CO2 storage and enhanced coalbed methane recovery: Reservoir characterization and fluid flow simulations of the Big George coal,Powder River Basin,Wyoming, USA

Coalbeds are an attractive geological environment for storage of carbon dioxide (CO₂) because CO₂ is retained in the coal as an adsorbed phase and the cost of injection can be offset by enhanced coalbed methane (ECBM) production. This paper presents the findings of a CO₂ storage feasibility study on coalbeds in the Wyodak-Anderson coal zone of the Powder River Basin, Wyoming, USA, using reservoir characterization and fluid flow simulations. A 3D numerical model of the Big George coal was constructed using geostatistical techniques, with values of cleat and matrix permeability and porosity constrained through history-matching of production data from coalbed methane (CBM) wells in the field area.Following history-matching, several ECBM and CO₂ storage scenarios were investigated: shrinkage and swelling of the coal was either allowed or disallowed, a horizontal hydraulic fracture was either placed at the injection well or removed from the model, the number of model layers was varied between 1 and 24, and the permeability and porosity fields were constructed to be either homogeneous or heterogeneous in accordance with geostatistical models of regional variability. All simulations assumed that the injected gas was 100% CO₂ and that the coalbed was overlain by an impermeable caprock. Depending on the scenario, the simulations predicted that after 13 years of CO₂ injection, the cumulative methane production would be enhanced by a factor of 1.5–5. Including coal matrix shrinkage and swelling in the model predicted swelling near the injection well, which resulted in a slight reduction (10%) in injection rate. However, including a horizontal hydraulic fracture in the model at the base of the injection well helped mitigate the negative effect of swelling on injection rate. It was also found that six model layers were needed to have sufficient resolution in the vertical direction to account for the buoyancy effects between the gas and resident water, and that capturing the heterogeneous nature of the coal permeability and porosity fields predicted lower estimates of the storage capacity of the Wyodak-Anderson coal zone.After noting that gravity and buoyancy were the major driving forces behind gas flow within the Big George coal, several leakage scenarios were also investigated, in an effort to better understand the interplay between diffusion and flow properties on the transport and storage of CO₂. The modeling predicted that the upward migration of gas due to the buoyancy effect was faster than the diffusion of CO₂ and therefore the gas rapidly rose to the top of the coalbed and migrated into overlying strata when an impermeable caprock was not included in the model.     

Comparison of adsorption models in reservoir simulation of enhanced coalbed methane recovery and CO2 sequestration in coal

Coalbed methane is an important resource of energy. Meanwhile CO₂ sequestration in coal is a potential management option for greenhouse gas emissions. An attractive aspect to this process is that CO₂ is adsorbed to the coal, reducing the risk of CO₂ migration to the surface. Another aspect to this is that the injected CO₂ could displace adsorbed methane leading to enhanced coalbed methane recovery. Therefore, in order to understand gas migration within the reservoir, mixed-gas adsorption models are required. Moreover, coal reservoir permeability will be significantly affected by adsorption-induced coal swelling during CO₂ injection. Coal swelling is directly related to reservoir pressure and gas content which is calculated by adsorption models in reservoir simulation. Various models have been studied to describe the pure- and mixed-gas adsorption on coal. Nevertheless, only the Langmuir and Extended Langmuir models are usually applied in coal reservoir simulations. This paper presents simulation work using several approaches to representing gas adsorption, implemented into the coal seam gas reservoir simulator SIMED II. The adsorption models are the Extended Langmuir model (ELM), the Ideal Adsorbed Solution (IAS) model and the Two-Dimensional Equation of State (2D EOS). The simulations based on one Australian and one American coal sample demonstrated that (1) the Ideal Adsorbed Solution model, in conjunction with Langmuir model as single-component isotherm, shows similar simulation results as the ELM for both coals, with the IAS model representing the experimental adsorption data more accurately than the ELM for one coal and identically with the ELM for the other coal; (2) simulation results using the 2D EOS, however, are significantly different to the ELM or IAS model for both coal samples. The magnitude of the difference is also dependent on coal swelling and the well operating conditions, such as injection pressure.     

Enhanced coalbed methane and CO2 storage in anthracitic coals—Micro-pilot test at South Qinshui,Shanxi, China

This paper describes the results of a single well micro-pilot test performed at an existing well in the anthracitic coals of the South Qinshui basin, Shanxi Province, China. A set of reservoir parameters was obtained from the micro-pilot test. The field data was successfully history matched using a tuned reservoir model which accounted for changes in permeability due to swelling and pressure change. Prediction of initial performance showed significant production enhancement of coalbed methane while simultaneously storing the CO₂. The calibrated reservoir model was used to design a multi-well pilot at the site to validate the performance prediction. The design is now completed. The recommendation is to proceed to the next stage of multi-well pilot testing and to demonstrate the enhanced coalbed methane (ECBM) technology.     

Effect of the effective stress coefficient and sorption-induced strain on the evolution of coal permeability: Experimental observations

Permeability is one of the most important parameters for CO₂ injection in coal to enhance coalbed methane recovery. Laboratory characterization of coal permeability provides useful information for in situ permeability behavior of coal seams when adsorbing gases such as CO₂ are injected. In this study, a series of experiments have been conducted for coal samples using both non-adsorbing and adsorbing gases at various confining stresses and pore pressures. Our observations have showed that even under controlled stress conditions, coal permeability decreases with respect to pore pressure during the injection of adsorbing gases. In order to find out the causes of permeability decrease for adsorbing gases, a non-adsorbing gas (helium) is used to determine the effective stress coefficient. In these experiments using helium, the impact of gas sorption can be neglected and any permeability reduction is considered as due to the variation in the effective stress, which is controlled by the effective stress coefficient. The results show that the effective stress coefficient is pore pressure dependent and less than unity for the coal samples studied. The permeability reduction from helium experiments is then used to calibrate the subsequent flow-through experiments using adsorbing gases, CH₄ and CO₂. Through this calibration, the sole effect of sorption-induced strain on permeability change is obtained for these adsorbing gas flow-through experiments. In this paper, experimental results and analyses are reported including how the impact of effective stress coefficient is separated from that of the sorption-induced strain on the evolution of coal permeability.     

Evaluating the impact of fractures on the performance of the In Salah CO2 storage site

The In Salah Gas Joint Venture CO₂ storage project has been in operation in Algeria since 2004 and is currently the world's largest onshore CO₂ storage project. CO₂ is injected into the saline aquifer of a gas reservoir several kilometres away from the gas producers. Current focus in the project is on implementing a comprehensive monitoring strategy and modelling the injection behaviour in order to ensure and verify safe long-term storage. A key part of this effort is the understanding of the processes involved in CO₂ migration within relatively low-permeability sandstones and shales influenced by fractures and faults. We summarise our current understanding of the fault and fracture pattern at this site and show preliminary forecasts of the system performance using discrete fracture models and fluid flow simulations. Despite evidence of fractures at the reservoir/aquifer level, the thick mudstone caprock sequence is expected to provide an effective flow and mechanical seal for the storage system; however, quantification of the effects of fracture flow is essential to the site verification.     

Investigations on CO2 storage capacity in saline aquifers—Part 2: Estimation of storage capacity coefficients

Many studies on geological carbon dioxide (CO₂) storage capacity neglect the influence of complex coupled processes which occur during and after the injection of CO₂. Storage capacity is often overestimated since parts of the reservoirs cannot be reached by the CO₂ plume due to gravity segregation and are thus not accessible for storage. This work investigates the effect of reservoir parameters like depth, temperature, absolute and relative permeability, and capillary pressure on the processes during CO₂ injection and thus on estimates of effective storage capacity. The applied statistical characteristics of parameters are based on a large reservoir parameter database. Different measured relative permeability relations are considered. The methodology of estimating storage capacity is discussed. Using numerical 1D and 3D experiments, detailed time-dependent storage capacity estimates are derived. With respect to the concept developed in this work, it is possible to estimate effective CO₂ storage capacity in saline aquifers. It is shown that effective CO₂ mass stored in the reservoir varies by a factor of 20 for the reservoir setups considered. A high influence of the relative permeability relation on storage capacity is shown.     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.     

Corrective measures based on pressure control strategies for CO2 geological storage in deep aquifers

A prerequisite to the wide deployment at an industrial scale of CO₂ geological storage is demonstrating that potential risks can be efficiently managed. Corrective measures in case of significant irregularities, such as CO₂ leakage, are hence required as advocated by the recent European directive on Carbon Capture and Storage operations. In this regard, the objective of the present paper is to investigate four different corrective measures aiming at controlling the overpressure induced by the injection operations in the reservoir: stopping the CO₂ injection and relying on the natural pressure recovery in the reservoir; extracting the stored CO₂ at the injection well; extracting brine at a distant well while stopping the CO₂ injection, and extracting at a distant well without stopping the CO₂ injection. The efficiency of the measures is assessed using multi-phase fluid flow numerical simulations. The application case is the deep carbonate aquifer of the Dogger geological unit in the Paris Basin. A comparative study between the four corrective measures is then carried using a cost-benefit approach. Results show that an efficient overpressure reduction can be achieved by simply shutting-in the well. The overpressure reduction can be significantly accelerated by means of fluid extraction but the adverse consequences are the associated higher costs of the intervention operations.     

CO2 storage capacity estimation: Methodology and gaps

Implementation of CO₂ capture and geological storage (CCGS) technology at the scale needed to achieve a significant and meaningful reduction in CO₂ emissions requires knowledge of the available CO₂ storage capacity. CO₂ storage capacity assessments may be conducted at various scales—in decreasing order of size and increasing order of resolution: country, basin, regional, local and site-specific. Estimation of the CO₂ storage capacity in depleted oil and gas reservoirs is straightforward and is based on recoverable reserves, reservoir properties and in situ CO₂ characteristics. In the case of CO₂-EOR, the CO₂ storage capacity can be roughly evaluated on the basis of worldwide field experience or more accurately through numerical simulations. Determination of the theoretical CO₂ storage capacity in coal beds is based on coal thickness and CO₂ adsorption isotherms, and recovery and completion factors. Evaluation of the CO₂ storage capacity in deep saline aquifers is very complex because four trapping mechanisms that act at different rates are involved and, at times, all mechanisms may be operating simultaneously. The level of detail and resolution required in the data make reliable and accurate estimation of CO₂ storage capacity in deep saline aquifers practical only at the local and site-specific scales. This paper follows a previous one on issues and development of standards for CO₂ storage capacity estimation, and provides a clear set of definitions and methodologies for the assessment of CO₂ storage capacity in geological media. Notwithstanding the defined methodologies suggested for estimating CO₂ storage capacity, major challenges lie ahead because of lack of data, particularly for coal beds and deep saline aquifers, lack of knowledge about the coefficients that reduce storage capacity from theoretical to effective and to practical, and lack of knowledge about the interplay between various trapping mechanisms at work in deep saline aquifers.     

Intermediate storage of carbon dioxide in geological formations: A technical perspective

Enhanced oil recovery (EOR) through CO₂ flooding has been practiced on a commercial basis for the last 35 years and continues today at several sites, currently injecting in total over 30 million tons of CO₂ annually. This practice is currently exclusively for economic gain, but can potentially contribute to the reduction of emissions of greenhouse gases provided it is implemented on a large scale. Optimal operations in distributing CO₂ to CO₂-EOR or enhanced gas recovery (EGR) projects (referred to here collectively as CO₂-EHR) on a large scale and long time span imply that intermediate storage of CO₂ in geological formations may be a key component. Intermediate storage is defined as the storage of CO₂ in geological media for a limited time span such that the CO₂ can be sufficiently reproduced for later use in CO₂-EHR. This paper investigates the technical aspects, key individual parameters and possibilities of intermediate storage of CO₂ in geological formations aiming at large scale implementation of carbon dioxide capture and storage (CCS) for deep emission reduction. The main parameters are thus the depth of injection and density, CO₂ flow and transport processes, storage mechanisms, reservoir heterogeneity, the presence of impurities, the type of the reservoirs and the duration of intermediate storage. Structural traps with no flow of formation water combined with proper injection planning such as gas-phase injection favour intermediate storage in deep saline aquifers. In depleted oil and gas fields, high permeability, homogeneous reservoirs with structural traps (e.g. anticlinal structures) are good candidates for intermediate CO₂ storage. Intuitively, depleted natural gas reservoirs can be potential candidates for intermediate storage of carbon dioxide due to similarity in storage characteristics.     

Assessing the economic feasibility of regional deep saline aquifer CO2 injection and storage: A geomechanics-based workflow applied to the Rose Run sandstone in Eastern Ohio, USA

Typical top-down regional assessments of CO₂ storage feasibility are sufficient for determining the maximum volumetric capacity of deep saline aquifers. However, they do not reflect the regional economic feasibility of storage. This is controlled, in part, by the number and type of injection wells that are necessary to achieve regional CO₂ storage goals. In contrast, the geomechanics-based assessment workflow that we present in this paper follows a bottom-up approach for evaluating regional deep saline aquifer CO₂ storage feasibility. The CO₂ storage capacity of an aquifer is a function of its porous volume as well as its CO₂ injectivity. For a saline aquifer to be considered feasible in this assessment it must be able to store a specified amount of CO₂ at a reasonable cost per ton of CO₂. The proposed assessment workflow has seven steps that include (1) defining the storage project and goals, (2) characterizing the geology and developing a geomechanical model of the aquifer, (3) constructing 3D aquifer models, (4) simulating CO₂ injection, (5,6) evaluating CO₂ injection and storage feasibility (with and without injection well stimulation), and (7) determining whether it is economically feasible to proceed with the storage project. The workflow was applied to a case study of the Rose Run sandstone aquifer in the Eastern Ohio River Valley, USA. We found that it is feasible in this region to inject 113 Mt CO₂/year for 30 years at an associated well cost of less than US $1.31/t CO₂, but only if injectivity enhancement techniques such as hydraulic fracturing and injection induced micro-seismicity are implemented.     

A method for quick assessment of CO2 storage capacity in closed and semi-closed saline formations

Saline aquifers of high permeability bounded by overlying/underlying seals may be surrounded laterally by low-permeability zones, possibly caused by natural heterogeneity and/or faulting. Carbon dioxide (CO₂) injection into and storage in such “closed” systems with impervious seals, or “semi-closed” systems with non-ideal (low permeability) seals, is different from that in “open” systems, from which the displaced brine can easily escape laterally. In closed or semi-closed systems, the pressure buildup caused by continuous industrial-scale CO₂ injection may have a limiting effect on CO₂ storage capacity, because geomechanical damage caused by overpressure needs to be avoided. In this research, a simple analytical method was developed for the quick assessment of the CO₂ storage capacity in such closed and semi-closed systems. This quick-assessment method is based on the fact that native brine (of an equivalent volume) displaced by the cumulative injected CO₂ occupies additional pore volume within the storage formation and the seals, provided by pore and brine compressibility in response to pressure buildup. With non-ideal seals, brine may also leak through the seals into overlying/underlying formations. The quick-assessment method calculates these brine displacement contributions in response to an estimated average pressure buildup in the storage reservoir. The CO₂ storage capacity and the transient domain-averaged pressure buildup estimated through the quick-assessment method were compared with the “true” values obtained using detailed numerical simulations of CO₂ and brine transport in a two-dimensional radial system. The good agreement indicates that the proposed method can produce reasonable approximations for storage–formation–seal systems of various geometric and hydrogeological properties.     

Basin-scale hydrogeologic impacts of CO2 storage: Capacity and regulatory implications

Industrial-scale injection of CO₂ into saline formations in sedimentary basins will cause large-scale fluid pressurization and migration of native brines, which may affect valuable groundwater resources overlying the deep sequestration aquifers. In this paper, we discuss how such basin-scale hydrogeologic impacts (1) may reduce current storage capacity estimates, and (2) can affect regulation of CO₂ storage projects. Our assessment arises from a hypothetical future carbon sequestration scenario in the Illinois Basin, which involves twenty individual CO₂ storage projects (sites) in a core injection area most suitable for long-term storage. Each project is assumed to inject five million tonnes of CO₂ per year for 50 years. A regional-scale three-dimensional simulation model was developed for the Illinois Basin that captures both the local-scale CO₂–brine flow processes and the large-scale groundwater flow patterns in response to CO₂ storage. The far-field pressure buildup predicted for this selected sequestration scenario support recent studies in that environmental concerns related to near- and far-field pressure buildup may be a limiting factor on CO₂ storage capacity. In other words, estimates of storage capacity, if solely based on the effective pore volume available for safe trapping of CO₂, may have to be revised based on assessments of pressure perturbations and their potential impacts on caprock integrity and groundwater resources. Our results suggest that (1) the area that needs to be characterized in a permitting process may comprise a very large region within the basin if reservoir pressurization is considered, and (2) permits cannot be granted on a single-site basis alone because the near- and far-field hydrogeologic response may be affected by interference between individual storage sites. We also discuss some of the challenges in making reliable predictions of large-scale hydrogeologic impacts related to CO₂ sequestration projects.     

Life cycle modelling of fossil fuel power generation with post-combustion CO2 capture

Due to its compatibility with the current energy infrastructures and the potential to reduce CO₂ emissions significantly, CO₂ capture and geological storage is recognised as one of the main options in the portfolio of greenhouse gas mitigation technologies being developed worldwide. The CO₂ capture technologies offer a number of alternatives, which involve different energy consumption rates and subsequent environmental impacts. While the main objective of this technology is to minimise the atmospheric greenhouse gas emissions, it is also important to ensure that CO₂ capture and storage does not aggravate other environmental concerns. This requires a holistic and system-wide environmental assessment rather than focusing on the greenhouse gases only. Life Cycle Assessment meets this criteria as it not only tracks energy and non-energy-related greenhouse gas releases but also tracks various other environmental releases, such as solid wastes, toxic substances and common air pollutants, as well as the consumption of other resources, such as water, minerals and land use. This paper presents the principles of the CO₂ capture and storage LCA model developed at Imperial College and uses the pulverised coal post-combustion capture example to demonstrate the methodology in detail. At first, the LCA models developed for the coal combustion system and the chemical absorption CO₂ capture system are presented together with examples of relevant model applications. Next, the two models are applied to a plant with post-combustion CO₂ capture, in order to compare the life cycle environmental performance of systems with and without CO₂ capture. The LCA results for the alternative post-combustion CO₂ capture methods (including MEA, K⁺/PZ, and KS-1) have shown that, compared to plants without capture, the alternative CO₂ capture methods can achieve approximately 80% reduction in global warming potential without a significant increase in other life cycle impact categories. The results have also shown that, of all the solvent options modelled, KS-1 performed the best in most impact categories.     

The impact of heterogeneity on the distribution of CO2: Numerical simulation of CO2 storage at Ketzin

Numerical modelling of multiphase flow is an essential tool to ensure the viability of long-term and safe CO₂ storage in geological formations. Uncertainties arising from the heterogeneity of the formation and lack of knowledge of formation properties need to be assessed in order to create a model that can reproduce the data available from monitoring. In this study, we investigated the impact of unknown spatial variability in the petrophysical properties within a sandy channel facies of a fluviatile storage formation using stochastic methods in a Monte Carlo approach. The stochastic method has been applied to the Ketzin test site (CO₂SINK), and demonstrates that the deterministic homogeneous model satisfactorily predicts the first CO₂ arrival time at the Ketzin site. The equivalent permeability was adjusted to the injection pressure and is in good agreement with the hydraulic test. It has been shown that with increasing small-scale heterogeneity, the sharpness of the CO₂ front decreases and a greater volume of the reservoir is affected, which is also seen in an increased amount of dissolved CO₂. Increased anisotropy creates fingering effects, which result in higher probabilities for earlier arrival times. Generally, injectivity decreases with increasing heterogeneity.     

3D geomechanical modelling for CO2 geologic storage in the Dogger carbonates of the Paris Basin

CO₂ injection into a depleted hydrocarbon field or aquifer may give rise to a variety of coupled physical and chemical processes. During CO₂ injection, the increase in pore pressure can induce reservoir expansion. As a result the in situ stress field may change in and around the reservoir. The geomechanical behaviour induced by oil production followed by CO₂ injections into an oil field reservoir in the Paris Basin has been numerically modelled. This paper deals with an evaluation of the induced deformations and in situ stress changes, and their potential effects on faults, using a 3D geomechanical model. The geomechanical analysis of the reservoir–caprock system was carried out as a feasibility study using pressure information in a “one way” coupling, where pressures issued from reservoir simulations were integrated as input for a geomechanical model. The results show that under specific assumptions the mechanical effects of CO₂ injection do not affect the mechanical stability of the reservoir–caprock system. The ground vertical movement at the surface ranges from ?2 mm during oil production to +2.5 mm during CO₂ injection. Furthermore, the changes in in situ stresses predicted under specific assumptions by geomechanical modelling are not significant enough to jeopardize the mechanical stability of the reservoir and caprock. The stress changes issued from the 3D geomechanical modelling are also combined with a Mohr–Coulomb analysis to determine the fault slip tendency. By integrating the stress changes issued from the geomechanical modelling into the fault stability analysis, the critical pore pressure for fault reactivation is higher than calculated for the fault stability analysis considering constant horizontal stresses.     

Carbon dioxide storage capacity in uneconomic coal beds in Alberta,Canada: Methodology,potential and site identification

Methodology is presented for a first-order regional-scale estimation of CO₂ storage capacity in coals under sub-critical conditions, which is subsequently applied to Cretaceous-Tertiary coal beds in Alberta, Canada. Regions suitable for CO₂ storage have been defined on the basis of groundwater depth and CO₂ phase at in situ conditions. The theoretical CO₂ storage capacity was estimated on the basis of CO₂ adsorption isotherms measured on coal samples, and it varies between ∼20 kt CO₂/km² and 1260 kt CO₂/km², for a total of approximately 20 Gt CO₂. This represents the theoretical storage capacity limit that would be attained if there would be no other gases present in the coals or they would be 100% replaced by CO₂, and if all the coals will be accessed by CO₂. A recovery factor of less than 100% and a completion factor less than 50% reduce the theoretical storage capacity to an effective storage capacity of only 6.4 Gt CO₂. Not all the effective CO₂ storage capacity will be utilized because it is uneconomic to build the necessary infrastructure for areas with low storage capacity per unit surface. Assuming that the economic threshold to develop the necessary infrastructure is 200 kt CO₂/km², then the CO₂ storage capacity in coal beds in Alberta is greatly reduced further to a practical capacity of only ∼800 Mt CO₂.     

Analytical solution for estimating storage efficiency of geologic sequestration of CO2

During injection of carbon dioxide (CO₂) into deep saline aquifers, the available pore volume of the aquifer may be used inefficiently, thereby decreasing the effective capacity of the repository for CO₂ storage. Storage efficiency is the fraction of the available pore space that is utilized for CO₂ storage, or, in other words, it is the ratio between the volume of stored CO₂ and the maximum available pore volume. In this note, we derive and present simple analytical expressions for estimating CO₂ storage efficiency under the scenario of a constant-rate injection of CO₂ into a confined, homogeneous, isotropic, saline aquifer. The expressions for storage efficiency are derived from models developed previously by other researchers describing the shape of the CO₂-brine interface. The storage efficiency of CO₂ is found to depend on three dimensionless groups, namely: (1) the residual saturation of brine after displacement by CO₂; (2) the ratio of CO₂ mobility to brine mobility; (3) a dimensionless group (which we call a “gravity factor”) that quantifies the importance of CO₂ buoyancy relative to CO₂ injection rate. In the particular case of negligible residual brine saturation and negligible buoyancy effects, the storage efficiency is approximately equal to the ratio of the CO₂ viscosity to the brine viscosity. Storage efficiency decreases as the gravity factor increases, because the buoyancy of the CO₂ causes it to occupy a thin layer at the top of the confined formation, while leaving the lower part of the aquifer under-utilized. Estimates of storage efficiency from our simple analytical expressions are in reasonable agreement with values calculated from simulations performed with more complicated multi-phase-flow simulation software. Therefore, we suggest that the analytical expressions presented herein could be used as a simple and rapid tool to screen the technical or economic feasibility of a proposed CO₂ injection scenario.     

Long-term variations of CO2 trapped in different mechanisms in deep saline formations: A case study of the Songliao Basin,China

The geological storage of CO₂ in deep saline formations is increasing seen as a viable strategy to reduce the release of greenhouse gases to the atmosphere. There are numerous sedimentary basins in China, in which a number of suitable CO₂ geologic reservoirs are potentially available. To identify the multi-phase processes, geochemical changes and mineral alteration, and CO₂ trapping mechanisms after CO₂ injection, reactive geochemical transport simulations using a simple 2D model were performed. Mineralogical composition and water chemistry from a deep saline formation of Songliao Basin were used. Results indicate that different storage forms of CO₂ vary with time. In the CO₂ injection period, a large amount of CO₂ remains as a free supercritical phase (gas trapping), and the amount dissolved in the formation water (solubility trapping) gradually increases. Later, gas trapping decrease, solubility trapping increases significantly due to the migration and diffusion of CO₂ plume and the convective mixing between CO₂-saturated water and unsaturated water, and the amount trapped by carbonate minerals increases gradually with time. The residual CO₂ gas keeps dissolving into groundwater and precipitating carbonate minerals. For the Songliao Basin sandstone, variations in the reaction rate and abundance of chlorite, and plagioclase composition affect significantly the estimates of mineral alteration and CO₂ storage in different trapping mechanisms. The effect of vertical permeability and residual gas saturation on the overall storage is smaller compared to the geochemical factors. However, they can affect the spatial distribution of the injected CO₂ in the formations. The CO₂ mineral trapping capacity could be in the order of 10 kg/m³ medium for the Songliao Basin sandstone, and may be higher depending on the composition of primary aluminosilicate minerals especially the content of Ca, Mg, and Fe.     

Simultaneous CO2 injection and water production to optimise aquifer storage capacity

The estimates for geological CO₂ storage capacity worldwide vary, but it is generally believed that the capacity in saline aquifers will be sufficient for the amounts of CO₂ that will need to be stored. The effort required to select and qualify a geological storage site for safe storage will, however, be significant and storage capacity may be a limited resource regionally. Both from a economic and resource management perspective it is therefore important that potential storage sites are exploited to their full potential.In static capacity estimates, where the maximum stored amount of CO₂ is given as a fraction of the formation pore volume, typically arrive at efficiency factors in the range of a few per cents. Recent work has shown that when the dynamic behaviour of the injected CO₂ is taken into account, the efficiency factor will be reduced because of the increase in pore pressure in the region around the injection well(s). The increase in pore pressure will propagate much further than the CO₂. The EU directive on geological CO₂ storage specifically addresses the restriction that will apply when different storage sites are interacting due to pressure communication. Consequently, the pore pressure increase at the boundary of the storage license area will be an important limiting factor for the amount of CO₂ that can be injected.One obvious method to control the pore pressure is to produce water from the aquifer at some distance from the CO₂ injection wells. This paper discusses results from simulations of CO₂ injection in two aquifers on the Norwegian Continental Shelf; the Johansen aquifer and the southern part of the Utsira aquifer. These aquifers are candidates for injection of CO₂ shipped out via pipeline from the Norwegian West Coast. The injected amounts of CO₂ over a period of 50 years are 0.518 Gtonne for the Johansen aquifer and 1.04 Gtonne for the Utsira aquifer.Several design options for the injection operations are investigated: Injection of CO₂ without water production; injection into several wells to distribute the injected fluids and reduce the local pressure increase around each injection well; and injection with simultaneous production of water from one or more wells. The boundaries of the aquifer formations are assumed closed in all simulations. The possible consequences of other types of boundary conditions (semi-closed or open) are briefly discussed.