Removal of organic pollutants and nutrients from olive mill wastewater by a sand filter

The aim of this work was to examine the performance of a sand filter in treating modern olive mill (OMW) effluents after dilution with domestic wastewater on a one-to-one basis. The experimental pilot consisted of a column of opaque PVC, and the sand filter was filled with 50 cm of sand and 10 cm of gravel in the top and the bottom of the filter. The alimentation (4 cm/day) was done sequentially following a 1 day wet/3 days dry cycle. The OMW effluent was very acidic with a pH of 4.12, and had high concentrations of phenolic compounds (7.2 g/L) and total chemical oxygen demand (65 g/L). The percolation of the diluted OMW through the sand filters caused an increase in pH from 4.84 to 8.25 and a 90% removal of total suspended solids. The sand filter treatment also led to important reductions in organic matter (90% of total COD, 83% of dissolved COD and 92% of phenolic compounds) and nutrients (91% of Kjeldahl-nitrogen, 97% of ammonia-nitrogen, 99% of nitrate-nitrogen and 99% of phosphates). The flow rate became very low indicating clogging of the sand pores after 10 weeks. HPLC analysis of the diluted OMW before and after passage through the sand filter showed an important reduction in the toxic monomeric compounds after the treatment.     

Removal of mercury from aqueous solutions using activated carbon prepared from agricultural by-product/waste

Removal of mercury from aqueous solutions using activated carbon prepared from Ceiba pentandra hulls, Phaseolus aureus hulls and Cicer arietinum waste was investigated. The influence of various parameters such as effect of pH, contact time, initial metal ion concentration and adsorbent dose for the removal of mercury was studied using a batch process. The experiments demonstrated that the adsorption process corresponds to the pseudo-second-order-kinetic models and the equilibrium adsorption data fit the Freundlich isotherm model well. The prepared adsorbents ACCPH, ACPAH and ACCAW had removal capacities of 25.88 mg/g, 23.66 mg/g and 22.88 mg/g, respectively, at an initial Hg(II) concentration of 40 mg/L. The order of Hg(II) removal capacities of these three adsorbents was ACCPH > ACPAH > ACCAW. The adsorption behavior of the activated carbon is explained on the basis of its chemical nature. The feasibility of regeneration of spent activated carbon adsorbents for recovery of Hg(II) and reuse of the adsorbent was determined using HCl solution.     

Arsenic and chromium removal by mixed magnetite–maghemite nanoparticles and the effect of phosphate on removal

Adsorption of arsenic and chromium by mixed magnetite and maghemite nanoparticles from aqueous solution is a promising technology. In the present batch experimental study, a commercially grade nano-size ‘magnetite’, later identified in laboratory characterization to be mixed magnetite–maghemite nanoparticles, was used in the uptake of arsenic and chromium from different water samples. The intent was to identify or develop a practical method for future groundwater remediation. The results of the study showed 96–99% arsenic and chromium uptake under controlled pH conditions. The maximum arsenic adsorption occurred at pH 2 with values of 3.69 mg/g for arsenic(III) and 3.71 mg/g for arsenic(V) when the initial concentration was kept at 1.5 mg/L for both arsenic species, while chromium(VI) concentration was 2.4 mg/g at pH 2 with an initial chromium(VI) concentration of 1 mg/L. Thus magnetite–maghemite nanoparticles can readily adsorb arsenic and chromium in an acidic pH range. Redox potential and pH data helped to infer possible dominating species and oxidation states of arsenic and chromium in solution. The results also showed the limitation of arsenic and chromium uptake by the nano-size magnetite–maghemite mixture in the presence of a competing anion such as phosphate. At a fixed adsorbent concentration of 0.4 g/L, arsenic and chromium uptake decreased with increasing phosphate concentration. Nano-size magnetite–maghemite mixed particles adsorbed less than 50% arsenic from synthetic water containing more than 3 mg/L phosphate and 1.2 mg/L of initial arsenic concentration, and less than 50% chromium from synthetic water containing more than 5 mg/L phosphate and 1.0 mg/L of chromium(VI). In natural groundwater containing more than 5 mg/L phosphate and 1.13 mg/L of arsenic, less than 60% arsenic uptake was achieved. In this case, it is anticipated that an optimum design with magnetite–maghemite nanoparticles may achieve high arsenic uptake in field applications.     

Solar oxidation and removal of arsenic from water: An experimental study

Arsenic poses a significant threat to both human health and the environment. Arsenic removal through solar oxidation has been investigated in a batch process. Arsenic was artificially added to both deionized and tap water to conduct the experiments. Clean, colorless, transparent, Polyethylene Terephthalate (PET) bottles were used for Solar Oxidation and Removal of Arsenic (SORAS) experiments. Various parameters including concentration of arsenic, iron, and photo-catalyst were varied during the experiments. The maximum arsenic removal efficiency obtained was 94% and 88% for deionized water and tap water respectively when ferrous ammonium sulphate and lemon juice were used. Maximum efficiency of 88% and 82% was obtained for deionized and tap water respectively when locally available ferrous alum and glacial acetic acid were used. The change in volume of the photo-catalyst (lemon juice and glacial acetic acid) also did not affect the SORAS process significantly. Therefore, the recommended volume for the photo-catalyst was 1–2 ml/L. SORAS can very well be used for areas contaminated with arsenic having concentrations less than 100 μg/L.     

北京市垃圾填埋场地下水中砷、汞含量分析

生活垃圾的处置一直以填埋为主,垃圾填埋承载着巨大的环境压力,尤其是垃圾填埋产生的渗滤液会对地下水造成砷、汞污染。为了解北京市生活垃圾填埋场地下水砷、汞污染水平,在北京市5座生活垃圾填埋场布设采样点,采集36个地下水样品,采用氢化物发生-原子荧光法,分析了地下水砷、汞含量特征。结果表明,36个地下水样品砷浓度范围0.41~4.82μg/L,汞浓度范围0.024~0.121μg/L,北京市典型垃圾填埋场地下水样品不存在砷、汞污染问题。     

Anaerobic ammonium oxidation by Nitrosomonas spp. and anammox bacteria in a sequencing batch reactor

A sequencing batch reactor (SBR) was inoculated with mixed nitrifying bacteria from an anoxic tank at the conventional activated sludge wastewater treatment plant in Nongkhaem, Bangkok, Thailand. This enriched nitrifying culture was maintained under anaerobic conditions using ammonium (NH(4)(+)) as an electron donor and nitrite (NO(2)(-)) as an electron acceptor. Autotrophic ammonium oxidizing bacteria survived under these conditions. The enrichment period for anammox culture was over 100 days. Both ammonium and nitrite conversion rates were proportional to the biomass of ammonium oxidizing bacteria; rates were 0.08 g N/gV SS/d and 0.05 g N/g VSS/d for ammonium and nitrite, respectively, in a culture maintained for 3 months at 42 mg N/L ammonium. The nitrogen transformation rate at a ratio of NH(4)(+)-N to NO(2)(-)-N of 1:1.38 was faster, and effluent nitrogen levels were lower, than at ratios of 1:0.671, 1:2.18, and 1:3.05. Fluorescent in situ hybridization (FISH) was used to identify specific autotrophic ammonium oxidizing bacteria (Nitrosomonas spp., Candidatus Brocadia anammoxidans, and Candidatus Kuenenia stuttgartiensis). The ammonium oxidizing culture maintained at 42 mg N/L ammonium was enriched for Nitrosomonas spp. (30%) over Candidati B. anammoxidans and K. stuttgartiensis (2.1%) while the culture maintained at 210 mg N/L ammonium was dominated by Candidati B. anammoxidans and K. stuttgartiensis (85.6%). The specific nitrogen removal rate of anammox bacteria (0.6 g N/g anammox VSS/d) was significantly higher than that of ammonium oxidizing bacteria (0.4 g N/g Nitrosomonas VSS/d). Anammox bacteria removed up to 979 mg N/L/d of total nitrogen (ammonium:nitrite concentrations, 397:582 mg N/L). These results suggest significant promise of this approach for application to wastewater with high nitrogen but low carbon content, such as that found in Bangkok.     

硫磺回收装置脱硫废液处理的试验研究

采用将脱硫废液与炼油废水按比例混合之后对其进行处理的方法,通过批式试验,考查混合废液的BOD5/COD指标及其COD、NH3-N、S2-的去除率。筛选合适的混合液配比,分别对500︰1和800︰1的混合废液进行了模型试验,分析了COD去除效果。结果表明:800︰1的混合废液在10d之后,出水COD为134mg/L,达到了《污水综合排放标准》(GB8978—1996)二级标准要求。最终确定炼油废水与脱硫废液混合的合适比例应不低于800︰1。     

Changing effluent chemistry affect survival,growth and physiological function of <Emphasis Type="Italic">Acacia nilotica</Emphasis> seedlings in northwestern region of India

Recycling and conservation efforts for water are the need of the day because of the lack of new water sources and the ever-increasing demand for drinking water. Seedlings of Acacia nilotica L. were irrigated with: canal water (T₁, control); municipal effluent (T₂); textile effluent (T₃); steel effluent (T₄); textile + municipal effluent in 1:1 ratio (T₅); steel + municipal effluent in 1:2 ratio (T₆); steel + textile in 1:2 ratio (T₈) and steel + municipal + textile in 1:2:2 ratio (T₇) with views to observe effluents effect on the seedlings and its adaptability and to recommend safe disposal of these effluents. Seedlings in T₆, T₇ and T₈ showed 50% lesser height and collar diameter than those in control. Seedlings in T₂ attained greatest height, collar diameter, numbers of branches and produced 140 g dry biomass seedling⁻¹. Highest concentration of manganese (Mn), iron (Fe), copper (Cu) and zinc (Zn) and lowest concentration of nitrogen (N), phosphorus (P), potassium (K), calcium (Ca) and magnesium (Mg) in the seedlings of T₄, T₆, T₇ and T₈ resulted in nutritional imbalance, mineral toxicity and reduction in photosynthetic (Pn) and transpiration (E) rates and caused seedling mortality. Seedlings of T₃ had highest sodium concentration and low concentration of Ca, Mg and micronutrients resulting in nutritional imbalance, augmented chlorosis and reduced gas exchange and biomass by half as compared to control. Increased growth, Pn and E and biomass in seedlings of T₅ over T₃ and survival period in T₆, T₇ and T₈ seedlings suggested a beneficial effect of effluents mixing. Unscientific disposal should be avoided and toxic concentration of metal ions␣may be reduced for long-term application and harmless disposal of effluents in afforestation and urban development.     

Performance and modeling studies of rotating biological contactor for treatment of vegetable oil wastewater

This study focuses on a lab-scale rotating biological contactor (RBC) treating vegetable oil wastewater with high BOD and COD. The fabricated RBC was checked for efficiency in degrading polluted wastewater under different operating conditions. The maximum removal efficiencies for BOD and COD were 95.75% and 89%, respectively. This high removal percentage was obtained with 30% submergence of 10 discs rotating at 8 rpm. For the first time, bio-kinetic models were applied to the experimental results for vegetable oil wastewater. The best fit was obtained with the modified Stover-Kincannon and Grau model. The saturation constant (K_s) values were 1.872 and 3.024 g/L/d for BOD and COD, respectively, for the modified Stover-Kincannon and Grau model. For the Grau second-order model, the saturation constant was 1.416 and 3.744 g/L/d for BOD and COD, respectively. The predicted effluent BOD and COD values of the modified Stover–Kincannon model fitted almost exactly with the experimental values. This clearly predicts that this model can be best used to predict effluent BOD and COD concentration in a Rotating Biological contactor treating vegetable oil wastewater. The kinetic parameters determined in this study can be used to improve the design and operation of continuous mode RBC systems.     

微波消解-原子荧光光谱法同时测定土壤中痕量砷和汞

建立了微波消解—原子荧光光谱法同时测定土壤中痕量砷和汞的方法。通过对消解体系以及灯电流、载气流量、屏蔽气流量等仪器参数进行优化,确定了最佳实验条件。在优化的实验条件下,采用原子荧光光谱法同时测定砷和汞的检出限分别为0.02μg/L和0.01μg/L,线性范围分别为0～40μg/L和0～4μg/L,两元素的加标回收率在92%～102%之间,相对标准偏差砷为0.9%～3.1%,汞为1.5%～3.4%,完全适用于土壤环境样品的检测。     

Performance of a stratified sand filter in removal of chemical oxygen demand, total suspended solids and ammonia nitrogen from high-strength wastewaters

A stratified sand filter column, operated in recirculation mode and treating synthetic effluent resembling high-strength dairy wastewaters was studied over a 342-d duration. The aim of this paper was to examine the organic, total suspended solids (TSS) and nutrient removal rates of the sand filter, operated in recirculation mode, under incrementally increasing hydraulic and organic loading rates and to propose a field filter-sizing criterion. Best performance was obtained at a system hydraulic loading rate of 10 L m(-2) d(-1); a higher system hydraulic loading rate (of 13.4 L m(-2) d(-1)) caused surface ponding. The system hydraulic loading rate of 10 L m(-2) d(-1) gave a filter chemical oxygen demand (COD), TSS, and total kjeldahl nitrogen (TKN) loading rate of 14, 3.7, and 2.1 g m(-2) d(-1), respectively, and produced consistent COD and TSS removals of greater than 99%, and an effluent NO(3)-N concentration of 42 mg L(-1) (accounting for an 86% reduction in total nitrogen (Tot-N)). As the proportional surface area requirement for the sand filter described in this study is less than the recommended surface area requirement of a free-water surface (FWS) wetland treating an effluent of similar quality, it could provide an economic and sustainable alternative to conventional wetland treatment.     

Role of organic matter in microbial transport during irrigation with sewage effluent

Reduction of migration of fecal coliforms (FC) and streptococci (FS) by limiting the leaching in effluent-irrigated soil was tested in lysimeters packed with quartz sand without or with added biosolids compost or with one of two clayey soils. The 200-L, 70-cm-deep lysimeters were either planted with a Eucalyptus camaldulensis or an Oroblanco citrus tree (in the sand only), or not planted. The Eucalyptus was irrigated with oxidation pond effluent (OPE) and the Oroblanco with mechanical-biological treatment plant effluent (MBTPE). The leaching fraction (LF) ranged from 0.2 to about 1.0, and the residence time (RT) from under 1 to 40 d. The Eucalyptus was also tested under intermittent leaching (RT 11-20 d) and deficit irrigation (without leaching for about 6 mo) regimes. Under MBTPE irrigation there was little or no leaching of FC and FS. Under OPE irrigation at LF 1 without a Eucalyptus there was little or no bacterial leaching at irrigation rates below 40 L d(-1) per lysimeter (RT > or = 0.8 d). Bacterial counts in the leachate were substantial in the presence of a Eucalyptus tree under LF 0.2 and intermittent leaching regimes, and when sand-packed unplanted lysimeters received OPE effluent at >45 L d(-1). Bacterial recovery peaked at LF 0.2, at up to 45% of the input level. At LF 1 (RT 0.6-2.8 d) and with intermittent leaching the recoveries were minute. Bacterial counts in the washout from the deficit-irrigated lysimeters were typical of nonpolluted soils. The bacterial concentration and recovery patterns in the leachate mostly matched the organic carbon (OC) load in the irrigation water, and its concentration and bioavailablity in the leachate. We related the leaching patterns of the fecal bacteria to their relative reproduction and die-off rates, and to the dependence of their regrowth on available carbon sources.     

Phosphorus and other soil components in a dairy effluent sprayfield within the central Florida Ridge

There is concern that P from dairy effluent sprayfields will leach into groundwater beneath Suwannee River basins in northern Florida. Our purpose was to describe the effects of dairy effluent irrigation on the movement of soil P and other nutrients within the upper soil profile of a sprayfield over three 12-mo cycles (April 1998-March 2001). Effluent P rates of 70, 110, and 165 kg ha(-1) cycle(-1) were applied to forages that were grown year-round. The soil is a deep, excessively drained sand (thermic, uncoated Typic Quartzipsamment). Mean P concentration in soil water below the rooting zone (152-cm depth) was < or = 0.1 mg L(-1) during 11 3-mo periods. Mehlich-1-extractable (M1) P, Al, and Ca in the topsoil increased over time but did not change in subsoil depths of 25 to 51, 51 to 71, 71 to 97, and 97 to 122 cm. Topsoil Ca increased as effluent rate increased. High Ca levels were found in dairy effluent (avg.: 305 mg L(-1)) and supplemental irrigation water (avg.: 145 mg L(-1)) which likely played a role in retaining P in the topsoil. An effect of effluent rate on P and Al concentrations in the topsoil was not detected, probably due to large and variable quantities present at project initiation. The P retention capacity (i.e., Al plus Fe) increased in the topsoil because Al increased. Dairy effluent contained Al (avg.: 31 mg L(-1)). Phosphorus saturation ratio (PSR) increased over time in the topsoil but not in subsoil layers. Regardless of effluent rate, the P retention capacity and PSR of subsoil, which contained 119 to 229 mg kg(-1) of Al, should be taken into account when assessing the risk of P moving below the rooting zone of most forage crops.     

Characterization of pollutants in Florida street sweepings for management and reuse

Disposal and beneficial-use options for street sweeping residuals collected as part of routine roadway maintenance activities in Florida, USA, were assessed by characterizing approximately 200 samples collected from 20 municipalities. Total concentrations (mg/kg or μg/kg) and leachable concentrations (mg/L or μg/L) of 11 metals and a number of organic pollutant groups (volatile organics, semi-volatile organics, pesticides, herbicides, carbamates) in the samples were measured. The synthetic precipitation leaching procedure (SPLP) was performed to evaluate the leachability of the pollutants. From the total metal analysis, several metals (e.g., arsenic, barium, chromium, copper, nickel, lead, and zinc) were commonly found above their detection limits. Zinc was found to have the highest mean concentration of all metals measured (46.7 mg/kg), followed by copper (10.7 mg/kg) and barium (10.5 mg/kg). The metal with the smallest mean concentration was arsenic (0.48 mg/kg). A small fraction of the total arsenic, barium, lead, and zinc leached in some samples using the SPLP; leached concentrations were relatively low. A few organic compounds (e.g., 4,4′-DDT, endrin, and endosulfan II) were detected in a limited number of samples. When the total and leaching results were compared to risk-based Florida soil cleanup target levels and groundwater cleanup target levels, the street sweepings were not found to pose a significant human-health risk via direct exposure or groundwater contamination.     

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions.The influence of impregnation ratio (ZnCl₂/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m²/g) and micropore volume (0.772 cm³/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio.Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 °C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others.Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl₂ is a suitable activating agent for the preparation of high-porosity carbons.     

Sorption of arsenic from soil-washing leachate by surfactant-modified zeolite

Post-treatment of leachate from soil-washing remedial actions may be necessary depending on the amounts of dissolved contaminants present. Uptake of arsenic species by surfactant-modified zeolite (SMZ) from a synthetic soil leachate (pH of approximately 12 [NaOH]) was measured as a test of SMZ as a post-treatment sorbent. Batch sorption isotherms were prepared using leachate to SMZ ratios from 40:1 to 4:1, and temperatures of 25 and 15 degrees C. Equilibrium levels of dissolved and total solution arsenic were similar. At each temperature, sorption appeared to reach a plateau or maximum, then decreased at the highest solution concentration, corresponding to the lowest amount of zeolite added (2.5 g). A maximum sorption value of 72.0 mmol of arsenic per kg of SMZ (5400 mg/kg) was observed at 25 degrees C, and 42.1 mmol/kg (3150 mg/kg) at 15 degrees C. Total arsenic recoveries varied from 74 to 125%. Surfactant-modified zeolite removed up to 97% of dissolved organic carbon and decolorized the leachate solutions. Excluding the points for the highest arsenic to SMZ ratio, the sorption isotherms were well described by the linearized form of the Langmuir equation, with coefficients of determination greater than 0.90 at both temperatures. Sorption of arsenic by SMZ is attributed to anion exchange with counterions on the surfactant head groups, and/or partitioning of organic carbon-complexed arsenic into the surfactant bilayer.     

Studies on solvent extraction of iron(III) as a step for conversion of a waste effluent to a value added product

Solvent extraction of iron(III) from actual sulphate waste pickle liquor was investigated using trialkylphosphine oxide diluted with kerosene. The waste pickle liquor was procured from a local company which deals with the manufacturing of pipes and tubes made of iron and steel. Various parameters were studied to optimise a suitable condition for the maximum extraction of iron. The composition of the aqueous feed used in the experiment was 60.88 g/L Fe(III), 53 g/L acid with traces of Cu, Ni and Co. An ambient extraction at 30 °C yielded acceptable kinetics and loading efficiency for 40% trialkylphosphine oxide with a saturated loading capacity of 51.85 g/L in four contacts at O/A ratio of 1/1 in a multiple contact mode. Iron from the loaded organic was stripped using various strippants such as distilled water, H₂SO₄ and oxalic acid. Since only 32% of loaded Fe could be stripped with 2 M H₂SO₄ in five contacts, further stripping was done with 5% oxalic acid which showed a very promising result. It was found that almost 100% of Fe(III) could be stripped out with 5% oxalic acid at O/A of 1/1 in five contacts.     

Recirculating sand filters for treatment of synthetic dairy parlor washings

Land-spreading and spray irrigation are the most widely used practices for the disposal of dairy wastewaters in Ireland but in some cases there can be problems due to contamination of surface and ground water. The use of intermittent sand filtration has been suggested as an alternative treatment process. However, a single pass through a sand filter limits denitrification because of the absence of reducing conditions following nitrification and the lack of an available carbon source. This leads to poor total nitrogen (TN) reduction and an effluent that is high in nitrate nitrogen (NO3-N). This paper follows a previous paper in which two instrumented stratified sand filter columns (0.9 and 0.425 m deep, and both 0.3 m in diameter) were intermittently loaded with synthetic dairy parlor washings at a number of hydraulic loading rates, leading to a TN reduction of 27 to 41%. In the present study, under a chemical oxygen demand (COD) of 23.4 g m(-2) d(-1), the TN was reduced by 83.2% when three-quarters of the sand filter effluent was recirculated through an anoxic zone. This produced an effluent NO3-N concentration of 60 mg L(-1). With recirculation, the improvement in the removal of organic matter and ammonia N (NH4-N) is minimal. Recirculating sand filters appear to offer a mechanically simple and effective method for the removal of nitrogen from dairy parlor effluents and are a significant improvement over a single-pass sand filter.     

Arsenic levels in the marine ecosystem off the Kuwait coast, Arabian Gulf

Arsenic levels in seawater, microplankton (diatoms and dinoflagellates), shrimp (Penaeus semisulcatus), mollusc (Cerithium scabridum) and five types of fish (Maid, Nakroor, Nuwaiby, Suboor and Sheim) in five sampling stations (I–V) off the Kuwait coast were determined during the years 1995 to 1999. The maximum mean concentration of arsenic was observed in the order; the five fish (0.50–0.78 g g^–1)> mollusc (0.26 g g^–1)> shrimp (0.23 g g^–1)> particulate matter (0.03 g g^–1)> water and phytoplankton (0.02 g g^–1) from all the sites of the Kuwait coast. Station II possessed the maximum arsenic levels. In comparison with the arsenic levels in other parts of the globe, low arsenic levels were observed in most of the marine organisms off the Kuwait Coast. However, an increasing trend in arsenic concentrations was anticipated due to rapid local industrialization and on account of recent spills of arsenic compounds.