Contribution of harbour activities to levels of particulate matter in a harbour area: Hada Project-Tarragona Spain

The present study seeks to estimate the impact of harbour activities on PM10 levels based on a complete chemical characterisation of 90 PM10 samples periodically collected between September 2004 and September 2005 in the harbour of Tarragona as part of the HADA (LIFE Program EC) project. Interpretation of the time series of major and trace PM10 components allowed us to identify peaks of PM10 components related to the activities in the harbour. A factor analysis of PM10 enabled us to identify the crustal, traffic, secondary and sea spray sources, and one other source related to the re-suspension of materials handled in the harbour. The multi-linear regression analysis demonstrated a high anthropogenic contribution (62%) for PM10 at the harbour, mainly related to traffic (34% of PM10). Comparison with an earlier study, using the same methodology, at an urban background monitoring station in Tarragona, showed a good correlation for the annual average concentrations of most PM10 components at the two stations. At the harbour higher concentrations were obtained for tracers (P and Mn, and V and Ni in a lesser extent) of some mineral bulk cargo materials. Re-suspension of loose materials by means of wind and/or traffic was identified as one of the major contributors to PM10 in the harbour. Abatement strategies designed to reduce levels of PM10 in the harbour and nearby areas are provided.     

Measurement of particulate concentrations produced during bulk material handling at the Tarragona harbor

Bulk material handling can be a significant source of particles in harbor areas. The atmospheric impact of a number of loading/unloading activities of diverse raw materials has been assessed from continuous measurements of ambient particle concentrations recorded close to the emission sources. Two experimental campaigns have been carried out in the Tarragona port to document the impact of specific handling operations and bulk materials. Dusty bulk materials such as silica–manganese powder, tapioca, coal, clinker and lucerne were dealt with during the experiments. The highest impacts on ambient particle concentrations were recorded during handling of clinker. For this material and silica–manganese powder, high concentrations were recorded in the fine grain size (<2.5 μm). The lowest impacts on particulate matter concentrations were recorded during handling of tapioca and lucerne, mainly in the coarse grain size (2–5–10 μm). The effectiveness of several emission abatement measures, such as ground watering to diminish coal particle resuspension, was demonstrated to reduce ambient concentrations by up to two orders of magnitude. The importance of other good practices in specific handling operations, such as controlling the height of the shovel discharge, was also evidenced by these experiments. The results obtained can be further utilized as a useful experimental database for emission factor estimations.     

Standardized emissions inventory methodology for open-pit mining areas

INTRODUCTION: There is still interest in a unified methodology to quantify the mass of particulate material emitted into the atmosphere by activities inherent to open-pit mining. For the case of total suspended particles (TSP), the current practice is to estimate such emissions by developing inventories based on the emission factors recommended by the USEPA for this purpose. However, there are disputes over the specific emission factors that must be used for each activity and the applicability of such factors to cases quite different to the ones under which they were obtained. There is also a need for particulate matter with an aerodynamic diameter less than 10?μm (PM(10)) emission inventories and for metrics to evaluate the emission control programs implemented by open-pit mines. STANDARDIZED EMISSION INVENTORY METHODOLOGY: To address these needs, work was carried out to establish a standardized TSP and PM(10) emission inventory methodology for open-pit mining areas. The proposed methodology was applied to seven of the eight mining companies operating in the northern part of Colombia, home to the one of the world's largest open-pit coal mining operations (～70?Mt/year). RESULTS: The results obtained show that transport on unpaved roads is the mining activity that generates most of the emissions and that the total emissions may be reduced up to 72% by spraying water on the unpaved roads. Performance metrics were defined for the emission control programs implemented by mining companies. It was found that coal open-pit mines are emitting 0.726 and 0.180?kg of TSP and PM(10), respectively, per ton of coal produced. It was also found that these mines are using on average 1.148?m(2) of land per ton of coal produced per year.     

燃烧过程颗粒物的形成及我国燃烧源分析

燃料燃烧会排放一次颗粒物和二次颗粒物,一次颗粒物中亚微米粒子主要是由于无机矿物质经蒸发-成核-凝结-凝并的途径形成的;超微米颗粒的产生不同于亚微米颗粒的形成,是由于破碎机理.二次颗粒物是由气态前驱体在大气中转化而成的.我国燃烧源主要是煤燃烧、燃油机动车和农村生活燃料等.深入认识颗粒物的形成及燃烧源的特征对有效控制颗粒物的排放是很有帮助的.     

Monitoring of PM10 and PM2.5 around primary particulate anthropogenic emission sources

Investigations on the monitoring of ambient air levels of atmospheric particulates were developed around a large source of primary anthropogenic particulate emissions: the industrial ceramic area in the province of Castelló (Eastern Spain). Although these primary particulate emissions have a coarse grain-size distribution, the atmospheric transport dominated by the breeze circulation accounts for a grain-size segregation, which results in ambient air particles occurring mainly in the 2.5–10 μm range. The chemical composition of the ceramic particulate emissions is very similar to the crustal end-member but the use of high Al, Ti and Fe as tracer elements as well as a peculiar grain-size distribution in the insoluble major phases allow us to identify the ceramic input in the bulk particulate matter. PM2.5 instead of PM10 monitoring may avoid the interference of crustal particles without a major reduction in the secondary anthropogenic load, with the exception of nitrate. However, a methodology based in PM2.5 measurement alone is not adequate for monitoring the impact of primary particulate emissions (such as ceramic emissions) on air quality, since the major ambient air particles derived from these emissions are mainly in the range of 2.5–10 μm. Consequently, in areas characterised by major secondary particulate emissions, PM2.5 monitoring should detect anthropogenic particulate pollutants without crustal particulate interference, whereas PM10 measurements should be used in areas with major primary anthropogenic particulate emissions.     

A revised estimate of copper emissions from road transport in UNECE-Europe and its impact on predicted copper concentrations

Comparisons of measured and model-predicted atmospheric copper concentrations show a severe underestimation of the observed concentrations by the models. This underestimation may be (partly) due to underestimated emissions of copper to air. Since the phase out of asbestos brake lining material, the composition of brake lining material has changed and may contain up to ∼15% copper. This makes brake wear from vehicles potentially an important source of atmospheric (particulate) copper concentrations. In this paper, we reassess the copper emissions due to exhaust emissions and brake wear from road transport. Overall, our reassessments result in an estimate of total copper emission to air in UNECE-Europe of 4.0–5.5 ktonnes yr⁻¹, which is substantially higher than the previous estimate of 2.8 ktonnes yr⁻¹. Copper concentrations over Europe are calculated with the LOTOS-EUROS model using the revised emission data as model input. The results show that the revised emission estimates are a major step towards gap closure of predicted versus observed copper concentrations in ambient air. Brake wear emissions may be responsible for 50–75% of the total copper emissions to air for most of Western Europe. The hypothesis that road transport is an important source of copper emissions is tested and confirmed by (1) reviewing available literature data of chemically speciated PM data from road tunnel studies and (2) the gradient observed in copper concentrations from ambient PM monitoring going from rural sites to street stations. The literature review and observational data suggest that the majority of the emitted PM10 brake wear particles is in the PM2.5–10 size range. The results of this study indicate that modification of brake lining composition is an important mitigation option to reduce copper exposure of the population in Western Europe.     

Updating the conceptual model for fine particle mass emissions from combustion systems

Atmospheric transformations determine the contribution of emissions from combustion systems to fine particulate matter (PM) mass. For example, combustion systems emit vapors that condense onto existing particles or form new particles as the emissions are cooled and diluted. Upon entering the atmosphere, emissions are exposed to atmospheric oxidants and sunlight, which causes them to evolve chemically and physically, generating secondary PM. This review discusses these transformations, focusing on organic PM. Organic PM emissions are semi-volatile at atmospheric conditions and thus their partitioning varies continuously with changing temperature and concentration. Because organics contribute a large portion of the PM mass emitted by most combustion sources, these emissions cannot be represented using a traditional, static emission factor. Instead, knowledge of the volatility distribution of emissions is required to explicitly account for changes in gas-particle partitioning. This requires updating how PM emissions from combustion systems are measured and simulated from combustion systems. Secondary PM production often greatly exceeds the direct or primary PM emissions; therefore, secondary PM must be included in any assessment of the contribution of combustion systems to ambient PM concentrations. Low-volatility organic vapors emitted by combustion systems appear to be very important secondary PM precursors that are poorly accounted for in inventories and models. The review concludes by discussing the implications that the dynamic nature of these PM emissions have on source testing for emission inventory development and regulatory purposes. This discussion highlights important linkages between primary and secondary PM, which could lead to simplified certification test procedures while capturing the emission components that contribute most to atmospheric PM mass.     

Methods of characterizing the distribution of exhaust emissions from light-duty, gasoline-powered motor vehicles in the U.S. fleet

Mobile sources significantly contribute to ambient concentrations of airborne particulate matter (PM). Source apportionment studies for PM10 (PM < or = 10 microm in aerodynamic diameter) and PM2.5 (PM < or = 2.5 microm in aerodynamic diameter) indicate that mobile sources can be responsible for over half of the ambient PM measured in an urban area. Recent source apportionment studies attempted to differentiate between contributions from gasoline and diesel motor vehicle combustion. Several source apportionment studies conducted in the United States suggested that gasoline combustion from mobile sources contributed more to ambient PM than diesel combustion. However, existing emission inventories for the United States indicated that diesels contribute more than gasoline vehicles to ambient PM concentrations. A comprehensive testing program was initiated in the Kansas City metropolitan area to measure PM emissions in the light-duty, gasoline-powered, on-road mobile source fleet to provide data for PM inventory and emissions modeling. The vehicle recruitment design produced a sample that could represent the regional fleet, and by extension, the national fleet. All vehicles were recruited from a stratified sample on the basis of vehicle class (car, truck) and model-year group. The pool of available vehicles was drawn primarily from a sample of vehicle owners designed to represent the selected demographic and geographic characteristics of the Kansas City population. Emissions testing utilized a portable, light-duty chassis dynamometer with vehicles tested using the LA-92 driving cycle, on-board emissions measurement systems, and remote sensing devices. Particulate mass emissions were the focus of the study, with continuous and integrated samples collected. In addition, sample analyses included criteria gases (carbon monoxide, carbon dioxide, nitric oxide/nitrogen dioxide, hydrocarbons), air toxics (speciated volatile organic compounds), and PM constituents (elemental/organic carbon, metals, semi-volatile organic compounds). Results indicated that PM emissions from the in-use fleet varied by up to 3 orders of magnitude, with emissions generally increasing for older model-year vehicles. The study also identified a strong influence of ambient temperature on vehicle PM mass emissions, with rates increasing with decreasing temperatures.     

Trends in primary particulate matter emissions from Canadian agriculture

Particulate matter (PM) has long been recognized as an air pollutant due to its adverse health and environmental impacts. As emission of PM from agricultural operations is an emerging air quality issue, the Agricultural Particulate Matter Emissions Indicator (APMEI) has been developed to estimate the primary PM contribution to the atmosphere from agricultural operations on Census years and to assess the impact of practices adopted to mitigate these emissions at the soil landscape polygon scale as part of the agri-environmental indicator report series produced by Agriculture and Agri-Food Canada. In the APMEI, PM emissions from animal feeding operations, wind erosion, land preparation, crop harvest, fertilizer and chemical application, grain handling, and pollen were calculated and compared for the Census years of 1981–2006. In this study, we present the results for PM₁₀ and PM_2.5, which exclude chemical application and pollen sources as they only contribute to total suspended particles. In 2006, PM emissions from agricultural operations were estimated to be 652.6 kt for PM₁₀ and 158.1 kt for PM_2.5. PM emissions from wind erosion and land preparation account for most of PM emissions from agricultural operations in Canada, contributing 82% of PM₁₀ and 76% of PM_2.5 in 2006. Results from the APMEI show a strong reduction in PM emissions from agricultural operations between 1981 and 2006, with a decrease of 40% (442.8 kt) for PM₁₀ and 47% (137.7 kt) for PM_2.5. This emission reduction is mainly attributed to the adoption of conservation tillage and no-till practices and the reduction in the area of summerfallow land.

Implications: Increasing sustainability in agriculture often means adapting management practices to have a beneficial impact on the environment while maintaining or increasing production and economic benefits. We developed an inventory of primary PM emissions from agriculture in Canada to better quantify the apportionment, spatial distribution, and trends for Census years 1981–2006. We found major reductions of 40% in PM₁₀ and 47% in PM_2.5 emissions over the 25-yr period as a co-benefit of increasing carbon sequestration in agricultural soils. Indeed, farmers adopted conservation tillage/no-till practices, increased usage of cover crops, and reduced summerfallow, in order to increase soil organic matter and reduce carbon dioxide emissions, which also reduced primary PM emissions, although the agricultural production increased over the period.     

Trace Gases and Particulate Matter Emissions from Wildfires and Agricultural Burning in Northeastern Mexico during the 2000 Fire Season

Abstract

An inventory of air pollutants emitted from forest and agricultural fires in Northeastern Mexico for the period of January to August of 2000 is presented. The emissions estimates were calculated using an emissions factor methodology. The inventory accounts for the emission of carbon monoxide (CO), methane, nonmethane hydrocarbons, ammonia, nitrogen oxides, and particulate matter (PM). Particulate matter emissions include estimates for fine PM and coarse PM. A total of 2479 wildfires were identified in the domain for the period of interest, which represented ~810,000 acres burned and 621,130 short tons emitted (81% being CO). The main source of information used to locate and estimate the extent of the fires came from satellite imagery. A geographic information system was used to determine the type of vegetation burned by each fire. More than 54% of the total area burned during the period of study was land on the State of Tamaulipas. However, >58% of the estimated emissions came from the State of Coahuila. This was because of the mix of vegetation types burned in each state. With respect to the temporal distribution, 76.9% of the fires occurred during the months of April and May consuming almost 78% of the total area burned during the period of study. Analysis of wind forward trajectories of air masses passing through the burned areas and 850-mb wind reanalyses indicate possible transboundary transport of the emissions from Mexico to the United States during the occurrence of the major wildfires identified.     

Trace gases and particulate matter emissions from wildfires and agricultural burning in Northeastern Mexico during the 2000 fire season

An inventory of air pollutants emitted from forest and agricultural fires in Northeastern Mexico for the period of January to August of 2000 is presented. The emissions estimates were calculated using an emissions factor methodology. The inventory accounts for the emission of carbon monoxide (CO), methane, nonmethane hydrocarbons, ammonia, nitrogen oxides, and particulate matter (PM). Particulate matter emissions include estimates for fine PM and coarse PM. A total of 2479 wildfires were identified in the domain for the period of interest, which represented approximately 810,000 acres burned and 621,130 short tons emitted (81% being CO). The main source of information used to locate and estimate the extent of the fires came from satellite imagery. A geographic information system was used to determine the type of vegetation burned by each fire. More than 54% of the total area burned during the period of study was land on the State of Tamaulipas. However, >58% of the estimated emissions came from the State of Coahuila. This was because of the mix of vegetation types burned in each state. With respect to the temporal distribution, 76.9% of the fires occurred during the months of April and May consuming almost 78% of the total area burned during the period of study. Analysis of wind forward trajectories of air masses passing through the burned areas and 850-mb wind reanalyses indicate possible transboundary transport of the emissions from Mexico to the United States during the occurrence of the major wildfires identified.     

Development of a PM2 5 Emissions Inventory for the South Coast Air Basin

ABSTRACT

With the promulgation of a national PM_2.5 ambient air quality standard, it is important that PM_2.5 emissions inventories be developed as a tool for understanding the magnitude of potential PM2.5 violations. Current PM₁₀ inventories include only emissions of primary particulate matter (1 ^ï PM), whereas, based on ambient measurements, both PM₁₀ and PM2.5 emissions inventories will need to include sources of both 1^ï PM and secondary particulate matter (2^ï PM). Furthermore, the U. S. Environmental Protection Agency’s (EPA) current edition of AP-42 includes size distribution data for 1o PM that overestimate the PM_2.5 fraction of fugitive dust sources by at least a factor of 2 based on recent studies.

This paper presents a PM_2.5 emissions inventory developed for the South Coast Air Basin (SCAB) that for the first time includes both 1^ï PM and 2^ï PM. The former is calculated by multiplying PM₁₀ emissions estimates by the PM_2.5/PM₁₀ ratios for different sources. The latter is calculated from estimated emission rates of gas-phase aerosol precursor and gas to aerosol conversion rates consistent with the measured chemical composition of ambient PM_2.5 concentrations observed in the SCAB. The major finding of this PM_2.5 emissions inventory is that the ^2ï aerosol component is more than twice the ^1ï aerosol component, which may result in widely different control strategies being required for fine PM and coarse PM.     

Determination of major natural and anthropogenic source profiles for particulate matter and trace elements in Izmir, Turkey

Samples of PM10 and PM2.5 were collected from several natural and anthropogenic sources using in-stack cyclone, grab sampling/resuspension chamber and ambient air samplers. The chemical characterization of the samples was achieved containing Al, Ba, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, Sr, V and Zn using an inductively coupled plasma-optical emission spectrometer (ICP-OES). The elemental fractions (weight percent by mass), standard deviations and uncertainties were reported. The elemental compositions of PM emitted from mineral industries and cement kiln were dominated by terrestrial elements, particularly Ca, whereas the profile of top-soil mainly contained Al and Ca. The profiles of industrial sources were generally typical for related ones; however, significant differences were obtained for some of them. Similarly, the profiles of fuel burning emissions have significant differences compared to profiles obtained all around the world.     

Trends in primary particulate matter emissions from Canadian agriculture

Particulate matter (PM) has long been recognized as an air pollutant due to its adverse health and environmental impacts. As emission of PM from agricultural operations is an emerging air quality issue, the Agricultural Particulate Matter Emissions Indicator (APMEI) has been developed to estimate the primary PM contribution to the atmosphere from agricultural operations on Census years and to assess the impact of practices adopted to mitigate these emissions at the soil landscape polygon scale as part of the agri-environmental indicator report series produced by Agriculture and Agri-Food Canada. In the APMEI, PM emissions from animal feeding operations, wind erosion, land preparation, crop harvest, fertilizer and chemical application, grain handling, and pollen were calculated and compared for the Census years of 1981-2006. In this study, we present the results for PM10 and PM2.5, which exclude chemical application and pollen sources as they only contribute to total suspended particles. In 2006, PM emissions from agricultural operations were estimated to be 652.6 kt for PM10 and 158.1 kt for PM2.5. PM emissions from wind erosion and land preparation account for most of PM emissions from agricultural operations in Canada, contributing 82% of PM10 and 76% of PM2.5 in 2006. Results from the APMEI show a strong reduction in PM emissions from agricultural operations between 1981 and 2006, with a decrease of 40% (442.8 kt) for PM10 and 47% (137.7 kt) for PM2.5. This emission reduction is mainly attributed to the adoption of conservation tillage and no-till practices and the reduction in the area of summer fallow land.     

Spatial and temporal variations in PM10 and PM2.5 source contributions and comparison to emissions during the 1995 integrated monitoring study

The ambient PM₁₀ and PM_2.5 data collected during the fall and winter portions of the 1995 Integrated Monitoring Study (IMS95) were used to conduct Chemical Mass Balance (CMB) Modeling to determine source contribution estimates. Data from the core and saturation monitoring sites provided an extensive database for evaluating the spatial and temporal variations of contributing sources. Geological sources dominated fall samples, while secondary ammonium nitrate and carbonaceous sources were the largest contributors for winter samples. Secondary ammonium nitrate concentrations were uniform across all sites during both the fall and winter. Site-to-site variability was primarily due to differences in geological contributions in the fall, and carbonaceous source contributions in the winter. During the winter, diurnal profiles of particulate matter (PM) were driven by variations in carbonaceous sources at urban sites, and by variations in secondary ammonium nitrate at rural sites. Although records of day-specific PM activities were recorded during the study, no correlation was observed between 24-h CMB results and specific activities. The ambient data collected during IMS95 was also used to evaluate the adequacy of the emissions inventory. Comparison of ambient and emissions based ratios of NMHC/NO_x, PM/NO_x, CO/NO_x, and SO_x/NO_x suggested that emissions of NMHC and CO in some locations may be underestimated, while emissions for PM and SO_x may be overestimated. Comparison of fractional primary CMB source contribution estimates to corresponding fractional emissions estimates indicated that geological sources were overemphasized in the inventory, while carbonaceous sources were underrepresented.     

Comparison of vehicle activity and emission inventory between Beijing and Shanghai

Vehicle emission inventory is a critical element for air quality study. This study created systemic methods to establish a vehicle emission inventory in Chinese cities. The methods were used to obtain credible results of vehicle activity in Beijing and Shanghai. On the basis of the vehicle activity data, the International Vehicle Emission model is used to establish vehicle emission inventories. The emissions analysis indicates that 3 t of particulate matter (PM), 199 t of nitrogen oxides (NO(x)), 192 t of volatile organic compounds (VOCs), and 2403 t of carbon monoxide (CO) are emitted from on-road vehicles each day in Beijing, whereas 4 t of PM, 189 t of NO(x), 113 t of VOCs, and 1009 t of CO are emitted in Shanghai. Although common features were found in these two cities (many new passenger cars and a high taxi proportion in the fleet), the emission results are dissimilar because of the different local policy regarding vehicles. The method to quantify vehicle emission on an urban scale can be applied to other Chinese cities. Also, knowing how different policies can lead to diverse emissions is beneficial knowledge for other city governments.     

Field Measurements of Particulate Matter Emissions,Carbon Monoxide,and Exhaust Opacity from Heavy-Duty Diesel Vehicles

ABSTRACT

Diesel particulate matter (PM) is a significant contributor to ambient air PM₁₀ and PM_2.5 particulate levels. In addition, recent literature argues that submicron diesel PM is a pulmonary health hazard. There is difficulty in attributing PM emissions to specific operating modes of a diesel engine, although it is acknowledged that PM production rises dramatically with load and that high PM emissions occur during rapid load increases on turbocharged engines. Snap-acceleration tests generally identify PM associated with rapid transient operating conditions, but not with high load. To quantify the origin of PM during transient engine operation, continuous opacity measurements have been made using a Wager 650CP full flow exhaust opacity meter. Opacity measurements were taken while the vehicles were operated over transient driving cycles on a chassis dynamometer using the West Virginia University (WVU) Transportable Heavy Duty Vehicle Emissions Testing Laboratories. Data were gathered from Detroit Diesel, Cummins, Caterpillar, and Navistar heavy-duty (HD) diesel engines. Driving cycles used were the Central Business District (CBD) cycle, the WVU 5-Peak Truck cycle, the WVU 5-Mile route, and the New York City Bus (NYCB) cycle. Continuous opacity measurements, integrated over the entire driving cycle, were compared to total integrated PM mass. In addition, the truck was subjected to repeat snap-acceleration tests, and PM was collected for a composite of these snap-acceleration tests. Additional data were obtained from a fleet of 1996 New Flyer buses in Flint, MI, equipped with electronically controlled Detroit Diesel Series 50 engines. Again, continuous opacity, regulated gaseous emissions, and PM were measured. The relationship between continuous carbon monoxide (CO) emissions and continuous opacity was noted. In identifying the level of PM emissions in transient diesel engine operation, it is suggested that CO emissions may prove to be a useful indicator and may be used to apportion total PM on a continuous basis over a transient cycle. The projected continuous PM data will prove valuable in future mobile source inventory prediction.     

Anthropogenic mercury emissions in China

An inventory of mercury emissions from anthropogenic activities in China is compiled for the year 1999 from official statistical data. We estimate that China's emissions were 536 (±236) t of total mercury. This value includes open biomass burning, but does not include natural sources or re-emission of previously deposited mercury. Approximately 45% of the Hg comes from non-ferrous metals smelting, 38% from coal combustion, and 17% from miscellaneous activities, of which battery and fluorescent lamp production and cement production are the largest. Emissions are heaviest in Liaoning and Guangdong Provinces, where extensive smelting occurs, and in Guizhou Province, where there is much small-scale combustion of high-Hg coal without emission control devices. Emissions are gridded at 30×30 min spatial resolution. We estimate that 56% of the Hg in China is released as Hg⁰, 32% as Hg²⁺, and 12% as Hg^p. Particulate mercury emissions are high in China due to heavy burning of coal in residential and small industrial settings without PM controls. Emissions of Hg²⁺ from coal-fired power plants are high due to the absence of flue-gas desulfurization units, which tend to dissolve the soluble divalent mercury. Metals smelting operations favor the production of elemental mercury. Much of the Hg is released from small-scale activities in rather remote areas, and therefore the activity levels are quite uncertain. Also, emissions test data for Chinese sources are lacking, causing uncertainties in Hg emission factors and removal efficiencies. Overall, we calculate an uncertainty level of ±44% (95% confidence interval) in the estimate of total emissions. We recommend field testing of coal combustors and smelters in China to improve the accuracy of these estimates.     

Evaluation of non-methane hydrocarbon (NMHC) emissions based on an ambient air measurement in Tokyo area,Japan

Non-methane hydrocarbons (NMHCs) are known to have an important role on air quality due to their high reactivity. NMHC analysis has been performed on 148 ambient air samples collected at five different sites in the Kanto area (Tokyo metropolitan area and surrounding six prefectures) of Japan in summer and winter of 2008, and fifty NMHCs have been determined and quantified. A field measurement campaign has been conducted at one of the busiest intersections in Tokyo metropolitan area in winter of 2008. NMHC emissions are evaluated through comparison of distributions of individual NMHCs emitted from motor vehicles, which are estimated from the measurements, with those determined from the current emissions inventory. The comparison revealed that the measured distributions of acetylene, ethylene and toluene showed a good agreement with those estimated from the emissions inventory (the values estimated from the measurements are a factor of 1.5, 0.56 and 2.3 larger than the emissions inventory in median, respectively), however, propane and isobutane are found to be significantly underestimated in the emissions inventory (the measured values were a factor of 18 and 5.1 larger than the emissions inventory, respectively). The significant underestimate of propane can be explained by that the current emissions inventory does not consider emissions from liquefied propane gas (LPG) fueled vehicles. However, for isobutane, reasons for the underestimate are still unclear. Another field measurement has been conducted in summer of 2008, where the air samples have been collected at three different sites on the ground and by a helicopter as well. Remarkable high concentrations of 1-butene and cis- and trans-2-butenes have been sporadically observed in the samples collected at Urayasu in the coastal area of Tokyo bay. Calculated propylene equivalent (PE) concentrations of butenes revealed that those have a significantly important role in ozone formation when the air plume is affected by emissions from their emission sources. The PE concentrations of butenes varied from 0.1 to 39 ppbC, and accounted for 1.5–75% of total PE concentrations at Urayasu. Most of the continuous air quality monitoring stations does not record concentrations of individual hydrocarbons, therefore, the importance of reactive and low concentration hydrocarbon such as butenes might be overlooked in the current emissions inventory and/or air quality model. In this paper, the reliability of NMHC emissions is evaluated based on the field measurements. Their possible impacts on air quality in the Kanto area are discussed as well, based on the calculated propylene equivalent concentrations.     

Source apportionment of ambient total suspended particulates and coarse particulate matter in urban areas of Jiaozuo, China

Approximately 750 total suspended particulates (TSPs) and coarse particulate matter (PM10) filter samples from six urban sites and a background site and >210 source samples were collected in Jiaozuo City during January 2002 to April 2003. They were analyzed for mass and abundances of 25 chemical components. Seven contributive sources were identified, and their contributions to ambient TSP/PM10 levels at the seven sites in three seasons (spring, summer, and winter days) and a "whole" year were estimated by a chemical mass balance (CMB) receptor model. The spatial TSP average was high in spring and winter days at a level of approximately 530 microg/m(3) and low in summer days at 456 microg/m(3); however, the spatial PMo0 average exhibited little variation at a level of approximately 325 microg/m(3), and PM10-to-TSP ratios ranged from 0.58 to 0.81, which suggested heavy particulate matter pollution existing in the urban areas. Apportionment results indicated that geological material was the largest contributor to ambient TSP/PM10 concentrations, followed by dust emissions from construction activities, coal combustion, secondary aerosols, vehicle movement, and other industrial sources. In addition, paved road dust and re-entrained dust were also apportioned to the seven source types and found soil, coal combustion, and construction dust to be the major contributors.