and about 90% by soil Cu concentration of 1,000 mg kg(-1). Root was more sensitive to soil Cu toxicity than other parts of rice plant at relatively lower soil Cu levels (less than 300-500 mg kg(-1)), but the growth of whole rice plant was severely inhibited at high soil Cu levels (300-500 mg kg(-1) or above). Cu concentrations in rice grain increased with soil Cu levels below 150-200 mg kg(-1), but decreased with soil Cu levels above 150-200 mg kg(-1), with peak Cu concentration at soil Cu level of 150-20 mg kg(-1). Cu was not distributed evenly in different parts of rice grain. Cu concentration in cortex (embryo) was more than 2-fold that in chaff and polished rice. More than 60% of the Cu in grain was accumulated in polished rice, about 24% in cortex (embryo), and about 12% in chaff. So, about 1/3 of the Cu in rice grain was eliminated after grain processing (chaff, cortex and embryo was removed).     

Amelioration of acidic soil using various renewable waste resources

In this study, improvement of acidic soil with respect to soil pH and exchangeable cations was attempted for sample with an initial pH of approximately 5. Acidic soil was amended with various waste resources in the range of 1 to 5 wt.% including waste oyster shells (WOS), calcined oyster shells (COS), Class C fly ash (FA), and cement kiln dust (CKD) to improve soil pH and exchangeable cations. Upon treatment, the soil pH was monitored for periods up to 3 months. The exchangeable cations were measured after 1 month of curing. After a curing period of 1 month, a maize growth experiment was conducted with selected-treated samples to evaluate the effectiveness of treatment. The treatment results indicate that in order to increase the soil pH to a value of 7, 1 wt.% of WOS, 3 wt.% of FA, and 1 wt.% of CKD are required. In the case of COS, 1 wt.% was more than enough to increase the soil pH value to 7 because of COS's strong alkalinity. Moreover, the soil pH increases after a curing period of 7 days and remains virtually unchanged thereafter up to 1 month of curing. Upon treatment, the summation of cations (Ca, Mg, K, and Na) significantly increased. The growth of maize is superior in the treated samples rather than the untreated one, indicating that the amelioration of acidic soil is beneficial to plant growth, since soil pH was improved and nutrients were replenished.     

Inefficiency of Mycobacterium chlorophenolicum PCP-1 to enhance mineralization of pentachlorophenol in soil microcosms

We examined the mineralization of pentachlorophenol (PCP) in sterile and non-sterile soil with or without added bacteria (Mycobacterium chlorophenolicum PCP-1). The soil used had no history of PCP contamination. Microcosms (30 g dry weight of soil) were incubated with labelled PCP (6.76% 13C, a non-radioactive stable isotope, 22 mg kg-1 dry weight) for 60 days. M. chlorophenolicum PCP-1 (7.8 x 10(6) cells g-1 dry weight) was added to some samples. 50% of the PCP was mineralized in non-sterile soil with or without the exogenous bacteria. Only 5% of the PCP was mineralized in sterile soil with or without bacteria. These data suggest that the PCP was not accessible to M. chlorophenolicum and that the indigenous soil microflora can mineralize PCP.     

Mercaptobenzothiazole-on-gold organic phase biosensor systems: 1. Enhanced organosphosphate pesticide determination

This paper reports the construction of the gold/mercaptobenzothiazole/polyaniline/acetylcholinesterase/polyvinylacetate (Au/ MBT/PANI/AChE/PVAc) thick-film biosensor for the determination of certain organophosphate pesticide solutions in selected aqueous organic solvent solutions. The Au/MBT/PANI/AChE/PVAc electrocatalytic biosensor device was constructed by encapsulating acetylcholinesterase (AChE) enzyme in the PANI polymer composite, followed by the coating of poly(vinyl acetate) (PVAc) on top to secure the biosensor film from disintegration in the organic solvents evaluated. The electroactive substrate called acetylthiocholine (ATCh) was employed to provide the movement of electrons in the amperometric biosensor. The voltammetric results have shown that the current shifts more anodically as the Au/MBT/PANI/AChE/PVAc biosensor responded to successive acetylthiocholine (ATCh) substrate addition under anaerobic conditions in 0.1 M phosphate buffer, KCl (pH 7.2) solution and aqueous organic solvent solutions. For the Au/MBT/PANI/AChE/PVAc biosensor, various performance and stability parameters were evaluated. These factors include the optimal enzyme loading, effect of pH, long-term stability of the biosensor, temperature stability of the biosensor, the effect of polar organic solvents, and the effect of non-polar organic solvents on the amperometric behavior of the biosensor. The biosensor was then applied to detect a series of 5 organophosphorous pesticides in aqueous organic solvents and the pesticides studied were parathion-methyl, malathion and chlorpyrifos. The results obtained have shown that the detection limit values for the individual pesticides were 1.332 nM (parathion-methyl), 0.189 nM (malathion), 0.018 nM (chlorpyrifos).     

Washing of Pb contaminated soil using [S,S] ethylenediamine disuccinate and horizontal permeable barriers

The feasibility of in situ washing of soil contaminated with Pb (6.83 mmol kg(-1)) using biodegradable chelator, [S,S] stereoisomere of ethylenediamine disuccinate ([S,S]-EDDS) and horizontal permeable barriers was examined in soil columns. After 4-cycles of 10 mmol kg(-1) soil [S,S]-EDDS applications, followed by irrigation, 24.7% of total initial Pb was washed from the contaminated soil and accumulated into the barrier. Sequential extractions indicated that washing removed most of the Pb from the organic soil fraction. Barriers were positioned 20 cm deep in the soil and consisted of a 2 cm layer of nutrient enriched vermiculite. Barriers reduced leaching of Pb in the first cycle of [S,S]-EDDS addition by more than 500-times compared to columns with no barrier. After four cycles of chelator addition, a total of 0.24% of the initial Pb was leached from the columns with barriers. Four cycles of in situ soil washing in soil columns were less effective than simulated ex situ soil washing with 40 mmol kg(-1) [S,S]-EDDS, where 51.0% of the Pb was removed after 48-h extraction. Ex situ soil washing with 10 mmol kg(-1) [S,S]-EDDS was equally effective as the first cycle of in situ soil washing (15.5% and 14.5% of removed Pb, respectively).     

Soil distribution of fipronil and its metabolites originating from a seed-coated formulation

Seed-coating with the insecticide fipronil has been intensively used in sunflower cultivation to control soil pests such as wireworms. A research project was undertaken to determine the soil distribution of fipronil and of its main phenylpyrazole metabolites. Under agronomic conditions, the quantity of fipronil in the seed-coat (437 microg/seed) decreased continuously during the cultivation period (3.9 microg day(-1) during the first two months; 0.3 microg day(-1) during the next four months). At the end of the cultivation period, 42% of all phenylpyrazole compounds remained in the seed-coat. Fipro nil was poorly mobile in soil, and at the end of the cultivation period it was mostly concentrated in the soil layer close to the seed (3240 microg kg(-1) soil). Starting from the seed-coating, a fipronil concentration gradient was measured in the soil, up to a distance of 11 cm from the seed. Degradation in the soil occurred at a moderate rate, probably due to the fact that water solubilization of the solid active ingredient present in the seed coating was rate limiting. Indeed, after 6 months of cultivation, only 51% of the fipronil seed-coating was found in the soil, about 7% having been absorbed by the sunflower plant, and 42% remaining in the seed coat. The predominant metabolites produced in the soil were sulfone-fipronil, sulfide-fipronil and amide-fipronil, which were produced at average rates of 5 microg kg(-1) soil day(-1), 3 microg kg(-1) soil day(-1), and 0.4 microg kg(-1) soil day(-1), respectively. In contrast, the photoproduct, desulfinyl-fipronil, was barely detected. All phenylpyrazole compounds were poorly mobile, except for the amide derivative, which is devoid of insecticidal activity in marked contrast to the other metabolites. Furthermore, detectable soil contamination was limited to a zone of about 11 cm around the seed.     

Eisenia fetida increased removal of polycyclic aromatic hydrocarbons from soil

The removal of phenanthrene, anthracene and benzo(a)pyrene added at three different concentrations was investigated with or without earthworms (Eisenia fetida) within 11 weeks. Average anthracene removal by the autochthonous micro-organisms was 23%, 77% for phenanthrene and 13% for benzo(a)pyrene, while it was 51% for anthracene, 47% for benzo(a)pyrene and 100% for phenanthrene in soil with earthworms. At 50 and 100mg phenanthrene kg(-1)E. fetida survival was 91% and 83%, but at 150 mg kg(-1) all died within 15 days. Survival of E. fetida in soil amended with anthracene < or = 1000 mg kg(-1) and benzo(a)pyrene < or = 150 mg kg(-1) was higher than 80% and without weight loss compared to the untreated soil. Only small amounts of PAHs were detected in the earthworms. It was concluded that E. fetida has the potential to remove large amounts of PAHs from soil, but more work is necessary to elucidate the mechanisms involved.     

Influence of salinity on bioremediation of oil in soil

Spills from oil production and processing result in soils being contaminated with oil and salt. The effect of NaCl on degradation of oil in a sandy-clay loam and a clay loam soil was determined. Soils were treated with 50 g kg(-1) non-detergent motor oil (30 SAE). Salt treatments included NaCl amendments to adjust the soil solution electrical conductivities to 40, 120, and 200 dS m(-1). Soils were amended with nutrients and incubated at 25 degrees C. Oil degradation was estimated from the quantities of CO(2) evolved and from gravimetric determinations of remaining oil. Salt concentrations of 200 dS m(-1) in oil amended soils resulted in a decrease in oil mineralized by 44% for a clay loam and 20% for a sandy-clay loam soil. A salt concentration of 40 dS m(-1) reduced oil mineralization by about 10% in both soils. Oil mineralized in the oil amended clay-loam soil was 2-3 times greater than for comparable treatments of the sandy-clay loam soil. Amending the sandy-clay loam soil with 5% by weight of the clay-loam soil enhanced oil mineralization by 40%. Removal of salts from oil and salt contaminated soils before undertaking bioremediation may reduce the time required for bioremediation.     

Benzo[a]pyrene removal from soil by Phanerochaete chrysosporium grown on sugarcane bagasse and pine sawdust

The capacity of Phanerochaete chrysosporium grown on soil with added sugarcane baggase (BP) and pine sawdust (PS) to remove benzo(a)pyrene (BaP) was studied. A half factorial two-level experiment 2(4-1) was designed to determine the effect of: type of lignocellulosic material (BP and PS) for fungus growth, age of fungus (5 and 10d), amount of lignocellulosic material (10% and 15% w/w) and soil moisture content (water holding capacity of 45% and 56% w/w). Inoculum obtained at different ages showed that the capacity of P. chrysosporium to remove BaP depends on the lignocellulosic used and on inoculum age. Abiotic BaP removal was affected significantly (p<0.05) by inoculum age, type of lignocellulosic added and soil moisture content. The removal of BaP by lignocellulosic material was more effective by young inocula (71.97 mg BaP kg(-1) dry soil), with high percentage of added lignocellulosic (71.57 mg BaP kg(-1) dry soil) and at low soil moisture content (73.07 mg BaP kg(-1) dry soil). When fungus was grown on BP, maximum BaP removal rate was obtained at 5d of incubation (10.85 mg BaP d(-1)l(-1) and 50.12 mg BaP kg(-1) dry soil), while in PS maximum BaP removal was obtained at 10d of incubation (12.06 mg BaP d(-1)l(-1) and 39.94 mg BaP kg(-1) dry soil).