Characterization of emissions from portable household combustion devices: particle size distributions,emission rates and factors,and potential exposures

A series of source tests were conducted to characterize emissions of particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO₂), methane (CH₄), and total hydrocarbon (THC ) from five types of portable combustion devices. Tested combustion devices included a kerosene lamp, an oil lamp, a kerosene space heater, a portable gas range, and four unscented candles. All tests were conducted either in a well-mixed chamber or a well-mixed room, which enables us to determine emission rates and emission factors using a single-compartment mass balance model. Particle mass concentrations and number concentrations were measured using a nephelometric particle monitor and an eight-channel optical particle counter, respectively. Real-time CO concentrations were measured with an electrochemical sensor CO monitor. CO₂, CH₄, and THC were measured using a GC-FID technique. The results indicate that all particles emitted during steady burning in each of the tested devices were smaller than 1.0 μm in diameter with the vast majority in the range between 0.1 and 0.3 μm. The PM mass emission rates and emission factors for the tested devices ranged from 5.6±0.1 to 142.3±40.8 mg h⁻¹ and from 0.35±0.06 to 9.04±4.0 mg g⁻¹, respectively. The CO emission rates and emission factors ranged from 4.7±3.0 to 226.7±100 mg h⁻¹ and from 0.25±0.12 to 1.56±0.7 mg g⁻¹, respectively. The CO₂ emission rates and emission factors ranged from 5500±700 to 210,000±90,000 mg h⁻¹ and from 387±45 to 1689±640 mg g⁻¹, respectively. The contributions of CH₄ and THC to emission inventories are expected to be insignificant due both to the small emission factors and to the relatively small quantity of fuel consumed by these portable devices. An exposure scenario analysis indicates that every-day use of the kerosene lamp in a village house can generate fine PM exposures easily exceeding the US promulgated NAAQS for PM_2.5.     

Methane emissions from lakes and floodplains in Pantanal,Brazil

To evaluate the tropical wetlands contribution to the methane (CH₄) burden better, field campaigns were performed during 2004 and 2005 near the Miranda River, in five sites inside the Brazilian Pantanal region. The CH₄ fluxes were determined using the static chamber technique. Environmental variables that may affect CH₄ emissions, as the water depth, the water and air temperatures were also measured. The overall average of the 320 individual CH₄ flux measurements made between March/2004 and March/2005 was 142±314 mg CH₄ m⁻² d⁻¹, which is a value near the ones observed in other tropical flooded regions. About 47% of the fluxes measurements presented nonlinear increases in the chamber concentrations, which were assumed to be linked to CH₄ losses through bubbles. The bubble flux represented about 90% of the total CH₄ losses in the measurements and ranged from 1 to 2187 mg CH₄ m⁻² d⁻¹ with an average of 292±410 mg CH₄ m⁻² d⁻¹ (median: 153 mg CH₄ m⁻² d⁻¹). The diffusive flux ranged from 1 to 124 mg CH₄ m⁻² d⁻¹, with an average of 10±17 mg CH₄ m⁻² d⁻¹ (median: 5 mg CH₄ m⁻² d⁻¹). The fluxes from lakes were smaller than those observed in the floodplains, where the flooding was more dependent on the seasonal cycle. The diffusive flux showed a slight, but not statistically significant seasonal variation, following the seasonal variation of the flooding of the Pantanal region. A rough estimative of the total annual CH₄ emission shows that the contribution of the Pantanal is about 3.3 Tg CH₄ yr⁻¹, which represents about 3.3% of the total CH₄ emissions estimated to be originated in wetlands ecosystems. It may be a conservative estimate, which may present a large interannual variation, since it was obtained during one of the lowest flood of the Pantanal in recent years.     

Preparation of controlled nano-MgO and investigation of its bactericidal properties

Nano-MgO is a good bactericide but with strong alkalinity in water due to its rapid hydrolysis. To control its hydrolysis rate and keep its bactericidal properties, we synthesized nano-MgO microspheres using chitosan–alginate system in this study. The synthesized nano-MgO release-controlled microspheres (nMgO-RCM) were with 0.98–1.20 mm of particle sizes. Also, their embedding ratio and loading percentage was 63.52% and 12.27%, respectively. Based on the characterization results, nano-MgO was only observed on surface of the nMgO-RCM. Its release rate from the nMgO-RCM could be controlled by the chitosan–alginate system, and the observed rate constant (k_obs) increased from 0.0289 h⁻¹ to 0.0358 h⁻¹ with the increment of the dosage from 10 mg L⁻¹ to 80 mg L⁻¹. Furthermore, the nMgO-RCM could maintain pH value lower than 8.5 and colony counts less than 20 CFU mL⁻¹ for at least 120 h.     

Winter-grazing reduces methane uptake by soils of a typical semi-arid steppe in Inner Mongolia,China

Steppe ecosystems are regarded as an important sink of atmospheric methane (CH₄) and grazing is hypothesized to reduce CH₄ uptake. However, firm experimental evidence is required to prove this hypothesis. Using a fully automated, chamber-based measuring system, we conducted continuous high-frequency (at a 3-h interval) measurements of CH₄ uptake in a Leymus chinensis steppe, which is a typical grassland ecosystem in Inner Mongolia, China. Two management regimes were investigated: ungrazed since 1999 (UG99) and winter-grazed since 2001 (WG01). Measurements were carried out continuously during the periods of June–September 2004, May–September 2005 and March–June 2006. During all of these periods, significantly lower mean CH₄ uptake (±S.E.) at WG01 (28±0.7 μg C m⁻² h⁻¹) as compared to UG99 (56±1.0 μg C m⁻² h⁻¹) (p<0.01) was found. Total CH₄ uptake during the growing seasons (May–September) 2004 and 2005 at WG01 and UG99 was quantified as 1.15 and 2.15 kg C ha⁻¹, respectively. Annual rates of CH₄ uptake were approximately 1.91 (WG01) and 3.58 kg C ha⁻¹ (UG99), respectively. These results indicate that winter-grazing of steppe significantly reduced atmospheric CH₄ uptake by ca. 47%. The winter-grazing practice may have inhibited CH₄ uptake by (a) increasing the likelihood of physiological water stress for CH₄-consuming bacteria during dry periods, (b) decreasing gas diffusion into the soil and, (c) reducing the populations of CH₄ oxidizing bacteria. These three mechanisms could have collectively or independently facilitated the observed inhibitory effects. Our results suggest that grazing exerts a considerable negative impact on CH₄ uptake in semi-arid steppes at regional scales. Notwithstanding, further studies involving year-round, intensive measurements of CH₄ uptake are needed.     

Trace gas variations at Cape Point,South Africa,during May 1997 following a regional biomass burning episode

During the continuous monitoring of atmospheric parameters at the station Cape Point (34°S, 18°E), a smoke plume originating from a controlled fire of 30-yr-old fynbos was observed on 6 May 1997. For this episode, which was associated with a nocturnal inversion and offshore airflow, atmospheric parameters (solar radiation and meteorological data) were considered and the levels of various trace gases compared with those measured at Cape Point in maritime air. Concentration maxima in the morning of 6 May for CO₂, CO, CH₄ and O₃ amounted to 370.3 ppm, 491 ppb, 1730 ppb and 47 ppb, respectively, whilst the mixing ratios of several halocarbons (F-11, F-12, F-113, CCl₄ and CH₃CCl₃) remained at background levels. In the case of CO, the maritime background level for this period was exceeded by a factor of 9.8. Differences in ozone levels of up to 5 ppb between air intakes at 4 and 30 m above the station (located at 230 m above sea level) indicated stratification of the air advected to Cape Point during the plume event. Aerosols within the smoke plume caused the signal of global solar radiation and UV–A to be attenuated from 52.4 to 13.0 mW cm⁻² and from 2.3 to 1.3 mW cm⁻², respectively, 5 h after the trace gases had reached their maxima. Emission ratios (ERs) calculated for CO and CH₄ relative to CO₂ mixing ratios amounted to 0.042 and 0.0040, respectively, representing one of the first results for fires involving fynbos. The CO ER is somewhat lower than those given in the literature for African savanna fires (average ER=0.048), whilst for CH₄ the ER falls within the range of ERs reported for the flaming (0.0030) and smouldering phases (0.0055) of savanna fires. Non-methane hydrocarbon (NMHC) data obtained from a grab sample collected during the plume event were compared to background levels. The highest ERs (ΔNMHC/ΔCH₄) have been obtained for the C₂–C₃ hydrocarbons (e.g. ethene at 229.3 ppt ppb⁻¹), whilst the C₄–C₇ hydrocarbons were characterised by the lowest ERs (e.g. n-hexane at 1.0 and n-pentane at 0.8 ppt ppb⁻¹).     

Decadal reductions of traffic emissions on a transit route in Austria – results of the Tauerntunnel experiment 1997

Real-world emissions of a traffic fleet on a transit route in Austria were determined in the Tauerntunnel experiment in October 1997. The total number of vehicles and the average speed was nearly the same on both measuring days (465 vehicles 30 min⁻¹ and 76 km h⁻¹ on the workday, 477 and 78 km h⁻¹ on Sunday). The average workday fleet contained 17.6% heavy-duty vehicles (HDV) and the average Sunday fleet 2.8% HDV resulting in up to four times higher emission rates per vehicle per km on the workday than on Sunday for most of the regulated components (CO₂, CO, NO_x, SO₂, and particulate matter-PM10). Emission rates of NMVOC accounted for 200 mg vehicle⁻¹ km⁻¹ on both days. The relative contributions of light-duty vehicles (LDV) and HDV to the total emissions indicated that aldehydes, BTEX (benzene, toluene, ethylbenzene, xylenes), and alkanes are mainly produced by LDV, while HDV dominated emissions of CO, NO_x, SO₂, and PM10. Emissions of NO_x caused by HDV were 16,100 mg vehicle⁻¹ km⁻¹ (as NO₂). Produced by LDV they were much lower at 360 mg vehicle⁻¹ km⁻¹. Comparing the emission rates to the results that were obtained by the 1988 experiment at the same place significant changes in the emission levels of hydrocarbons and CO, which accounted 1997 to only 10% of the levels in 1988, were noticed. However, the decrease of PM has been modest leading to values of 80 and 60% of the levels in 1988 on the workday and on Sunday, respectively. Emission rates of NO_x determined on the workday in 1997 were 3130 mg vehicle⁻¹ km⁻¹ and even higher than in 1988 (2630 mg vehicle⁻¹ km⁻¹), presumable due to the increase of the HD-traffic.     

Gaseous emissions from outdoor concrete yards used by livestock

Measurements of ammonia (NH₃), nitrous oxide (N₂O) and methane (CH₄) were made from 11 outdoor concrete yards used by livestock. Measurements of NH₃ emission were made using the equilibrium concentration technique while closed chambers were used to measure N₂O and CH₄ emissions. Outdoor yards used by livestock proved to be an important source of NH₃ emission. Greatest emission rates were measured from dairy cow feeding yards, with a mean of 690 mg NH₃-N m⁻² h⁻¹. Smaller emission rates were measured from sheep handling areas, dairy cow collecting yards, beef feeding yards and a pig loading area, with respective mean emission rates of 440, 280, 220 and 140 mg NH₃-N m⁻² h⁻¹. Emission rates of N₂O and CH₄ were much smaller and for CH₄, in particular, emission rates were influenced greatly by the presence or absence of dung on the measurement area.     

Effect of natural compounds on reducing formaldehyde emission from plywood

The effects of natural compounds on reducing formaldehyde emission from plywood were investigated. Urea, catechin and vanillin were examined as the natural formaldehyde reducers. The microemission cell, with an internal volume of 35 ml, the maximum exposed test surface area of 177 cm² and an air purge flow rate of 50 ml min⁻¹, was used to measure specific emission rate (SER). In the case of no reducer treatment, formaldehyde emission from plywood was fast and SERs were 4.4 mg m⁻² h⁻¹ at 30 °C and 15 mg m⁻² h⁻¹ at 60 °C. When this plywood was treated with the natural compounds, the SERs of formaldehyde were decreased at all temperatures. In the case of urea treatment, the SERs of formaldehyde decreased to 0.30 mg m⁻² h⁻¹ at 30 °C and 0.65 mg m⁻² h⁻¹ at 60 °C. When the urea treatment was applied to the inside of kitchen cabinet (made from plywood; 270 cm wide, 60 cm deep, 250 cm high), the concentration of formaldehyde was reduced substantially from 1600 to 130 μg m⁻³. The reducing effect of formaldehyde continued during the observation period (6 months), with a mean concentration of 100 μg m⁻³. Reducers in the plywood would react with released formaldehyde. Application of natural compounds such as urea, catechin and vanillin could provide a simple and effective approach for suppressing formaldehyde emission from plywood.     

Isoprene and monoterpene fluxes measured above Amazonian rainforest and their dependence on light and temperature

Canopy scale emissions of isoprene and monoterpenes from Amazonian rainforest were measured by eddy covariance and eddy accumulation techniques. The peak mixing ratios at about 10 m above the canopy occurred in the afternoon and were typically about 90 ppt_v of α-pinene and 4–5 ppb_v of isoprene. α-pinene was the most abundant monoterpene in the air above the canopy comprising ≈50% of the total monoterpene mixing ratio. Measured isoprene fluxes were almost 10 times higher than α-pinene fluxes. Normalized conditions of 30°C and 1000 μmol m⁻² s⁻¹ were associated with an isoprene flux of 2.4 mg m⁻² h⁻¹ and a β-pinene flux of 0.26 mg m⁻² h⁻¹. Both fluxes were lower than values that have been specified for Amazon rainforests in global emission models. Isoprene flux correlated with a light- and temperature-dependent emission activity factor, and even better with measured sensible heat flux. The variation in the measured α-pinene fluxes, as well as the diurnal cycle of mixing ratio, suggest emissions that are dependent on both light and temperature. The light and temperature dependence can have a significant effect on the modeled diurnal cycle of monoterpene emission as well as on the total monoterpene emission.     

The effects of evaporating essential oils on indoor air quality

Essential oils, predominantly comprised of a group of aromatic chemicals, have attracted increasing attention as they are introduced into indoor environments through various forms of consumer products via different venues. Our study aimed to characterize the profiles and concentrations of emitted volatile organic compounds (VOCs) when evaporating essential oils indoors. Three popular essential oils in the market, lavender, eucalyptus, and tea tree, based on a nation-wide questionnaire survey, were tested. Specific aromatic compounds of interest were sampled during evaporating the essential oils, and analyzed by GC-MS. Indoor carbon monoxide (CO), carbon dioxide (CO₂), total volatile organic compounds (TVOCs), and particulate matters (PM₁₀) were measured by real-time, continuous monitors, and duplicate samples for airborne fungi and bacteria were collected in different periods of the evaporation. Indoor CO (average concentration 1.48 vs. 0.47 ppm at test vs. background), CO₂ (543.21 vs. 435.47 ppm), and TVOCs (0.74 vs. 0.48 ppm) levels have increased significantly after evaporating essential oils, but not the PM₁₀ (2.45 vs. 2.42 ppm). The anti-microbial activity on airborne microbes, an effect claimed by the use of many essential oils, could only be found at the first 30–60 min after the evaporation began as the highest levels of volatile components in these essential oils appeared to emit into the air, especially in the case of tea tree oil. High emissions of linalool (0.092–0.787 mg m⁻³), eucalyptol (0.007–0.856 mg m⁻³), d-limonene (0.004–0.153 mg m⁻³), ρ-cymene (0.019–0.141 mg m⁻³), and terpinene-4-ol-1 (0.029–0.978 mg m⁻³), all from the family of terpenes, were observed, and warranted for further examination for their health implications, especially for their potential contribution to the increasing indoor levels of secondary pollutants such as formaldehyde and secondary organic aerosols (SOAs) in the presence of ozone.     

Long-term measurements of SO2 dry deposition over Gansu Province,China

Potassium carbonate sulfation plates, monitored monthly for 11 years from 48 sites in 11 cities in Gansu Province, China, provide a crude estimate of cumulative SO₂ dry depositions. Measured SO₂ dry deposition rates were 1.6–472 mg m⁻² day⁻¹ and had seasonal variations with maxima in winter and minima mainly during summer as a result of higher winter and lower summer SO₂ concentrations. The 11-year monthly average SO₂ dry deposition rates are 23.2–248.97 and 11.7–175.6 mg m⁻² day⁻¹ in the eleven cities in winter and summer, respectively. A monthly average SO₂ deposition velocity was also estimated from 0.06 to 9.72 cm s⁻² in the 11 cities studied with a 11-year average maximum value of about 1.1–2.7 cm s⁻² in April and July and a 11-year average minimum value of about 0.2–1.0 cm s⁻¹ in January. The SO₂ dry deposition velocity also exhibits an increasing with wind speed in basins of less than 500 mm annual precipitation. In contrast, due to influences of the relative humidity in valleys of more than 500 mm annual precipitation, it shows a decreasing trend with wind speed increasing.     

Responses of two birch (Betula pendula Roth) clones to different ozone profiles with similar AOT40 exposure

Saplings of two clones of European white birch (Betula pendula Roth) were exposed to three different ozone profiles resulting in same AOT40 value of 13–14 ppm h in a chamber experiment. The sensitive clone 5 and the more tolerant clone 2 were growing (1) under filtered air (=control), or (2) were exposed to 70 ppb ozone for 24 h d⁻¹ (=profile 1), (3) to 100 ppb ozone for 12 h d⁻¹ at 8:00–20:00 (=profile 2), or (4) to 200 ppb ozone for 4.5 h d⁻¹ at 9:30–14:00 (=profile 3) for 20 d. The saplings were determined for growth, visible leaf injuries, stomatal conductance, and concentrations of Rubisco, chlorophyll and carotenoids. Growth responses and induction of visible foliar injuries under different ozone profiles were variable, resulting in 4–17% lower dry mass of shoot, 16–46% reduction in stem height increment and 11–43% increase in visible injuries in clone 5, which was accompanied by higher leaf turnover rate under profile 3 indicating compensation growth. In clone 2, ozone-induced responses ranged from slight stimulation in stem height growth to 13% decrease in dry mass of shoot and 2–16% increase in visible injuries. Daytime stomatal conductance rates were lowered by 14–54% in clone 5 and 9–74% in clone 2, depending on profile. The additional power-weighted analyses revealed that high peak concentrations and exposure shape were important for induction of visible injuries in both clones and reduction in stomatal conductance in clone 5, whereas growth reductions were rather related to total cumulative exposure. The results indicate that profile of ozone exposure, night-time stomatal conductance (24 h flux), and recovery time for defence and compensations reactions should not be ignored in plant response and ozone flux modelling.     

An on-line analysis of reduced sulfur gases in the ambient air surrounding a large industrial complex

In this study, the concentrations of reduced sulfur compounds (RSC: H₂S, CH₃SH, DMS, and DMDS) were continuously measured from an odor monitoring station over a 4-month period (August–November 2005) using an on-line GC system. The hourly measurement data of RSC, collected along with some major aromatic VOCs (benzene, toluene, xylene, etc.), approached the sum of 1500; the mean for all hourly H₂S was computed to be 295 ppt, while those of the others were seen at 7 (DMS), 1 (CH₃SH), and 0.4 ppt (DMDS). When these RSC data were compared across two seasons and on a 24 h scale basis, the values for either the summer or nighttime periods were generally high relative to their counterparts in the fall and daytime. Analysis of these RSC data generally suggests that most RSCs occur at some ppt concentration ranges and that their values frequently fall below detection limits (DL) values (except for H₂S). If the total number of effective data sets (i.e., above DL values) are compared to each other, the results tend to differ significantly between H₂S and the others: the proportion of effective number was as high as 75% for H₂S, while the others were very low (6% of DMS and even less than that for the others). The distributions of RSC were hence clearly distinguished from those of VOCs in that the determination of the latter was scarcely limited by the instrumental detectability. According to the present study, the H₂S data exhibit strong potential as the malodor tracers, while those of the other RSCs are unlikely due to the limited detectability. The overall results of this study hence suggest that several factors which include the selection of target compounds, the location of the monitoring points, and the scale (or number) of total monitoring points should be considered simultaneously to effectively track down the odor occurrence patterns in areas near strong source processes.     

Transport of SO2 and aerosol over the Yellow sea

Aircraft measurements of air pollutants were made to investigate the characteristic features of long-range transport of sulfur compounds over the Yellow Sea for the periods of 26–27 April and 7–10 November in 1998, and 9–11 April and 19 June in 1999, together with aerosol measurements at the Taean background station in Korea. The overall mean concentrations of SO₂, O₃ and aerosol number in the boundary layer for the observation period ranged 0.1–7.4 ppb 32.1–64.1 ppb and 1.0–143.6 cm⁻³, respectively. It was found that the air mass over the Yellow Sea had a character of both the polluted continental air and clean background air, and the sulfur transport was mainly confined in the atmospheric boundary layer. The median of SO₂ concentration within the boundary layer was about 0.1–2.2 ppb. However, on 8 November, 1998, the mean concentrations of SO₂ and aerosol number increased up to 7.4 ppb and 109.5 cm⁻³, respectively, in the boundary layer, whereas O₃ concentration decreased remarkably. This enhanced SO₂ concentration occurred in low level westerly air stream from China to Korea. Aerosol analyses at the downstream site of Taean in Korea showed 2–3 times higher sulfate concentration than that of other sampling days, indicating a significant amount of SO₂ conversion to non sea-salt sulfate during the long-range transport.     

Eddy flux measurements of methane over the fen “Murnauer Moos”, 11°11′E, 47°39′N,using a fast tunable diode laser spectrometer

Eddy covariance measurements of methane were carried out over the fen “Murnauer Moos” in the south of Germany in order to evaluate the performance of a newly developed eddy covariance measurement system, based on a frequency-modulated tunable diode laser spectrometer as a fast chemical sensor. During a six-day period, an average daytime methane emission of (5.4±1.8) mg CH₄ m⁻² h⁻¹ was measured. We find this value moderate, considering the favorable meteorological and soil conditions for methane emission. Diurnal cycles of the fluxes of methane and carbon dioxide as well as of sensible and latent heat are presented. Results are discussed in terms of relevant micrometeorological quantities, and quality control procedures based on Allan variance and spectral analysis are discussed.     

Real-world emission factors of fifteen carbonyl compounds measured in a Hong Kong tunnel

Real-world vehicle emissions of carbonyls were determined in summer and winter of 2003 at the Shing Mun Tunnel, Hong Kong. Fifteen carbonyl species have been analyzed in this study. The total measured carbonyls emission factors ranged from 21.7 to 68.9 mg veh⁻¹ km⁻¹ among different measurement periods, with an average of 35.8±11.9 mg veh⁻¹ km⁻¹. Higher carbonyl emissions were found to be associated with a high proportion of diesel-fueled vehicles. Total measured carbonyl emissions from Diesel-fueled Vehicle (DV, 71.5 mg veh⁻¹ km⁻¹) were about 7 times higher than those from Non-Diesel-fueled Vehicle (NDV, 10 mg veh⁻¹ km⁻¹). The five carbonyls with the largest DV emission factor were, in decreasing order, formaldehyde (38.3 mg veh⁻¹ km⁻¹), acetaldehyde (11.4 mg veh⁻¹ km⁻¹), acetone (5.3 mg veh⁻¹ km⁻¹), crotonaldehyde (5.2 mg veh⁻¹ km⁻¹) and benzaldehyde (2.0 mg veh⁻¹ km⁻¹). These five carbonyl compounds together accounted for 87% of the sum of all DV carbonyl emission factors. For NDV, the five most abundant carbonyls in NDV emission at the tunnel were, in decreasing order, formaldehyde (3.5 mg veh⁻¹ km⁻¹), acetone (1.8 mg veh⁻¹ km⁻¹), methyl ethyl ketone (1.6 mg veh⁻¹ km⁻¹), m,p-tolualdehyde (1.0 mg veh⁻¹ km⁻¹) and acetaldehyde (mg veh⁻¹ km⁻¹). They accounted for 85% of the sum of all NDV carbonyl emission factors.     

Temporal and spatial variation of sulfur-gas-transfer between coastal marine sediments and the atmosphere

The spatial and temporal variability of sulfur gas fluxes (H₂S, COS, CH₃SH, DMS, and CS₂) at the sediment–air interface were studied in the intertidal Wadden Sea area of Sylt-Rømø (Germany/Denmark) during eight measuring campaigns between June 1991 and September 1994. Measurements were performed mainly at four sites in a sheltered intertidal bay of approximately 6 km² (Königshafen) and discontinuously in a wider range of the 400 km² Sylt-Rømø tidal flat area. In situ fluxes of the S-gases were determined by a dynamic chamber technique focusing on dry sediment periods. Additional experiments were conducted in order to determine changes in S-gas concentrations in the sediment between the surface and 70 cm depth.In most cases H₂S was the dominant S-gas emitted from the sediment to the atmosphere, contributing up to 70% of the total S-emission at this interface. Mean H₂S emission rates ranged between 0.07 and 9.95 μg S m^-2 h^-1. Both emission rates and relative contribution of H₂S were lowest from fine sand and highest from muddy sites. Diurnal variation of H₂S emission was evident in summer and fall with up to 10-fold higher rates during night than during the day. Distinct seasonal variation of H₂S-transfer between the sediment and the atmosphere was observed with higher emission rates in the summer than in spring or fall. The emission of H₂S to the atmosphere was smaller by a factor of 1600–26 000 than the H₂S produced from sulfate reduction. Apparently, the efficiency by which H₂S produced in the sediment is retained and reoxidized by biogeochemical sediment processes is extremely high. Carbonyl sulfide (COS) was emitted with relatively constant rates in space and time with mean flux rates ranging between 0.24 and 2.0 μg S m^-2 h^-1. Carbon disulfide emission rates were comparable to those of COS and varied between 0.3 and 2.23 μg S m^-2 h^-1. DMS played a minor role in the S-gas transfer from uncovered sediment areas contributing between 3.1 and 23% to total S-emission from the sediment to the atmosphere.     

Air–land exchanges of CO2, CH4 and N2O measured by FTIR spectrometry and micrometeorological techniques

Micrometeorological flux-gradient and nocturnal boundary layer methods were combined with Fourier transform infrared (FTIR) spectroscopy for high-precision trace gas analysis to measure fluxes of the trace gases CO₂, CH₄ and N₂O between agricultural fields and the atmosphere. The FTIR measurements were fully automated and routinely obtained a precision of 0.1–0.2% for several weeks during a measurement campaign in October 1995. In flux-gradient measurements, vertical profiles of the trace gases were measured every 30 min from the ground to 22 m. When combined with independent micrometeorological measurements of water vapour fluxes, trace gas fluxes from the underlying surface could be determined. In the nocturnal boundary layer method the rate of change in mass storage in the 0–22 m layer was combined with fluxes measured at 22 m to estimate surface fluxes. Daytime fluxes for CO₂ were −0.78±0.40 (1σ) mg CO₂ m⁻² s⁻¹. Daytime fluxes of N₂O and CH₄ were very small and difficult to measure reliably using the flux-gradient technique, despite the high precision of the concentration measurements. Mean daytime flux for N₂O was 17±48 ng N m⁻² s⁻¹, while the corresponding flux for CH₄ was 47±410 ng CH₄ m⁻² s⁻¹. The mean nighttime flux of CO₂ estimated using the nocturnal boundary layer method was +0.15±0.05 mg CO₂ m⁻² s⁻¹, in good agreement with chamber measurements of respiration rates. Nighttime fluxes of CH₄ and N₂O from the nocturnal boundary layer method were 109±69 ng CH₄ m⁻² s⁻¹ and 2±3.2 ng N m⁻² s⁻¹, respectively, in good agreement with chamber measurements and inventory estimates based on the sheep and cattle stocking rates in the region. The suitability of FTIR-based methods for long term monitoring of spatially and temporally averaged flux measurements is discussed.     

Emission factors of PAHs,methoxyphenols, levoglucosan,elemental carbon and organic carbon from simulated wheat and Kentucky bluegrass stubble burns

Emission factors (EFs) of pollutants from post-harvest agricultural burning are required for predicting downwind impacts of smoke and inventorying emissions. EFs of polycyclic aromatic hydrocarbons (PAH), methoxyphenols (MP), levoglucosan (LG), elemental carbon (EC) and organic carbon (OC) from wheat and Kentucky bluegrass (KBG) stubble burning were quantified in a US EPA test burn facility. The PAH and MP EFs for combined solid+gas phases are 17±8.2 mg kg⁻¹ and 79±36 mg kg⁻¹, respectively, for wheat and 21±15 mg kg⁻¹ and 35±24 mg kg⁻¹, respectively, for KBG. LG, particulate EC and artifact-corrected OC EFs are 150±130 mg kg⁻¹, 0.35±0.16 g kg⁻¹ and 1.9±1.1 g kg⁻¹, respectively, for wheat and 350±510 mg kg⁻¹, 0.63±0.056 g kg⁻¹ and 6.9±0.85 g kg⁻¹, respectively, for KBG. Positive artifacts associated with OC sampling were evaluated and remedied with a two-filter system. EC and OC accounted for almost two-thirds of PM_2.5 mass, while LG accounted for just under 3% of the PM_2.5 mass. Since EFs of these pollutants generally decreased with increasing combustion efficiency (CE), identifying and implementing methods of increasing the CEs of burns would help reduce their emissions from agricultural field burning. PAH, OC and EC EFs are comparable to other similar studies reported in literature. MP EFs appear dependent on the stubble type and are lower than the EFs for hard and softwoods reported in literature, possibly due to the lower lignin content in wheat and KBG.     

A novel field measurement method for determining fine particle and gas emissions from residential wood combustion

Emission data from residential wood combustion are usually obtained on test stands in the laboratory but these measurements do not correspond to the operational conditions in the field because of the technological boundary conditions (e.g. testing protocol, environmental and draught conditions). The field measurements take into account the habitual practice of the operators and provide the more reliable results needed for emission inventories. In this study, a workable and compact method for measuring emissions from residential wood combustion in winter conditions was developed. The emissions for fine particle, gaseous and PAH compounds as well as particle composition in real operational conditions were measured from seven different appliances. The measurement technique worked well and was evidently suitable for winter conditions. It was easy and fast to use, and no construction scaffold was needed. The dilution of the sample with the combination of a porous tube diluter and an ejector diluter was well suited to field measurement. The results indicate that the emissions of total volatile organic carbon (TVOC) (17 g kg⁻¹ (of dry wood burned)), carbon monoxide (CO) (120 g kg⁻¹) and fine particle mass (PM₁) (2.7 g kg⁻¹) from the sauna stove were higher than in the other measured appliances. In the masonry heaters, baking oven and stove, the emissions were 2.9–9 g kg⁻¹ TVOC, 28–68 g kg⁻¹ CO and 0.6–1.6 g kg⁻¹ PM₁. The emission of 12 PAHs (PAH₁₂) from the sauna stove was 164 mg kg⁻¹ and consisted mainly of PAHs with four benzene rings in their structure. PAH₁₂ emission from other appliances was, on average, 21 mg kg⁻¹ and was dominated by 2-ring PAHs. These results indicate that despite the non-optimal operational practices in the field, the emissions did not differ markedly from the laboratory measurements.