On-road emission characteristics of heavy-duty diesel vehicles in Shanghai

On-road vehicle tests of nine heavy-duty diesel trucks were conducted using SEMTECH-D, an emissions measuring instrument provided by Sensors, Inc. The total length of roads for the tests was 186 km. Data were obtained for 37,255 effective driving cycles, including 17,216 on arterial roads, 15,444 on residential roads, and 4595 on highways. The impacts of speed and acceleration on fuel consumption and emissions were analyzed. Results show that trucks spend an average of 16.5% of the time in idling mode, 25.5% in acceleration mode, 27.9% in deceleration mode, and only 30.0% at cruise speed. The average emission factors of CO, total hydrocarbons (THC), and NO_x for the selected vehicles are (4.96±2.90), (1.88±1.03) and (6.54±1.90) g km⁻¹, respectively. The vehicle emission rates vary significantly with factors like speed and acceleration. The test results reflect the actual traffic situation and the current emission status of diesel trucks in Shanghai. The measurements show that low-speed conditions with frequent acceleration and deceleration, particularly in congestion conditions, are the main factors that aggravate vehicle emissions and cause high emissions of CO and THC. Alleviating congestion would significantly improve vehicle fuel economy and reduce CO and THC emissions.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Mercury emissions from automobiles using gasoline,diesel, and LPG

Mercury (Hg) emissions from gasoline, diesel, and liquefied petroleum gas (LPG) vehicles were measured and speciated (particulate, oxidized, and elemental mercury). First, three different fuel types were analyzed for their original Hg contents; 571.1±4.5 ng L⁻¹ for gasoline, 185.7±2.6 ng L⁻¹ for diesel, and 1230.3±23.5 ng L⁻¹ for LPG. All three vehicles were then tested at idling and driving modes. Hg in the exhaust gas was mostly in elemental form (Hg⁰), and no detectable levels of particulate (Hg^p) or oxidized (Hg²⁺) mercury were measured. At idling modes, Hg concentrations in the exhaust gas of gasoline, diesel, and LPG vehicles were 1.5–9.1, 1.6–3.5, and 10.2–18.6 ng m⁻³, respectively. At driving modes, Hg concentrations were 3.8–16.8 ng m⁻³ (gasoline), 2.8–8.5 ng m⁻³ (diesel), and 20.0–26.9 ng m⁻³ (LPG). For all three vehicles, Hg concentrations at driving modes were higher than at idling modes. Furthermore, Hg emissions from LPG vehicle was highest of all three vehicle types tested, both at idling and driving modes, as expected from the fact that it had the highest original fuel Hg content.     

Influence of fuel composition on polycyclic aromatic hydrocarbon emissions from a fleet of in-service passenger cars

The composition of exhaust emissions from eight in-service passenger cars powered by liquefied petroleum gas (LPG) and unleaded petrol (ULP) were measured on a chassis dynamometer at two driving speeds (60 and 80 km h⁻¹) with the aims of evaluating their polycyclic aromatic hydrocarbon (PAH) contents and investigating the effects of the type of fuel on vehicle performance, ambient air quality and associated health risks. Naphthalene, fluorene, phenanthrene, anthracene, pyrene, chrysene, benzo(a)anthracene and benzo(b)fluoranthene were the most prominent PAHs emitted by both ULP and LPG powered cars. The total emission factors of PAHs from LPG cars were generally lower than (but statistically comparable with) those of ULP cars. Similarly, the total BAP_eq of the PAHs emitted by LPG cars were lower than those from ULP cars. Multi-criteria decision making (MCDM) methods showed that cars powered by LPG fuel performed better than those powered by ULP fuel in term of PAH levels. The implications of these observations on the advantages and disadvantages of using ULP and LPG fuels are discussed.     

Characterization of on-road vehicle emission factors and microenvironmental air quality in Beijing,China

In this paper, we report the results and analysis of a recent field campaign in August 2007 investigating the impacts of emissions from transportation on air quality and community concentrations in Beijing, China. We conducted measurements in three different environments, on-road, roadside and ambient. The carbon monoxide, black carbon and ultrafine particle number emission factors for on-road light-duty vehicles are derived to be 95 g kg^?1-fuel, 0.3 g kg^?1-fuel and 1.8 × 10¹⁵ particles kg^?1-fuel, respectively. The emission factors for on-road heavy-duty vehicles are 50 g kg^?1-fuel, 1.3 g kg^?1-fuel and 1.1 × 10¹⁶ particles kg^?1-fuel, respectively. The carbon monoxide emission factors from this study agree with those derived from remote sensing and on-board vehicle emission testing systems in China. The on-road black carbon and particle number emission factors for Chinese vehicles are reported for the first time in the literature. Strong traffic impacts can be observed from the concentrations measured in these different environments. Most clear is a reflection of diesel truck traffic activity in black carbon concentrations. The comparison of the particle size distributions measured at the three environments suggests that the traffic is a major source of ultrafine particles. A four-day traffic control experiment conducted by the Beijing Government as a pilot to test the effectiveness of proposed controls was found to be effective in reducing extreme concentrations that occurred at both on-road and ambient environments.     

Trends in on-road vehicle emissions of ammonia

Motor vehicle emissions of ammonia have been measured at a California highway tunnel in the San Francisco Bay area. Between 1999 and 2006, light-duty vehicle ammonia emissions decreased by 38 ± 6%, from 640 ± 40 to 400 ± 20 mg kg^?1. High time resolution measurements of ammonia made in summer 2001 at the same location indicate a minimum in ammonia emissions correlated with slower-speed driving conditions. Variations in ammonia emission rates track changes in carbon monoxide more closely than changes in nitrogen oxides, especially during later evening hours when traffic speeds are highest. Analysis of remote sensing data of Burgard et al. (Environmental Science Technology 2006, 40, 7018–22) indicates relationships between ammonia and vehicle model year, nitrogen oxides, and carbon monoxide. Ammonia emission rates from diesel trucks were difficult to measure in the tunnel setting due to the large contribution to ammonia concentrations in a mixed-traffic bore that were assigned to light-duty vehicle emissions. Nevertheless, it is clear that heavy-duty diesel trucks are a minor source of ammonia emissions compared to light-duty gasoline vehicles.     

A new approach to in-situ determination of roadside particle emission factors of individual vehicles under conventional driving conditions

A method for continuous on-road measurements of particle number emissions for both diesel- and petrol-fuelled vehicles is presented. The setup allows the determination of particle number emission factors on an individual vehicle basis by the simultaneous measurement of CO₂ and particle concentrations. As an alternative to previous measurements on the kerbside, the sample is taken directly in the street, with the advantage of sampling in-situ within the exhaust plumes of passing vehicles, allowing the separation of the individual high-concentration plumes. The method was tested in two experiments that were conducted in the Gothenburg area. In the first study, which was performed at an urban roadside, we were able to determine particle emission factors from individual vehicles in a common car fleet passing the measurement site. The obtained emission factors were of the same order of magnitude (between 1.4 × 10¹² and 1.8 × 10¹⁴ particles km^?1) as values published in the recent literature for light duty vehicles. An additional on-road experiment was conducted at a rural road with four light duty reference vehicles (three of them petrol-powered and one diesel-powered) at driving speeds of 50 and 70 km h^?1, realised with different engine speeds. The results of the traffic emission studies show that the method is applicable provided that instruments with an adequate dynamic range are used and that the traffic is not too dense. In addition, the variability in particle emissions for a specified driving condition was estimated.     

Nanoparticle emissions on Minnesota highways

The objective of this project was to characterize on-road aerosol on highways surrounding the Minneapolis area. Data were collected under varying on-road traffic conditions and in residential areas to determine the impact of highway traffic on air quality. The study was focused on determining on-road nanoparticle concentrations, and estimating fuel-specific and particle emissions km⁻¹.On-road aerosol number concentrations ranged from 10⁴ to 10⁶ particles cm⁻³. The highest nanoparticle concentrations were associated with high-speed traffic. At high vehicular speeds engine load, exhaust temperature, and exhaust flow all increase resulting in higher emissions. Less variation was observed in particle volume, a surrogate measure of particle mass. Most of the particles added by the on-road fleet were below 50 nm in diameter. Particles in this size range may dominate particle number, but contribute little to particle volume or mass. Furthermore, particle number is strongly influenced by nucleation and coagulation, which have little or no effect on particle volume. Measurements made in heavy traffic, speeds<32 km h⁻¹, produced lower number concentrations and larger particles.Number concentrations measured in residential areas, 10–20 m from the highway, were considerably lower than on-road concentrations, but the size distributions were similar to on-road aerosol with high concentrations of very small (<20 nm) particles. Much lower number concentrations and larger particles were observed in residential areas located 500–700 m from the highway.Estimated emissions of total particle number larger than 3 nm ranged from 1.9 to 9.9×10¹⁴ particles km⁻¹ and 2.2–11×10¹⁵ particles (kg fuel)⁻¹ for a gasoline-dominated vehicle fleet.     

Emissions of PCDD/Fs,PCBs, and PAHs from legacy on-road heavy-duty diesel engines

Exhaust emissions of seventeen 2,3,7,8-substituted polychlorinated dibenzo-p-dioxin/furan (PCDD/F) congeners, tetra–octa PCDD/F homologues, 12 WHO 2005 polychlorinated biphenyl (PCB) congeners, mono–nona chlorinated biphenyl homologues, and 19 polycyclic aromatic hydrocarbons (PAHs) from three legacy diesel engines were investigated. The three engines tested were a 1985 model year GM 6.2 J-series engine, a 1987 model year Detroit Diesel Corporation 6V92 engine, and a 1993 model year Cummins L10 engine. Results were compared to United States’ mobile source inventory for on-road diesel engines, as well as historic and modern diesel engine emission values. The test fuel contained chlorine at 9.8 ppm which is 1.5 orders of magnitude above what is found in current diesel fuel and 3900 ppm sulfur to simulate fuels that would have been available when these engines were produced. Results indicate PCDD/F emissions of 13.1, 7.1, and 13.6 pg International Toxic Equivalency (I-TEQ) L⁻¹ fuel consumed for the three engines respectively, where non-detects are equal to zero. This compares with a United States’ mobile source on-road diesel engine inventory value of 946 pg I-TEQ L⁻¹ fuel consumed and 1.28 pg I-TEQ L⁻¹ fuel consumed for modern engines equipped with a catalyzed diesel particle filter and urea selective catalytic reduction. PCB emissions are 2 orders of magnitude greater than modern diesel engines. PAH results are representative of engines from this era based on historical values and are 3–4 orders of magnitude greater than modern diesel engines.     

Effects of biodiesel on emissions of regulated air pollutants and polycyclic aromatic hydrocarbons under engine durability testing

An 80,000-km durability test was performed on two engines using diesel and biodiesel (methyl ester of waste cooking oil) as fuel in order to examine emissions resulting from the use of biodiesel. The test biodiesel (B20) was blended with 80% diesel and 20% methyl ester derived from waste cooking oil. Emissions of regulated air pollutants, including CO, HC, NO_x, particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) were measured at 20,000-km intervals. The identical-model engines were installed on a standard dynamometer equipped with a dilution tunnel used to measure the pollutants. To simulate real-world driving conditions, emission measurements were made in accordance with the United States Environmental Protection Agency (USEPA) FTP transient cycle guidelines. At 0 km of the durability test, HC, CO and PM emission levels were lower for the B20 engine than those for diesel. After running for 20,000 km and longer, they were higher. However, the deterioration coefficients for these regulated air pollutants were not statistically higher than 1.0, implying that the emission factors do not increase significantly after 80,000 km of driving. Total (gaseous+particulate phase) PAH emission levels for both B20 and diesel decreased as the driving mileage accumulated. However, for the engine using B20 fuel, particulate PAH emissions increased as engine mileage increased. The average total PAH emission factors were 1097 and 1437 μg bhp h⁻¹ for B20 and diesel, respectively. For B20, the benzo[a]pyrene equivalence emission factors were 0.77, 0.24, 0.20, 7.48, 5.43 and 14.1 μg bhp h⁻¹ for 2-, 3-, 4-, 5-, 6-ringed and total PAHs. Results show that B20 use can reduce both PAH emission and its corresponding carcinogenic potency.     

Hydrocarbon emission fingerprints from contemporary vehicle/engine technologies with conventional and new fuels

The present paper presents results from the analysis of 29 individual C₂–C₉ hydrocarbons (HCs) specified in the European Commission Ozone Directive. The 29 HCs are measured in exhaust from common, contemporary vehicle/engine/fuel technologies for which very little or no data is available in the literature. The obtained HC emission fingerprints are compared with fingerprints deriving from technologies that are being phased out in Europe. Based on the total of 138 emission tests, thirteen type-specific fingerprints are extracted (Mean ± SD percentage contributions from individual HCs to the total mass of the 29 HCs), essential for receptor modelling source apportionment. The different types represent exhaust from Euro3 and Euro4 light-duty (LD) diesel and petrol-vehicles, Euro3 heavy-duty (HD) diesel exhaust, and exhaust from 2-stroke preEuro, Euro1 and Euro2 mopeds. The fuels comprise liquefied petroleum gas, petrol/ethanol blends (0–85% ethanol), and mineral diesel in various blends (0–100%) with fatty acid methyl esters, rapeseed methyl esters palm oil methyl esters, soybean oil methyl or sunflower oil methyl esters. Type-specific tracer compounds (markers) are identified for the various vehicle/engine/fuel technologies.An important finding is an insignificant effect on the HC fingerprints of varying the test driving cycle, indicating that combining HC fingerprints from different emission studies for receptor modelling purposes would be a robust approach.The obtained results are discussed in the context of atmospheric ozone formation and health implications from emissions (mg km^?1 for LD and mopeds and mg kW h^?1 for HD, all normalised to fuel consumption: mg dm^?3 fuel) of the harmful HCs, benzene and 1,3-butadiene.Another important finding is a strong linear correlation of the regulated “total” hydrocarbon emissions (tot-HC) with the ozone formation potential of the 29 HCs (ΣPO₃ = (1.66 ± 0.04) × tot-RH; r² = 0.93). Tot-HC is routinely monitored in emission control laboratories, whereas C₂–C₉ are not. The revealed strong correlations broadens the usability of data from vehicle emission control laboratories and facilitates the comparison of the ozone formation potential of HCs in exhaust from of old and new vehicle/engine/fuel technologies.     

On-Road Motor Vehicle Emissions and Fuel Consumption in Urban Driving Conditions

ABSTRACT

This paper reports on the analysis of on-road vehicle speed, emission, and fuel consumption data collected by four instrumented vehicles. Time-, distance-, and fuel-based average fuel consumption, as well as CO, HC, NO_x, and soot emission factors, were derived. The influences of instantaneous vehicle speed on emissions and fuel consumption were studied. It was found that the fuel-based emission factors varied much less than the time- and distance-based emission factors as instantaneous speed changed. The trends are similar to the results obtained from laboratory tests. The low driving speed contributed to a significant portion of the total emissions over a trip. Furthermore, the on-road data were analyzed using the modal approach. The four standard driving modes are acceleration, cruising, deceleration, and idling. It was found that the transient driving modes (i.e., acceleration and deceleration) were more polluting than the steady-speed driving modes (i.e., cruising and idling) in terms of g/km and g/ sec. These results indicated that the on-road emission measurement is feasible in deriving vehicle emissions and fuel consumption factors in urban driving conditions.     

On-road motor vehicle emissions and fuel consumption in urban driving conditions

This paper reports on the analysis of on-road vehicle speed, emission, and fuel consumption data collected by four instrumented vehicles. Time-, distance-, and fuel-based average fuel consumption, as well as CO, HC, NOx, and soot emission factors, were derived. The influences of instantaneous vehicle speed on emissions and fuel consumption were studied. It was found that the fuel-based emission factors varied much less than the time- and distance-based emission factors as instantaneous speed changed. The trends are similar to the results obtained from laboratory tests. The low driving speed contributed to a significant portion of the total emissions over a trip. Furthermore, the on-road data were analyzed using the modal approach. The four standard driving modes are acceleration, cruising, deceleration, and idling. It was found that the transient driving modes (i.e., acceleration and deceleration) were more polluting than the steady-speed driving modes (i.e., cruising and idling) in terms of g/km and g/sec. These results indicated that the on-road emission measurement is feasible in deriving vehicle emissions and fuel consumption factors in urban driving conditions.     

Chemical speciation of PM emissions from heavy-duty diesel vehicles equipped with diesel particulate filter (DPF) and selective catalytic reduction (SCR) retrofits

Four heavy-duty diesel vehicles (HDDVs) in six retrofitted configurations (CRT^®, V-SCRT^®, Z-SCRT^®, Horizon, DPX and CCRT^®) and a baseline vehicle operating without after--treatment were tested under cruise (50 mph), transient UDDS and idle driving modes. As a continuation of the work by Biswas et al. [Biswas, S., Hu, S., Verma, V., Herner, J., Robertson, W.J., Ayala, A., Sioutas, C., 2008. Physical properties of particulate matter (PM) from late model heavy-duty diesel vehicles operating with advanced emission control technologies. Atmospheric Environment 42, 5622–5634.] on particle physical parameters, this paper focuses on PM chemical characteristics (Total carbon [TC], Elemental carbon [EC], Organic Carbon [OC], ions and water-soluble organic carbon [WSOC]) for cruise and UDDS cycles only. Size-resolved PM collected by MOUDI–Nano-MOUDI was analyzed for TC, EC and OC and ions (such as sulfate, nitrate, ammonium, potassium, sodium and phosphate), while Teflon coated glass fiber filters from a high volume sampler were extracted to determine WSOC. The introduction of retrofits reduced PM mass emissions over 90% in cruise and 95% in UDDS. Similarly, significant reductions in the emission of major chemical constituents (TC, OC and EC) were achieved. Sulfate dominated PM composition in vehicle configurations (V-SCRT^®-UDDS, Z-SCRT^®-Cruise, CRT^® and DPX) with considerable nucleation mode and TC was predominant for configurations with less (Z-SCRT^®-UDDS) or insignificant (CCRT^®, Horizon) nucleation. The transient operation increases EC emissions, consistent with its higher accumulation PM mode content. In general, solubility of organic carbon is higher (average ～5 times) for retrofitted vehicles than the baseline vehicle. The retrofitted vehicles with catalyzed filters (DPX, CCRT^®) had decreased OC solubility (WSOC/OC: 8–25%) unlike those with uncatalyzed filters (SCRT^®s, Horizon; WSOC/OC ～ 60–100%). Ammonium was present predominantly in the nucleation mode, indicating that ternary nucleation may be the responsible mechanism for formation of these particles.     

Road traffic emission factors for heavy metals

Quantifying the emissions and concentrations of heavy metals in urban air is a prerequisite for assessing their health effects. In this paper a combination of measurements and modelling is used to assess the contribution from road traffic emissions. Concentrations of particulate heavy metals in air were measured simultaneously during 1 year at a densely trafficked street and at an urban background site in Stockholm, Sweden. Annual mean concentrations of cadmium were 50 times lower than the EU directive and for nickel and arsenic concentrations were 10 and six times lower, respectively. More than a factor of two higher concentrations was in general observed at the street in comparison to roof levels indicating the strong influence from local road traffic emissions. The only compound with a significantly decreasing trend in the urban background was Pb with 9.1 ng m^?3 in 1995/96 compared to 3.4 ng m^?3 2003/04. This is likely due to decreased emissions from wear of brake linings and reduced emissions due to oil and coal combustion in central Europe.Total road traffic emission factors for heavy metals were estimated using parallel measurements of NOx concentrations and knowledge of NOx emission factors. In general, the emission factors for the street were higher than reported in road tunnel measurements. This could partly be due to different driving conditions, since especially for metals which are mainly emitted from brake wear, more stop and go driving in the street compared to in road tunnels is likely to increase emissions. Total emissions were compared with exhaust emissions, obtained from the COPERT model and brake wear emissions based on an earlier study in Stockholm. For Cu, Ni and Zn the sum of brake wear and exhaust emissions agreed very well with estimated total emission factors in this study. More than 90% of the road traffic emissions of Cu were due to brake wear. For Ni more than 80% is estimated to be due to exhaust emissions and for Zn around 40% of road traffic emissions are estimated to be due to exhaust emissions. Pb is also mainly due to exhaust emissions (90%); a fuel Pb content of only 0.5 mg L^?1 would give similar emission factor as that based on the concentration increment at the street. This is the first study using simultaneous measurements of heavy metals at street and roof enabling calculations of emission factors using a tracer technique.     

Comparison of on-road emissions for B-0, B-10, and B-20 in transit buses

Biodiesels are often marketed as being cleaner than regular diesel for emissions. Emission test results depend on the biodiesel blend, but laboratory tests suggest that biodiesels decrease particulate matter, carbon monoxide, hydrocarbons, and air toxins when compared to regular diesel. Results for the amount of oxides of nitrogen (NOx) have been less conclusive. Tests have also not evaluated the commonly available ranges of biodiesel blends in the laboratory. Additionally, little information is available from on-road studies, so the effectiveness of using biodiesels to reduce actual emissions is unknown. A more complex relationship exists between engine operation and the rate of emission production than is typically evaluated using engine or chassis dynamometer tests. On-road emissions can vary dramatically because emissions are correlated to engine mode. Additionally, activity such as idling, acceleration, deceleration, and operation against a grade can produce higher emissions than more stable engine operating modes. Because these modes are not well captured in a laboratory environment, understanding on-road relationships is critical in evaluating the emissions reductions that may be possible with biodiesels. More tests and quantifications of the effects of different blends on engine and vehicle performance are required to promote widespread use of biodiesel. The objective of this research was to conduct on-road tests to compare the emission impacts of different blends of biodiesel to regular diesel fuel under different operating conditions. The team conducted on-road tests that utilized a portable emissions monitoring system that was used to instrument transit buses. Regular diesel and different blends of biodiesel were evaluated during on-road engine operation by instrumenting three in-use transit buses, from the CyRide system of Ames, Iowa, along an existing transit route.     

Characterization of gaseous pollutant and particulate matter emission rates from a commercial broiler operation part I: Observed trends in emissions

This paper characterizes the emission rates of size fractionated particulate matter, inorganic aerosols, acid gases, ammonia and methane measured over four flocks at a commercial broiler chicken facility. Mean emission rates of each pollutant, along with sampling notes, were reported in this paper, the first in a series of two. Sampling notes were needed because inherent gaps in data may bias the mean emission rates.The mean emission rates of PM₁₀ and PM_2.5 were 5.0 and 0.78 g day^?1 [Animal Unit, AU]^?1, respectively, while inorganic aerosols mean emission rates ranged from 0.15 to 0.46 g day^?1 AU^?1 depending on the season. The average total acid gas emission rate was 0.43 g day^?1 AU^?1 with the greatest contribution from nitrous and nitric acids and little contribution from sulfuric acid (as SO₂).Ammonia emissions were seasonally dependent, with a mean emission rate of 66.0 g day^?1 AU^?1 in the cooler seasons and 94.5 g day^?1 AU^?1 during the warmer seasons. Methane emissions were relatively consistent with a mean emission rate of 208 g day^?1 AU^?1.The diurnal pattern in each pollutant’s emission rate was relatively consistent after normalizing the hourly emissions according to each daily mean emission rate. Over the duration of a production cycle, all the measured pollutants’ emissions increased proportionally to the total live mass of birds in the house, with the exception of ammonia.Interrelationships between pollutants provide evidence of mutually dependent release mechanisms, which suggests that it may be possible to fill data gaps with minimal data requirements. In the second paper (Roumeliotis, T.S., Dixon, B.J., Van Heyst, B.J. Characterization of gaseous pollutants and particulate matter emission rates from a commercial broiler operation part II: correlated emission rates. Atmospheric Environment, 2010.), regression correlations are developed to estimate daily mean emission rates for data gaps and, using the normalized hourly diurnal patterns from this paper, emission factors were generated for each pollutant.     

Development of a driving cycle for Hong Kong

The paper presents the results of the development of a standard driving cycle in the urban areas of Hong Kong. On-road speed–time data were collected by an instrumented diesel vehicle along two fixed routes located in two urban districts in Hong Kong. The collected data were analyzed and compared with mandatory driving cycles used elsewhere. It was found that none of these mandatory cycles could satisfactorily describe the driving characteristics in Hong Kong. A unique driving cycle was therefore developed for Hong Kong. The cycle was built up by extracting parts of the on-road speed data such that the summary statistics of the sample are close to that derived from the data population of the test runs.     

Pre- and post-catalyst-, fuel-, velocity- and acceleration-dependent benzene emission data of gasoline-driven EURO-2 passenger cars and light duty vehicles

The benzene emission characteristics of six gasoline-driven EURO-2 vehicles, three passenger cars and three light duty vehicles, have been determined by time-resolved chemical ionization mass spectrometry. Aliquots of the exhaust gas were monitored pre- and post-catalyst with two independently operating mass spectrometers. Each vehicle was driven with two different fuels having benzene contents of 1 and 2 vol%. Seven driving cycles—including the European (EDC) and the US (FTP-75) driving cycle—with a total driving time of about 8800 s were studied. Herein, we discuss the average emission characteristics of the entire fleet at transient driving in the velocity range of 0–150 km h⁻¹. The conversion efficiencies of the involved catalytic systems were deduced from the pre- and post-catalyst data. On average, the vehicles showed optimal benzene conversion efficiencies (>95%) in the velocity range of 30–90 km h⁻¹. When driving below 20 or above 100 km h⁻¹ reduced benzene conversion was found (80–82%). No benzene conversion was observed when driving above 130 km h⁻¹. In contrast, the post-catalyst benzene emissions exceeded those of the untreated exhaust gas by 19–49%. Thus on an average, benzene was formed across the catalysts under these conditions. In addition, the influence of the benzene content of the gasoline on the tail-pipe emissions was also studied. The use of the gasoline with 1 vol% benzene instead of 2 vol% induced a 20–30% reduction of the post-catalyst emissions when driving below 50 km h⁻¹. The fuel effect became smaller above 100 km h⁻¹ and was even negative at high engine load (>130 km h⁻¹). Thus under these conditions, when benzene is formed across the catalyst, the amount of the emitted benzene was independent of the benzene level of the fuel.     

Comparison of carbonyl compounds emissions from diesel engine fueled with biodiesel and diesel

The characteristics of carbonyl compounds emissions were investigated on a direct injection, turbocharged diesel engine fueled with pure biodiesel derived from soybean oil. The gas-phase carbonyls were collected by 2,4-dinitrophenylhydrazine (DNPH)-coated silica cartridges from diluted exhaust and analyzed by HPLC with UV detector. A commercial standard mixture including 14 carbonyl compounds was used for quantitative analysis. The experimental results indicate that biodiesel-fueled engine almost has triple carbonyls emissions of diesel-fueled engine. The weighted carbonyls emission of 8-mode test cycle of biodiesel is 90.8 mg (kW h)^?1 and that of diesel is 30.7 mg (kW h)^?1. The formaldehyde is the most abundant compound of carbonyls for both biodiesel and diesel, taking part for 46.2% and 62.7% respectively. The next most significant compounds are acetaldehyde, acrolein and acetone for both fuels. The engine fueled with biodiesel emits a comparatively high content of propionaldehyde and methacrolein. Biodiesel, as an alternative fuel, has lower specific reactivity (SR) caused by carbonyls compared with diesel. When fueled with biodiesel, carbonyl compounds make more contribution to total hydrocarbon emission.