Characteristics of carbonyls: Concentrations and source strengths for indoor and outdoor residential microenvironments in China

Indoor and outdoor carbonyl concentrations were measured simultaneously in 12 urban dwellings in Beijing, Shanghai, Guangzhou, and Xi’an, China in summer (from July to September in 2004) and winter (from December 2004 to February 2005). Formaldehyde was the most abundant indoor carbonyls species, while formaldehyde, acetaldehyde and acetone were found to be the most abundant outdoor carbonyls species. The average formaldehyde concentrations in summer indoor air varied widely between cities, ranging from a low of 19.3 μg m⁻³ in Xi’an to a high of 92.8 μg m⁻³ in Beijing. The results showed that the dwellings with tobacco smoke, incense burning or poor ventilation had significantly higher indoor concentrations of certain carbonyls. It was noticed that although one half of the dwellings in this study installed with low emission building materials or furniture, the carbonyls levels were still significantly high. It was also noted that in winter both the indoor and outdoor acetone concentrations in two dwellings in Guangzhou were significantly high, which were mainly caused by the usage of acetone as industrial solvent in many paint manufacturing and other industries located around Guangzhou and relatively longer lifetime of acetone for removal by photolysis and OH reaction than other carbonyls species. The indoor carbonyls levels in Chinese dwellings were higher than that in dwellings in the other countries. The levels of indoor and ambient carbonyls showed great seasonal differences. Six carbonyls species were carried out the estimation of indoor source strengths. Formaldehyde had the largest indoor source strength, with an average of 5.25 mg h⁻¹ in summer and 1.98 mg h⁻¹ in winter, respectively. However, propionaldehyde, crotonaldehyde and benzaldehyde had the weakest indoor sources.     

Ozone reactions with indoor materials during building disinfection

There is scant information related to heterogeneous indoor chemistry at ozone concentrations necessary for the effective disinfection of buildings, i.e., hundreds to thousands of ppm. In the present study, 24 materials were exposed for 16 h to ozone concentrations of 1000–1200 ppm in the inlet streams of test chambers. Initial ozone deposition velocities were similar to those reported in the published literature for much lower ozone concentrations, but decayed rapidly as reaction sites on material surfaces were consumed. For every material, deposition velocities converged to a relatively constant, and typically low, value after approximately 11 h. The four materials with the highest sustained deposition velocities were ceiling tile, office partition, medium density fiberboard and gypsum wallboard backing. Analysis of ozone reaction probabilities indicated that throughout each experiment, and particularly after several hours of disinfection, surface reaction resistance dominated the overall resistance to ozone deposition for nearly all materials. Total building disinfection by-products (all carbonyls) were quantified per unit area of each material for the experimental period. Paper, office partition, and medium density fiberboard each released greater than 38 mg m⁻² of by-products.     

Characterization of emissions from portable household combustion devices: particle size distributions,emission rates and factors,and potential exposures

A series of source tests were conducted to characterize emissions of particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO₂), methane (CH₄), and total hydrocarbon (THC ) from five types of portable combustion devices. Tested combustion devices included a kerosene lamp, an oil lamp, a kerosene space heater, a portable gas range, and four unscented candles. All tests were conducted either in a well-mixed chamber or a well-mixed room, which enables us to determine emission rates and emission factors using a single-compartment mass balance model. Particle mass concentrations and number concentrations were measured using a nephelometric particle monitor and an eight-channel optical particle counter, respectively. Real-time CO concentrations were measured with an electrochemical sensor CO monitor. CO₂, CH₄, and THC were measured using a GC-FID technique. The results indicate that all particles emitted during steady burning in each of the tested devices were smaller than 1.0 μm in diameter with the vast majority in the range between 0.1 and 0.3 μm. The PM mass emission rates and emission factors for the tested devices ranged from 5.6±0.1 to 142.3±40.8 mg h⁻¹ and from 0.35±0.06 to 9.04±4.0 mg g⁻¹, respectively. The CO emission rates and emission factors ranged from 4.7±3.0 to 226.7±100 mg h⁻¹ and from 0.25±0.12 to 1.56±0.7 mg g⁻¹, respectively. The CO₂ emission rates and emission factors ranged from 5500±700 to 210,000±90,000 mg h⁻¹ and from 387±45 to 1689±640 mg g⁻¹, respectively. The contributions of CH₄ and THC to emission inventories are expected to be insignificant due both to the small emission factors and to the relatively small quantity of fuel consumed by these portable devices. An exposure scenario analysis indicates that every-day use of the kerosene lamp in a village house can generate fine PM exposures easily exceeding the US promulgated NAAQS for PM_2.5.     

Real-world emission factors of fifteen carbonyl compounds measured in a Hong Kong tunnel

Real-world vehicle emissions of carbonyls were determined in summer and winter of 2003 at the Shing Mun Tunnel, Hong Kong. Fifteen carbonyl species have been analyzed in this study. The total measured carbonyls emission factors ranged from 21.7 to 68.9 mg veh⁻¹ km⁻¹ among different measurement periods, with an average of 35.8±11.9 mg veh⁻¹ km⁻¹. Higher carbonyl emissions were found to be associated with a high proportion of diesel-fueled vehicles. Total measured carbonyl emissions from Diesel-fueled Vehicle (DV, 71.5 mg veh⁻¹ km⁻¹) were about 7 times higher than those from Non-Diesel-fueled Vehicle (NDV, 10 mg veh⁻¹ km⁻¹). The five carbonyls with the largest DV emission factor were, in decreasing order, formaldehyde (38.3 mg veh⁻¹ km⁻¹), acetaldehyde (11.4 mg veh⁻¹ km⁻¹), acetone (5.3 mg veh⁻¹ km⁻¹), crotonaldehyde (5.2 mg veh⁻¹ km⁻¹) and benzaldehyde (2.0 mg veh⁻¹ km⁻¹). These five carbonyl compounds together accounted for 87% of the sum of all DV carbonyl emission factors. For NDV, the five most abundant carbonyls in NDV emission at the tunnel were, in decreasing order, formaldehyde (3.5 mg veh⁻¹ km⁻¹), acetone (1.8 mg veh⁻¹ km⁻¹), methyl ethyl ketone (1.6 mg veh⁻¹ km⁻¹), m,p-tolualdehyde (1.0 mg veh⁻¹ km⁻¹) and acetaldehyde (mg veh⁻¹ km⁻¹). They accounted for 85% of the sum of all NDV carbonyl emission factors.     

Effects of aqueous stable fullerene nanocrystals (nC60) on Daphnia magna: Evaluation of sub-lethal reproductive responses and accumulation

Concerns exist regarding the inadvertent release of engineered nanomaterials into natural systems, and the possible negative ecosystem response that may occur. Understanding sub-lethal effects may be particularly important to determining ecosystem responses as current levels of nanomaterial release are low compared to levels projected for the future. In this work, the sub-lethal effects and bioaccumulation of water stable, nanocrystalline fullerenes as C₆₀, (termed nC₆₀) were studied in Daphnia magna, a globally distributed, parthenogenetic zooplankton. Sub-lethal concentrations were first determined for both mature mother (LD₅₀ = 0.4 mg L⁻¹) and neonate (gestating) daphnids (0.2 mg L⁻¹) in standard 48 h exposure tests. Subsequent experiments focused on the accumulation and effects (at temperatures of 18–28 °C) of nC₆₀, during the D. magna reproductive cycle. The results demonstrate that upon sub-lethal exposure, the mortality rates of gestating daphnids increased with time and developmental stage. The maturation of daughter daphnids was negatively impacted. The mother daphnids were unable to reproduce again after exposure during pregnancy, and differential bioaccumulation occurred as a function of lipid content in the daphnia with the highest accumulation level of 7000 mg kg⁻¹ wet weight. Taken together, these results not only describe the accumulation and sub-lethal effects of nC₆₀ on exposed daphnia, but also highlight the importance of sub-lethal exposure scenarios, which are critical to fully understanding the potential impact of fullerenes and other engineered nanoscale materials on natural systems.     

Comparison of carbonyl compounds emissions from diesel engine fueled with biodiesel and diesel

The characteristics of carbonyl compounds emissions were investigated on a direct injection, turbocharged diesel engine fueled with pure biodiesel derived from soybean oil. The gas-phase carbonyls were collected by 2,4-dinitrophenylhydrazine (DNPH)-coated silica cartridges from diluted exhaust and analyzed by HPLC with UV detector. A commercial standard mixture including 14 carbonyl compounds was used for quantitative analysis. The experimental results indicate that biodiesel-fueled engine almost has triple carbonyls emissions of diesel-fueled engine. The weighted carbonyls emission of 8-mode test cycle of biodiesel is 90.8 mg (kW h)^?1 and that of diesel is 30.7 mg (kW h)^?1. The formaldehyde is the most abundant compound of carbonyls for both biodiesel and diesel, taking part for 46.2% and 62.7% respectively. The next most significant compounds are acetaldehyde, acrolein and acetone for both fuels. The engine fueled with biodiesel emits a comparatively high content of propionaldehyde and methacrolein. Biodiesel, as an alternative fuel, has lower specific reactivity (SR) caused by carbonyls compared with diesel. When fueled with biodiesel, carbonyl compounds make more contribution to total hydrocarbon emission.     

Air pollutants in rural homes in Guizhou,China – Concentrations,speciation, and size distribution

Several types of fuels, including coal, fuel wood, and biogas, are commonly used for cooking and heating in Chinese rural households, resulting in indoor air pollution and causing severe health impacts. In this paper, we report a study monitoring multiple pollutants including PM₁₀, PM_2.5, CO, CO₂, and volatile organic compounds (VOCs) from fuel combustion at households in Guizhou province of China. The results showed that most pollutants exhibited large variability for different type of fuels except for CO₂. Among these fuels, wood combustion caused the most serious indoor air pollution, with the highest concentrations of particulate matters (218～417 μg m^?3 for PM₁₀ and 201～304 μg m^?3 for PM_2.5), and higher concentrations of CO (10.8 ± 0.8 mg m^?3) and TVOC (about 466.7 ± 337.9 μg m^?3). Coal combustion also resulted in higher concentrations of particulate matters (220～250 μg m^?3 for PM₁₀ and 170～200 μg m^?3 for PM_2.5), but different levels for CO (respectively 14.5 ± 3.7 mg m^?3 for combustion in brick stove and 5.5 ± 0.7 mg m^?3 for combustion in metal stove) and TVOC (170 mg m^?3 for combustion in brick stove and 700 mg m^?3 for combustion in metal stove). Biogas was the cleanest fuel, which brought about the similar levels of various pollutants with the indoor case of non-combustion, and worth being promoted in more areas. Analysis of the chemical profiles of PM_2.5 indicated that OC and EC were dominant components for all fuels, with the proportions of 30～48%. A high fraction of SO₄^2? (31～34%) was detected for coal combustion. The cumulative percentages of these chemical species were within the range of 0.7～1.3, which was acceptable for the assessment of mass balance.     

Broadband UV spectroscopy system used for monitoring of SO2 and NO emissions from thermal power plants

A gas monitoring system based on broadband absorption spectroscopic techniques in the ultraviolet region is described and tested. The system was employed in real-time continuous concentration measurements of sulfur dioxide (SO₂) and nitric oxide (NO) from a 220-ton h^?1 circulating fluidized bed (CFB) boiler in Shandong province, China. The emission coefficients (per kg of coal and per kWh of electricity) and the total emission of the two pollutant gases were evaluated. The measurement results showed that the emission concentrations of SO₂ and NO from the CFB boiler fluctuated in the range of 750–1300 mg m^?3 and 100–220 mg m^?3, respectively. Compared with the specified emission standards of air pollutants from thermal power plants in China, the values were generally higher for SO₂ and lower for NO. The relatively high emission concentrations of SO₂ were found to mainly depend on the sulfur content of the fuel and the poor desulfurization efficiency. This study indicates that the broadband UV spectroscopy system is suitable for industrial emission monitoring and pollution control.     

Characteristics of carbonyl compounds in public vehicles of Beijing city: Concentrations,sources, and personal exposures

The characteristics of carbonyl compounds (carbonyls) including concentrations, major sources, and personal exposure were investigated for 29 vehicles including taxi, bus and subway in Beijing. It was found that the taxis (Xiali, TA) and buses (Huanghe, BA) fueled by gasoline with longer service years had the higher indoor carbonyl levels (178±42.7 and 188±31.6 μg m⁻³) while subways energized by electricity without exhaust and the jingwa buses (BB) driven in the suburb had the lower levels with total concentrations of 98.5±26.3 and 92.1±20.3 μg m⁻³, respectively. Outdoor carbonyls of taxi cars and buses were nearly at the same level with their total concentrations varying from 80 to 110 μg m⁻³. The level of outdoor subways carbonyls was equal with the ambient air levels. Exhaust leakage, indoor material emissions, photochemical formation, and infiltration of outdoor air were considered to be the major sources to in-vehicle carbonyls. Personal exposures and cancer risk to formaldehyde and acetaldehyde were calculated for professional bus and taxi drivers, respectively. Taxi drivers had the highest cancer risk with personal exposure to formaldehyde and acetaldehyde of 212 and 243 μg day⁻¹, respectively. The public concern should pay considerable attention to professional drivers’ health.     

Preliminary study of the determination of ambient carbonyls in Xalapa City,Veracruz, Mexico

A preliminary study of ambient carbonyls was performed in Xalapa City to measure carbonyls in the atmosphere of this City, because it has an explosive increase in population and traffic density, but few industries. The city is located at the eastern flanks of the Sierra Madre Oriental, between 1350 and 1550 m above sea level. Acetone was the most abundant carbonyl in June, followed by formaldehyde and acetaldehyde, whereas acetaldehyde was the most abundant one in November. Higher concentrations were observed in autumn than in spring, probably due to stagnation conditions in autumn and heavy rains from late spring to early autumn. The very high concentrations of acetaldehyde found in November could have been caused by an accidental leak or spill from a truck, since no stationary sources were identified and acetaldehyde concentrations steeply rose and constantly decreased after few days. Moreover, a highly transited highway traverses Xalapa. The most important ozone and carbon monoxide concentrations were below the Mexican Air Quality Standards; 216 μg m⁻³ (0.11 ppm) for 1 h average and 12.6 mg m⁻³ (11 ppm) for 8 h moving average, respectively. The low concentrations of the main carbonyls, compared with the values reported for other urban areas, and of carbon monoxide, seem to indicate that air quality is still satisfactory in Xalapa City.     

Decadal reductions of traffic emissions on a transit route in Austria – results of the Tauerntunnel experiment 1997

Real-world emissions of a traffic fleet on a transit route in Austria were determined in the Tauerntunnel experiment in October 1997. The total number of vehicles and the average speed was nearly the same on both measuring days (465 vehicles 30 min⁻¹ and 76 km h⁻¹ on the workday, 477 and 78 km h⁻¹ on Sunday). The average workday fleet contained 17.6% heavy-duty vehicles (HDV) and the average Sunday fleet 2.8% HDV resulting in up to four times higher emission rates per vehicle per km on the workday than on Sunday for most of the regulated components (CO₂, CO, NO_x, SO₂, and particulate matter-PM10). Emission rates of NMVOC accounted for 200 mg vehicle⁻¹ km⁻¹ on both days. The relative contributions of light-duty vehicles (LDV) and HDV to the total emissions indicated that aldehydes, BTEX (benzene, toluene, ethylbenzene, xylenes), and alkanes are mainly produced by LDV, while HDV dominated emissions of CO, NO_x, SO₂, and PM10. Emissions of NO_x caused by HDV were 16,100 mg vehicle⁻¹ km⁻¹ (as NO₂). Produced by LDV they were much lower at 360 mg vehicle⁻¹ km⁻¹. Comparing the emission rates to the results that were obtained by the 1988 experiment at the same place significant changes in the emission levels of hydrocarbons and CO, which accounted 1997 to only 10% of the levels in 1988, were noticed. However, the decrease of PM has been modest leading to values of 80 and 60% of the levels in 1988 on the workday and on Sunday, respectively. Emission rates of NO_x determined on the workday in 1997 were 3130 mg vehicle⁻¹ km⁻¹ and even higher than in 1988 (2630 mg vehicle⁻¹ km⁻¹), presumable due to the increase of the HD-traffic.     

Spatial and chemical patterns of PM10 in road dust deposited in urban environment

Recent research interest has been focused on road dust resuspension as one of the major sources of atmospheric particulate matter in an urban environment. Given the dearth of studies on the variability of the PM₁₀ fraction of road deposited sediments, our understanding of the main factors controlling this pollutant is incomplete. In the present study a new sampling methodology was devised and applied to collect PM₁₀ deposited mass from 1 m² of road pavement. PM₁₀ road dust fraction was sampled directly from active traffic lanes at 23 sampling sites during a campaign in Barcelona (Spain) in June 2007. The aim of the study was to gain more insight into the variability of mass and chemistry of road dust in different urban environments, such as the city centre, ring roads, and locations nearby demolition/construction sites. The city centre showed values of PM₁₀ road dust within a range of 3–23 mg m^?2, whereas levels reached 24–80 mg m^?2 in locations affected by transport of uncovered heavy trucks. The largest dust loads were measured in the proximity of demolition/construction sites and the harbor entry with values up to 328 mg m^?2.The city centre road dust profiles (%) were enriched in OC, EC, Fe, S, Cu, Zn, Mn, Cr, Sb, Sn, Mo, Zr, Hf, Ge, Ba, Pb, Bi, SO₄^2?, NO₃^?, Cl^? and NH₄⁺, but several crustal components such as Ca, Ti, Na, and Mg were also considerably concentrated. Locations affected by construction and demolition activities had high levels of crustal components such as Ca, Li, Sc, Sr, Rb and also As whereas ring roads, characterized by a higher load of uncovered heavy trucks showed an intermediate composition.Levels of PM₁₀ components per area were also evaluated to quantify the resuspendable amount of each element from 1 m². In the inner city environment mean values of 1363 μg Ca m^?2, 816 μg OC m^?2, 239 μg EC m^?2, 13 μg Cu m^?2, 12 μg Zn m^?2, 1.9 μg Sb m^?2 and 2.0 μg Pb m^?2, in PM₁₀ in all cases, were registered.Moreover the deposited PM load at demolition/construction sites acts as a reservoir or trap for traffic-related particles, which gives rise to large amounts of hazardous pollutants, available for resuspension.     

Fire and biofuel contributions to annual mean aerosol mass concentrations in the United States

We estimate the contributions from biomass burning (summer wildfires, other fires, residential biofuel, and industrial biofuel) to seasonal and annual aerosol concentrations in the United States. Our approach is to use total carbonaceous (TC) and non-soil potassium (ns-K) aerosol mass concentrations for 2001–2004 from the nationwide IMPROVE network of surface sites, together with satellite fire data. We find that summer wildfires largely drive the observed interannual variability of TC aerosol concentrations in the United States. TC/ns-K mass enhancement ratios from fires range from 10 for grassland and shrub fires in the south to 130 for forest fires in the north. The resulting summer wildfire contributions to annual TC aerosol concentrations for 2001–2004 are 0.26 μg C m⁻³ in the west and 0.14 μg C m⁻³ in the east; Canadian fires are a major contributor in the east. Non-summer wildfires and prescribed burns contribute on an annual mean basis 0.27 and 0.31 μg C m⁻³ in the west and the east, highest in the southeast because of prescribed burning. Residential biofuel is a large contributor in the northeast with annual mean concentration of up to 2.2 μg C m⁻³ in Maine. Industrial biofuel (mainly paper and pulp mills) contributes up to 0.3 μg C m⁻³ in the southeast. Total annual mean fine aerosol concentrations from biomass burning average 1.2 and 1.6 μg m⁻³ in the west and east, respectively, contributing about 50% of observed annual mean TC concentrations in both regions and accounting for 30% (west) and 20% (east) of total observed fine aerosol concentrations. Our analysis supports bottom-up source estimates for the contiguous United States of 0.7–0.9 Tg C yr⁻¹ from open fires (climatological) and 0.4 Tg C yr⁻¹ from biofuel use. Biomass burning is thus an important contributor to US air quality degradation, which is likely to grow in the future.     

Long-term measurements of SO2 dry deposition over Gansu Province,China

Potassium carbonate sulfation plates, monitored monthly for 11 years from 48 sites in 11 cities in Gansu Province, China, provide a crude estimate of cumulative SO₂ dry depositions. Measured SO₂ dry deposition rates were 1.6–472 mg m⁻² day⁻¹ and had seasonal variations with maxima in winter and minima mainly during summer as a result of higher winter and lower summer SO₂ concentrations. The 11-year monthly average SO₂ dry deposition rates are 23.2–248.97 and 11.7–175.6 mg m⁻² day⁻¹ in the eleven cities in winter and summer, respectively. A monthly average SO₂ deposition velocity was also estimated from 0.06 to 9.72 cm s⁻² in the 11 cities studied with a 11-year average maximum value of about 1.1–2.7 cm s⁻² in April and July and a 11-year average minimum value of about 0.2–1.0 cm s⁻¹ in January. The SO₂ dry deposition velocity also exhibits an increasing with wind speed in basins of less than 500 mm annual precipitation. In contrast, due to influences of the relative humidity in valleys of more than 500 mm annual precipitation, it shows a decreasing trend with wind speed increasing.     

Trends of ambient carbonyl compounds in the urban environment of Hong Kong

The concentrations of C₁–C₈ carbonyl compounds were measured at two urban sites in Hong Kong from October 1997 to September 2000. The daily total carbonyl concentrations were found to range from 2.4 to 37 μg m⁻³. Formaldehyde was the most abundant species, which comprised from 36 to 43% of the total detected carbonyls, followed by acetaldehyde (18–21%) and acetone (8–20%). The highest 24-hour average concentrations measured were 10 and 7.7 μg m⁻³ for formaldehyde and acetaldehyde, respectively. Seasonal and temporal variations in the concentrations of formaldehyde and acetaldehyde were not obvious, but lowest concentrations often occurred from June to August. The mean formaldehyde/acetaldehyde molar ratios at the two sites in summer (2.8±1.1 and 2.5±1.2) were significantly higher (p⩽0.01) than those in winter periods (1.9±0.6 and 2.0±0.6). The phenomena were explained by influences of both photochemical reactions and local meteorological conditions. Better correlations between formaldehyde and acetaldehyde, and between NO_x and each of the two major carbonyls were obtained in winter periods indicating direct vehicular emissions were the principal sources. The ambient formaldehyde and acetaldehyde concentrations in the urban atmosphere of Hong Kong were within the normal ranges reported in the literature for other urban sites world-wide.     

Preparation of controlled nano-MgO and investigation of its bactericidal properties

Nano-MgO is a good bactericide but with strong alkalinity in water due to its rapid hydrolysis. To control its hydrolysis rate and keep its bactericidal properties, we synthesized nano-MgO microspheres using chitosan–alginate system in this study. The synthesized nano-MgO release-controlled microspheres (nMgO-RCM) were with 0.98–1.20 mm of particle sizes. Also, their embedding ratio and loading percentage was 63.52% and 12.27%, respectively. Based on the characterization results, nano-MgO was only observed on surface of the nMgO-RCM. Its release rate from the nMgO-RCM could be controlled by the chitosan–alginate system, and the observed rate constant (k_obs) increased from 0.0289 h⁻¹ to 0.0358 h⁻¹ with the increment of the dosage from 10 mg L⁻¹ to 80 mg L⁻¹. Furthermore, the nMgO-RCM could maintain pH value lower than 8.5 and colony counts less than 20 CFU mL⁻¹ for at least 120 h.     

Accumulation pattern of Dechlorane Plus and associated biological effects on rats after 90 d of exposure

Recent studies have indicated that Dechlorane Plus (DP) is widespread in the environments. However, different isomer-specific enrichment pattern of syn-DP and anti-DP was reported in biological samples from the field. In this study, Sprague–Dawley rats were consecutively exposed to commercial DP 25 by gavage for 90 d at different doses (0, 1, 10, and 100 mg kg^?1 d^?1) to investigate the accumulation pattern of syn-DP and anti-DP in liver, muscle, and serum of rats. The possible biological effects of DP on rats were also examined. Results showed that DP preferentially accumulated in the liver rather than in muscle at all exposure levels. No significant stereoselectivity of anti-DP or syn-DP in tissues was observed in the low DP exposure groups (0 and 1 mg kg^?1 d^?1) with f_anti values (defined as the concentration of the anti-DP divided by the sum of concentrations of anti- and syn-DP) ranging from 0.74 to 0.78. However, f_anti values reduced (f_anti ranged from 0.26 to 0.30) significantly in the high DP exposure groups (10 and 100 mg kg^?1 d^?1) and syn-DP was predominant in all tissues. Biochemical parameters in serum, the mRNA expression levels of certain enzymes and their activities in liver were detected. There was no observable-effect in histopathology and death during the experiment, although the mRNA expression levels of some genes in the low dosage group decreased significantly and enzyme activity of CYP 2B2 increased.     

Kinetic aspects and identification of by-products during the ozonation of bitertanol in agricultural wastewaters

The degradation of bitertanol by ozone treatment is investigated. Solutions of bitertanol (8.4 μg mL^?1) were prepared either by dissolution of the standard or by dilution of Gaucho Blé seed loading solution and then ozonated under different conditions. Evolution of the concentrations of bitertanol and its ozonation by-products in both solutions was monitored by HPLC–UV as a function of the treatment time for a concentration of 100 g m^?3 of ozone in the inlet gas. Bitertanol degradation was found to follow a pseudo-first order reaction in both cases. However, the rate of the reaction in diluted seed loading solution was much lower (0.19 vs. 0.27 min^?1 in standard solution) and was close to the reaction rate observed in the presence of a radical scavenger, tert-butanol (0.11 min^?1). Thus, it may be suggested that additives present in the seed loading solution may play the role of radical scavengers. Study of ozone concentration in the inlet gas (from 25 to 100 g m^?3) showed that ozone degradation is also a first-order reaction with respect to ozone. Four ozonation by-products were highlighted, collected and identified by HPLC coupled with an ion trap mass spectrometer using positive electrospray ionization mode. A degradation pathway of bitertanol was finally proposed.