Measurement of particulate concentrations produced during bulk material handling at the Tarragona harbor

Bulk material handling can be a significant source of particles in harbor areas. The atmospheric impact of a number of loading/unloading activities of diverse raw materials has been assessed from continuous measurements of ambient particle concentrations recorded close to the emission sources. Two experimental campaigns have been carried out in the Tarragona port to document the impact of specific handling operations and bulk materials. Dusty bulk materials such as silica–manganese powder, tapioca, coal, clinker and lucerne were dealt with during the experiments. The highest impacts on ambient particle concentrations were recorded during handling of clinker. For this material and silica–manganese powder, high concentrations were recorded in the fine grain size (<2.5 μm). The lowest impacts on particulate matter concentrations were recorded during handling of tapioca and lucerne, mainly in the coarse grain size (2–5–10 μm). The effectiveness of several emission abatement measures, such as ground watering to diminish coal particle resuspension, was demonstrated to reduce ambient concentrations by up to two orders of magnitude. The importance of other good practices in specific handling operations, such as controlling the height of the shovel discharge, was also evidenced by these experiments. The results obtained can be further utilized as a useful experimental database for emission factor estimations.     

Soil Suspension/Dispersion Modeling Methods for Estimating Health-Based Soil Cleanup Levels of Hexavalent Chromium at Chromite Ore Processing Residue Sites

Abstract

The primary health concern associated with exposures to chromite ore processing residue (COPR)-affected soils is inhalation of hexavalent chromium [Cr(VI)] particulates. Site-specific soil alternative remediation standards (ARSs) are set using soil suspension and dispersion models to be protective of the theoretical excess cancer risk associated with inhalation of soil suspended by vehicle traffic and wind. The purpose of this study was to update a previous model comparison study that identified the 1995 AP-42 particulate emission model for vehicle traffic over un-paved roads and the Fugitive Dust Model (FDM) as the most appropriate model combination for estimating site-specific ARSs. Because the AP-42 model has been revised, we have updated our past evaluation. Specifically, the 2006 AP-42 particulate emissions model; the Industrial Source Complex–Short Term model, version 3 (ISCST3); and the American Meteorological Society/Environmental Protection Agency Regulatory Model (AERMOD) air dispersion models were evaluated, and the results were compared with those from the previously used modeling approaches. Two sites with and two sites without vehicle traffic were evaluated to determine if wind erosion is a significant source of emissions. For the two sites with vehicle traffic, both FDM and ISCST3 produced total suspended particulate (TSP) estimates that were, on average, within a factor of 2 of measured; whereas AERMOD produced estimates that were as much as 5-fold higher than measured. In general, the estimated TSP concentrations for FDM were higher than those for ISCST3. For airborne Cr(VI), the ISCST3 model produced estimates that were only 2- to 8-fold of the measured concentrations, and both FDM and AERMOD estimated airborne Cr(VI) concentrations that were approximately 4- to 14-fold higher than measured. Results using the 1995 AP-42 model were closer to measured than those from the 2006 AP-42 model. Wind erosion was an insignificant contributor to particulate emissions at COPR sites.     

Soil suspension/dispersion modeling methods for estimating health-based soil cleanup levels of hexavalent chromium at chromite ore processing residue sites

The primary health concern associated with exposures to chromite ore processing residue (COPR)-affected soils is inhalation of hexavalent chromium [Cr(VI)] particulates. Site-specific soil alternative remediation standards (ARSs) are set using soil suspension and dispersion models to be protective of the theoretical excess cancer risk associated with inhalation of soil suspended by vehicle traffic and wind. The purpose of this study was to update a previous model comparison study that identified the 1995 AP-42 particulate emission model for vehicle traffic over unpaved roads and the Fugitive Dust Model (FDM) as the most appropriate model combination for estimating site-specific ARSs. Because the AP-42 model has been revised, we have updated our past evaluation. Specifically, the 2006 AP-42 particulate emissions model; the Industrial Source Complex-Short Term model, version 3 (ISCST3); and the American Meteorological Society/Environmental Protection Agency Regulatory Model (AERMOD) air dispersion models were evaluated, and the results were compared with those from the previously used modeling approaches. Two sites with and two sites without vehicle traffic were evaluated to determine if wind erosion is a significant source of emissions. For the two sites with vehicle traffic, both FDM and ISCST3 produced total suspended particulate (TSP) estimates that were, on average, within a factor of 2 of measured; whereas AERMOD produced estimates that were as much as 5-fold higher than measured. In general, the estimated TSP concentrations for FDM were higher than those for ISCST3. For airborne Cr(VI), the ISCST3 model produced estimates that were only 2- to 8-fold of the measured concentrations, and both FDM and AERMOD estimated airborne Cr(VI) concentrations that were approximately 4- to 14-fold higher than measured. Results using the 1995 AP-42 model were closer to measured than those from the 2006 AP-42 model. Wind erosion was an insignificant contributor to particulate emissions at COPR sites.     

Characterization of spatial impact of particles emitted from a cement material production facility on outdoor particle deposition in the surrounding community

The objective of this study was to estimate the contribution of a facility that processes steel production slag into raw material for cement production to local outdoor particle deposition in Camden, NJ. A dry deposition sampler that can house four 37-mm quartz fiber filters was developed and used for the collection of atmospheric particle deposits. Two rounds of particle collection (3-4 weeks each) were conducted in 8-11 locations 200-800 m downwind of the facility. Background samples were concurrently collected in a remote area located -2 km upwind from the facility. In addition, duplicate surface wipe samples were collected side-by-side from each of the 13 locations within the same sampling area during the first deposition sampling period. One composite source material sample was also collected from a pile stored in the facility. Both the bulk of the source material and the < 38 microm fraction subsample were analyzed to obtain the elemental source profile. The particle deposition flux in the study area was higher (24-83 mg/m2 x day) than at the background sites (13-17 mg/m2day). The concentration of Ca, a major element in the cement source production material, was found to exponentially decrease with increasing downwind distance from the facility (P < 0.05). The ratio of Ca/Al, an indicator of Ca enrichment due to anthropogenic sources in a given sample, showed a similar trend. These observations suggest a significant contribution of the facility to the local particle deposition. The contribution of the facility to outdoor deposited particle mass was further estimated by three independent models using the measurements obtained from this study. The estimated contributions to particle deposition in the study area were 1.8-7.4% from the regression analysis of the Ca concentration in particle deposition samples against the distance from the facility, 0-11% from the U.S. Environmental Protection Agency (EPA) Chemical Mass Balance (CMB) source-receptor model, and 7.6-13% from the EPA Industrial Source Complex Short Term (ISCST3) dispersion model using the particle-size-adjusted permit-based emissions estimates.     

Evaluation of pollution prevention options to reduce styrene emissions from fiber-reinforced plastic open molding processes

Pollution prevention (P2) options to reduce styrene emissions, such as new materials and application equipment, are commercially available to the operators of open molding processes. However, information is lacking on the emissions reduction that these options can achieve. To meet this need, the U.S. Environmental Protection Agency's (EPA) Air Pollution Prevention and Control Division, working in collaboration with Research Triangle Institute, measured styrene emissions for several of these P2 options. In addition, the emission factors calculated from these test results were compared with the existing EPA emission factors for gel coat sprayup and resin applications. Results show that styrene emissions can be reduced by up to 52% by using controlled spraying (i.e., reducing overspray), low-styrene and styrene-suppressed materials, and nonatomizing application equipment. Also, calculated emission factors were 1.6-2.5 times greater than the mid-range EPA emission factors for the corresponding gel coat and resin application. These results indicate that facilities using existing EPA emission factors to estimate emissions in open molding processes are likely to underestimate actual emissions. Facilities should investigate the applicability and feasibility of these P2 options to reduce their styrene emissions.     

Emission Factors for Gasoline Light-Duty Vehicles: Experimental Program in Santiago,Chile

ABSTRACT

The emission inventory of the city of Santiago, Chile, related to mobile sources was built up using constant emission factors extracted from international literature. To improve the estimate of mobile source emissions, an experimental program was designed, consisting of transient tests on a chassis dynamometer over a sample of about 166 vehicles, applying 9 local driving cycles with average speeds of 3-80 km/hr, and experimentally determined in previous research carried out by the authors. An analysis of the influence of fuel inlet technology, and a year time-length model over emissions, was undertaken. We proposed emission factors as a function of average speed and of CO, THC, and NO_x for catalytic and noncatalytic light-duty gasoline vehicles, disaggregated on commercial and private cars. A comparative analysis with emission factors obtained for the application of the COPERT II and AP-42 models was also presented. Our current analysis gives solid evidence indicating that to obtain a reasonable accuracy on emission estimates and calculations, local emission factors must be used.     

Evaluating Sources of Indoor Air Pollution

Evaluation of Indoor air pollution problems requires an understanding of the relationship between sources, air movement, and outdoor air exchange. Research is underway to investigate these relationships. A three-phase program is being implemented: 1) Environmental chambers are used to provide source emission factors for specific indoor pollutants; 2) An IAQ (Indoor Air Quality) model has been developed to calculate indoor pollutant concentrations based on chamber emissions data and the air exchange and air movement within the indoor environment; and 3) An IAQ test house is used to conduct experiments to evaluate the model results. Examples are provided to show how this coordinated approach can be used to evaluate specific sources of indoor air pollution. Two sources are examined: 1) para-dichlorobenzene emissions from solid moth repellant; and 2) particle emissions from unvented kerosene heaters.

The evaluation process for both sources followed the three-phase approach discussed above. Para-dichlorobenzene emission factors were determined by small chamber testing at EPA’s Air and Energy Engineering Research Laboratory. Particle emission factors for the kerosene heaters were developed In large chambers at the J. B. Pierce Foundation Laboratory. Both sources were subsequently evaluated in EPA’s IAQ test house. The IAQ model predictions showed good agreement with the test house measurements when appropriate values were provided for source emissions, outside air exchange, in-house air movement, and deposition on “sink” surfaces.     

Use of Subsampled Traffic Data to Estimate Roadway Emissions,Including Conversion to MOBILE6 Vehicle Classifications

Abstract

Air quality is degraded by many factors, among which the emissions from on‐road vehicles play a significant role. Timely and accurate estimate of such emissions becomes very important for policy‐making and effective control measures. However, lack of traffic data and outdated emission software make this task difficult. This research has demonstrated a new method that facilitates the vehicular emission inventories at the local level by using shorter-time Highway Performance Monitoring System (HPMS) traffic data along with the latest U.S. Environment Protection Agency (EPA) emission modeling software, MOBILE6. The conversion methodology was developed for converting readily available HPMS traffic volume data into EPA MOBILE-based traffic classifications, and a corresponding software program was written for automating the process. EPA MOBILE6 model was used to obtain emissions of nitrogen oxides (NO_x), volatile organic compound (VOC), and cabon monoxide (CO) emitted by the parent traffic and subsampled traffic data, and these emissions were additionally compared. The case study has shown that the difference of the magnitude between the emission estimates produced by certain subsampled and parent traffic data are minor, indicating that subsampled HPMS data can be used for reporting parent traffic emissions. It was also observed that traffic emissions follow a Weibull distribution, and NO_x emissions were more sensitive to the traffic data composition than VOC and CO. Lastly, use of average emission values of 20 or 30 consecutive minutes appears to be valid for representing hourly emissions.     

Emission factors for gasoline light-duty vehicles: experimental program in Santiago, Chile

The emission inventory of the city of Santiago, Chile, related to mobile sources was built up using constant emission factors extracted from international literature. To improve the estimate of mobile source emissions, an experimental program was designed, consisting of transient tests on a chassis dynamometer over a sample of about 166 vehicles, applying 9 local driving cycles with average speeds of 3-80 km/hr, and experimentally determined in previous research carried out by the authors. An analysis of the influence of fuel inlet technology, and a year time-length model over emissions, was undertaken. We proposed emission factors as a function of average speed and of CO, THC, and NOx for catalytic and noncatalytic light-duty gasoline vehicles, disaggregated on commercial and private cars. A comparative analysis with emission factors obtained for the application of the COPERT II and AP-42 models was also presented. Our current analysis gives solid evidence indicating that to obtain a reasonable accuracy on emission estimates and calculations, local emission factors must be used.     

Quantification of emission factor uncertainty

Emissions factors are important for estimating and characterizing emissions from sources of air pollution. There is no quantitative indication of uncertainty for these emission factors, most factors do not have an adequate data set to compute uncertainty, and it is very difficult to locate the data for those that do. The objectives are to compare the current emission factors of Electric Generating Unit NOx sources with currently available continuous emission monitoring data, develop quantitative uncertainty indicators for the Environmental Protection Agency (EPA) data quality rated emission factors, and determine the possible ranges of uncertainty associated with EPA's data quality rating of emission factors. EPA's data letter rating represents a general indication of the robustness of the emission factor and is assigned based on the estimated reliability of the tests used to develop the factor and on the quantity and representativeness of the data. Different sources and pollutants that have the same robustness in the measured emission factor and in the representativeness of the measured values are assumed to have a similar quantifiable uncertainty. For the purposes of comparison, we assume that the emission factor estimates from source categories with the same letter rating have enough robustness and consistency that we can quantify the uncertainty of these common emission factors based on the qualitative indication of data quality which is known for almost all factors. The results showed that EPA's current emission factor values for NOx emissions from combustion sources were found to be reasonably representative for some sources; however AP-42 values should be updated for over half of the sources to reflect current data. The quantified uncertainty ranges were found to be 25-62% for A rated emission factors, 45-75% for B rated emission factors, 60-82% for C rated emission factors, and 69-86% for D rated emission factors, and 82-92% for E rated emission factors.     

An incinerator air quality impact assessment for metals, PAH, dioxins and furans by using the MM5-CMAQ-EMIMO atmospheric modelling system: Spain case study

In this paper, we show the implementation of a modified version of MM5-CMAQ for carrying out an air quality impact analysis for installing an incinerator in the Basque Country model domain (Spain). The modified CMAQ model (EPA USA, 2004) includes Poly-Chlorinated Dibenzop-Dioxins and Dibenzo-Furans (dioxins and furans). This model represents their congeners as divided between gaseous and aerosol forms that exchange mass based on theoretical coefficients for gas to particle portioning. The emission model EMIMO – developed by UPM – has been adapted to incorporate the three metals and the benzo(a)pyrene according to the EMEP annual emission inventory. In addition, the PCDD/F EMEP emission inventory has been incorporated into the EMIMO model to produce proper 1 hr and 1 km × 1 km emission PCDD/F estimation. The emissions of the projected incinerator are incorporated by using the chimney technical parameters and the limit emission values (worst-case scenario) prescribed in the Directive/2000/76/CE.     

Use of subsampled traffic data to estimate roadway emissions, including conversion to MOBILE6 vehicle classifications

Air quality is degraded by many factors, among which the emissions from on-road vehicles play a significant role. Timely and accurate estimate of such emissions becomes very important for policy-making and effective control measures. However, lack of traffic data and outdated emission software make this task difficult. This research has demonstrated a new method that facilitates the vehicular emission inventories at the local level by using shorter-time Highway Performance Monitoring System (HPMS) traffic data along with the latest U.S. Environment Protection Agency (EPA) emission modeling software, MOBILE6. The conversion methodology was developed for converting readily available HPMS traffic volume data into EPA MOBILE-based traffic classifications, and a corresponding software program was written for automating the process. EPA MOBILE6 model was used to obtain emissions of nitrogen oxides (NOx), volatile organic compound (VOC), and cabon monoxide (CO) emitted by the parent traffic and subsampled traffic data, and these emissions were additionally compared. The case study has shown that the difference of the magnitude between the emission estimates produced by certain subsampled and parent traffic data are minor, indicating that subsampled HPMS data can be used for reporting parent traffic emissions. It was also observed that traffic emissions follow a Weibull distribution, and NOx emissions were more sensitive to the traffic data composition than VOC and CO. Lastly, use of average emission values of 20 or 30 consecutive minutes appears to be valid for representing hourly emissions.     

Participate and Gaseous Emissions from Natural Gas Furnaces and Water Heaters

Three furnaces and one hot water heater were tested for particulate and gaseous emissions. The effects of fuel, stoichiometry, operating conditions, and appliance type on emission levels were studied. The filterable particulate levels from a properly operating furnace were very low. However, condensable particulate emissions were considerably greater, approximately the same as predicted by EPA estimates of furnace particulate emissions. Carbon emissions comprised about 12% of filterable particulate emissions. However, when operated highly fuel-rich, copious amounts of elemental carbon particles were emitted with a mass median diameter of less than 0.4 μm. Gaseous emissions were dependent on cycling of the furnace and stoichiometry.

An estimate was made of the daily furnace emissions compared to daily emissions from a 1980 catalyst-equipped automobile. While gaseous emissions were less than the corresponding vehicle emissions, the particle emissions from the furnace were three times greater than particle emissions from a 1980 vehicle.     

Revised estimates of construction activity and emissions: Effects on ozone and elemental carbon concentrations in southern California

Emissions from diesel-powered construction equipment are an important source of nitrogen oxides (NO_x) and particulate matter (PM). A new emission inventory for construction equipment emissions is developed based on surveys of diesel fuel use; the revised inventory is compared to current emission inventories. California's OFFROAD model estimates are 4.5 and 3.1 times greater, for NO_x and PM respectively, than the fuel-based estimates developed here. The most relevant uncertainties are the overall amount of construction activity/diesel fuel use, exhaust emission factors for PM and NO_x, and the spatial allocation of emissions to county level and finer spatial scales. Construction permit data were used in this study to estimate spatial distributions of emissions; the resulting distribution is well correlated with population growth. An air quality model was used to assess the impacts of revised emission estimates. Increases of up to 15 ppb in predicted peak ozone concentrations were found in southern California. Elemental carbon and fine particle mass concentrations were in better agreement with observations using revised emission estimates, whereas negative bias in predictions of ambient NO_x concentrations increased.     

Establishment of a database of emission factors for atmospheric pollutants from Chinese coal-fired power plants

Field measurements and data investigations were conducted for developing an emission factor database for inventories of atmospheric pollutants from Chinese coal-fired power plants. Gaseous pollutants and particulate matter (PM) of different size fractions were measured using a gas analyzer and an electric low-pressure impactor (ELPI), respectively, for ten units in eight coal-fired power plants across the country. Combining results of field tests and literature surveys, emission factors with 95% confidence intervals (CIs) were calculated by boiler type, fuel quality, and emission control devices using bootstrap and Monte Carlo simulations. The emission factor of uncontrolled SO₂ from pulverized combustion (PC) boilers burning bituminous or anthracite coal was estimated to be 18.0S kg t^?1 (i.e., 18.0 × the percentage sulfur content of coal, S) with a 95% CI of 17.2S–18.5S. NO_X emission factors for pulverized-coal boilers ranged from 4.0 to 11.2 kg t^?1, with uncertainties of 14–45% for different unit types. The emission factors of uncontrolled PM_2.5, PM₁₀, and total PM emitted by PC boilers were estimated to be 0.4A (where A is the percentage ash content of coal), 1.5A and 6.9A kg t^?1, respectively, with 95% CIs of 0.3A–0.5A, 1.1A–1.9A and 5.8A–7.9A. The analogous PM values for emissions with electrostatic precipitator (ESP) controls were 0.032A (95% CI: 0.021A–0.046A), 0.065A (0.039A–0.092A) and 0.094A (0.0656A–0.132A) kg t^?1, and 0.0147A (0.0092–0.0225A), 0.0210A (0.0129A–0.0317A), and 0.0231A (0.0142A–0.0348A) for those with both ESP and wet flue-gas desulfurization (wet-FGD). SO₂ and NO_X emission factors for Chinese power plants were smaller than those of U.S. EPA AP-42 database, due mainly to lower heating values of coals in China. PM emission factors for units with ESP, however, were generally larger than AP-42 values, because of poorer removal efficiencies of Chinese dust collectors. For units with advanced emission control technologies, more field measurements are needed to reduce emission factor uncertainties.     

Derivation of new emission factors for quantification of mass emissions when using optical gas imaging for detecting leaks

This paper describes the development of new "leak/no-leak" emission factors that are suitable for estimating facilities' fugitive emissions when using an alternative work practice (AWP) that is based on optical gas imaging technology for detecting leaking piping system components. These emission factors were derived for valves, pumps, and connectors/flanges for instrument leak detection thresholds ranging from 3 to 60 g/hr using a combination of field data and Monte Carlo statistical simulation techniques. These newly derived leak/no-leak emission factors are designed to replace the U.S. Environment Protection Agency (EPA) 1995 Protocol factors, which were based on Method 21 monitoring of leaks at "uncontrolled" facilities. The emission factors published in the 1995 Protocol have not been updated since the 1970s. This derivation is based on results where the authors document the use of a Monte Carlo simulation technique to quantify the required leak detection thresholds that provide equal--or better--environmental benefits for an AWP. The use of these newly derived emission factors is demonstrated for different methods of computing fugitive emissions from a hypothetical model refinery. The resulting facility emissions calculated by using these new emission factors is compared with the existing emission estimation methods provided in the EPA 1995 Protocol. The results demonstrate that the new emission factors provide an emission estimate that is the closest to that obtained from the direct determination of total emissions by Monte Carlo simulations.     

Emissions of chromium (VI) from arc welding

The presence of Cr in the +6 oxidation state (Cr[VI]) is still observed in ambient air samples in California despite steps taken to reduce emissions from plating operations. One known source of emission of Cr(VI) is welding, especially with high Cr-content materials, such as stainless steels. An experimental effort was undertaken to expand and update Cr(VI) emission factors by conducting tests on four types of arc-welding operations: gas-metal arc welding (GMAW), shielded metal arc welding (SMAW), fluxcore arc welding, and pulsed GMAW. Standard American Welding Society hood results were compared with a total enclosure method that permitted isokinetic sampling for particle size-cut measurement, as well as total collection of the aerosol. The fraction of Cr(VI) emitted per unit mass of Cr electrode consumed was determined. Consistent with AP-42 data, initial results indicate that a significant fraction of the total Cr in the aerosol is in the +6 oxidation state. The fraction of Cr(VI) and total aerosol mass produced by the different arc welding methods varies with the type of welding process used. Self-shielded electrodes that do not use a shield gas, for example, SMAW, produce greater amounts of Cr(VI) per unit mass of electrode consumed. The formation of Cr(VI) from standard electrode wires used for welding mild steel was below the method detection limit after eliminating an artifact in the analytical method used.     

Characterization of the fugitive particulate emissions from construction mud/dirt carryout

Although the fugitive dust associated with construction mud/dirt carryout can represent a substantial portion of the particulate matter (PM) emissions inventory in nonattainment areas, it has not been well characterized by direct sampling methods. In this paper, a research program is described that directly determined both PM10 and PM2.5 (particles < or =10 and 2.5 microm in classical aerodynamic diameter, respectively) emission factors for mud/dirt carryout from a major construction project located in metropolitan Kansas City, MO. The program also assessed the contribution of automotive emissions to the total PM2.5 burden and determined the baseline emissions from the test road. As part of the study, both time-integrated and continuous exposure-profiling methods were used to assess the PM emissions, including particle size and elemental composition. This research resulted in overall PM10 and PM2.5 emission factors of 6 and 0.2 g/vehicle, respectively. Although PM10 is within the range of prior U.S. Environmental Protection Agency (EPA) guidance, the PM2.5 emission factor is far lower than previous estimates published by EPA. In addition, based on both the particle size and chemical data obtained in the study, a major portion of the PM2.5 emissions appears to be attributable to automotive exhaust from light-duty, gasoline-powered vehicles and not to the fugitive dust associated with reentrained mud/dirt carryout.