Dilution and aerosol dynamics within a diesel car exhaust plume—CFD simulations of on-road measurement conditions

Vehicle particle emissions are studied extensively because of their health effects, contribution to ambient PM levels and possible impact on climate. The aim of this work was to obtain a better understanding of secondary particle formation and growth in a diluting vehicle exhaust plume using 3-d information of simulations together with measurements. Detailed coupled computational fluid dynamics (CFD) and aerosol dynamics simulations have been conducted for H₂SO₄–H₂O and soot particles based on measurements within a vehicle exhaust plume under real conditions on public roads.Turbulent diffusion of soot and nucleation particles is responsible for the measured decrease of number concentrations within the diesel car exhaust plume and decreases coagulation rates. Particle size distribution measurements at 0.45 and 0.9 m distance to the tailpipe indicate a consistent soot mode (particle diameter D_p∼50 nm) at variable operating conditions. Soot mode number concentrations reached up to 10¹³ m⁻³ depending on operating conditions and mixing.For nucleation particles the simulations showed a strong sensitivity to the spatial dilution pattern, related cooling and exhaust H₂SO_4(g). The highest simulated nucleation rates were about 0.05–0.1 m from the axis of the plume. The simulated particle number concentration pattern is in approximate accordance with measured concentrations, along the jet centreline and 0.45 and 0.9 m from the tailpipe. Although the test car was run with ultralow sulphur fuel, high nucleation particle (D_p⩽15 nm) concentrations (>10¹³ m⁻³) were measured under driving conditions of strong acceleration or the combination of high vehicle speed (>140 km h⁻¹) and high engine rotational speed (>3800 revolutions per minute (rpm)).Strong mixing and cooling caused rapid nucleation immediately behind the tailpipe, so that the highest particle number concentrations were recorded at a distance, x=0.45 m behind the tailpipe. The simulated growth of H₂SO₄–H₂O nucleation particles was unrealistically low compared with measurements. The possible role of low and semi-volatile organic components on the growth processes is discussed. Simulations for simplified H₂SO₄–H₂O–octane–gasoil aerosol resulted in sufficient growth of nucleation particles.     

Kinetics of the oxidation of hydrogen sulfite by hydrogen peroxide in aqueous solution:: ionic strength effects and temperature dependence

Conductometry was used to study the kinetics of the oxidation of hydrogen sulfite, HSO⁻₃, by hydrogen peroxide in aqueous non-buffered solution at the low concentration level of 10⁻⁵–10⁻⁶ M, typically found in cloud water. The kinetic data confirm that the rate law reported for the pH range 3–6 at higher concentration levels, rate=k_H·[H⁺]·[HSO⁻₃]·[H₂O₂], is valid at the low concentration level and at low ionic strength I_c. At 298 K and I_c=1.5×10⁻⁴ M, third-order rate constant k_H was found to be k_H=(9.1±0.5)×10⁷ M⁻² s⁻¹. The temperature dependence of k_H led to an activation energy of E_a=29.7±0.9 kJ mol⁻¹. The effect of the ionic strength (adjusted with NaCl) on rate constant k_H was studied in the range I_c=2×10⁻⁴–5.0 M at pH=4.5–5.2 by conductometry and stopped-flow spectrophotometry. The dependence of k_H on I_c can be described with a semi-empirical relationship, which is useful for the purpose of comparison and extrapolation. The kinetic data obtained are critically compared with those reported earlier.     

Observations and modelling of aerosol growth in marine stratocumulus—case study

Airborne measurements of the growth of the marine accumulation mode after multiple cycles through stratocumulus cloud are presented. The nss-sulphate cloud residual mode was log-normal in spectral shape and it’s mode radius was observed to progressively increase in size from 0.78 to 0.94 μm over 155 min of air parcel evolution through the cloudy marine boundary layer. The primary reason for this observed growth was thought to result from aqueous phase oxidation of SO₂ to aerosol sulphate in activated cloud drops. An aqueous phase aerosol–cloud-chemistry model was used to simulate this case study of aerosol growth and was able to closely reproduce the observed growth. The model simulations illustrate that aqueous phase oxidation of SO₂ in cloud droplets was able to provide enough additional sulphate mass to increase the size of activated aerosol. During a typical cloud cycle simulation, ≈4.6 nmoles kg^-1_air (0.44 μg m^-3) of sulphate mass was produced with ≈70% of sulphate production occurring in cloud droplets activated upon sea-salt nuclei and ≈30% occurring upon nss-sulphate nuclei, even though sea-salt nuclei contributed less than 15% to the activated droplet population. The high fraction of nss-sulphate mass internally mixed with sea-salt aerosol suggests that aqueous phase oxidation of SO₂ in cloud droplets activated upon sea-salt nuclei is the dominant nss-sulphate formation mechanism and that sea-salt aerosol provides the primary chemical sink for SO₂ in the cloudy marine boundary layer.     

Radical-driven carbonyl-to-acid conversion and acid degradation in tropospheric aqueous systems studied by CAPRAM

Model studies on the aqueous phase radical-driven processing of carbonyl compounds and acids in clouds and deliquescent particles were performed. The model exposed that aqueous radical conversions of carbonyl compounds and its oxidation products can contribute potentially to the formation of functionalised organic acids. The main identified C₂–C₄ organic gas phase precursors are ethylene glycol, glycolaldehyde, glyoxal, methylglyoxal and 1,4-butenedial. The aqueous phase is shown to contribute significantly with about 93%/63%, 47%/8%, 31%/4%, 7%/4%, 36%/8% to the multiphase oxidative fate of these compounds under remote/urban conditions. Interestingly, the studies revealed that aqueous chemical processing is not only limited to in-cloud conditions but also proceeds in deliquescent particle phase with significant fluxes. Oxalic acid is shown to be formed preferably in deliquescent particles subsequent to the in-cloud oxidations. Mean aqueous phase oxalate formation fluxes of about 12, 42 and 0.4 ng m^?3 h^?1 in the remote, urban and maritime scenario, respectively. Additionally, the turnovers of the oxidation of organics such as methylglyoxal by NO₃ radical reactions are identified to be competitive to their OH pendants. At the current state of CAPRAM, mean C₂–C₄ in-cloud oxidation fluxes of about 0.12 and 0.5 μg m^?3 h^?1 are modelled under the idealised remote and urban cloud conditions.Finally, turnovers from radical oxidations were compared with those of thermal reactions. It is demonstrated that, based on the sparse kinetic data available organic accretion reaction might be of interest in just a few cases for cloud droplets and aqueous particles but generally do not reach the oxidative conversion rates of the main radical oxidants OH and NO₃. Interestingly, oxidation reactions of H₂O₂ are shown to be competitive to the OH radical conversions in cases when H₂O₂ is not readily used up by the S(IV) oxidation.     

Characteristics and provenance of dustfall during an unusual floating dust event

This study aims to investigate the characteristics, provenance, and particle-related pollution of an intense dustfall event that occurred in Beijing on 16–17 April 2006. Satellite images reveal that the aeolian dust originated in northeastern Alxa League of Inner Mongolia and passed southeastward across northern Ningxia, middle Inner Mongolia, northern Shaanxi, Shanxi, and Hebei provinces. The dust then moved out of continental China in the vicinity of Beijing and Tianjin. The floating dust led to severe air pollution in Huhhot, Datong, and Beijing. We measured dustfall by collecting dust samples, investigated particle morphology, and calculated the mass medium diameter (MMD) of the dustfall using a scanning electron microscope (SEM). Major elements and mineral content of the dust particles were determined by electron probe and powder X-ray diffractometer, respectively. The relative abundance of dustfall during this event was 12.5–15.0 g m^?2, making up about 10% of the total annual dustfall in Beijing. Dustfall amounted to 205 thousand tons in Beijing, the largest amount observed in recent years. The dust particles were mostly angular, subangular and subrounded in morphology, and the MMD was nearly 12 μm. Particles <10 μm accounted for 54.7% by number, but fine sand particles (larger than 50 μm) made up 53.7% by volume. Particles with diameters larger than 20 μm made up of the predominant volume of the samples (90.35%). Hence, this dustfall event was characterized by a high content of fine sand and coarse silt particles. The principal elements in the dust particles were C, O, Si, Al, Fe, and Ca, whereas the major minerals were quartz, Na-feldspar, calcite, and clay minerals.     

Importance of wet precipitation as a removal and transport process for atmospheric water soluble carbonyls

Carbonyl compounds exist in the atmosphere as either gases or aerosols. Some of them are water soluble and known as oxidation products of biogenic and/or anthropogenic hydrocarbons. Five carbonyl compounds, glyoxal (GO), 4-oxopentanal (4-OPA), glycolaldehyde (GA), hydroxyacetone (HA) and methylglyoxal (MG) have been identified in a temporal series of 12 rain samples. The concentrations of the compounds in the samples were high at the beginning of the rain event and decreased with time to relatively low and fairly constant levels, indicating that the compounds were washed out from the atmosphere at the start of the rain event. Possibly, these compounds also existed in the cloud condensation nuclei (CCN). Wet deposition rates of the carbonyl compounds were calculated for nine samples collected during a 20 h period. The deposition rates ranged from 0 (4-OPA) to 1.2×10⁻¹ mg C m⁻² h⁻¹ (MG) with the average of 2.9×10⁻² mg C m⁻² h⁻¹. Production rates of isoprene oxidation products (GA, HA and MG) in the area surrounding the sampling site were estimated with a chemical box model. The deposition rates exceeded the production rates in most samples. This indicates that the rainfall causes a large net flux of the water soluble compounds from the atmosphere to the ground. Insoluble carbonyl compounds such as n-nonanal and n-decanal were expected to be present in the atmosphere, but were not detected in the rain during the sampling period, suggesting that an aerosol containing these insoluble compounds does not effectively act as a CCN.     

PM2.5 particles and size-segregated ionic species measured during fall season in three urban sites in Korea

Twelve hours integrated fine particles (PM_2.5) and 24-h average size-segregated particles were collected to investigate the chemical characteristics and to determine the size distribution of ionic species during October–December 1999 in three cities of different urban scale; Chongju, Kwangju, and Seoul, Korea. Concentrations of 5-min PM_2.5 black carbon (BC) and hourly criteria air pollutants (PM₁₀, CO, NO_x, SO₂, and O₃) were also measured using the Aethalometer and ambient air monitoring system, respectively.Highest PM_2.5 mass concentrations at Chongju, Kwangju, and Seoul sites were 63.0, 77.9, and 143.7 μg m⁻³, respectively. For the time period when highest PM_2.5 mass occurred, BC level out of PM_2.5 chemical species was highest at both Chongju and Kwangju, and highest NO₃⁻ (23.6 μg m⁻³) followed by BC (23.1 μg m⁻³) were observed at Seoul site, indicating that highest PM_2.5 pollution is closely associated with the traffic emissions. Strong relationships of Fe with BC and Zn at both Kwangju and Seoul sites support that the Fe and Zn measured there are originated partly from same source as BC, i.e. diesel traffics. However, it is suggested that the Fe measured at Chongju is most likely derived from dispersion of soil dust.The size distributions of SO₄²⁻, NO₃⁻, and NH₄⁺ ionic species indicated similar unimodal distributions at all sampling sites. However, different unimodal patterns in the accumulation mode size range with a peak in the smaller size (0.28–0.53 μm, condensation mode) in both Kwangju and Seoul, and in the relatively larger size (0.53–1.0 μm, droplet mode) in Chongju, were found. The potassium ion under the study sites dominates in the fine mode, and its size distribution showed unimodal character with a maximum in the size range 0.56–1.0 μm.     

Spatial and chemical patterns of PM10 in road dust deposited in urban environment

Recent research interest has been focused on road dust resuspension as one of the major sources of atmospheric particulate matter in an urban environment. Given the dearth of studies on the variability of the PM₁₀ fraction of road deposited sediments, our understanding of the main factors controlling this pollutant is incomplete. In the present study a new sampling methodology was devised and applied to collect PM₁₀ deposited mass from 1 m² of road pavement. PM₁₀ road dust fraction was sampled directly from active traffic lanes at 23 sampling sites during a campaign in Barcelona (Spain) in June 2007. The aim of the study was to gain more insight into the variability of mass and chemistry of road dust in different urban environments, such as the city centre, ring roads, and locations nearby demolition/construction sites. The city centre showed values of PM₁₀ road dust within a range of 3–23 mg m^?2, whereas levels reached 24–80 mg m^?2 in locations affected by transport of uncovered heavy trucks. The largest dust loads were measured in the proximity of demolition/construction sites and the harbor entry with values up to 328 mg m^?2.The city centre road dust profiles (%) were enriched in OC, EC, Fe, S, Cu, Zn, Mn, Cr, Sb, Sn, Mo, Zr, Hf, Ge, Ba, Pb, Bi, SO₄^2?, NO₃^?, Cl^? and NH₄⁺, but several crustal components such as Ca, Ti, Na, and Mg were also considerably concentrated. Locations affected by construction and demolition activities had high levels of crustal components such as Ca, Li, Sc, Sr, Rb and also As whereas ring roads, characterized by a higher load of uncovered heavy trucks showed an intermediate composition.Levels of PM₁₀ components per area were also evaluated to quantify the resuspendable amount of each element from 1 m². In the inner city environment mean values of 1363 μg Ca m^?2, 816 μg OC m^?2, 239 μg EC m^?2, 13 μg Cu m^?2, 12 μg Zn m^?2, 1.9 μg Sb m^?2 and 2.0 μg Pb m^?2, in PM₁₀ in all cases, were registered.Moreover the deposited PM load at demolition/construction sites acts as a reservoir or trap for traffic-related particles, which gives rise to large amounts of hazardous pollutants, available for resuspension.     

Estimation of wind blown dust emissions in Europe and its vicinity

The assessment of the wind blown dust emission for Europe and selected regions of North Africa and Southwest Asia was carried out using a mesoscale model. The mesoscale model was parameterized based on the current literature review. The model provides data on PM₁₀ emission from several dust reservoirs (anthropogenic, agriculture, semi- and natural) with spatial resolution of 10 × 10 km and temporal resolution of 1 h. The spatial variability of PM₁₀ emission depends on soil texture, land cover/land use as well as meteorological conditions. Lands covered with water or permanently wet were excluded from the model. The land covered with vegetation is treated as dust reservoir whose dust emission capacity depends on the type of vegetation and cover. The dust reservoirs are divided into reservoirs with stable and unstable surface. The changes of emission in time depend on meteorological parameters.The wind blown dust emission should be treated as a non-continuous spatio-temporal process. The emissions are estimated with high uncertainty. The estimated PM₁₀ yearly total load emitted by wind from the European territory is highly differentiated in space and time and is equal to 0.74 Tg. The total load of PM₁₀ emitted by wind from North African and Southwest Asian land surface located in the vicinity of European boundaries is assessed as nearly 50% (0.43 Tg) of the total load estimated for the whole Europe.The average yearly PM₁₀ emission factor for Europe was estimated at 0.139 Mg km^?2.The PM₁₀ emission from agricultural areas is estimated at 52% of the total wind blown emission from the domain of the European Union project “Improving and applying methods for the calculation of natural and biogenic emissions and assessment of impacts to the air quality” - NatAir.PM₁₀ emission factor for natural areas of Europe is estimated at 0.021 Mg km^?2. Appropriate factors for agricultural areas and anthropogenic areas are 0.157 Mg km^?2 and 0.118 Mg km^?2, respectively. The latter two factors are probably underestimated due to omitting in the model of other dust emission mechanisms than aeolian erosion.     

An analysis of seasonal surface dust aerosol concentrations in the western US (2001–2004): Observations and model predictions

Long-term surface observations indicate that soil dust represents over 30% of the annual fine (particle diameter less than 2.5 μm) particulate mass in many areas of the western US; in spring and summer, it represents an even larger fraction. There are numerous dust-producing playas in the western US, but surface dust aerosol concentrations in this region are also influenced by dust of Asian origin. This study examines the seasonality of surface soil dust concentrations at 15 western US sites using observations from the Interagency Monitoring of PROtected Visual Environments (IMPROVE) network from 2001 to 2004. Average soil concentrations in particulate matter less than 10 μm in diameter (PM₁₀) were lowest in winter and peaked during the summer months at these sites; however, episodic higher-concentration events (>10 μg m⁻³) occurred in the spring, the time of maximum Asian dust transport to the western US. Simulated surface dust concentrations from the Navy Aerosol Analysis and Prediction System (NAAPS) suggested that long-range transport from Asia dominates surface dust concentrations in the western US in the spring, and that, although some long-range transport does occur throughout the year (1–2 μg m⁻³), locally generated dust plays a larger role in the region in summer and fall. However, NAAPS simulated some anomalously high concentrations (>50 μg m⁻³) of local dust in the fall and winter months over portions of the western US. Differences between modeled and observed dust concentrations were attributed to overestimation of total observed soil dust concentrations by the assumptions used to convert IMPROVE measurements into PM₁₀ soil concentrations, lack of inhibition of model dust production in snow-covered regions, and lack of seasonal agricultural sources in the model.     

Seasonal characteristics of water-soluble organic carbon in atmospheric particles in the inland Kanto plain,Japan

An investigation of water-soluble organic carbon (WSOC) in atmospheric particles was conducted as an index of the formation of secondary organic aerosol (SOA) from April 2005 to March 2006 at Maebashi and Akagi located in the inland Kanto plain in Japan. Fine (<2.1 μm) and coarse (2.1–11 μm) particles were collected by using an Andersen low-volume air sampler, and WSOC, organic carbon (OC), elemental carbon (EC), and ionic components were measured. The mean mass concentrations of the fine particles were 22.2 and 10.5 μg m^?3 at Maebashi and Akagi, respectively. The WSOC in fine particles accounted for a large proportion (83%) of total WSOC. The concentration of fine WSOC ranged from 1.2 to 3.5 μg-C m^?3 at Maebashi, rising from summer to fall. At Akagi, it rose from spring to summer, associated with the southerly wind from urban areas. The WSOC/OC ratio increased in summer at both sites, but the ratio at Akagi was higher, which we attributed to differences in primary emissions and secondary formation between the sites. The fine WSOC concentration was significantly positively correlated with concentrations of SO₄^2?, EC, and K⁺, and we inferred that WSOC was produced by photochemical reaction and caused by the combustion of both fuel and biomass. We estimated that SOA accounted for 11–30% of the fine particle mass concentration in this study, suggesting that SOA is a significant year-round component in fine particles.     

Physical characterization of aerosol particles during the Chinese New Year’s firework events

Measurements for particles 10 nm to 10 μm were taken using a Wide-range Particle Spectrometer during the Chinese New Year (CNY) celebrations in 2009 in Shanghai, China. These celebrations provided an opportunity to study the number concentration and size distribution of particles in an especial atmospheric pollution situation due to firework displays. The firework activities had a clear contribution to the number concentration of small accumulation mode particles (100–500 nm) and PM₁ mass concentration, with a maximum total number concentration of 3.8 × 10⁴ cm^?3. A clear shift of particles from nucleation and Aitken mode to small accumulation mode was observed at the peak of the CNY firework event, which can be explained by reduced atmospheric lifetimes of smaller particles via the concept of the coagulation sink. High particle density (2.7 g cm^?3) was identified as being particularly characteristic of the firework aerosols. Recalculated fine particles PM₁ exhibited on average above 150 μg m^?3 for more than 12 hours, which was a health risk to susceptible individuals. Integral physical parameters of firework aerosols were calculated for understanding their physical properties and further model simulation.     

Temporal and spatial variation of sulfur-gas-transfer between coastal marine sediments and the atmosphere

The spatial and temporal variability of sulfur gas fluxes (H₂S, COS, CH₃SH, DMS, and CS₂) at the sediment–air interface were studied in the intertidal Wadden Sea area of Sylt-Rømø (Germany/Denmark) during eight measuring campaigns between June 1991 and September 1994. Measurements were performed mainly at four sites in a sheltered intertidal bay of approximately 6 km² (Königshafen) and discontinuously in a wider range of the 400 km² Sylt-Rømø tidal flat area. In situ fluxes of the S-gases were determined by a dynamic chamber technique focusing on dry sediment periods. Additional experiments were conducted in order to determine changes in S-gas concentrations in the sediment between the surface and 70 cm depth.In most cases H₂S was the dominant S-gas emitted from the sediment to the atmosphere, contributing up to 70% of the total S-emission at this interface. Mean H₂S emission rates ranged between 0.07 and 9.95 μg S m^-2 h^-1. Both emission rates and relative contribution of H₂S were lowest from fine sand and highest from muddy sites. Diurnal variation of H₂S emission was evident in summer and fall with up to 10-fold higher rates during night than during the day. Distinct seasonal variation of H₂S-transfer between the sediment and the atmosphere was observed with higher emission rates in the summer than in spring or fall. The emission of H₂S to the atmosphere was smaller by a factor of 1600–26 000 than the H₂S produced from sulfate reduction. Apparently, the efficiency by which H₂S produced in the sediment is retained and reoxidized by biogeochemical sediment processes is extremely high. Carbonyl sulfide (COS) was emitted with relatively constant rates in space and time with mean flux rates ranging between 0.24 and 2.0 μg S m^-2 h^-1. Carbon disulfide emission rates were comparable to those of COS and varied between 0.3 and 2.23 μg S m^-2 h^-1. DMS played a minor role in the S-gas transfer from uncovered sediment areas contributing between 3.1 and 23% to total S-emission from the sediment to the atmosphere.     

Effect of biomass burning and regional background aerosols on CCN activity derived from airborne in-situ measurements

Airborne in-situ measurements were analyzed to investigate the effects of biomass burning and regional background aerosols on cloud condensation nuclei (CCN) activity in the Pacific Dust Experiment (PACDEX) during April and May 2007. Airmass trajectories with both horizontal and vertical motions were provided to identify the aerosol sources. In the biomass burning cases, the elevated aerosol layers were clearly observed at dry conditions because of the convection of airmass in the source region. The relative aging of aerosols was supported by the ratios of BC to particles with size ranging from 0.1 to 1.0 μm (N_0.1–1.0) and BC to carbon monoxide. Compared to aerosols in the precedent plume of biomass burning, aged particles in the latter plume were more activated to CCN at 0.4% (CCN_0.4%) than 0.1% supersaturation (CCN_0.1%) due to aerosols chemical modification during the aging process. On the other hand, significant difference of CCN_0.4% and CCN_0.1% at regional background aerosols over the Pacific Ocean was due to the activated particles below 1 μm in diameter. Although higher concentrations of aged particles were observed over the eastern Pacific Ocean, activated aerosols to cloud droplet was comparatively similar in the western Pacific Ocean because of the similar concentrations of N_0.1–1.0 in both cases.     

Water-soluble organic nitrogen (WSON) in size-segregated atmospheric particles over the Eastern Mediterranean

Atmospheric water-soluble organic nitrogen (WSON) was determined on size-segregated aerosol particles collected during a two years period (2005–2006) in a remote marine location in the Eastern Mediterranean (Finokalia, Crete island). Average concentration of WSON was 5.5 ± 3.9 nmol m^?3 and 11.6 ± 14.0 nmol m^?3 for coarse (PM_1.3-10) and fine (PM_1.3) mode respectively, corresponding to 13% of Total Dissolved Nitrogen (TDN) in both modes. Air masses origin and correlation with tracers of natural and anthropogenic sources indicate that combustion process (biomass burning and fossil fuel) and African dust play an important role in regulating levels of WSON in both coarse and fine aerosol fractions. Chemical speciation of organic nitrogen pool was attempted by analyzing 47 fine aerosol samples (PM₁) for 17 free amino acids (N-FAA), dimethylamine (DMA) and trimethylamine (TMA). The average concentration of N-FAA was 0.5 ± 0.5 nmol m^?3, while the average concentration of DMA was 0.2 ± 0.8 nmol m^?3, TMA was below detection limit. The percentage contribution of N-FAA and DMA to WSON was 2.1 ± 2.3% and 0.9 ± 3.4%, respectively.     

Quantification of Saharan dust contribution to PM10 concentrations over Italy during 2003–2005

Italy is frequently affected by Saharan dust intrusions, which result in high PM₁₀ concentrations in the atmosphere and can cause the exceedances of the PM₁₀ daily limits (50 μg m^?3) set by the European Union (EU/2008/50). The estimate of African dust contribution to PM₁₀ concentrations is therefore a key issue in air quality assessment and policy formulation. This study presents a first identification of Saharan dust outbreaks as well as an estimate of the African dust contribution to PM₁₀ concentrations during the period 2003–2005 over Italy. The identification of dust events has been carried out by looking at different sources of information such as monitoring network observations, satellite images, ground measurements of aerosol optical properties, dust model simulations and air mass backward trajectory analysis. The contribution of Saharan dust to PM₁₀ monthly concentrations has been estimated at seven Italian locations. The results are both spatially (with station) and temporally (with month and year) variable, as a consequence of the variability of the meteorological conditions. However, excluding the contribution of severe dust events (21st February 2004, 25th–28th September 2003, 23rd–27th March 2005), the monthly contribution of dust varies approximately between 1 μg m^?3 and 10 μg m^?3 throughout year 2005 and between 1 μg m^?3 and 8 μg m^?3 throughout year 2003. In 2004 the dust concentration is lower than 2003 and 2005 (<5 μg m^?3 at all sites). The reduction in the number of daily exceedances of the limit value (50 μg m^?3) after subtraction of the dust contribution is also calculated at each station: it varies with station between 20% and 50% in 2005 and between 5% and 25% in 2003 and 2004.     

Contribution of carbonaceous material to cloud condensation nuclei concentrations in European background (Mt. Sonnblick) and urban (Vienna) aerosols

During four intensive measurement campaigns (two on Mt. Sonnblick, European background aerosol, and two in Vienna, urban aerosol), cloud condensation nuclei (CCN) were measured at supersaturations of 0.5%. Impactor measurements of the mass size distribution in the size range 0.1–10 μm were performed and later analyzed for Cl^-, NO^-₃, SO^2-₄, Na⁺, NH⁺₄, K⁺, Ca²⁺ and Mg²⁺ by ion chromatography, for total carbon (TC) using a combustion method, and for black carbon (BC) by an optical method (integrating sphere). Organic carbon (OC) was defined as the difference between TC (minus carbonate carbon) and BC. At all sites, the mass fraction of BC in the submicron aerosol was comparable (4–5%). CCN concentrations on Mt. Sonnblick were found to be 10–30% of those measured in Vienna, although high Mt. Sonnblick concentrations were comparable to low Vienna concentrations (around 800 cm^-3). The contribution of organic material was estimated from the mass concentrations of the chemical species sampled on the impactor stage with the lowest cut point (0.1–0.215 μm aerodynamic equivalent diameter). On Mt. Sonnblick, TC material contributed 11% to the total mass in fall 1995, and 67% in summer 1996, while the OC fraction was 6 and 61%. The combined electrolytes and mineral material contributed 18 and 16% in fall and summer. During the Vienna spring campaign, the contributions of OC and electrolytes to the total mass concentration in this size range were 48 and 36%, respectively.     

SPM and fungal spores in the ambient air of west Korea during the Asian dust (Yellow sand) period

The relationship between suspended particulate matter (SPM) and fungal spore was investigated in Seosan, a rural county along the west coast of Korea, in the spring of 2000. SPM concentrations in the air were 199.8 μg m⁻³ in the first Asian dust period (23–24 March), 249.4 μg m⁻³ in the second Asian dust period (7–9 April) and 98.9 μg m⁻³ in the non-Asian dust period (12–16 May), respectively. The majority of the total SPM were composed of coarse particles sized about 5 μm during the two Asian dust periods. Four molds genera grown from airborne fungal spores were identified in colonies grown from SPM samples taken during the Asian dust periods. All the genera found, Fusarium, Aspergillus, Penicillium and Basipetospora, are hyphomycetes in the division Deuteromycota. Morphologically, more diversified mycelia of hyphomycetes were grown on the sample captured from 1.1 to 2.1 μm sized SPM than on the other sized samples gathered in the dust periods. On the other hand, no mold was observed on the sample of 1.1–2.1 μm sized SPM in the non-Asian dust period. From these results, it seems evident that several sorts of fine sized fungal spores were suspended in the atmospheric environment of this study area during Asian dust periods.     

Nitrous oxide emissions from mineral and organic soils of a Norway spruce stand in South–West Germany

Due to the high temporal and spatial variability of N₂O fluxes, estimates of N₂O emission from temperate forest ecosystems are still highly uncertain, particularly at larger scales. Although highest N₂O emissions with up to 7.0 kg N ha⁻¹ yr⁻¹ were mainly reported for soils affected by stagnant water, most of the reported gas flux measurements were performed at forest sites with well-aerated soils yielding mostly to low mean annual emission rates less than 1.0 kg N ha⁻¹ yr⁻¹. This study compares N₂O fluxes from upland (Cambisols) and temporally water-logged (Gleysols, Histosols) soils of the Central Black Forest (South-West Germany) over a period of 2 yr. Mean annual N₂O fluxes from investigated soils ranged between 0.2 and 3.9 kg N ha⁻¹ yr⁻¹. The fluxes showed a large variability between the different soil types. Emissions could be clearly ranked in the following order: Cambisols (0.26–0.75 kg N ha⁻¹ yr⁻¹)<Gleysols (1.37–2.68 kg N ha⁻¹ yr⁻¹)<Histosol (3.66–3.95 kg N ha⁻¹ yr⁻¹). Although the Cambisols cover two-thirds of the investigated area, only about half of the overall N₂O is emitted from this soil type. Therefore, regional or national N₂O fluxes from temperate forest soils are underestimated if soils characterised by intermediate aeration conditions are disregarded.