Air Pollution Potential: Regional Study in Argentina

/ Air pollution potential is a measure of the atmospheric conditions that are unable to transport and dilute pollutants into the air, independently of the existence of sources. This potential can be determined from two atmospheric parameters: mixing height and transport wind. In this paper a statistical analysis of the mixing height and transport wind, in order to determine the areas with high or poor atmospheric ventilation in Argentina, is presented. In order to achieve this, meteorological data registered during 1979-1982 at eight meteorological stations were used. Daily values of the maximum mixing height were calculated from observations of daily temperatures at different heights and maximum surface temperature. At the same time as the maximum mixing height, the values of the transport wind were determined from the surface windspeed and the characteristics of the ground in the surroundings of each meteorological station. The mean seasonal values for both parameters were obtained. Isopleths of the mean seasonal of the maximum mixing heights were drawn. The percentage of seasonal frequencies of poor ventilation conditions were calculated and the frequency isopleths were also drawn to determine areas with minor and major relative frequencies. It was found that the northeastern and central-eastern regions of Argentina had a high air pollution potential during the whole year. Unfavorable atmospheric ventilation conditions were also found in the central-western side of the country during the cold seasons (37.5% in autumn and 56.9% in winter). The region with the greatest atmospheric ventilation is located south of 40 degrees S, where the frequency of poor ventilation varies between 8.0% in summer and 10.8% in winter.     

成都市温江边界层风场特征的研究

着眼于成都地区污染气象特征,利用温江2004年~2012年的地面观测资料及同期的探空资料,对该地区风场的统计特征进行了分析。结果表明:(1)从风频而言,温江地面风春、夏、秋3季均以偏北风为主,冬季则以东北风为主,因此,全年的主导风为偏北风。(2)从风速而言,区域静风和小风频率较高,占全年的68.7%;近10年来,温江年和4季的平均风速均呈现出减小趋势。(3)基于修正的帕斯奎尔稳定度分级法,利用幂指数律公式拟合了风随高度的变化,发现风廓线指数比国标值偏高,并随稳定度的增加而增大。(4)风速、稳定度联合频率的大值区主要出现在风速小于3m/s、稳定度为D~E类。上述研究成果对区域大气环境规划和工程治理具有重要的参考价值。     

Evaluation of the efficiency of some sediment trapping methods after a Mediterranean forest fire

Forest fires are common in Mediterranean environments and may become increasingly more frequent as the climate changes. Destruction of the forest cover and litter layer leads to greater overland flow and increased erosion rates. The greatest risk occurs during the first rainstorms following a major fire, so local authorities must act quickly to put erosion control methods in place in order to avoid excessive post-fire sediment loads in river channels. Deciding on which methods to use requires accurate knowledge of their impact on sediment load and an estimate of their cost efficiency. The objective of this study was to evaluate the efficiency of Log Debris Dams (LDDs) and a sedimentation basin for their effectiveness in trapping sediments. Paired sub-catchments were studied to quantify the amount of sediments trapped in stream channels by a series of LDDs and a sedimentation basin. Cost efficiency was evaluated for each of the measures as a function of the cost per unit volume of sediments trapped. In addition, grain size analyses were performed to characterise the nature of the sediments trapped. A third sediment trapping method, Log Erosion Barriers (LEBs) was evaluated more superficially than the first two and conclusions regarding this method are tentative. LDDs trapped a mean volume of 1.57 m³ per unit (median = 1.28 m³); mean LDD height was 105.4 cm (std. dev. = 21.9 cm), and mean height of trapped sediments was only 50.0 cm (std. dev. = 22.9 cm), showing that the traps were only half filled. Sediment height was limited by the presence of gaps between logs or branches that allowed runoff to flow through. Comparison of the textural characteristics of slope and trapped sediments showed distinct sorting: particles greater than 20 mm were not mobilised from the slopes during the study period, sediments in the medium to coarse sand size fractions were trapped preferentially by the LDDs, and sediments in the sedimentation basin were enriched by clay and silt sized (<0.050 mm) particles as coarser sediments were trapped upstream by the LDDs. Cost efficiency of LDDs was estimated at about 143 € m⁻³ for the LDDs and 217 € m⁻³ for the sedimentation basin at the time of sampling. The LDDs are therefore a cost effective method of trapping sediments, but they can only be used when pine trees or straight-trunked trees are locally available. In this case, they should be combined with LEBs, which had a cost efficiency estimated at about 250 € m⁻³. Installation of the LEBs had not been optimised and they have the advantage of trapping sediments on the slopes where they can continue to play an ecological role, so this method can give better results with more care. Sedimentation basins can be emptied if necessary and are useful in areas where pine trees are not available and where the site can be secured.     

Cargo-specific accidental release impact zones for hazardous materials: risk and consequence comparison for ammonia and hydrogen fluoride

Impacts of hazardous material releases during transport depend on the characteristics of the cargo, incident location and time, weather conditions (i.e., wind direction and speed), and land use. The objectives of this research were to characterize the dispersion characteristics of two hazardous materials (ammonia and hydrogen fluoride) in relation to meteorological parameters, land use, and cargo characteristics; and evaluate the health risks associated with the exposure after accidental releases. The magnitudes of the impact zones were compared in relation to atmospheric stability and exposure levels. Impact zones were estimated by areal locations of hazardous atmospheres software and imported to ArcGIS. For ammonia, the areas impacted by exposure levels over 1100 ppm Acute Exposure Guideline Level 3 (AEGL-3) were limited to less than 0.3 miles downwind from the incident location under unstable atmospheric conditions, which favor high vertical mixing and rapid dilution, and extended further downwind to distances between 0.5 and 0.7 miles under stable atmospheric conditions. For hydrogen fluoride, the AEGL-3 impact zone (exposure levels over 44 ppm) extended between 0.6 and 0.9 miles directly downwind from the incident location under unstable conditions, and reached approximately 2.0 miles directly downwind from the incident location under stable atmospheric conditions. The results were compared with the Emergency Response Guideline (ERG 2012) and showed agreement. The multilevel analysis of impacts after hazardous material releases during transport (i.e., type of material, geographical data, dispersion profile, meteorological information) can be used for implementing appropriate response and mitigation measures for accidental releases of hazardous cargo.     

Economic implications of long distance commuting in the Chilean mining industry

More than 10% of the labor force that works in Antofagasta lives in other regions, commuting on average more than 800 km in a shift system that allows working several days in a row followed by several days off. The mining industry is the main contractor of such workers and the impact of the process spreads through the rest of the Chilean territory.Using an input-output approach, this paper shows that a significant amount of resources generated by the mining industries in the Region of Antofagasta goes to other regions in wages earned by commuters who have decided to work in this region but live in another. The commuting process seems to be driven by centripetal forces that support centralization, thus arguing for regional policies to promote the attractiveness of the peripheral regions.     

A harvest failure approach to assess the threat from an invasive species

We present the idea of using potential infringements on annual allowable harvest targets as an approach to estimate threats from invasive species to the forest products sector. The approach uses present-day harvest levels as a reference level to estimate when and where the impact of a nonnative forest pest could become economically damaging. We use a generic model that simulates spread and damage by nonnative invasive species, basic harvest and forest growth through time. The concept is illustrated with a case study of a new nonnative invasive pest, Sirex noctilio Fabricius on pine resources in eastern Canada. Impacts of invasion on wood supply, in particular, the point at which present-day harvest levels are not attainable, were identified for 77 non-overlapping geographical regions that delimit the primary wood supply areas around large mills and wood processing facilities in eastern Canada. The results identify the minimum area of a pest outbreak that could trigger harvest shortages (approximately 12.5–14 M ha of pine forests in Ontario and Quebec). Beyond this level, the amount of host resource available for harvesting in any given year declines rapidly. The failure to sustain broad-scale harvest targets may be an attractive and intuitive indicator for policy makers and regulators interested in developing control and “slow-the-spread” programs for non-native forest pests.     

柳州市灰霾日不利天气分析

灰霾的发生对城市形象和人体健康都造成不利的影响,而灰霾的出现常常与不利的天气条件结合紧密,成为引发灰霾的重要因素。本文通过统计柳州市2002年~2012年间不同的天气条件下灰霾发生的概率,并结合2008年~2012年的柳州市实际空气质量状况,明确灰霾发生的主要污染物,同时通过2012年具体的气象特征和天气形势找出与灰霾发生密切相关的天气因素。经过分析,可吸入颗粒物(PM10)为大部分灰霾日的首要污染物,且低风速、中低湿度、不利于污染物扩散的风向及弱冷高压和鞍形场等不利气象条件易使污染物聚集,加速了灰霾日的形成,是灰霾日发生的重要因素。这些不利天气情况的分析统计,为柳州市建立灰霾日预警系统提供了有力支持。     

A港区海上溢油事故数值模拟预测

为研究A港区溢油事故的影响,通过MIKE21软件建模、并综合考虑风向、风速和潮流等因素设定6种不同情景进行模拟预测。结果显示,在不利风条件下,72 h油膜扩散距离为0.7~39.50 km,扫海面积可达0.03~142.97 km²,风场对油粒子的漂移和扩散起决定性作用,潮流场次之。通过模拟预测,为加强区域溢油应急联动、充分利用周边溢油应急资源,做好溢油应急防范提供参考。     

Wind energy and natural ventilation potential of a wind catcher in Yazd – Iran (a long-term measurement)

When designing energy efficient buildings it is useful to study existing climate—responsive building typologies. The wind towers or wind-catchers of Yazd city in Iran are typical examples of such a typology. Although many previous studies have investigated the performance of various types of wind catcher systems, studies based on a long-term real-life measurement can be rarely found. In this study a long-term whole year monitoring campaign on an existing full scale four sided wind catcher in Yazd was carried out in 2014–2015. Three prevailing wind directions were identified and the measured on-site wind speeds were used to estimate the wind induced natural ventilation potential of the tower. A shaft/tower airflow performance index was developed. The monitoring results were compared to the ASHRAE Standard 62:2001 ventilation rate requirement. Results show that the total ventilation rate of the wind tower surpasses the ASHRAE Standard requirements. Furthermore it shows that the shafts are exposed to the prevailing wind directions perform better. For more effective natural ventilation a wind tower with adaptable openings/shafts are proposed.     

METEOROLOGICAL EXPERIMENTS FOR AUTOMATED SATELLITES

Four satellites have been used in meteorology. They are TIROS, ESSA, Nimbus, and Applications Technology Satellite (ATS). The first three operate in the orbital altitudes of about 1000 to 1200 km while the fourth, ATS, is at geosynchronous altitude of 36,000 km. Cloud cover is being observed operationally from low orbit and experimentally from synchronous altitude. Wind velocity has been inferred from the frequent cloud cover pictures taken by ATS and satellite-balloon systems are being developed which will locate and track constant-density level balloons for determining wind flow. Spectrometers and radiometers operating in the electromagnetic spectral region from the ultraviolet to the microwave region are being developed to quantitatively measure temperature, water vapor, density, and wind profiles. These will furnish data for the development and testing of atmospheric models for numerical prediction. In addition, experiments are being developed to measure ozone and other constituents of the air, solar energy, surface conditions, heat balance and other atmospheric attributes which affect the structure and dynamics of the atmosphere.     

关于加强城市风环境规划研究的思考

城市风环境规划对于城市建设具有十分重要的意义,但在我国关注度还相对较低,为城市环境规划留有"隐患"。开展风环境规划研究,合理规划城市风环境,建立城市通风廊道,是城市规划的有益创新,也是践行习近平新时代中国特色社会主义思想的具体体现。本文梳理和总结了部分发达国家和地区城市风环境研究与技术发展状况,结合我国城市风环境规划研究和管理现状,从推动我国城市风环境规划的角度给出了若干建议。     

Improvement of fruit and vegetable waste anaerobic digestion performance and stability with co-substrates addition

The effect of fish waste (FW), abattoir wastewater (AW) and waste activated sludge (WAS) addition as co-substrates on the fruit and vegetable waste (FVW) anaerobic digestion performance was investigated under mesophilic conditions using four anaerobic sequencing batch reactors (ASBR) with the aim of finding the better co-substrate for the enhanced performance of co-digestion. The reactors were operated at an organic loading rate of 2.46–2.51 g volatile solids (VS) l⁻¹ d⁻¹, of which approximately 90% were from FVW, and a hydraulic retention time of 10 days. It was observed that AW and WAS additions with a ratio of 10% VS enhanced biogas yield by 51.5% and 43.8% and total volatile solids removal by 10% and 11.7%, respectively. However FW addition led to improvement of the process stability, as indicated by the low VFAs/Alkalinity ratio of 0.28, and permitted anaerobic digestion of FVW without chemical alkali addition. Despite a considerable decrease in the C/N ratio from 34.2 to 27.6, the addition of FW slightly improved the gas production yield (8.1%) compared to anaerobic digestion of FVW alone. A C/N ratio between 22 and 25 seemed to be better for anaerobic co-digestion of FVW with its co-substrates. The most significant factor for enhanced FVW digestion performance was the improved organic nitrogen content provided by the additional wastes. Consequently, the occurrence of an imbalance between the different groups of anaerobic bacteria which may take place in unstable anaerobic digestion of FVW could be prevented.     

Prescribed burning effects on summer elk forage availability in the subalpine zone, Banff National Park, Canada

The effects of prescribed burning on forage abundance and suitability for elk (Cervus elaphus) during the snow-free season was evaluated in east-central Banff National Park, Canada. Six coniferous forest and mixed shrub-herb plant communities (n=144 plots), and 5223ha of burned (n=131) vegetation <12 years old were sampled using a stratified semi-random design. Sampling units represented various combinations of vegetation, terrain conditions, and stand ages that were derived from digital biophysical data, with plant communities the basic unit of analysis. Burning coniferous forest stands reduced woody biomass, and increased herbaceous forage from 146 to 790 kg/ha. Increases commonly occurred in the percent cover of hairy wild rye (Leymus innovatus (Beal) Pigler) and fireweed (Chamerion angustifolium (L.) Holub.). The herbaceous components of mixed shrub-herb communities increased from 336-747 kg/ha to 517-1104 kg/ha in response to burning (P<0.025, Mann-Whitney U-test). Browse biomass (mostly Salix spp. and Betula nana L.) increased >or=220% (P相似文献   

Analysing the influence of different street vegetation on traffic-induced particle dispersion using microscale simulations

Urban vegetation can be viewed as compensation to the environmental drawbacks of urbanisation. However, its ecosystem function is not well-known and, for urban planning, vegetation is mainly considered as an element of urban design. This article argues that planning practice needs to re-examine the impact of vegetation cover in the urban fabric given our evaluation of vegetation's effects on air quality, including the dispersion of traffic-induced particles at street level. Using the three-dimensional microclimate model ENVI-met?, we evaluate these effects regarding the height-to-width ratio of streets flanked by buildings and the vertical and horizontal density of street vegetation. Our results reveal vegetation's effect on particle dispersion through its influence on street ventilation. In general, vegetation was found to reduce wind speed, causing inhibition of canyon ventilation and, consequently, an increase in particle concentrations. Vegetation was also found to reduce wind speed at crown-height and to disrupt the flow field in close vicinity to the canopy. With increasing height-to-width ratio of street canyons, wind speed reduction increases and the disturbance of the flow impacts across a canyon's entire width. We also found that the effect is more pronounced in configurations with poor ventilation, such as the low wind speed, perpendicular inflow direction, and in deep canyons cases.     

珠江三角洲一次探空过程风的垂直结构特征研究

应用2004 - 10月在珠江三角洲城市群(番禺)、珠江口沿岸(新垦)和乡村(清远)大气边界层观测的资料,对珠江三角洲大气边界层风的垂直结构特征进行了分析和对比.分析结果表明:受下垫面影响,城市群、乡村和珠江口沿岸的风垂直结构以及其日变化各有特点.城市热岛比较明显,系统风小时可以观测到热岛环流;珠江口沿岸夜间有明显的海...     

An inventory of trace element inputs to agricultural soils in China

It is important to understand the status and extent of soil contamination with trace elements to make sustainable management strategies for agricultural soils. The inputs of trace elements to agricultural soils via atmospheric deposition, livestock manures, fertilizers and agrochemicals, sewage irrigation and sewage sludge in China were analyzed and an annual inventory of trace element inputs was developed. The results showed that atmospheric deposition was responsible for 43–85% of the total As, Cr, Hg, Ni and Pb inputs, while livestock manures accounted for approximately 55%, 69% and 51% of the total Cd, Cu and Zn inputs, respectively. Among the elements concerned, Cd was a top priority in agricultural soils in China, with an average input rate of 0.004 mg/kg/yr in the plough layer (0–20 cm). Due to the spatial and temporal heterogeneity of the sources, the inventory as well as the environmental risks of trace elements in soils varies on a regional scale. For example, sewage sludge and fertilizers (mainly organic and phosphate-based inorganic fertilizers) can also be the predominant sources of trace elements where these materials were excessively applied. This work provides baseline information to develop policies to control and reduce toxic element inputs to and accumulation in agricultural soils.     

Dispersion of odour: a case study with a municipal solid waste landfill site in North London,United Kingdom

Municipal solid waste (MSW) landfills are a potential source of offensive odours that can create annoyance within communities. Dispersion modelling was used to quantify the potential odour strength causing an impact on the community around a particular MSW landfill site north of the London area in the United Kingdom. The case studies were completed with the short-term mode of COMPLEX-I, software developed by the US-EPA. The year 1998 was chosen as a source of baseline data. It was observed that by 2004, when the landfill will progress towards the west and a big band of the area towards the north would be partly/fully restored, the maximum contribution of the new sources giving higher odour concentrations would be in the southwesterly regions away from the landfill. Concentrations as high as 25.0 ou(E)/m(3) were observed with 3 min averaging time in the southwesterly areas as compared to concentrations of 20.0 ou(E)/m(3) at 10 min averaging times. However, the percentage frequency of such critical events occurring would be low. All other surrounding farms and small villages would be exposed to the concentration of 3.0 ou(E)/m(3) on certain occasions. In the year 2008, the majority of the filling fronts would be filled with wastes with no contributions from the active and operational cells. The maximum odour concentration around the landfill site for 1 h averaging time would be approximately 3 ou(E)/m(3) about 1.0 km north and 500 m west of the landfill site. For 3 min averaging time, the stretch of 5 ou(E)/m(3) band would be up to 2.5 km towards the north of the landfill site. It is argued that further analysis of the model calculations considering effects of wind direction, frequency of wind direction, stability of the atmosphere, selected odour threshold, integration time of the model, etc. would form a basis for calculating the separation distances of the landfill site from the surrounding community.     

渤海偏东风对北戴河区降水及温度影响统计分析

利用2001—2010年1～12月北戴河观测站气象资料,筛选出401个样本个例,应用常规统计学方法及天气学理论,按不同分级统计分析降雨(雪)前6～8 h风向、风速及转为海风时温度变化基本数据,计算不同分级相关系数值,得出海上偏东风与降水、温度半定量化估计值。并用临近4个观测站同步资料对比分析,偏东风动态变化对岸区强降水落区具有指示意义;北戴河至内陆延伸温度梯度估计值为:夏季平均值0.6℃/10 km,冬季0.3℃/10 km;为单站精细化预报方法研究及中尺度数值模式检验提供基本依据。     

Household organic waste composting using bins with different types of passive aeration

The objective of this study was to study the performances of six 200-L polyethylene bins, each with different design for passive aeration to organic wastes composting. Food scraps and dry leaves (1.6 kg) were added to each bin once a day until the bin was full. Temperatures at the middle portion were measured daily. The compost from each bin was taken once a week for 120 days for analysis of C, N, volatile solids, and a germination index once a week for 120 days. After 120 days, the compost sample from each bin was taken to determine the mass reduction, size distribution, CEC, N, P and K values. The results showed that the temperatures inside the bins were in the ranges of 24 °C-57 °C. The composts in all bins were found to be stable at around 56-91 days. The wastes decayed fastest in bins with lateral and vertical systems of natural ventilation. It took about two months to stabilize the organic wastes, with a 59-62% decrease of mass. The C/N ratio, CEC, N, P, and K values of the final composts were 14.8-16.0, 66-68 cmol/kg, and 1.26-1.50% N, 0.52-0.56% P₂O₅ and 1.66-1.92% K₂O, respectively.     

Potential for electricity savings by reducing potable water consumption in a city scale

Nowadays, it is very important that water and energy resources are used appropriately as this is a challenge to promote sustainable development. In some sectors, such as water and sewerage utilities, energy consumption depends on water consumption. The main objective of this work is to estimate the potential for electricity savings in a water and sewerage utility by reducing potable water consumption in the residential, commercial and public sectors in the city of Florianópolis, southern Brazil. These three sectors account for 98.9% of the total water consumption in the city. By using data related to energy consumption and costs that apply to the local water utility for water and sewage treatment, and also the potential for potable water savings over the three sectors, it is possible to estimate the potential for energy savings by reducing potable water consumption and sewage treatment. Potable water savings were estimated by using data available in the literature about water end-uses for different types of buildings located in Florianópolis. Three options were considered: installing dual-flush toilets, reusing greywater and using rainwater. The average potential for potable water savings were 30.0%, 53.4% and 60.3%, respectively, for the residential, commercial and public sectors. Thus, the average potable water savings amount to about 10,153,835 m³/year, and the electricity savings amount to 4.4 GW h/year, which would be enough to supply 1217 houses or flats in Florianópolis, with an average energy consumption of 300 kW h/month.