Particulate matter in the indoor air of classrooms—exploratory results from Munich and surrounding area

Numerous epidemiological studies have demonstrated the association between particle mass (PM) concentration in outside air and the occurrence of health related problems and/or diseases. However, much less is known about indoor PM concentrations and associated health risks. In particular, data are needed on air quality in schools, since children are assumed to be more vulnerable to health hazards and spend a large part of their time in classrooms.On this background, we evaluated indoor air quality in 64 schools in the city of Munich and a neighbouring district outside the city boundary. In winter 2004–2005 in 92 classrooms, and in summer 2005 in 75 classrooms, data on indoor air climate parameters (temperature, relative humidity), carbon dioxide (CO₂) and various dust particle fractions (PM₁₀, PM_2.5) were collected; for the latter both gravimetrical and continuous measurements by laser aerosol spectrometer (LAS) were implemented. In the summer period, the particle number concentration (PNC), was determined using a scanning mobility particle sizer (SMPS). Additionally, data on room and building characteristics were collected by use of a standardized form. Only data collected during teaching hours were considered in analysis. For continuously measured parameters the daily median was used to describe the exposure level in a classroom.The median indoor CO₂ concentration in a classroom was 1603 ppm in winter and 405 ppm in summer. With LAS in winter, median PM concentrations of 19.8 μg m⁻³ (PM_2.5) and 91.5 μg m⁻³ (PM₁₀) were observed, in summer PM concentrations were significantly reduced (median PM_2.5=12.7 μg m⁻³, median PM₁₀=64.9 μg m⁻³). PM_2.5 concentrations determined by the gravimetric method were in general higher (median in winter: 36.7 μg m⁻³, median in summer: 20.2 μg m⁻³) but correlated strongly with the LAS-measured results. In explorative analysis, we identified a significant increase of LAS-measured PM_2.5 by 1.7 μg m⁻³ per increase in humidity by 10%, by 0.5 μg m⁻³ per increase in CO₂ indoor concentration by 100 ppm, and a decrease by 2.8 μg m⁻³ in 5–7th grade classes and by 7.3 μg m⁻³ in class 8–11 compared to 1–4th class. During the winter period, the associations were stronger regarding class level, reverse regarding humidity (a decrease by 6.4 μg m⁻³ per increase in 10% humidity) and absent regarding CO₂ indoor concentration. The median PNC measured in 36 classrooms ranged between 2622 and 12,145 particles cm⁻³ (median: 5660 particles cm⁻³).The results clearly show that exposure to particulate matter in school is high. The increased PM concentrations in winter and their correlation with high CO₂ concentrations indicate that inadequate ventilation plays a major role in the establishment of poor indoor air quality. Additionally, the increased PM concentration in low level classes and in rooms with high number of pupils suggest that the physical activity of pupils, which is assumed to be more pronounced in younger children, contributes to a constant process of resuspension of sedimented particles. Further investigations are necessary to increase knowledge on predictors of PM concentration, to assess the toxic potential of indoor particles and to develop and test strategies how to ensure improved indoor air quality in schools.     

Volatile organic compound emissions from Siberian larch

We determined hourly emissions of isoprene, monoterpenes and sesquiterpenes from Siberian larch, one of the major tree species in Siberian forests. Summer volatile organic compounds (VOCs) emission from Siberian larch consisted mainly of monoterpenes (about 90%). The monoterpene emission spectrum remained constant during the measurement period, almost half was sabinene and other major monoterpenes were Δ³-carene, β- and α-pinene. During spring and summer, about 10% of the VOCs were sesquiterpenes, mainly α-farnesene. The sesquiterpene emissions declined to 3% in the fall. Isoprene, 2-methyl-3-buten-2-ol (MBO) and 1,8-cineole contributed to less than 3% of the VOC emission during the whole period. The diurnal variation of the emissions could be explained using a temperature-dependent parameterization. Emission potentials normalized to 30 °C were 5.2–21 μg g_dw⁻¹ h⁻¹ (using β-value of 0.09 °C⁻¹) for monoterpenes and 0.4–1.8 μg g_dw⁻¹ h⁻¹ (using β-value of 0.143 °C⁻¹, mean of determined values) for sesquiterpenes. Normalized monoterpene emission potentials were highest in late summer and elevated again in late fall. Sesquiterpene emission potentials were also highest in late summer, but decreased towards fall.     

Aerosol scattering properties in northern China

The aerosol scattering properties were investigated at two continental sites in northern China in 2004. Aerosol light scattering coefficient (σ_sp) at 525 nm, PM₁₀, and aerosol mass scattering efficiencies (α) at Dunhuang had a mean value of 165.1±148.8 M m⁻¹, 157.6±270.0 μg m⁻³, and 2.30±3.41 m² g⁻¹, respectively, while these values at Dongsheng were, respectively, 180.2±151.9 M m⁻¹, 119.0±112.9 μg m⁻³, and 1.87±1.41 m² g⁻¹. There existed a seasonal variability of aerosol scattering properties. In spring, at Dunhuang PM₁₀, σ_sp, and α were 184.1±211.548 μg m⁻³, 126.3±89.6 M m⁻¹, and 1.05±0.97 m² g⁻¹, respectively, and these values at Dongsheng were 146.4±142.1 μg m⁻³, 183.4±81.7 M m⁻¹, and 1.98±1.52 m² g⁻¹, respectively. However, in winter at Dunhuang PM₁₀, σ_sp, and α were 158.1±261.4 μg m⁻³, 303.3±165.2 M m⁻¹, and 3.17±1.93 m² g⁻¹, respectively, and these values at Dongsheng were 155.7±170.1 μg m⁻³, 304.4±158.1 M m⁻¹, and 2.90±1.72 m² g⁻¹, respectively. σ_sp and α in winter were higher than that in spring at both the sites, which coincides with the characteristics of dust aerosol and pollution aerosol. Overall, the dominant aerosol types in spring and winter at both sites in northern China are dust aerosol and pollution aerosol, respectively.     

The vertical profile of atmospheric heating rate of black carbon aerosols at Kanpur in northern India

Altitude profiles of the mass concentrations of aerosol black carbon (BC) and composite aerosols were obtained from the collocated measurements of these quantities onboard an aircraft, over the urban area of Kanpur, in the Ganga basin of northern India during summer, for the first time in India. The enhancement in the mean BC concentration was observed at ∼1200 m in the summer, but the vertical gradient of BC concentration is less than the standard deviation at that altitude. The difference in the BC altitude profile and columnar concentration in the winter and summer is attributed to the enhanced turbulent mixing within the boundary layer in summer. This effect is more conspicuous with BC than the composite aerosols, resulting in an increase in the BC mass fraction (F_BC) at higher levels in summer. This high BC fraction results in an increase in the lower atmospheric heating rate in both the forenoon, FN and afternoon, AN, but with contrasting altitude profile. The FN profile shows fluctuating trend with highest value (2.1 K day⁻¹) at 300 m and a secondary peak at 1200 m altitudes, whereas the AN profile shows increasing trend with highest value (1.82 K day⁻¹) at 1200 m altitude.     

Trends of ambient carbonyl compounds in the urban environment of Hong Kong

The concentrations of C₁–C₈ carbonyl compounds were measured at two urban sites in Hong Kong from October 1997 to September 2000. The daily total carbonyl concentrations were found to range from 2.4 to 37 μg m⁻³. Formaldehyde was the most abundant species, which comprised from 36 to 43% of the total detected carbonyls, followed by acetaldehyde (18–21%) and acetone (8–20%). The highest 24-hour average concentrations measured were 10 and 7.7 μg m⁻³ for formaldehyde and acetaldehyde, respectively. Seasonal and temporal variations in the concentrations of formaldehyde and acetaldehyde were not obvious, but lowest concentrations often occurred from June to August. The mean formaldehyde/acetaldehyde molar ratios at the two sites in summer (2.8±1.1 and 2.5±1.2) were significantly higher (p⩽0.01) than those in winter periods (1.9±0.6 and 2.0±0.6). The phenomena were explained by influences of both photochemical reactions and local meteorological conditions. Better correlations between formaldehyde and acetaldehyde, and between NO_x and each of the two major carbonyls were obtained in winter periods indicating direct vehicular emissions were the principal sources. The ambient formaldehyde and acetaldehyde concentrations in the urban atmosphere of Hong Kong were within the normal ranges reported in the literature for other urban sites world-wide.     

Fungi and bacteria in mould-damaged and non-damaged office environments in a subarctic climate

The fungi and bacterial levels of the indoor air environments of 77 office buildings were measured in winter and a comparison was made between the buildings with microbe sources in their structures and those without such sources. Penicillium, yeasts, Cladosporium and non-sporing isolates were the commonest fungi detected in the indoor air and in settled dust, in both the mould-damaged and control buildings. Aspergillus ochraceus, Aspergillus glaucus and Stachybotrys chartarium were found only in environmental samples from the mould-damaged buildings. Some other fungi, with growth requiring of water activity, a_w, above 0.85, occurred in both the reference and mould-damaged buildings, but such fungi were commoner in the latter type of buildings. The airborne concentrations of Penicillium, Aspergillus versicolor and yeasts were the best indicators of mould damage in the buildings studied. Penicillium species and A. versicolor were also the most abundant fungi in the material samples. This study showed that the fungi concentrations were very low (2–45 cfu m⁻³ 90% of the concentrations being <15 cfu m⁻³) in the indoor air of the normal office buildings. Although the concentration range of airborne fungi was wider for the mould-damaged buildings (2–2470 cfu m⁻³), only about 20% of the samples exceeded 100 cfu m⁻³. The concentrations of airborne bacteria ranged from 12 to 540 cfu m⁻³ in the control buildings and from 14 to 1550 cfu m⁻³ in the mould-damaged buildings. A statistical analysis of the results indicated that bacteria levels are generally <600 cfu m⁻³ in office buildings in winter and fungi levels are <50 cfu m⁻³. These normal levels are applicable to subarctic climates for urban, modern office buildings when measurements are made using a six-stage impactor. These levels should not be used in evaluations of health risks, but elevated levels may indicate the presence of abnormal microbe sources in indoor air and a need for additional environmental investigations.     

Characteristics of carbonyls: Concentrations and source strengths for indoor and outdoor residential microenvironments in China

Indoor and outdoor carbonyl concentrations were measured simultaneously in 12 urban dwellings in Beijing, Shanghai, Guangzhou, and Xi’an, China in summer (from July to September in 2004) and winter (from December 2004 to February 2005). Formaldehyde was the most abundant indoor carbonyls species, while formaldehyde, acetaldehyde and acetone were found to be the most abundant outdoor carbonyls species. The average formaldehyde concentrations in summer indoor air varied widely between cities, ranging from a low of 19.3 μg m⁻³ in Xi’an to a high of 92.8 μg m⁻³ in Beijing. The results showed that the dwellings with tobacco smoke, incense burning or poor ventilation had significantly higher indoor concentrations of certain carbonyls. It was noticed that although one half of the dwellings in this study installed with low emission building materials or furniture, the carbonyls levels were still significantly high. It was also noted that in winter both the indoor and outdoor acetone concentrations in two dwellings in Guangzhou were significantly high, which were mainly caused by the usage of acetone as industrial solvent in many paint manufacturing and other industries located around Guangzhou and relatively longer lifetime of acetone for removal by photolysis and OH reaction than other carbonyls species. The indoor carbonyls levels in Chinese dwellings were higher than that in dwellings in the other countries. The levels of indoor and ambient carbonyls showed great seasonal differences. Six carbonyls species were carried out the estimation of indoor source strengths. Formaldehyde had the largest indoor source strength, with an average of 5.25 mg h⁻¹ in summer and 1.98 mg h⁻¹ in winter, respectively. However, propionaldehyde, crotonaldehyde and benzaldehyde had the weakest indoor sources.     

Nitric oxide emissions from soils amended with municipal waste biosolids

Land spreading nitrogen-rich municipal waste biosolids (NO₃⁻-N<256 mg N kg⁻¹ dry weight, NH₃-N∼23,080 mg N kg⁻¹ dry weight, Total Kjeldahl N∼41,700 mg N kg⁻¹ dry weight) to human food and non-food chain land is a practice followed throughout the US. This practice may lead to the recovery and utilization of the nitrogen by vegetation, but it may also lead to emissions of biogenic nitric oxide (NO), which may enhance ozone pollution in the lower levels of the troposphere. Recent global estimates of biogenic NO emissions from soils are cited in the literature, which are based on field measurements of NO emissions from various agricultural and non-agricultural fields. However, biogenic emissions of NO from soils amended with biosolids are lacking. Utilizing a state-of-the-art mobile laboratory and a dynamic flow-through chamber system, in-situ concentrations of nitric oxide (NO) were measured during the spring/summer of 1999 and winter/spring of 2000 from an agricultural soil which is routinely amended with municipal waste biosolids. The average NO flux for the late spring/summer time period (10 June 1999–5 August 1999) was 69.4±34.9 ng N m⁻² s⁻¹. Biosolids were applied during September 1999 and the field site was sampled again during winter/spring 2000 (28 February 2000–9 March 2000), during which the average flux was 3.6±1.7 ng N m⁻² s⁻¹. The same field site was sampled again in late spring (2–9 June 2000) and the average flux was 64.8±41.0 ng N m⁻² s⁻¹. An observationally based model, developed as part of this study, found that summer accounted for 60% of the yearly emission while fall, winter and spring accounted for 20%, 4% and 16% respectively. Field experiments were conducted which indicated that the application of biosolids increases the emissions of NO and that techniques to estimate biogenic NO emissions would, on a yearly average, underestimate the NO flux from this field by a factor of 26. Soil temperature and % water filled pore space (%WFPS) were observed to be significant variables for predicting NO emissions, however %WFPS was found to be most significant during high soil temperature conditions. In the range of pH values found at this site (5.8±0.3), pH was not observed to be a significant parameter in predicting NO emissions.     

Seasonal variations in VOC emission rates from gorse (Ulex europaeus)

Seasonal variations of biogenic volatile organic compound (VOC) emission rates and standardised emission factors from gorse (Ulex europaeus) have been measured at two sites in the United Kingdom, from October 1994 to September 1995, within temperature and PAR conditions ranging from 3 to 34°C and 10–1300 μmol m⁻² s⁻¹, respectively. Isoprene was the dominant emitted compound with a relative composition fluctuating from 7% of the total VOC (winter) to 97% (late summer). The monoterpenes α-pinene, camphene, sabinene, β-pinene, myrcene, limonene, trans-ocimene and γ-terpinene were also emitted, with α-pinene being the dominant monoterpene during most the year. Trans-ocimene represented 33–66% of the total monoterpene during the hottest months from June to September. VOC emissions were found to be accurately predicted using existing algorithms. Standard (normalised) emission factors of VOCs from gorse were calculated using experimental parameters measured during the experiment and found to fluctuate with season, from 13.3±2.1 to 0.1±0.1 μg C (g dwt)⁻¹ h⁻¹ in August 1995 and January 1995, respectively, for isoprene, and from 2.5±0.2 to 0.4±0.2 μg C (g dwt)⁻¹ h⁻¹ in July and November 1995, respectively, for total monoterpenes. No simple clear relation was found to allow prediction of these seasonal variations with respect to temperature and light intensity. The effects of using inappropriate algorithms to derive VOC fluxes from gorse were assessed for isoprene and monoterpenes. Although on an annual basis the discrepancies are not significant, monthly estimation of isoprene were found to be overestimated by more than a factor of 50 during wintertime when the seasonality of emission factors is not considered.     

Anhydrosugar and sugar alcohol organic markers associated with carboxylic acids in particulate matter from incense burning

Aerosol from the burning two types of sandalwood-based incense, Hsing Shan and Lao Shan, was analyzed to characterize the chemical profile of total particulate matter emitted. The total particulate matter (PM) mass emission factors were 46.3 ± 2.68 mg g^?1 of Hsing Shan incense and 43.7 ± 1.08 mg g^?1 of Lao Shan incense. Chemical analysis of emissions from the two types of incense revealed that of the 25 components in four groups characterized, anhydrosugars formed the major group, at 46.7–52.2% w/w of the identified particulate and 1078.3–1169.8 μg g^?1 of incense, followed by inorganic salts at 30.4–31.8% w/w of identified particulate and 681.6–734.0 μg g^?1 of incense, carboxylic acids at 12.0–17.1% w/w of the identified particulate and 268.6–392.8 μg g^?1 of incense, and sugar alcohols at 4.44–5.38% w/w of the identified particulate and 102.3–120.6 μg g^?1 of incense. More anhydrosugars and sugar alcohols were emitted from Lao Shan incense than from Hsing Shan incense whereas more carboxylic acids and organic salts were emitted from Hsing Shan than from Lao Shan. These differences were due to structural and functional differences in the young sandalwood used to make Hsing Shan and the aged sandalwood used to make Lao Shan. The anhydrosugar levoglucosan, used as a marker of biomass burning, was always the most abundant species in emitted PM for both incenses (Lao Shan 21.7 mg g^?1 of PM and Hsing Shan 18.7 mg g^?1). K⁺ and Cl^? were the second most abundant components (K⁺ and Cl^? were summed), accounting for 10.6 mg g^?1 of Hsing Shan PM and 9.85 mg g^?1 of Lao Shan PM. The most abundant carboxylic acids in the emissions were formic, acetic, succinic, glutaric and phthalic acid. The latter is a fragrance ingredient and a potential health hazard and was twice as prevalent in Lao Shan emissions. Xylitol was the most prevalent of the sugar alcohols at 35.7–36.6% w/w of total identified sugar alcohols. These abundant species are potential markers for incense burning. K⁺, levoglucosan, mannosan and xylitol are already reported in discriminator ratios for wood burning and it is proposed here that these can and should also apply to incense burning. The calculated discriminator ratios for two types of incense burning reported here are 0.229–0.288 for K/Levo, 12.5–13.5 for Levo/Manno, and 21.5–23.7 for the novel discriminator ratio Levo/Xylitol.     

Atmospheric distribution of polycyclic aromatic hydrocarbons and deposition to Galveston Bay,Texas, USA

Estimates of the atmospheric deposition to Galveston Bay of polycyclic aromatic hydrocarbons (PAHs) are made using precipitation and meteorological data that were collected continuously from 2 February 1995 to 6 August 1996 at Seabrook, TX, USA. Particulate and vapor phase PAHs in ambient air and particulate and dissolved phases in rain samples were collected and analyzed. More than 95% of atmospheric PAHs were in the vapor phase and about 73% of PAHs in the rain were in the dissolved phase. Phenanthrene and napthalene were the dominant compounds in air vapor and rain dissolved phases, respectively, while 5 and 6 ring PAH were predominant in the particulate phase of both air and rain samples. Total PAH concentrations ranged from 4 to 161 ng m⁻³ in air samples and from 50 to 312 ng l⁻¹ in rain samples. Temporal variability in total PAH air concentrations were observed, with lower concentrations in the spring and fall (4–34 ng m ⁻³) compared to the summer and winter (37–161 ng m⁻³). PAHs in the air near Galveston Bay are derived from both combustion and petroleum vaporization. Gas exchange from the atmosphere to the surface water is estimated to be the major deposition process for PAHs (1211 μg m^{− 2} yr^{− 1}), relative to wet deposition (130 μg m⁻² yr^{− 1}) and dry deposition (99 μg m⁻² yr^{− 1}). Annual deposition of PAHs directly to Galveston Bay from the atmosphere is estimated as 2  t yr⁻¹.     

Fungal fragments in moldy houses: A field study in homes in New Orleans and Southern Ohio

Smaller-sized fungal fragments (<1 μm) may contribute to mold-related health effects. Previous laboratory-based studies have shown that the number concentration of fungal fragments can be up to 500 times higher than that of fungal spores, but this has not yet been confirmed in a field study due to lack of suitable methodology. We have recently developed a field-compatible method for the sampling and analysis of airborne fungal fragments. The new methodology was utilized for characterizing fungal fragment exposures in mold-contaminated homes selected in New Orleans, Louisiana and Southern Ohio. Airborne fungal particles were separated into three distinct size fractions: (i) >2.25 μm (spores), (ii) 1.05–2.25 μm (mixture), and (iii) <1.0 μm (submicrometer-sized fragments). Samples were collected in five homes in summer and winter and analyzed for (1→3)-β-d-glucan.The total (1→3)-β-d-glucan varied from 0.2 to 16.0 ng m⁻³. The ratio of (1→3)-β-d-glucan mass in fragment size fraction to that in spore size fraction (F/S) varied from 0.011 to 2.163. The mass ratio was higher in winter (average=1.017) than in summer (0.227) coinciding with a lower relative humidity in the winter. Assuming a mass-based F/S-ratio=1 and the spore size=3 μm, the corresponding number-based F/S-ratio (fragment number/spore number) would be 10³ and 10⁶, for the fragment sizes of 0.3 and 0.03 μm, respectively. These results indicate that the actual (field) contribution of fungal fragments to the overall exposure may be very high, even much greater than that estimated in our earlier laboratory-based studies.     

Ammonia fluxes and derived canopy compensation points over non-fertilized agricultural grassland in The Netherlands using the new gradient ammonia—high accuracy—monitor (GRAHAM)

During a measurement period from June till November 2004, ammonia fluxes above non-fertilized managed grassland in The Netherlands were measured with a Gradient Ammonia—High Accuracy—Monitor (GRAHAM). Compared with earlier ammonia measurement systems, the GRAHAM has higher accuracy and a quality control system.Flux measurements are presented for two different periods, i.e. a warm, dry summer period (from 18 July till 15 August) and a wet, cool autumn period (23 September till 23 October). From these measurements canopy compensation points were derived. The canopy compensation point is defined as the effective surface concentration of ammonia. In the summer period (negative) deposition fluxes are observed in the evening, night and early morning due to leaf surface wetness, while in the afternoon emission fluxes are observed due to high canopy compensation points. The mean NH₃-flux in this period was 4 ng m⁻² s⁻¹, which corresponds to a net emission of 0.10 kg N ha⁻¹ over the 28 day sampling period. The NH₃-flux in the autumn period mainly shows (negative) deposition fluxes due to small canopy compensation points caused by low temperatures and a generally wet surface. The mean NH₃-flux in this period is −24 ng m⁻² s⁻¹, which corresponds to a net deposition of 0.65 kg N ha⁻¹ over the 31 day sampling period.Frequency distributions of the NH₃-concentration and flux show that despite higher average ambient NH₃-concentrations (13.3 μg m⁻³ in the summer period vs. 6.4 μg m⁻³ in the autumn period) there are more emission events in the summer period than in the autumn period (about 50% of the time in summer vs. 20% in autumn). This is caused by the high canopy compensation points in summer due to high temperatures and a dry surface. In autumn, deposition dominates due to a generally wet surface that induces low canopy compensation points.For our non-fertilized agricultural grassland site, the derived canopy compensation points (at temperatures between 7 and 29 °C) varied from 0.5 to 29.7 μg m⁻³ and were on an average 7.0 μg m⁻³, which is quite high for non-fertilized conditions and probably caused by high nitrogen inputs in the past or high dry deposition amounts from local sources. The average value for the ratio between NH₄⁺ and H⁺ concentration in the canopy, Γ_c, that was derived from our data was 2200.     

Properties of organic matter in PM2.5 at Changdao Island,China—A rural site in the transport path of the Asian continental outflow

Fifty-five seasonal PM_2.5 samples were collected March 2003–January 2004 at Changdao, a resort island located at the demarcation line between Bohai Sea and Yellow Sea in Northern China. Changdao is in the transport path of the continental aerosols heading toward the Pacific Ocean in winter and spring due to the East Asia Monsoon. Solvent-extractable organic compounds (SEOC), organic carbon (OC), elemental carbon (EC) and water-soluble organic carbon (WSOC) were analyzed for source identification based on molecular markers. This data set provides useful information for the downstream site researchers of the Asian continental outflow. Total carbon (TC, OC+EC) was ∼18 μg m⁻³ in winter, ∼9 μg m⁻³ in spring and autumn and a large part of the TC was WSOC (33% in winter, >45% in the other seasons). Winter and spring were the high SEOC seasons with n-fatty acids the highest at ∼290 and ∼170 ng m⁻³, respectively, followed by n-alkanes at ∼210 and ∼90 ng m⁻³, and polycyclic aromatic hydrocarbons (PAHs) were also at high at ∼120 and ∼30 ng m⁻³. High WSOC/TC, low C_18:1/C₁₈ of fatty acids, and low concentrations of labile PAHs such as benzo(a)pyrene, together with back trajectory analysis suggested that the aerosols were aged and transported. PAHs, triterpane and sterane distributions provided evidence that coal burning was the main source of the continental outflow. The detection of levoglucosan and β-sitosterol in nearly all the samples showed the impact of biomass burning.     

Multi-year hourly PM2.5 carbon measurements in New York: Diurnal,day of week and seasonal patterns

Multi-year hourly measurements of PM_2.5 elemental carbon (EC) and organic carbon (OC) from a site in the South Bronx, New York were used to examine diurnal, day of week and seasonal patterns. The hourly carbon measurements also provided temporally resolved information on sporadic EC spikes observed predominantly in winter. Furthermore, hourly EC and OC data were used to provide information on secondary organic aerosol formation. Average monthly EC concentrations ranged from 0.5 to 1.4 μg m^?3 with peak hourly values of several μg m^?3 typically observed from November to March. Mean EC concentrations were lower on weekends (approximately 27% lower on Saturday and 38% lower on Sunday) than on weekdays (Monday to Friday). The weekday/weekend difference was more pronounced during summer months and less noticeable during winter. Throughout the year EC exhibited a similar diurnal pattern to NO_x showing a pronounced peak during the morning commute period (7–10 AM EST). These patterns suggest that EC was impacted by local mobile emissions and in addition by emissions from space heating sources during winter months. Although EC was highly correlated with black carbon (BC) there was a pronounced seasonal BC/EC gradient with summer BC concentrations approximately a factor of 2 higher than EC. Average monthly OC concentrations ranged from 1.0 to 4.1 μg m^?3 with maximum hourly concentrations of 7–11 μg m^?3 predominantly in summer or winter months. OC concentrations generally correlated with PM_2.5 total mass and aerosol sulfate and with NO_x during winter months. OC showed no particular day of week pattern. The OC diurnal pattern was typically different than EC except in winter when OC tracked EC and NO_x indicating local primary emissions contributed significantly to OC during winter at the urban location. On average secondary organic aerosol was estimated to account for 40–50% of OC during winter and up to 63–73% during summer months.     

Accumulation of hydroxylated polychlorinated biphenyls (OH-PCBs) and implications for PCBs metabolic capacities in three porpoise species

The present study investigated polychlorinated biphenyls (PCBs) and hydroxylated metabolites of PCBs (OH-PCBs) in blood from three porpoise species: finless porpoises (Neophocaena phocaenoides), harbor porpoises (Phocoena phocoena), and Dall’s porpoises (Phocoenoides dalli). The porpoises were found stranded or were bycaught along the Japanese coast. Concentrations of OH-PCB were the highest in Dall’s porpoises (58 pg g⁻¹ wet wt), second highest in finless porpoises (20 pg g⁻¹ wet wt), and lowest in harbor porpoises (8.3 pg g⁻¹ wet wt). The concentrations in Dall’s porpoises were significantly higher than the concentrations in finless porpoises and harbor porpoises (p < 0.05 and p < 0.01, respectively). There was a positive correlation between PCB and OH-PCB concentrations (r = 0.67, p < 0.001), suggesting the possible concentration-dependent induction of CYP enzymes. The three porpoise species may have exceptionally low metabolic capacities compared with other marine and terrestrial mammals, because low OH-PCB/PCB concentration ratios were found, which were 0.0016 for Dall’s porpoises, 0.0013 for harbor porpoises, and 0.00058 for finless porpoises. Distinct differences in the OH-PCB congener patterns were observed for the three species, even though they are taxonomically closely related.     

Newly characterized products and composition of secondary aerosols from the reaction of α-pinene with ozone

Secondary aerosols from the reaction of α-pinene with ozone were generated in a 190 m³ outdoor Teflon chamber, and products of these aerosols were characterized. Products were separated by gas chromatography and detected with electron-impact mass spectrometry, chemical-impact mass spectrometry, and Fourier transform infrared spectrometry. Because products from the reaction of α-pinene with ozone contain oxidized functional groups such as carboxylic acids and carbonyls, these products are poorly resolved by standard gas chromatography. To use standard chromatographic techniques, derivatization of oxidized functional groups was necessary. Carbonyl products were derivatized with O-(2,3,4,5,6-pentafluorobenzyl) hydroxylamine hydrochloride and carboxylic acids with pentafluorobenzyl bromide. The major identified products were nor-pinonic acid, pinonic acid, 2,2-dimethylcyclobutane-1,3-dicarboxylic acid, pinic acid, and pinonaldehyde. Dicarboxylic acids have lower vapor pressures than either their corresponding di-aldehydes or mono-acids, and have only recently been identified in α-pinene–ozone aerosols. Given their comparatively low vapor pressures, diacids contribute significantly to the aerosol formation process from the reaction of α-pinene with ozone. The composition of these secondary aerosols is strongly influenced by temperature. During the summer experiments, the aerosol composition is dominated by diacids. During the cooler winter experiments, the di-carbonyl and carbonyl-acid products also contributed to the aerosol composition.     

Comprehensive assessment of pine needles as bioindicators of PAHs using multivariate analysis. The importance of temporal trends

The importance of the annual and seasonal trends associated to the polycyclic aromatic hydrocarbons (PAHs) biomonitoring by pine needles are studied with a comprehensive use of univariate and multivariate analysis tools. For this purpose, four pine needle sampling campaigns (winter, spring, summer and autumn 2007) were carried out in 29 sites from Portugal. Needles from Pinus pinaster Ait. and Pinus pinea L. trees were collected from all year-classes available in each tree, corresponding to the different shoots of needles coming out every spring and the results of both species were treated separately. Annual trends of polycyclic aromatic hydrocarbons (PAHs) contamination indicate a general increase from the least to the most exposed year-classes, for all seasons. The mean values for the sum of 16 PAHs ranged from 71 ± 33 ng g⁻¹ (dry weight – dw) for new year (2007) needles in the summer to 514 ± 317 ng g⁻¹ (dw) for 2-year needles (2005) in the spring for P. pinea, and between 90 ± 50 ng g⁻¹ (dw) for new year (2007) needles in the summer and 1212 ± 436 ng g⁻¹ (dw) for 3-year needles (2004) in summer for P. pinaster. The seasonal evolution shows the highest concentrations in the winter, then declining to the lowest levels in the summer and rising again from summer to autumn. Principal component analysis confirmed differences between seasons and needle year-classes, more visible for P. pinea samples. The cooler seasons have more affinity towards the lighter more abundant PAHs, as do the older needles. Differences between both pine species are also evident.     

The continuous field measurements of soluble aerosol compositions at the Taipei Aerosol Supersite,Taiwan

The characteristics of ambient aerosols, affected by solar radiation, relative humidity, wind speed, wind direction, and gas–aerosol interaction, changed rapidly at different spatial and temporal scales. In Taipei Basin, dense traffic emissions and sufficient solar radiation for typical summer days favored the formation of secondary aerosols. In winter, the air quality in Taipei Basin was usually affected by the Asian continental outflows due to the long-range transport of pollutants carried by the winter monsoon. The conventional filter-based method needs a long time for collecting aerosols and analyzing compositions, which cannot provide high time-resolution data to investigate aerosol sources, atmospheric transformation processes, and health effects. In this work, the in situ ion chromatograph (IC) system was developed to provide 15-min time-resolution data of nine soluble inorganic species (Cl⁻, NO₂⁻, NO₃⁻, SO₄²⁻, Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺). Over 89% of all particles larger than approximately 0.056 μm were collected by the in situ IC system. The in situ IC system is estimated to have a limit of detection lower than 0.3 μg m⁻³ for the various ambient ionic components. Depending on the hourly measurements, the pollutant events with high aerosol concentrations in Taipei Basin were associated with the local traffic emission in rush hour, the accumulation of pollutants in the stagnant atmosphere, the emission of industrial pollutants from the nearby factories, the photochemical secondary aerosol formation, and the long-range transport of pollutants from Asian outflows.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.