Comparison of carbonyl compounds emissions from diesel engine fueled with biodiesel and diesel

The characteristics of carbonyl compounds emissions were investigated on a direct injection, turbocharged diesel engine fueled with pure biodiesel derived from soybean oil. The gas-phase carbonyls were collected by 2,4-dinitrophenylhydrazine (DNPH)-coated silica cartridges from diluted exhaust and analyzed by HPLC with UV detector. A commercial standard mixture including 14 carbonyl compounds was used for quantitative analysis. The experimental results indicate that biodiesel-fueled engine almost has triple carbonyls emissions of diesel-fueled engine. The weighted carbonyls emission of 8-mode test cycle of biodiesel is 90.8 mg (kW h)^?1 and that of diesel is 30.7 mg (kW h)^?1. The formaldehyde is the most abundant compound of carbonyls for both biodiesel and diesel, taking part for 46.2% and 62.7% respectively. The next most significant compounds are acetaldehyde, acrolein and acetone for both fuels. The engine fueled with biodiesel emits a comparatively high content of propionaldehyde and methacrolein. Biodiesel, as an alternative fuel, has lower specific reactivity (SR) caused by carbonyls compared with diesel. When fueled with biodiesel, carbonyl compounds make more contribution to total hydrocarbon emission.     

Reducing carbonyl emissions from a heavy-duty diesel engine at US transient cycle test by use of paraffinic/biodiesel blends

Formaldehyde and acetaldehyde are toxic carcinogens so their reductions in diesel-engine emissions are desirable. This study investigated emissions of carbonyl compounds (CBCs) from an HDDE (heavy-duty diesel engine) at US transient cycle test, using five test fuels: premium diesel fuel (D100), P100 (100% palm-biodiesel), P20 (20% palm-biodiesel + 80% premium diesel fuel), PF80P20 (80% paraffinic fuel + 20% palm-biodiesel), and PF95P05 (95% paraffinic fuel + 5% palm-biodiesel). Experimental results indicate that formaldehyde was the major carbonyl in the exhaust, accounting for 70.1–76.2% of total CBC concentrations for all test fuels. In comparison with D100 (172 mg BHP^?1 h^?1), the reductions of formaldehyde and acetaldehyde emission factor for P100, P20, PF80P20, and PF95P05 were (?16.8%, ?61.8%), (?10.0%, ?39.0%), (21.3%, 1.10%), and (31.1%, 19.5%), respectively. Using P100 and P20 instead of D100 in the HDDE increased CBC concentrations by 14.5% and 3.28%, respectively, but using PF80P20 and PF95P05 significantly reduced CBC concentrations by 30.3% and 23.7%, respectively. Using P100 and P20 instead of D100 (2867 ton yr^?1) in the HDDE increased CBC emissions by 240 and 224 ton yr^?1, respectively, but using PF80P20, and PF95P05 instead of D100 in the HDDE decreased CBC emissions by 711 and 899 ton yr^?1, respectively. The above results indicate that the wide usage of paraffinic–palmbiodiesel blends as alternative fuels could protect the environment.     

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NO_x) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NO_X standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines’ regulated emissions of PM, NO_X, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially (90 to >99%) lower than pre-2007-technology engine emissions, and also substantially (46 to >99%) lower than the 2007-technology engine emissions characterized in the previous study.

Implications:?Heavy-duty on-highway diesel engines equipped with DOC/DPF/SCR/AMOX and fueled with ultra-low-sulfur diesel fuel produced lower emissions than the stringent 2010 emission standards established by the U.S. Environmental Protection Agency. They also resulted in significant reductions in a wide range of unregulated toxic emission compounds relative to older technology engines. The increased use of newer technology (2010+) diesel engines in the on-highway sector and the adaptation of such technology by other sectors such as nonroad, displacing older, higher emissions engines, will have a positive impact on ambient levels of PM, NOx, and volatile organic compounds, in addition to many other toxic compounds.     

Carbonyl emissions from vehicular exhausts sources in Hong Kong

Vehicular emission (VE) is one of the important anthropogenic sources for airborne carbonyls in urban area. Six types of VE-dominated samples were collected at representative locations in Hong Kong where polluted by a particular fueled type of vehicles, including (i) a gas refilling taxis station (liquefied petroleum gas [LPG] emission); (ii) a light-duty passenger car park (gasoline emission); (iii) a minibus station (diesel emission); (iv) a single-deck-bus depot (diesel emission); (v) a double-deck-bus depot (diesel emission); and (vi) a whole-food market entrance for light- and heavy-duty vehicles (diesel emission). A total of 15 carbonyls in the samples were quantified. Formaldehyde was the most abundant carbonyl among the VE-dominated samples, and its contribution to the total quantified amount on a molar basis ranged from 54.8% to 60.8%. Acetaldehyde and acetone were the next two abundant carbonyls. The carbonyls were quantified at three roadside locations in Hong Kong. The highest concentrations of formaldehyde and acetaldehyde, 22.7 +/- 8.4 and 6.0 +/- 2.8 microg/m3, respectively, were determined in the samples collected at a main transportation gate for goods between Hong Kong and Mainland China. The total quantified carbonyl concentration, 37.9 +/- 9.3 microg/m3, was the highest at an entrance of a cross-harbor tunnel in downtown area. The theoretical carbonyls compositions of the three roadside locations were estimated according to the VE-dominated sample profiles and the statistics on vehicle numbers and types during the sampling period. The measured compositions of formaldehyde were much higher than the theoretical compositions in summer, demonstrating that photochemical reactions significantly contributed to the formaldehyde production in the roadsides.     

Carbonyl emissions from commercial cooking sources in Hong Kong

Cooking fumes are an important carbonyl emission source, especially in a highly urbanized city, such as Hong Kong. Cooking exhaust from 15 commercial kitchens of a variety of cooking styles was sampled and analyzed for a suite of 13 carbonyl compounds. Carbonyl compositions were varied among the different cooking styles. Formaldehyde was generally the most abundant carbonyl, and its contribution to the total carbonyl amount on a molar basis ranged from 12 to 60%. Acrolein was also found to be an abundant carbonyl in the cooking exhaust. The highest contribution by acrolein to the total carbonyls was found to be 30% in the exhaust of a western-style steak restaurant. Long-chain saturated carbonyls, that is, heptanal, octanal, and nonanal, accounted for a significant fraction (> 40%) of the total carbonyls in kitchens that always used heated cooking oils. Two dicarbonyls, glyoxal and methylglyoxal, had a various presence in the cooking emissions, ranging from negligible to 10%. The presence of benzaldehyde and tolualdehyde was mostly negligible in the sampled kitchen exhaust. Annual emission rates of both individual carbonyls and total carbonyls were estimated for various types of commercial kitchens. Local-style fast-food shops contributed the highest total carbonyl emissions per year mainly because of the large number of this kind of restaurant in Hong Kong. The citywide annual emission rates of the three most toxic carbonyls, formaldehyde, acetaldehyde, and acrolein, were estimated assuming that the limited number of sampled restaurants were representative of the average restaurants. Such estimates of carbonyl emission rates were comparable to the estimated carbonyl emissions from vehicular sources, suggesting the importance of commercial cooking as a source for carbonyls in Hong Kong.     

Carbonyl Emissions from Commercial Cooking Sources in Hong Kong

Abstract

Cooking fumes are an important carbonyl emission source, especially in a highly urbanized city, such as Hong Kong. Cooking exhaust from 15 commercial kitchens of a variety of cooking styles was sampled and analyzed for a suite of 13 carbonyl compounds. Carbonyl compositions were varied among the different cooking styles. Formal dehyde was generally the most abundant carbonyl, and its contribution to the total carbonyl amount on a molar basis ranged from 12 to 60%. Acrolein was also found to be an abundant carbonyl in the cooking exhaust. The highest contribution by acrolein to the total carbonyls was found to be 30% in the exhaust of a western-style steak restaurant. Long-chain saturated carbonyls, that is, heptanal, octanal, and nonanal, accounted for a signifi-cant fraction (>40%) of the total carbonyls in kitchens that always used heated cooking oils. Two dicarbonyls, glyoxal and methylglyoxal, had a various presence in the cooking emissions, ranging from negligible to 10%. The presence of benzaldehyde and tolualdehyde was mostly negligible in the sampled kitchen exhaust. Annual emission rates of both individual carbonyls and total carbon-yls were estimated for various types of commercial kitchens. Local-style fast-food shops contributed the highest total carbonyl emissions per year mainly because of the large number of this kind of restaurant in Hong Kong. The citywide annual emission rates of the three most toxic carbonyls, formaldehyde, acetaldehyde, and acrolein, were estimated assuming that the limited number of sampled restaurants were representative of the average restaurants. Such estimates of carbonyl emission rates were comparable to the estimated carbonyl emissions from vehicular sources, suggesting the importance of commercial cooking as a source for carbonyls in Hong Kong.     

Size and composition distributions of particulate matter emissions: part 2--heavy-duty diesel vehicles

Particulate matter (PM) emissions from heavy-duty diesel vehicles (HDDVs) were collected using a chassis dynamometer/dilution sampling system that employed filter-based samplers, cascade impactors, and scanning mobility particle size (SMPS) measurements. Four diesel vehicles with different engine and emission control technologies were tested using the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) 5 mode driving cycle. Vehicles were tested using a simulated inertial weight of either 56,000 or 66,000 lb. Exhaust particles were then analyzed for total carbon, elemental carbon (EC), organic matter (OM), and water-soluble ions. HDDV fine (< or =1.8 microm aerodynamic diameter; PM1.8) and ultrafine (0.056-0.1 microm aerodynamic diameter; PM0.1) PM emission rates ranged from 181-581 mg/km and 25-72 mg/km, respectively, with the highest emission rates in both size fractions associated with the oldest vehicle tested. Older diesel vehicles produced fine and ultrafine exhaust particles with higher EC/OM ratios than newer vehicles. Transient modes produced very high EC/OM ratios whereas idle and creep modes produced very low EC/OM ratios. Calcium was the most abundant water-soluble ion with smaller amounts of magnesium, sodium, ammonium ion, and sulfate also detected. Particle mass distributions emitted during the full 5-mode HDDV tests peaked between 100-180 nm and their shapes were not a function of vehicle age. In contrast, particle mass distributions emitted during the idle and creep driving modes from the newest diesel vehicle had a peak diameter of approximately 70 nm, whereas mass distributions emitted from older vehicles had a peak diameter larger than 100 nm for both the idle and creep modes. Increasing inertial loads reduced the OM emissions, causing the residual EC emissions to shift to smaller sizes. The same HDDV tested at 56,000 and 66,000 lb had higher PM0.1 EC emissions (+22%) and lower PM0.1 OM emissions (-38%) at the higher load condition.     

Emission profile of 18 carbonyl compounds,CO, CO2, and NOx emitted by a diesel engine fuelled with diesel and ternary blends containing diesel,ethanol and biodiesel or vegetable oils

The impact of vehicular emissions on air depends, among other factors, on the composition of fuel and the technology used to build the engines. The reduction of vehicular emissions requires changes in the fuel composition, and improving the technologies used in the manufacturing of engines and for the after-treatment of gases. In general, improvements to diesel engines have targeted not only emission reductions, but also reductions in fuel consumption. However, changes in the fuel composition have been shown to be a more rapid and effective alternative to reduce pollution. Some factors should been taken into consideration when searching for an alternative fuel to be used in diesel engines, such as emissions, fuel stability, availability and its distribution, as well as its effects on the engine durability. In this work, 45 fuel blends were prepared and their stability was evaluated. The following mixtures (v/v/v) were stable for the 90-day period and were used in the emission study: diesel/ethanol – 90/10%, diesel/ethanol/soybean biodiesel – 80/15/5%, diesel/ethanol/castor biodiesel – 80/15/5%, diesel/ethanol/residual biodiesel – 80/15/5%, diesel/ethanol/soybean oil – 90/7/3%, and diesel/ethanol/castor oil – 90/7/3%. The diesel/ethanol fuel showed higher reduction of NO_x emission at a lower load (2 kW) when compared with pure diesel. The other fuels showed a decrease of NO_x emissions in the ranges of 6.9–75% and 4–85% at 1800 rpm and 2000 rpm, respectively. The combustion efficiencies of the diesel can be enhanced by the addition of the oxygenate fuels, like ethanol and biodiesel/vegetable oil, resulting in a more complete combustion in terms of NO_x emission. In the case of CO₂ the decreases were in the ranges of 5–24% and 4–6% at 1800 rpm and 2000 rpm, respectively. Meanwhile, no differences were observed in CO emission. The carbonyl compounds (CC) studied were formaldehyde, acetaldehyde, propionaldehyde, acrolein, acetone, crotonaldehyde, butyraldehyde, butanone, benzaldehyde, isovaleraldehyde, valeraldehyde, o-toluenaldehyde, m-toluenaldehyde, p-toluenaldehyde, hexaldehyde, octaldehyde, 2,5-dimethylbenzaldehyde, and decaldehyde. Among them, formaldehyde, acetaldehyde, acetone, and propionaldehyde showed the highest emission concentrations. When ternary blend contains vegetable oil, there is a strong tendency to increase the emissions of the high weight CC and decrease the emissions of the low weight CC. The highest concentration of acrolein was observed when the fuel contains diesel, ethanol and biodiesel. With the exception of NO_x, the use of ternary blended fuels resulted on the increase in the emission rates of the studied compounds.     

Comparison of vehicle exhaust emissions from modified diesel fuels

Three diesel fuels, one oil sand-derived (OSD) diesel serving as base fuel, one cetane-enhanced base fuel, and one oxygenate [diethylene glycol dimethyl ether (DEDM)]-blended base fuel, were tested for their emission characterizations in vehicle exhaust on a light-duty diesel truck that reflects the engine technology of the 1994 North American standard. Both the cetane-enhanced and the oxygenate-blended fuels were able to reduce regulated [CO, particulate matter (PM), total hydrocarbon (THC)] and nonregulated [polyaromatic hydrocarbons (PAHs), carbonyls, and other volatile organic chemicals] emissions, except for nitrogen oxides (NO(x)), compared with the base fuel. Although burning a fuel that contains oxygen could conceivably yield more oxygenated compounds in emissions, the oxygenate-blended diesel fuel resulted in reduced emissions of formaldehyde along with hydrocarbons such as benzene, 1,3-butadiene, and PAHs. Reductions in nitro-PAH emissions have been observed in both the cetane-enhanced and oxygenated fuels. This further demonstrates the benefits of using a cetane enhancer and the oxygenated fuel component.     

Indoor and outdoor carbonyl compounds in the hotel ballrooms in Guangzhou,China

Twenty-one carbonyl compounds were measured simultaneously at four hotel ballrooms in urban Guangzhou during the autumn, 2002. In each ballroom, measurements were carried out in business hours in the evening (20:30–24:00) on 7 consecutive days without any disturbance of the ballroom's normal operation. Nineteen out of the 21 target carbonyl compounds were identified in indoor and outdoor air. In the outdoor environment, formaldehyde was the most abundant carbonyl, followed by acetaldehyde, and there existed a strong correlation between formaldehyde and acetaldehyde. In the indoor air, however, acetaldehyde was the most abundant carbonyl, its concentrations seemed to be affected significantly by smoking. The indoor concentrations of carbonyls were found higher than their outdoor counterparts with only a few exceptions. Further studies concerning the indoor/outdoor ratios and mutual correlation of the carbonyls indicated that apart from direct emission from indoor materials and infiltration of outdoor air, other anthropogenic sources, e.g. tobacco smoke, also significantly contributed to carbonyl compounds. The possible sources of some high molecular weight carbonyls, e.g. nonanaldehyde, were also discussed briefly. Preliminary estimate of the exposures and risks due to carbonyls in the ballrooms was made, which indicated that long-term exposure in such places might cause increased chance of developing cancers.     

Regulated and unregulated emissions from a diesel engine fueled with biodiesel and biodiesel blended with methanol

Experiments were carried out on a diesel engine operating on Euro V diesel fuel, pure biodiesel and biodiesel blended with methanol. The blended fuels contain 5%, 10% and 15% by volume of methanol. Experiments were conducted under five engine loads at a steady speed of 1800 rev min⁻¹ to assess the performance and the emissions of the engine associated with the application of the different fuels. The results indicate an increase of brake specific fuel consumption and brake thermal efficiency when the diesel engine was operated with biodiesel and the blended fuels, compared with the diesel fuel. The blended fuels could lead to higher CO and HC emissions than biodiesel, higher CO emission but lower HC emission than the diesel fuel. There are simultaneous reductions of NO_x and PM to a level below those of the diesel fuel. Regarding the unregulated emissions, compared with the diesel fuel, the blended fuels generate higher formaldehyde, acetaldehyde and unburned methanol emissions, lower 1,3-butadiene and benzene emissions, while the toluene and xylene emissions not significantly different.     

Comparison of the effect of biodiesel-diesel and ethanol-diesel on the gaseous emission of a direct-injection diesel engine

Experiments were conducted on a 4-cylinder direct-injection diesel engine using ultralow sulfur diesel blended with biodiesel and ethanol to investigate the gaseous emissions of the engine under five engine loads at the maximum torque engine speed of 1800 rev min^?1. Four biodiesel blended fuels and four ethanol blended fuels with oxygen concentrations of 2%, 4%, 6% and 8% were used. With the increase of oxygen content in the blended fuels, the brake thermal efficiency improves slightly.For the diesel-biodiesel fuels, the brake specific HC and CO emissions decrease while the brake specific NO_x and NO₂ emissions increase. The emissions of formaldehyde, 1,3-butadiene, toluene, xylene and overall BTX (benzene, toluene, xylene) in general decrease, however, acetaldehyde and benzene emissions increase. For the diesel-ethanol fuels, the brake specific HC and CO emissions increase significantly at low engine load, NO_x emission decreases at low engine load but increases at high engine load. The emissions of benzene and BTX vary with engine load and ethanol content. Similar to the biodiesel-diesel fuels, the formaldehyde, 1,3-butadiene, toluene and xylene emissions decrease while the acetaldehyde and NO₂ emissions increase. Despite having the same oxygen contents in the blended fuels, there are significant differences in the gaseous emissions between the biodiesel-diesel blends and the ethanol-diesel blends.     

Emissions of isoprene,monoterpene and short-chained carbonyl compounds from Eucalyptus spp. in southern Australia

Eucalypts are among the highest emitters of biogenic volatile organic compounds, yet there is relatively little data available from field studies of this genus. Emissions of isoprene, monoterpenes and the short-chained carbonyls formaldehyde, acetaldehyde and acetone were determined from four species (Eucalyptus camaldulensis, Eucalyptus globulus, Eucalyptus grandis, and Eucalytpus viminalis) in Australia. A smaller comparative study was conducted on E. camaldulensis in south-eastern Australia. Carbonyl emissions, reported here for the first time from eucalypts, were generally comparable with rates reported for other species, with diurnal emissions peaking at about 4, 75 and 34 nmol m^?2 min^?1 for acetone, formaldehyde and acetaldehyde respectively. There was wide variation in diurnal isoprene and monoterpene emissions between species, but under standard conditions, isoprene emissions were much lower than previous reports. Conversely, standard emission rates of monoterpenes were as much as six times greater than previous reports for some species. Emission of each carbonyl was correlated with its ambient concentration across different species, but more weakly related to temperature. Acetaldehyde emission in particular was significantly correlated with transpiration, but not with sap flow or with ethanol concentrations in xylem sap, suggesting fermentation within the leaf and stomatal conductance are primary controlling processes. Differences in acetaldehyde exchange velocities between sites, in addition to transpiration differences, suggest stomata may indeed exert long term emission regulation, in contrast to compounds for which no biological sink exists.     

Characterization of polycyclic aromatic hydrocarbons from the diesel engine by adding light cycle oil to premium diesel fuel

Diesel fuels governed by U.S. regulations are based on the index of the total aromatic contents. Three diesel fuels, containing various fractions of light cycle oil (LCO) and various sulfur, total polyaromatic, and total aromatic contents, were used in a heavy-duty diesel engine (HDDE) under transient cycle test to assess the feasibility of using current indices in managing the emissions of polycyclic aromatic hydrocarbons (PAHs) from HDDE. The mean sulfur content in LCO is 20.8 times as much as that of premium diesel fuel (PDF). The mean total polyaromatic content in LCO is 28.7 times as much as that of PDF, and the mean total aromatic content in LCO is 2.53 times as much as that of PDF. The total polyaromatic hydrocarbon emission factors in the exhaust from the diesel engine, as determined using PDF L3.5 (3.5% LCO and 96.5% PDF), L7.5 (7.5% LCO and 92.5% PDF), and L15 (15% LCO and 85% PDF) were 14.3, 25.8, 44, and 101 mg L(-1), respectively. The total benzo(a)pyrene equivalent (BaPeq) emission factors in the exhaust from PDF, L3.5, L7.5, and L15 were 0.0402, 0.121, 0.219, and 0.548 mg L(-1), respectively. Results indicated that using L3.5 instead of PDF will result in an 80.4% and a 201% increase of emission for total PAHs and total BaPeq, respectively. The relationships between the total polyaromatic hydrocarbon emission factor and the two emission control indices, including fuel polyaromatic content and fuel aromatic content, suggest that both indices could be used feasibly to regulate total PAH emissions. These results strongly suggest that LCO used in the traveling diesel vehicles significantly influences PAH emissions.     

Trends of ambient carbonyl compounds in the urban environment of Hong Kong

The concentrations of C₁–C₈ carbonyl compounds were measured at two urban sites in Hong Kong from October 1997 to September 2000. The daily total carbonyl concentrations were found to range from 2.4 to 37 μg m⁻³. Formaldehyde was the most abundant species, which comprised from 36 to 43% of the total detected carbonyls, followed by acetaldehyde (18–21%) and acetone (8–20%). The highest 24-hour average concentrations measured were 10 and 7.7 μg m⁻³ for formaldehyde and acetaldehyde, respectively. Seasonal and temporal variations in the concentrations of formaldehyde and acetaldehyde were not obvious, but lowest concentrations often occurred from June to August. The mean formaldehyde/acetaldehyde molar ratios at the two sites in summer (2.8±1.1 and 2.5±1.2) were significantly higher (p⩽0.01) than those in winter periods (1.9±0.6 and 2.0±0.6). The phenomena were explained by influences of both photochemical reactions and local meteorological conditions. Better correlations between formaldehyde and acetaldehyde, and between NO_x and each of the two major carbonyls were obtained in winter periods indicating direct vehicular emissions were the principal sources. The ambient formaldehyde and acetaldehyde concentrations in the urban atmosphere of Hong Kong were within the normal ranges reported in the literature for other urban sites world-wide.     

Effect of fuel aromatic content on PAH emission from a heavy-duty diesel engine

Polycyclic aromatic hydrocarbons (PAHs) emission tests for a heavy-duty diesel engine fueled with blend base diesel fuel by adding batch fractions of poly-aromatic and mono-aromatic hydrocarbons, Fluorene and Toluene, respectively, were simulated to five steady-state modes by a DC-current dynamometer with fully automatic control system. The main objective of this study is to investigate the effect of total aromatic content and poly-aromatic content in diesel fuels on PAH emission from the HDD engine exhaust under these steady-state modes. The results of this study revealed that adding 3% and 5% (fuel vol%) Fluorene in the diesel fuel increases the amount of total-PAH emission by 2.6 and 5.7 times, respectively and increases the amount of Fluorene emission by 52.9 and 152 times, respectively, than no additives. However, there was no significant variation of PAH emission by adding 10% (vol%) of Toluene. To regulate the content of poly-aromatic content in diesel fuel, in contrast to the total aromatic content, will be more suitable for the management of PAH emission.     

Review of light-duty diesel and heavy-duty diesel gasoline inspection programs

Emissions from diesel vehicles and gas-powered heavy-duty vehicles are becoming a new focus of many inspection and maintenance (I/M) programs. Diesel particulate matter (PM) is increasingly becoming more recognized as an important health concern, while at the same time, the public awareness of diesel PM emissions because of their visibility have combined to increase the focus on diesel emissions in the United States. This has resulted in an increased interest by some states in including heavy-duty vehicle testing in their I/M program. This paper provides an overview of existing I/M programs focused on testing light-duty diesel vehicles, heavy-duty diesel vehicles, and heavy-duty gasoline vehicles (HDGVs). Information on 39 I/M programs in 27 different states in the United States plus 9 international inspection programs is included. Information on the status of diesel emissions technology and current test procedures is also presented. The goal is to provide useful information for air quality managers as they work to decide whether such I/M programs would be worth pursuing in their respective areas and in evaluating the emissions measurement technology to be used in the program. Testing of HDGVs is generally limited to idle testing, because dynamometer testing of these vehicles is not practical, and most were not certified on a chassis basis. Testing of diesel vehicles has mostly been limited to SAE J1667 "snap-idle" opacity testing. Cost-effective technology for measuring diesel emissions currently does not exist, and, therefore, opacity-type measurements, although not effective at reducing the pollutants of most significant health concern, will continue to be used.     

Characterization of hydrocarbons, halocarbons and carbonyls in the atmosphere of Hong Kong

Ambient air quality measurements of 156 species including 39 alkanes, 32 alkenes, 2 alkynes, 24 aromatic hydrocarbons, 43 halocarbons and 16 carbonyls, were carried out for 120 air samples collected at two sampling stations (CW and TW) in 2001 throughout Hong Kong. Spatial variations of volatile organic compounds (VOCs) in the atmosphere were investigated. Levels of most alkanes and alkenes at TW site were higher than that at the CW site, while the BTEX concentrations at the two sites were close. The BTEX ratios at CW and TW were 1.6:10.1:1.0:1.6 and 2.1:10.8:1.0:2.0, respectively. For major halogenated hydrocarbons, the mean concentrations of chloromethane, CFCs 12 and 22 did not show spatial variations at the two sites. However, site-specific differences were observed for trichloroethene and tetrachloroethene. Furthermore, there were no significant differences for carbonyls such as formaldehyde, acetaldehyde and acetone between the two sites. The levels of selected hydrocarbons in winter were 1-5 times that in summer. There were no common seasonal trends for carbonyls in Hong Kong. The ambient level of formaldehyde, the most abundant carbonyl, was higher in summer. However, levels of acetaldehyde, acetone and benzaldehyde in winter were 1.6-3.8 times that in summer. The levels of CFCs 11 and 12, and chloromethane in summer were higher than that in winter. Strong correlation of most hydrocarbons with propene and n-butane suggested that the primary contributors of hydrocarbons were vehicular emissions in Hong Kong. In addition, gasoline evaporation, use of solvents, leakage of liquefied petroleum gas (LPG), natural gas leakage and other industrial emissions, and even biogenic emissions affected the ambient levels of hydrocarbons. The sources of halocarbons were mainly materials used in industrial processes and as solvents. Correlation analysis suggested that photochemical reactions made significant contributions to the ambient levels of carbonyls in summer whereas in winter motor vehicle emissions would be the major sources of the carbonyls. The photochemical reactivity of selected VOCs was estimated in this study. The largest contributors to ozone formation were formaldehyde, toluene, propene, m,p-xylene, acetaldehyde, 1-butene/i-butene, isoprene and n-butane, suggesting that motor vehicles, gasoline evaporation, use of solvents, leakage of LPG, photochemical processes and biogenic emission are sources in the production of ozone. On the other hand, VOCs from vehicles and gasoline evaporation were predominant with respect to reactions with OH radical.     

Regulated emissions from biodiesel fuels from on/off-road applications

This research is one of the largest studies of biodiesel in both on-road and off-road uses. The testing was conducted for the military and encompassed a wide range of application types including two medium-duty trucks, two Humvees, a heavy heavy-duty diesel truck, a bus, two stationary backup generators (BUGs), a forklift, and an airport tow vehicle. The full range of fuels tested included a California ultra-low sulfur diesel (ULSD) fuel, different blend ratios of two different yellow-grease biodiesels and one soy-based biodiesel, JP-8, and yellow-grease biodiesel blends with two different NO_x reduction additives. The B20-YGA, B20-YGB, and B20-Soy did not show trends relative to ULSD that were consistent over all applications tested. Higher biodiesel blends were tested on only one vehicle, but showed a tendency for higher total hydrocarbons (THC) and carbon monoxide (CO) emissions and lower particulate matter (PM) emissions. The JP-8 showed increases in THC and CO relative to the ULSD.     

Factors affecting heavy-duty diesel vehicle emissions

Societal and governmental pressures to reduce diesel exhaust emissions are reflected in the existing and projected future heavy-duty certification standards of these emissions. Various factors affect the amount of emissions produced by a heterogeneous charge diesel engine in any given situation, but these are poorly quantified in the existing literature. The parameters that most heavily affect the emissions from compression ignition engine-powered vehicles include vehicle class and weight, driving cycle, vehicle vocation, fuel type, engine exhaust aftertreatment, vehicle age, and the terrain traveled. In addition, engine control effects (such as injection timing strategies) on measured emissions can be significant. Knowing the effect of each aspect of engine and vehicle operation on the emissions from diesel engines is useful in determining methods for reducing these emissions and in assessing the need for improvement in inventory models. The effects of each of these aspects have been quantified in this paper to provide an estimate of the impact each one has on the emissions of diesel engines.