动电技术去除城市污泥中重金属的可行性探讨

本文简要介绍了我国城市污泥的处理处置和利用现状及动电技术去除重金属的基本原理,分析动电技术处理土壤中重金属的国内外的试验研究和应用情况,对动电技术处理城市污泥中重金属的可行性进行探讨,认为动电技术去除城市污泥中的重金属具有可行性,并提出了今后研究的方向.     

Biosorption of heavy metals by activated sludge and their desorption characteristics

The biosorption of different metals (Cu2+, Cd2+, Zn2+, Ni2+ and Pb2+) was investigated using activated sludge. The optimum pH was 4 for Cd, Cu and Pb sorption and 5 for Ni and Zn. Biomass metal uptake clearly competed with protons present in the aqueous medium, making pH an important variable in the process. Protons consumed by biomass in control tests versus protons exchange in biosorption tests confirmed a maximum exchange between metal cations and protons at pH 2. The study of the influence of biomass concentration revealed that the amount of protons released from biomass increased with biomass concentration. This would confirm the hypothesis of ion exchange between both types of ions. The application of the Langmuir and Freundlich models showed a better fitting of experimental data to the first model. The maximum sorption uptake of the studied metals by the activated sludge showed the following decreasing order: Pb>Cu>CdZn>Ni. Desorption experiments showed that HCl was a good eluent for the five metals tested, particularly at low pH values (1 and 2). At pH 3 or 4 the desorption yield was significantly lower. However, its use did not allow the reuse of biomass in subsequent loading and unloading cycles. EDTA was also a good desorption agent, achieving the total recovery for the five metals tested at a concentration of 1mM, with the advantage that biomass could be reused for three sorption-desorption cycles.     

Immersion frying for the thermal drying of sewage sludge: an economic assessment

This paper presents an economic study of a novel thermal fry-drying technology which transforms sewage sludge and recycled cooking oil (RCO) into a solid fuel. The process is shown to have significant potential advantage in terms of capital costs (by factors of several times) and comparable operating costs. Three potential variants of the process have been simulated and costed in terms of both capital and operating requirements for a commercial scale of operation. The differences are in the energy recovery systems, which include a simple condensation of the evaporated water and two different heat pump configurations. Simple condensation provides the simplest process, but the energy efficiency gain of an open heat pump offset this, making it economically somewhat more attractive. In terms of operating costs, current sludge dryers are dominated by maintenance and energy requirements, while for fry-drying these are comparatively small. Fry-drying running costs are dominated by provision of makeup waste oil. Cost reduction could focus on cheaper waste oil, e.g. from grease trap waste.     

Characteristics of slag, fly ash and deposited particles during melting of dewatered sewage sludge in a pilot plant

This study examines slag, fly ash, and deposited particles during melting of dewatered sewage sludge in a pilot plant. In addition, the chemical composition of particles in flue gas was simulated using a thermodynamics program, namely FACTSage 5.2. The results showed that the main components of slag were Al, Fe, Ca, P and Si; the minor components were Na, K, Mg, Cu, and Zn. The main chemical compound of slag was Ca4(Mg,Fe)5(PO4)6. For fly ash particles, heavy metals with the highest concentrations were in the order of Zn and As, Pb, Cu, and Cd, respectively. For non-heavy metals, Al, Fe and P were also found in significant amounts. The majority of deposited particles were composed of elements of Zn, P, S, Na, Fe, Al, Si, and Ca and such chemical compounds as Zn3(PO4)2, AlPO4, FePO4 and Fe(OH)3 while the minority consisted of elements of As, Cu, and Pb. Moreover, the compositions of deposited particles in each chamber differed due to different flue gas temperatures inside. In the secondary chamber at 760 degrees C, the amounts of Fe and Al were higher than Zn, whereas, in the other chambers (600-400 degrees C), the amount of Zn was higher. In other words, at the lower temperature the deposition of Zn was higher than the deposition of Fe and Al. In the water cooling section, volatile elements (i.e. Zn, As, Cu, Pb) were found in the highest concentrations due to a big difference in temperature between the wall surface and flue gas. From the simulation results, most of the elements in the gas phase were found to be chloride compounds, whereas those in the solid phase were in the form of oxide, sulfate, and phosphate compounds.     

Removal of heavy metal ions from wastewaters: a review

Heavy metal pollution has become one of the most serious environmental problems today. The treatment of heavy metals is of special concern due to their recalcitrance and persistence in the environment. In recent years, various methods for heavy metal removal from wastewater have been extensively studied. This paper reviews the current methods that have been used to treat heavy metal wastewater and evaluates these techniques. These technologies include chemical precipitation, ion-exchange, adsorption, membrane filtration, coagulation-flocculation, flotation and electrochemical methods. About 185 published studies (1988-2010) are reviewed in this paper. It is evident from the literature survey articles that ion-exchange, adsorption and membrane filtration are the most frequently studied for the treatment of heavy metal wastewater.     

Leaching characteristics of heavy metals from sewage sludge by Acidithiobacillus thiooxidans MET

An acidophilic, sulfur-oxidizing Acidithiobacillus thiooxidans MET bacterium was isolated from anaerobically digested, dewatered sewage sludge. This bacterium showed sulfur-oxidizing ability at both acidic and neutral conditions, and allowed metal leaching even at a high (130 g L(-1)) sludge solids concentration. We found that low metal leaching efficiency at high solids concentration was mainly due to an increase in buffering capacity resulting in retardation of pH reduction. Therefore, metal leaching was mainly influenced not by sludge solids concentration, but by the pH (or sulfate concentration per unit sludge mass) of the sludge solutions. The relationship between the pH of the sludge solution and the efficiency of metal leaching was obtained by quantitatively investigating the effect of pH reduction or the amount of sulfate produced per unit sludge mass on leaching of each metal. Furthermore, the relationship between total metal content in the sludge and metal leached to the solution was obtained for each metal. Such a relationship allowed estimation of leachable metal at various amounts of total metal content in sludge.     

Bioproduction of ferric sulfate used during heavy metals removal from sewage sludge

Toxic metals removal from wastewater sewage sludge can be achieved through microbial processes involving Acidithiobacillus ferrooxidans. The oxidation of ferrous ions by A. ferrooxidans, cultured in sewage sludge filtrate, was studied in both batch and continuous flow stirred tank reactors. Sewage sludge filtrate containing natural nutrients (phosphorus and nitrogen) was recovered as effluent following the dehydration of a primary and secondary sludge mixture. Batch and continuous flow stirred tank reactor tests demonstrated that A. ferrooxidans were able to grow and completely oxidize ferrous iron in a culture medium containing more than 80% (v v(-1)) sewage sludge filtrate with 10 g Fe(II) L(-1) added. Toxic levels were reached when total organic carbon in the sewage sludge filtrate exceeded 250 mg L(-1). The ferric iron solution produced in the sludge filtrate by A. ferrooxidans was used to solubilize heavy metals in primary and secondary sludge. The solubilization of Cu, Cr, and Zn yielded 71, 49, and 80%, respectively. This is comparable with the yield percentages obtained using a FeCl(3) solution. The cost of treating wastewater sewage sludge by bioproducing a ferric ion solution from sewage sludge is three times less expensive than the conventional method requiring a commercial ferric chloride solution.     

Zinc distribution in soils amended with different kinds of sewage sludge

Sewage sludge (SS) can be applied to cropland to supply and recycle nutrients and organic carbon. Potentially toxic elements in the sludge, however, are of environmental concern. This study evaluates the changes in chemical speciation of Zn in three representative pristine soils of the Pampas Region, Argentina, measured with sequential extraction over a one-year period. Pure SS or SS containing 30% (DM) of its own incineration ash (AS) was applied to the soils at an application rate of 150Mgha(-1). Zn was sequentially fractionated into exchangeable, organically bound, inorganic and residual fractions. The application of the SS and AS amendments significantly increased Zn concentration in all soil fractions at each sampling date. At day 1, Zn was mainly found in the residual fraction. A year after the application of the amendments, redistribution towards the inorganic fraction was observed (41-76% of total Zn content). Zn found in exchangeable and inorganic fractions depended on soil pH rather than on the type of soil used. A negative and significant correlation was found between exchangeable Zn concentrations and soil pH (r=0.94), and a positive and significant correlation between inorganic Zn concentrations and soil pH (r=0.92). For each amended soil and sampling date, no significant differences were observed between SS or AS treatments for the exchangeable fraction. Moreover, the use of AS did not cause significant differences in Zn concentration in the other soil fractions compared to SS. Based on these results, land spreading of AS may be similar to SS diaposal in terms of Zn mobility.     

Environmental assessment of supercritical water oxidation of sewage sludge

Environmental aspects of using supercritical water oxidation (SCWO) to treat sewage sludge were studied using a life cycle assessment (LCA) methodology. The system studied is the first commercial scale SCWO plant for sewage sludge in the world, treating sludge from the municipal wastewater treatment facility in Harlingen, TX, USA. The environmental impacts were evaluated using three specific environmental attributes: global warming potential (GWP), photo-oxidant creation potential (POCP) and resource depletion; as well as two single point indicators: EPS2000 and EcoIndicator99. The LCA results show that for the described process, gas-fired preheating of the sludge is the major contributor to environmental impacts, and emissions from generating electricity for pumping and for oxygen production are also important. Overall, SCWO processing of undigested sewage sludge is an environmentally attractive technology, particularly when heat is recovered from the process. Energy-conserving measures and recovery of excess oxygen from the SCWO process should be considered for improving the sustainability potential.     

Effect of liming on the distribution of heavy metals in untreated industrial sewage sludge produced in Pakistan for the cultivation of <Emphasis Type="Italic">Sorghum bicolor</Emphasis> (L.)

The recycling of sewage sludge on agriculture land represents an alternative, advantageous, disposal of this waste material. The aim of the present study was to evaluate the feasibility of using industrial sewage sludge, produced in Pakistan, as a fertiliser. Agricultural soil amended with 25% (w/w) sewage sludge with or without lime treatment was used for growing a variety of sorghum (PARC-SS-1). The mobility of the heavy metals (HMs) (Cd, Cu, Cr, Ni, Pb and Zn) and metalloid (As) in the untreated industrial waste water sewage sludge (UIWS) samples were assessed by applying a modified BCR (Community Bureau of Reference) sequential extraction procedure. The single extraction procedure comprised of the application of mild extractant (CaCl₂) and water for the estimation of the proportion of easily soluble metal fractions. The precision and accuracy of BCR was evaluated by using a certified reference material of soil amended with sewage sludge BCR 483. The plant available metal contents, as extracted by the deionised water and 0.01 M CaCl₂ solution and exchangeable fraction of BCR sequential, decreased with lime application in the range of 10–44% for As, Cr, Ni, Pb and Zn, except in the cases of Cd and Cu, where their mobility was increased by 10% and 24%, respectively. Sludge amendment enhanced the dry weight yield of sorghum and the increase was more obvious after liming up to 25%. The uptake of HMs were lower in test samples (3.2–21.8%), except for Cu and Cd, which was higher (4%), while they were below the permissible limit of these metals. The present experiment demonstrates that liming was important in factors facilitating the growth of sorghum in sludge-amended soil.     

Effects of nano-SiO(2) and different ash particle sizes on sludge ash-cement mortar

The effects of nano-SiO₂ on three ash particle sizes in mortar were studied by replacing a portion of the cement with incinerated sewage sludge ash. Results indicate that the amount of water needed at standard consistency increased as more nano-SiO₂ was added. Moreover, a reduction in setting time became noticeable for smaller ash particle sizes. The compressive strength of the ash–cement mortar increased as more nano-SiO₂ was added. Additionally, with 2% nano-SiO₂ added and a cure length of 7 days, the compressive strength of the ash–cement mortar with 1 μm ash particle size was about 1.5 times better that of 75 μm particle size. Further, nano-SiO₂ functioned to fill pores for ash–cement mortar with different ash particle sizes. However, the effects of this pore-filling varied with ash particle size. Higher amounts of nano-SiO₂ better influenced the ash–cement mortar with larger ash particle sizes.     

用观察活性污泥的方法判断污水处理情况

通过观察活性污泥的色、嗅、数量、质量和微生物生长等情况，判断活性污泥性状的优劣以控制污水处理系统的运行状况，并查明出现异常的原因，达到污水处理的最佳效果。     

城市污水厂混合污泥好氧消化处理研究

以城市污水处理厂的初沉污泥与剩余污泥的混合污泥为对象,研究了影响污泥好氧消化处理的各项因素.通过测定氧摄取速率(OUR)和此污泥好氧速率(SOUR),对实验结果进行了探讨.     

Environmental risks of applying sewage sludge compost to vineyards: carbon,heavy metals,nitrogen, and phosphorus accumulation

Biosolids are applied to vineyards to supply organic matter. However, there is concern that this practice can increase the concentration of macronutrients and heavy metals in the soil, some of which can leach. We evaluated the environmental hazard of sewage sludge compost applied in March 1999 at 10, 30, and 90 Mg ha-1 fresh weight in a vineyard in southeastern France. Soil organic matter increased in all plots by 3 g kg-1 18 mo after the amendment. Neither total nor available heavy metal concentrations increased in the soil. Mineral nitrogen (N) in the topsoil of amended plots of 10, 30, and 90 Mg ha-1 increased by 5, 14, and 26 kg (NO3(-)-N + NH4(+)-N) ha-1, respectively, the first summer and by 2, 5, and 10 kg (NO3(-)-N + NH4(+)-N) ha-1, respectively, the second summer compared with controls. At the recommended rate, risks of N leaching is very low, but phosphorus (P) appeared to be the limiting factor. Phosphorus significantly increased only in plots amended with the highest rate in the topsoil and subsoil. At lower rates, although no significant differences were observed, P added was greater than the quantities absorbed by vines. In the long run, P will accumulate in the soil and may reach concentrations that will pose a risk to surface waters and ground water. Therefore, although the current recommended rate (10 Mg ha-1) increased soil organic matter without the risk of N leaching, total sewage sludge loading rates on vineyards should be based on P concentrations.     

Sustainable options of post treatment of UASB effluent treating sewage: A review

The upflow anaerobic sludge blanket (UASB) process is reported to be a sustainable technology for domestic wastewaters treatment in developing countries and for small communities. However, the inability of UASB process to meet the desired disposal standards has given enough impetus for subsequent post treatment. In order to upgrade the UASB based sewage treatment plants (STPs) to achieve desired effluent quality for disposal or for reuse, various technological options are available and broadly differentiated as primary post-treatment for the removal of organic and inorganic compounds and suspended matter; secondary post-treatment for the removal of hardly degradable soluble matter, colloidal and nutrients; and polishing systems for removals of pathogens. Hence, this paper discusses the different systems for the treatment of UASB reactor effluent treating sewage. Additionally, a comparative review, an economic evaluation of some of the emerging options was conducted and based on the extensive review of different integrated combination, i.e. UASB-different aerobic systems, a treatment concept based on natural biological mineralization route recognized as an advanced technology to meet all practical aspects to make it a sustainable for environmental protection, resource preservation and recovering maximum resources.     

活性污泥吸附重金属Cr6+的研究

以活性污泥为材料，采用不同时间、温度、pH进行吸附重金属Cr^6 的研究。实验结果表明，当吸附时间为15min，吸附温度为28℃，吸附pH=7时具有较好吸附效果。在此条件下，当重金属Cr^6 浓度为50mg/L，其吸附率可达97．2％。     

Bacterial pretreatment enhances removal of heavy metals during treatment of post-methanated distillery effluent by Typha angustata L

A combination of bacterial pretreatment followed by free water surface flow through wetland plants was investigated to determine its effect on removal of heavy metals in bioremediation of post-methanated distillery effluent (PMDE). The bacterial pretreatment was intended to transform the metal complexes and organic pollutants into simpler, biologically assimilable molecules. The 10% and 30% v/v concentrations of PMDE favored luxuriant bacterial growth; the 50% concentration supported less growth, whereas the undiluted effluent (i.e., 100%) supported very little bacterial growth. The use of bacterial pretreatment combined with the constructed wetland system greatly increase the overall bioaccumulation of all heavy metals by the plants compared with the control treatment. However, the integration of bacterial pretreatment of PMDE with the Typha angustata resulted in enhanced removal of Cd (34.02–61.50% increase), Cr (35.90–57.60% increase), Cu (32.88–54.22% increase), Fe (32.50–51.26% increase), Mn (35.99–82.85% increase), Ni (35.85–59.24% increase), Pb (33.45–59.51% increase) and Zn (31.95–53.70% increase) compared with a control that lacked this pretreatment. In addition to the bioaccumulation of these heavy metals, several physico-chemical parameters also improved at the 30% effluent concentration: color, BOD, COD, phenol and total nitrogen decreased by 98.33%, 98.89%, 98.50%, 93.75% and 82.39%, respectively, after 7 days of free water surface flow treatment. The results suggest that bacterial pretreatment of PMDE, integrated with phytoremediation will improve the treatment process of PMDE and promote safer disposal of this waste.     

Determining contamination level of heavy metals in road dust from busy traffic areas with different characteristics

This study identified the levels and sources of heavy metal contamination in road dust from busy traffic areas in a typical industrial city in Korea. This study compared the total concentrations, as determined by aqua regia digestions and atomic absorption spectroscopy, of cadmium (Cd), copper (Cu), lead (Pb), zinc (Zn) and nickel (Ni) in the road dust from areas with different characteristics such as traffic rotaries, downtown areas, circulation roads, and asphalt and concrete highways. The contamination levels of the heavy metals in the road dust were evaluated using the contamination factor and the degree of contamination. The contamination levels of the heavy metals in the road dust were highly dependent on traffic volume and atmospheric dispersion from traffic rotaries. Industrial emissions and the frequency of brake use and vehicles coming to a complete stop were additional factors that affected the contamination levels in downtown areas. The concrete highway had higher contamination levels of the heavy metals than the asphalt highway. Vehicle speed was also a strong contributing factor to the degree of contamination of heavy metals in the road dust from the circulation roads and highways.     

Application of treated wastewater and digested sewage sludge to obtain biodiesel from Helianthus annuus L. seeds oil

Waste from wastewater treatment plants (WWTP) for Helianthus annuus L. production may be a viable solution to obtain biodiesel. This study achieved two objectives: assess the agronomical viability of waste (wastewater and sludge) from the Alcázar de San Juan WWTP in central Spain for H. annuus L. production; use H. annuus L. seeds grown in this way to obtain biodiesel. Five study plots, each measuring 6 m × 6 m (36 m²), were set up on the agricultural land near the Alcázar de San Juan WWTP. Five fertilizer treatment types were considered: drinking water, as the control; treated wastewater; 10 t ha^?1 of air-dried sewage sludge; 20 t ha^?1 of air-dried sewage sludge; 0.6 t ha^?1 of commercial inorganic fertilizer. Soil, irrigation water, sewage sludge, crop development and fatty acid composition in achenes oil were monitored. The 20 t ha^–1 dose of sewage sludge proved effective to grow H. annuus L. with similar results to those grown with a commercial fertilizer. However, precautions should be taken when irrigating with wastewater because of high salinity and nutrient deficiency. Sunflower oil was composed mostly of linoleic and oleic acid. The remaining fatty acids were linolenic, estearic, nervonic, palmitoleic, and palmitic.     

Utilization of pulp and paper industrial wastes to remove heavy metals from metal finishing wastewater

Two pulp and paper industrial wastes, lime mud (LM) and recovery boiler ash (RB), have low moisture contents, low heavy metal contaminations and contain various carbonate compounds which contribute to a high pH. Metal finishing wastewater (MF-WW) has a low pH, high levels of TDS and high contaminations from Cr, Cu, Pb and Zn. The heavy metals from MF-WW were removed by sorption and precipitation mechanisms. LM gave better results in removing heavy metals from MF-WW than RB. At a reaction time of 45 min, the maximum removal efficiencies for Cr (93%) and Cu (99%) were obtained at 110 g L⁻¹ of LM, but at 80 g L⁻¹ for Pb (96%) and Zn (99%). Treatment with LM gives a higher sludge volume than with RB. However, the leachability of heavy metals from LM is lower. Leachability of heavy metals in the sediment for all selected treatment conditions is within government standards.